Search Documents

By E. J. Gleim

In April 1932, the Bureau of Mines published Information Circular 6595, entitled "Data in Reference to Installation of Cables in Shafts and Boreholes", in which were described methods followed in various sections of the United States when electrical circuits are taken into mines by means of cables suspended in shafts and boreholes. In view of the present tendency to extend high-tension cables along entries and passageways from the bottom of the shaft, borehole, or other point of entrance to coal mines rather than over the surface, it is deemed that the various methods of installing such cables deserve careful consideration, particularly in mines in which gas and coal dust contribute to explosion hazards. This is especially true of localities where there is an inclination to restrict the extension of 2,300- and 4,000-volt circuits into the mines. Probably it is feared that accidental contact with the cables of such circuits may result in more serious shock than with lower voltages; also, it is possible that new circuits are regarded merely as explosion hazards additional to those already existing, regardless of the manner in which the new circuits may be installed. It is the firm belief of some engineers that the circuits can be installed so that they will not be damaged by wrecks or roof falls, thereby eliminating the hazard of explosion from this source while at the same time making the chance of accidental contact remote if not impossible. Moreover, some believe that fire hazards from direct-current systems can be reduced by keeping motor-generator sets close to load centers. Thus, although the alternating-current circuits would be lengthened, the size and extent of direct-current circuits would be kept to a minimum.

Jan 1, 1939

By Arthur Wade

During the year 1938, there was some drilling in Queensland, New South Wales and Victoria, as follows: Queens1and.—At Hutton Creek, lat. (approx.) 25° 45' S.; long (approx.) 149°, drilling was done by Drillers limited (subsidiary Oil Search) to a depth of 4688 ft., to the Lower Permian(?). There were small gas showings. The hole mas abandoned. At Mt. Bassett, lat (approx.) 26" 20' S.; long. (approx.) 149", Roma Blocks Oil Co. No Liability drilled to a depth of 4033 ft. The hole bottomed in granite. There were small showings of' oil and gas above bedrock in what may be Permian but is not yet determined. The company intends to run a formation tester. New South Wales.—At Kulnura, lat. (approx.) 33" S., long (approx.) 151°, the Kamilaroi Oil Company Ltd. (subsidiary of Oil Search Ltd.) drilled to a depth of 6293 ft. The Permian, probably Upper Marine Series, was reached. Drilling is to continue. Victoria.—At Romawi, lat. (approx) 37" 50' S., long. (approx.) 147" 45', a dry hole 3246 ft. deep bottomed in the Jurassic and was abandoned. It was drilled by the Governments of the Commonwealth and the State of Victoria. At Lakes Entrance, 1st. (approx.) 37" 50' S.; long. (approx) 748", a small showing of' oil (a few pints a day) was obtained from a well drilled 1275 It., to the Upper Oligocene-Glaucnnitc series, by the Austral Oil Drilling Syndicate, No Liability. Future Drilling Preparations is are being made by companies fur further test drilling in 1939, and the Governments of the Common wealth and the State of Victoria are continuing test holes for information only in the Gippsland district of Victoria. In Papua and New Guinea, no test drilling was done in 1938, but several companies are carrying on geological investigation and it is expected that, some test holes will be drilled during 1939.

Jan 1, 1939

By Ernest Kirkendall

The amount of research done in the last fen years on the subject of diffusion in solid metals is significant of the importance of this problem. To review the literature dealing with diffusion is unnecessary here. Deschl in 1912 reviewed the work that had been done on diffusion in solids and gave a bibliography of the literature published before that time. Mehl's paper in 19362 is an excellent review of diffusion in metals and contains a large bibliography. Of importance also for it? review and bibliography is an article by 14. I. Krynitsky.~ While considerable material lias appeared in the literature on diffusion in brass, the amount of information is not great compared to that pertaining to some of the other alloys. Most of the information published is of a qualitative nature; that which is quantitative varies considerably. Thus the quantitative determination of the rates of diffusion of copper and zinc in alpha brass by a new method appeared worth while. In the present investigation the rate of diffusion of zinc in approximately the same composition alpha brass has been determined :it three temperatures. Procedure The method used consisted of plating copper on a beta brass, heating it, to allow diffusion to take place, and measuring the concentration of copper by determining the lattice constant of the alloy. This method is unique in that it uses a beta brass of such a composition that at the tem perature at which diffusion takes place the beta brass is saturated wit11 copper. Thus, while the beta brass supplies thc zinc, no diffusion takes

