Search Documents

[ ]

Jan 1, 1938

By D. M. MacLean

THE property of Howey Gold Mines, Limited, is situated at Red Lake, Ontario, one hundred and seventy-five miles east of Winnipeg and eighty miles north of the Canadian National railway. The mine has been a continuous producer since April, 1930, and, at present writing, a total of 3,042,690 tons has been hoisted, giving a production of $6,422,858.55, for a grade of $2.32 per ton. From 1,064,477 tons mined during the past two years, however, the yield has been only $1,389,607.03, or $1.41 per ton (gold at $20.67). Present output is at the rate of about 1,470 tons. per day. THE ORE-BODY AND WALL-ROCK: The Howey ore-body is part of a quartz porphyry dyke, which has. intruded an area of greenstone. The dyke strikes north 65° east, and its dip varies from 85° to the south at the surface to practically vertical below the. 1,000-foot horizon. Both along the strike and on the dip, the width of the dyke varies from 25 to 200 feet, the widest portion occurring below the 1,000-foot level. To the east of the ore-body, the dyke increases in width and finally splits into tongues of porphyry enclosed in greenstone, diorite, and congloJ11erate. To the west, it passes into the adjoining property, its width at the boundary being 100 feet. The rock in the ore-body is hard to drill, but, because of numerous horizontal slip-planes, it breaks well when blasted. This characteristic makes it possible to break large breasts or benches with a relatively small number of holes. The ore broken in this manner is consequently quite coarse, a large part of it requiring secondary breaking.

Jan 1, 1938

By Stuart Buckley

THE application of hydrocarbon equilibrium data to various problems encountered in refining and in natural gasoline recovery is an old and well established practice. Both generalized data and data on specific hydro-carbon systems have been made available by a number of investigators. More recently such data have been applied to the relations governing the separation of oil and gas both in the reservoir and at the surface. Most of the applications to production problems, however, have been based upon examinations of surface samples of oil and gas. This paper describes a technique that has been used satisfactorily in a number of cases to calculate directly from the hydrocarbon analysis of and auxiliary laboratory data on a subsurface sample of the reservoir fluid the behavior of the oil and gas during the various stages of separation at the surface incident to production.

Jan 1, 1938

By Oliver C. Ralston

[This paper is an expanded revision of a report entitled "Froth Flotation and Agglomerate Tabling of Nonmetallic Minerals, " published in Transactions of the Canadian Institute of Mining and Metallurgy (vol. 40, November 1937, pp- 691-726) and prepared a year previously. Revisions embodied herein brine the data up to January 1, 1938. References have also been added to make the earlier paper more complete for the period it covered.]

Jan 1, 1938

By Gregory J. Comstock

THERE is a growing interest in the possibilities presented by the manipulation of metal powders, which justifies an attempt to summarize their character and potential value. A summary of this kind presents an opportunity for making a classification of metal powder products into several general types. Our present knowledge of the finer and more abstract aspects of many of the principles involved in metal powder technique is extremely limited. Any conclusions as to the ultimate value of the process will, therefore, for the present at least, be of doubtful value unless they are substantiated by its products. The number of such products is increasing. A study of their diverse and unusual characteristics; an examination of the methods by which they are made, and a consideration of the reactions that take place during their fabrication, in so far as we can define them, should afford as good an evaluation of this interesting development as it is possible to make at this time. A critical study of this kind results in a formidable list of special attributes, which apparently ate characteristic of applied powder metallurgy. A comparison of these special effects with the end products and well defined limitations of the melting and casting process indicate that often they may very well be considered as being special advantages. They are subject, of course, to certain not as yet so well defined limitations of their own. Based on current products only, a necessarily condensed summary of the more striking special attributes of the metal powder process follows. MANIPULATION OF HIGHLY REFRACTORY METALS The powder process presents a means of manipulating highly refractory metals, which cannot be cast and formed in the usual melting and casting process. Tungsten, molybdenum and tantalum are the classic examples of the adequacy of the metal powder process for meeting unusual conditions of this character. The development and application of these metals by means of it, and their importance in the electrical