Jan 1, 1939

By Frank C. Greene

The results of drilling in Missouri in 1938 are overshadowed by the leasing activity in northern Missouri, which began about the middle of the year. Nothing like it has ever been witnessed by the oil industry. With no production except a minor amount of gas, and with no drilling except in Clay, Platte and Marion Counties, a leasing campaign has embraced most of the counties north of the Missouri River and spread into southern Iowa, southeastern Nebraska and northeastern Kansas. It is reported that nearly all farms that could be leased without payment of a bonus have been leased, mostly on 10-yr. contracts, and at the end of the year a policy of bonus paying is in effect. Many of the major oil companies are leasing in the area and at least 15 of them are represented by scouts. Similarity to the Illinois Basin, low-priced leases and low drilling costs are among the reasons advanced for the leasing activity. Drilling activity in Missouri increased nearly two-thirds over 1937, with a total of 164 completions. The main activity was the extension of the "shoestring" of the so-called Bartlesville gas pool in Jackson County. It now seems that this sand is probably at the horizon of the Burbank sand. A new Squirrel sand oil pool was discovered in Jackson County. Cass County had five oil wells, with 63 bbl. initial production, four gas wells with 542,000 cu. ft. initial open flow, and 15 dry holes. Jackson County had three oil wells, with 24 bbl. initial production, 56 gas wells with 52,021,168 cu. ft. initial open flow and 57 dry holes. In Vernon County seven oil wells, with about 36 bbl. initial production, and two dry holes were completed. The oil production dropped off very quickly. In counties where wildcatting was carried on, new production was found. Clay County had seven dry holes, Hickory and Marion one each; Platte, four and St. Clair, two.

Jan 1, 1939

By Holbrook Botset

EXPERIMENTS performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This con-clusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely con-solidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be intro-duced was the cementing material.

Jan 1, 1939

By L. R. Burdick

This paper presents a review of published investigation dealing with the importance of sulfur compounds in the deterioration of materials or providing some basis for estimating the extent of loss shareable to such air pollution. Materials included are cement, stone, metals, paint, leather, paper, sand cloth. The investigations may be divided into two classes, one of the laboratory type in which the sulfur content and the humidity of the air were controlled and the other dealing with the exposure of materials to atmospheres not under control. The first type of work has shown that cement is subject to deterioration by the action of sulfur dioxide gas. The experiments with stone indicate that although limestone takes up sulfur dioxide, from the air, moist sulfur dioxide-air mixtures alone cannot be used for establishing- the comparative weathering- qualities of the different types of stone by accelerated test methods. Laboratory tests indicate that sulfur compounds in the air accelerate the corrosion of iron, steel, zinc, copper, and nickel at normal air temperatures and at certain relative humidities. It has also been indicated that certain types of paint are, affected by high sulfur dioxide concentrations, and that paper is attacked by sulfur dioxide in the atmosphere. The investigations of the second type show the amount or variation of corrosion in different localities and under different types of exposure. The investigations (10) (18)4/ during which sulfur determinations were made indicate that sulfur dioxide is a main controlling factor in the corrosion of iron and steel but according to Quick (18) may not be for some nonferrous metals. In general, the laboratory tests do not Jive definite data on the loss due to sulfur compounds at the concentrations normally found in the air. The data from atmospheric exposures are not complete from the standpoint of the exact effect of the sulfur compounds. Damage to materials so exposed is affected by factors such as other chemical contaminants, humidity, rainfall, solid deposits, and sunlight. A simple scheme has been devised in Great Britain which is considered to provide a measure of the attack of sulfur compound, on building materials (1). Small cylinders coated

Jan 1, 1939

By G. W. Jones

Fires in anthracite refuse banks are troublesome and may become exceedingly costly to combat. Instances are known in which refuse-bank fires have grown to such magnitude that entire mining properties have been endangered. In one instance4/ a refuse-bank fire cost the mine management several hundred thousand dollars to extinguish. The exact number of fires formerly existing or now active in the anthracite region of Pennsylvania is not known, There are hundreds of anthracite refuse banks in this region, some very high and large in area, that have never caught fire, although a few are over 50 years old. This would indicate that spontaneous ignition of the material in these banks is improbable, a conclusion confirmed by recent laboratory research.

Jan 1, 1939

By G. E. Steudel

THE study of the possibility of effecting a lower cost in the manu-facture of pig iron reveals the importance of the ever present question of slag chemistry and volume. Factors that determine slag chemistry and volume are the impurities in the ore available, the ash-sulphur content of the coke, and a flux material necessary to promote removal of sulphur. Of these, the ores present by far the major source of impurities and what may prove to be the lowest practical slag volume with desired chemistry in one locality may be considered low or high in some other center of iron manufacture. The Chicago district is not only blessed with ores of high quality, but with excellent coke and flux materials as well. It is the intent of this paper to discuss slag problems at the South Works only, where burdens consist of Mesabi ores, Michigan stone, and coke ranging from 7 to 9 per cent ash and containing an average of 0.57 per cent sulphur. Early in the development of modern blast-furnace practice, the con-sideration of slags was secondary to the many adjustments of mechanical difficulties, such as furnace lines, stock distribution, stove design for obtaining higher blast temperatures, improved chemical segregation and size of raw materials. Furnace operators, after making these improve-ments, turned their attention to the study of other refinements in practice, of which slag chemistry appeared to be the most important. It is only within the last two decades that operators have become familiar with the various aspects of slag compositions. The industry, while rather slow in its recognition, is indebted to such investigators as Rankin,1 Wright,1 Feild,2 Royster,2 McCaffery,3 Kinney,4 Holbrook,5 and Joseph5, whose researches concerning the elimination of sulphur within the blast furnace and the effect of slag composition upon melting point, viscosity, and desulphurizing power have established criteria for the selection of slags of the requisite quality.

Jan 1, 1939

By C. W. Mason

TIN has long been cited as offering a classic example of polymorphism, second in repute only to the allotropy of sulphur. The notorious "tin disease," which Cohen1 has studied so exhaustively in terms of the enantiotropic transformation of tetragonal white 0 tin to cubic gray a tin, has apparently encouraged the expectation that one or more addi-tional polymorphic modifications might exist. The search for confirma-tion of this idea has, as might be anticipated, led to the accumulation of a body of miscellaneous evidence, much of which would probably never have been sought, or taken seriously even by its discoverers, but for previous assumptions. The ball apparently was started rolling in 1880 by Trechmann,' who reported a new modification of tin (y tin), which was brittle and found in "hard head," a highly arsenical, slaggy material produced in a certain stage of tin smelting. A mixture of two kinds of crystals was obtained from a Cornish tin furnace, and those thought to be y tin were studied crystallographically. The results indicated that these crystals were rhombic and of different density from the tetragonal tin prepared electrolytically by Miller.3 Their analysis was given as 98.7 per cent Sn, 1.3 per cent Fe, and traces of As, Sb, Bi and S. In 1881 von Foullon4 obtained similar crystals from a Bohemian tin furnace. Headden5 examined crystals similar to those of Trechmann and von Foullon and reported them to be monoclinic, but of analysis corresponding to stannous sulphide. Later, Stevanovic,6 by goniometric measurements, proved that these crystals of SnS were really rhombic. Groth7 pictures and describes both "rhombic tin" (Fig. 9, vol. 1) and stannous sulphide (Fig. 84, vol. 1); their faces and angles correspond within the accuracy of measurement. Spencer3 in 1921 examined the above evidence critically; he found similar crystals from Cornish tin furnaces, proved them to be SnS, and even was able to analyze some of Trechmann's original specimens, finding high sulphur content. (Apparently Trechmann's analysis had been based on a second lot of crystals, not described crystallographically.)

Jan 1, 1939

By Jos. R. Guiteras

This paper is one of o. series describing mining and milling methods and costs being published by the United States Bureau of Mines. It presents the results of a study of the Alice mine by the writer in December 1936. ACKNOWLEDGMENTS Acknowledgment is made to J. Fred Johnson, mining engineer off the American Smelting & Refining Co., for permission to visit the property; and to Arthur F. Johnson, general superintendent at the property, for his friendly cooperation in contributing the information contained in the paper.

Jan 1, 1939

By J. J. Jakosky

The fundamental hydrodynamic principles governing the production of oil from wells have been carefully studied and evaluated by many investigators. These prior studies are quite complete and cover virtually the entire field of oil production and recovery.' One of the most important measurements in production studies is that of the bottom-hole pressure at various rates of production.2 It is the purpose of this paper to outline the technique and economics of fluid-level measurements as applied to pumping wells and to review briefly other methods for obtaining bottom-hole data. The applications of bottom-hole pressure or fluid-level measurements are based on simple hydrodynamic principles. Under equilibrium conditions, pbh = hd + pg + pch [1] when pbk = bottom-hole pressure, Ib. per sq. in. absolute, h = height of fluid in well, ft., d = average fluid density, Ib. per sq. in. per foot, p, = weight of section of gas column 1 in, square from fluid level to casinghead, Pch = casinghead pressure, Ib. per sq. in. absolute. In words, equation 1 states that the bottom-hole pressure is equal to the weight hd of the column of fluid plus the weight of the column of gas between the fluid and the casinghead plus the casinghead pressure. At moderate rates of flow, the rate of production is approximatcly proportional to the difference between the reservoir, or static bottom-hole. pressure and the flowing or producing pressure; i.e.: Q = c(pr - pbh) [2] pr = the reservoir pressure, c = the constant of proportionality. However, at production rates approaching zero and also at high rates the proportionality may break down. By combining equations 1 and 2 the