Jan 1, 1938

By C. E. Agnew

THE Eastern district, composed of New Jersey and eastern Pennsyl-vania, with its native ores, was the cradle of the iron industry of the United States. The district attained and held the leadership in produc-tion of pig iron for over 100 years, from pre-Revolutionary days to approximately 1875. The first shipment of Lake hematite ore was made in 1853. It was a small shipment, transported by a sailing vessel and a canal barge, but it was the beginning of the end of the supremacy of the Eastern district, although at that time the ore was supposed to be too rich to be successfully smelted with the block coal then in use at western furnaces. The iron made from the first shipment of Lake ore was worked into nails by the Sharon Iron Co., at Sharon, Pa. The writer's great-grandfather, David Agnew, and his brother, John P., Agnew, owners and-operators of the Sharpsville furnace, Sharpsville, Pa., worked the shipment through a furnace. Because of this, the writer feels some satisfaction in having been one of a group that solved the problem of making profitable an operation using Eastern district ores exclusively. With the development of Lake mines, and the production and use of coke, the Middle West district gradually assumed the position of leader-ship in production; because, even though the ores were transported 1000 miles by water and rail, its cost figure on pig iron was better than that of the eastern producer whose furnace was next to his mine. Such a cost figure was possible because the ore was naturally rich in iron and reduced easily. It was possible to carry a heavy burden on the furnace, which resulted in large tonnage and low coke per ton of iron. This paper is in no sense a technical one. The purpose is to show that with the proper physical preparation of the Eastern magnetites they will reduce as easily as the Lake hematites, and because of the high iron concentration give the Eastern producer just as much advantage as formally he was at a disadvantage in comparison with the Middle West producer.

Jan 1, 1938

By Joe H. Skidmore

This paper, describing mining and milling methods and costs at the Gold Hill mine, is one of a series being published by the Bureau of Mines. Boise Basin, in which the geld Hill mine is located, is in the central part of Boise County, Idaho, about 30 miles by air line northeast of Boise. The mine, owned and operated by Talache Mines, Inc., is at the southern end of the town of Quartzburg. About 115 to 125 tons daily is mind by square-setting and is treated in an amalgamation plant.

Jan 1, 1938

By K. C. McCutcheson

To a very large extent the quality of a mild steel ingot is determined by the manner in which it is poured into the ingot mold and its behavior during the first few minutes after it has been poured. The formation of the solid rim of metal around the periphery of the mold, the effervescent action of the liquid steel within this solidified rim and the upward or downward movement of the metal level are indications of what is going on beneath the surface of the liquid metal, especially at the interface at which solidification occurs. Observation of this "rimming action" enables an experienced observer to predict the thickness of the sound skin of the ingot and the location and extent of cavities or "blowholes" caused by entrapment of gases. The control of rimming action at the hands of a skillful steel pourer is a vital part of the control of quality in mild steel sheet, and the behavior of the liquid steel during the rimming period is a useful criterion of the melting and refining practices employed in the open hearth. The behavior of rimming steel during solidification depends primarily upon the evolution of gases from the molten metal and it is therefore a problem of considerable interest to determine the nature and amount of the gases evolved. A number of attempts to determine either the amount or the analysis of the, evolved gases have been reported. Klinger,1 in 1925, analyzed the gases extracted from rimming, semikilled and killed steel ingots and found that the chief constituent of the rimming gas was carbon monoxide. The relatively large amounts of nitrogen reported in his first few samples may have been due to incomplete removal of air from the gas-collecting mechanism. McKune2 reported similar studies of rimming ingots from which surprisingly large proportions of nitrogen and hydrogen were evolved. Ameen and Willners3 determined both the amount and composition of gases extracted from unkilled ingots with the aid of diminished pressure. Their ingots weighed only 80 kg. (176 lb.) and apparently were solid within two or three. minutes, so that their

Jan 1, 1938

By D. S. Reynolds, K. D. Jacob, H. L. Marshall

All types of commercial phosphate rock produced throughout the world contain fluorine in quantities ranging from approximately 0.4 to 1.3 per cent in the Curacao and Christmas Island phosphates to 3.1 to 4.2 per cent in the phosphates of the United States and North Africa1. For a given type of rock, the fluorine content is usually roughly proportional to the phosphorus content. Significance of Fluorine in Phosphate Rock On the basis of chemical and X-ray diffraction studies, Hendricks and co-workers2 concluded that fluorapatite, Cal10F2(PO4)6, is the essential phosphatic constituent of the commercial types of domestic phosphate rock. On the other hand, Bredig and co-workers3 have recently advanced the opinion, also based on X-ray diffraction studies, that the mineral phosphates usually contain carbon dioxide in the apatite lattice, and that the phosphate rocks of the United States are really fluorcarbonate apatites. However, the domestic types of phosphate rock do not seem to differ greatly from coarsely crystalline fluorapatite in their behavior toward chemical reagents in general, and for the purpose of this paper it will suffice to consider fluorapatite as being the essential phosphatic constituent of these types of rock. The available data1 indicate that the different commercial types of domestic phosphate rock usually contain about 12 to 52 per cent more fluorine than theoretically is required to form fluorapatite with all the phosphorus. Calcium fluoride (fluorite) has been definitely identified in only a very few of the samples that have been examined1,2. Bredig and co-workers4 state that fluorapatite can take into its crystal lattice excess calcium fluoride to the extent of approximately 70 per cent of that theoretically required by the formula Ca10F²(PO4)6 without causing more

Jan 1, 1938

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsater-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig. Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this typo of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938

By M. K. Senicie

IN July, 1937, Asbestos Corporation, Limited, installed an automatic conveyor-belt scale at their King mine, Thetford Mines. The equipment was purchased 'on trial' and its performance has proved entirely satisfactory to the staff. The scale was manufactured by the Toledo Scale Company, of Toledo (Ohio) and Windsor (Ont.) and was installed by one of the Scale Company's engineers. The electrical recording equipment was installed by Keith Mercer, Reg'd, of Montreal, Canadian agents for the manufacturers, the Builders Iron Foundry, of Providence, Rhode Island. The recording equipment consists of a duplex weight-transmitter attached to the scale-head, a duplex totalizer with differential relays, a belt-speed compensator, a rate-of-delivery recorder, and a rate-of-delivery indicator. As it was desired to run the mill at maximum capacity, it was necessary to know the rate of feed at all times, so that any lessening of rate of feed or delays would be recorded and could be corrected. After having determined the rate of feed to the mill (100 per cent capacity), it was required to have weighing and recording instruments which would show: (1) The rate of feed per hour. (2) Any variations .in the load. (3) Any delays and the duration and time of the delays. Rate of tonnage recorders in the mill superintendent's office and at the point of feedi.ng were necessary, as was automatic control between the mill superintendent and the feed man. It was desired to have a permanent record of total tonnage fed per shift or day; weighing and recording mechanism had to have sensitivity to record all previously mentioned conditions. Mechanism had to be of rugged construction, and be so built that it would stay in good operating condition, with the minimum amount of adjustment and supervision.

Jan 1, 1938

By Ralph H. Sweetser

At the joint session of Blast Furnace and Open Hearth Committees, April 7, 1937, at Birmingham, the subject of the quality of basic open-hearth pig iron was so well presented and discussed from so many different viewpoints that it was the general opinion that progress had been made and that such meetings were conducive to the advancement of the art of making pig iron of the right quality for the open-hearth man to produce the most satisfactory quality of steel. It was agreed that there is a decided differentiation between the chemical analysis of pig iron and the "quality" of pig iron. Paul J. McKim said that open-hearth furnace operators frequently make reference to certain types of iron as "bad iron," "dirty iron," "cold metal," etc., claiming that when using these irons, although they are within specified chemical analysis, it is impossible to produce quality steel. Mr. McKim gave a list of the suggested causes of those "certain types" of bad irons that have a thoroughly respectable analysis but a thoroughly disreputable character. Another open-hearth man, P. A. MacIsaac, of Nova Scotia, said that: The effects of iron that is below standard in analysis or in that mysterious property called quality, are well known to all open-hearth operators. It has been shown that iron of this type results in the production of steels on which the rcjections of finished product run high. What is to be done about it? I would say that the burden of producing high-quality iron should be placed squarely on the shoulders of the blastfurnace man, even as that of making good steel is shouldered by the open-hearth man. It is the purpose of this paper to bring out into the open this "mysterious property called quality"; that is, in those "certain types" of basic pig iron that make it impossible to produce quality steels; and at the same time to point the way for the blast-furnace man to be able to shoulder the burden that Mr. MacIsaac and all other open-hearth men and foundry-men have placed upon him. Silicon, sulphur, phosphorus and manganese are not the guilty elements because these are known, specified and usually kept within the

Jan 1, 1938

By M. W. Von Bernewitz

Fay's glossary3/ of terms contains the following definition of "black sand": Heavy grains of various minerals which have a dark color and. are usually found accompanying gold in alluvial deposits, for example, magnetite, chromite, ilmenite, cassiterite, tourmaline, and others. The Bureau of Mines is issuing this report in answer to the many inquiries from individuals and firms as to how they may treat or sell the heavy black sands that accumulate in the sluice boxes of beach and river placering and to warn such individuals and firms against becoming too enthusiastic over the chances of striking it rich. For a half century or longer much money, energy, and time have been wasted in devising, building, and trying numerous machines to recover gold and platinum, also gem stones, from sand that generally has not been worth the effort. Volumes have been written on the subject, and thousands of letters of inquiry have been received by agencies of the State and Federal Governments. The demand for information has been so great that all of the Bureau's publications dealing wholly or partly with black sands are out of print. They are listed at the end of this report.

Jan 1, 1938

By William W. Adams

The stone-quarrying and related industries of the United States made large gains in employment in 1936 over 1935, according to reports furnished by operating companies to the Bureau of Mines, United States Department of the Interior. Not only were more men employed, but also increases were made in the number of man-days of labor performed and in the number of man-hours worked in 1936. The increase in employment, however, was accompanied by an increase in the number of accidental deaths and injuries among the workers and by a slight increase in the accident-frequency rate per million man-hours worked. The fact that the larger number of accidents resulted in only a slight increase in the accident rate is explained by the large gain made in the number of man-hours worked during 1936. The accident rate in 1936, although higher than in 1935, was the lowest and therefore the best that the industry has experienced in any previous year except 1932 since complete and comparable figures first became available in 1916, a period of 21 years. Operators' reports to the Bureau of Mines showed that the industry as a whole employed an average of 80,022 men in 1936 and that the men worked a total of 18,874,254 man-days or 147,064,448 man-hours. Accidents in and about the plants caused 91 deaths and 5,717 nonfatal lost-time injuries among the workers. The number of injuries and deaths represented an accident-frequency rate of 39.5 per million man-hours worked, compared with a rate of 38.2 in 1935.

Jan 1, 1938

By Charles N. Becker

The practice of drying phosphate in Florida is as old as the industry, which began a little more than half a century ago. The methods, however, have changed considerably. At first, the natural process of exposure to the sun and air was used, later supplemented by wood fires beneath open-air stationary dry kilns and drying towers of various designs. It was not until the early nineties that rotary driers came into use, and at first they were of very small design and fired with wood. As the industry grew and tonnage increased, so likewise grew the number and size of rotary driers, until today the largest installations are 6 ft. up to 7 ft. 6 in. in diameter, and 55 to 60 ft. long, fired with crude oil. The reasons for drying phosphate rock are: (1) to eliminate freight on water in the shipment and (2) to facilitate the good grinding qualities required by the buyers in their acidulation. Phosphate pebbles vary materially in natural characteristics and each property has a direct bearing on the processing. In making comparisons of cost and operating conditions, the following are usually taken into consideration: 1. The hard dense pebbles, which contain very little interior moisture and 6 to 8 per cent total moisture, usually produced from the low-grade deposits. 2. The lighter, porous pebbles, which contain 4 to 5 per cent interior moisture and a total moisture ranging from 9 to 15 per cent. 3. The product of recovery operations using oily reagents, containing from 15 to 25 per cent moisture. 4. The size of the pebbles Usually the plus 5-mesh material is considered as "coarse rock"; the minus 5-mesh plus 24-mesh is "fine rock," and the minute particles below 24 mesh are called "concentrate." 5. The amount of moisture allowed in the dried product. The practice is generally to dry down to 1.5 to 2 per cent moisture. There is, however, an actual range in guarantee of from 1 per cent maximum to 3 per cent maximum.

Jan 1, 1938

By Henry Emmett Gross, David R. Mitchell, H. E. Oehler

THE production of fluorspar is one of the smaller nonmetallic industries in the United States with a capital investment-about $10,000,000. Shipments from United States mines' in 1936 totaled 176,231 short tons valued at $3,111,268, an average price of $17.65 per ton. The United States produces about 40 per cent of the world's fluorspar, of which about 90 per cent comes from the Illinois and Kentucky deposits along the Ohio River.2 Further detailed information on the fluorspar industry in the United States is given by Hatmaker and Davis.28 Fluorspar is marketed according to the following relative quantities and specifications : [ ] The concentration of the coarser sizes presents relatively little difficulty, good recoveries being obtained with jigs and tables. However, sizes smaller than about 10 mesh cannot be successfully treated by ordinary gravity separation methods and so have been accumulating as

Jan 1, 1938

[ ]

Jan 1, 1938

By Marvin J. Udy

THE preparation of this paper is in response to many requests for in-formation on the mining and smelting developments which have been carried on for the past three years or more by the Chromium Mining and Smelting Corporation of Canada. By way of introduction, the following paragraphs, relating to the early history and present status of the chrome-mining industry in the United States, are of interest. They are quoted from Bulletin No. 76 of the California State Mining Bureau, published in August, 1918: 'Chromium was discovered about 1797 by a French chemist, Louis Nicolaus Vauquelin, in ore from Siberia. From that time until 1827, the Urals, in the region of Ekaterinburg, supplied the chromium used in . Europe. In the summer of 1827, as the historian advises us, Isaac Tyson, Jr., saw in a Baltimore market-place a cart containing a cider barrel, which was held from rolling about by some heavy black stones. He had made a study of such stones at the first-known American locality, the Bare hills near his father's home, six miles from Baltimore, and he recognized the black stones as chromite. On inquiry, he found the chromite came from the Reed farm in Harford county, 27 miles northeast of Baltimore. At this time, Tyson was one of the very few men in the country who knew the value of chromite, and in the next few years he took full advantage of this knowledge. He immediately bought the Reed farm. He found about 30 tons of float-ore on the surface, but there was no outcrop of ore in place. Never-theless, he sank a shaft, and at a depth of eight feet struck an ore-pocket which proved to be 80 ft. long, 25 ft. wide, and 8 ft. in maximum thickness. His next discovery was of placer chromite in the sands in the beds of brooks on an estate called Soldiers' Delight, 16 miles northwest of Baltimore. Thus far, Tyson's observations had shown him that chromite occurred apparently only in serpentine areas. His explorations were now leading him farther afield. In 1828, he found on the Wood Farm, in Lancaster county, Pennsylvania, a deposit of float chromite which led him to lease the ore-right of the farm, which he finally purChased in 1832. Here he developed the famous Wood mine, the largest single producer of chromite in the world.

Jan 1, 1938

By Phillip B. Bucky, R. S. Taborelli

The term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater inechanization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar inodel built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimenbions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein. Longwall Mining What Is Longwall Mining?—Agreement should be reached as to what constitutes longwall mining and therefore what constitutes a longwall face. Let longwall mining be defined as the mining procedure in which the roof and overlying bed breaks tend to parallel the working face. In the ordinary stope or room-and-pillar mining the roof breaks tend to

Jan 1, 1938

By L. L. Swift

AT the present time there are four base metals being used for automo-tive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows in some types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and pre-venting overheating and rapid wear of parts. Less plasticity is required in a bearing metal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coeffi-cient of friction. Under most operating conditions the friction depends on the unit pressure of the bearing, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the bearing.1 The hardness of the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measure-ment of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual constituents was developed to fill this need.

Jan 1, 1938