Jan 1, 1939

By L. M. Barker

THE New Cornelia Branch of the Phelps Dodge Corporation is at Ajo, Pima County, Ariz. It is at the southern terminus of the Tucson, Cornelia and Gila Bend Railroad, which connects with the Southern Pacific Railroad at Gila Bend, Ariz., approximately 43 miles to the north. HISTORY Early history of the Ajo district has been related by A. W. Allen1 and by T. A. Rickard.2 Briefly, steps looking to the large-scale development of the ore body were instituted as early as 1912. This work culminated in the equipment of the property for open-pit mining by steam shovels. Ores initially mined carried economic amounts of copper carbonates as the principal copper-bearing mineral. Treatment methods developed for the extraction of the copper content involved leaching and a 5000-ton leaching plant was constructed and placed in operation in early 1917. Description of methods and equipment employed in this plant has been given by A. A. Tobelmann and James A. Potter.3 As exhaustion of the carbonate ore body neared, and mining oper-ations exposed an adequate tonnage of sulphide ores, a 5000-ton con-centrator was constructed for their treatment. That plant has been described by H. Kenyon Burch.4 Construction was completed and the plant was placed in operation in early 1924. Changes made in the original plant to improve practices and increase production will be the subject of subsequent paragraphs of this paper.

Jan 1, 1939

By Jacobsen L. K, Gross K. B

This paper, describing milling practice at Mount Isa Mines, is one of a series covering milling methods and costs that is being published by the Bureau of Mines, United States Department of the Interior.The Mount Isa concentrator began operations in May 1931, by treating a mixture of oxidized and sulphide ores. Since March, 1935, only sulphide ores have been milled; this change involved major alterations to the flow sheet. The maximum capacity on mixed oxide and sulphide ores was 2,650 tons per day; the present capacity is approximately 1,880 tons of sulphide ore per day. The installation of additional Grushing, grinding, and flotation equipment when completed early in 1939 will increase the maximum capacity of the concentrator to 2;240 tons of sulphide ore daily.All tonnages in this paper are expressed in tons of 2,000 pounds, gallon measurements in terms of Imperial gallons of 277·41 cubic inches, and costs in dollars at the rate of $4 United States currency to the Australian pound.

Jan 1, 1939

By R. V. Lukes, H. W. Scheeline

Knowledge of a large number of the physical properties of the hydrocarbons is needed in the calculations and studies of the production engineer. Since experimental data on these properties of the individual hydrocarbons and their mixtures are available in only a relatively few cases, the use of generalized correlations has developed rapidly in the last decade. The generalized correlations of pressure, volume and temperature,' enthalpy2 and vapor-liquid equilibria13 on the basis of reduced temperatures and pressures, are outstanding examples of this development. These correlations are of particular value to the production engineer interested in the flow of oil and gas, since they can be used to estimate the conditions under which segregation of phase occurs as well as the composition, density, and relative amounts of the phases. The technique of using the correlations for such estimations has been published by several authors4 and will not be considered in this paper. A considerable number of data have been obtained to check the generalized pressure-volume-temperature correlations, and these data indicate that such relations hold for the hydrocarbons from methane to heptane. The accuracy is in general sufficient for most engineering pressure-volume-temperature calculations. However, the generalized correlations of enthalpy and vapor-liquid equilibria have in general been developed from the pressure-volume-temperature correlations by thermodynamic calculations and only a relatively few experimental data are available to check these calculated values. The calculations from pressure, volume and temperature are likely to lead to large errors in the calculated enthalpy and vapor-liquid equilibria. Thus, in the calculations of enthalpies, slopes of the pressure-volume-temperature data are employed, and determining these slopes can greatly amplify small errors in the original data. In the vapor-liquid equilibria calculations it is necessary to have the pressure-volume-temperature relations of the mixture, and the latter propertics are much more questionable than those of pure components, particularly in the critical region. A considerable number of experimental data are

Jan 1, 1939

By V. J. Southey

HOLLINGER mining operations have required development by 24 vertical shafts having a total length of 28,160 feet. Seventeen of these are sunk from surface and seven are interior shafts. Four surface shafts and three interior shafts are now active and, excepting the recently completed new main ore-hoisting shaft, the remainder are either abandoned, or are used for passes or for ventilation. The new shaft bottoms 60 feet below the 3,050 level, but there is much work to be done before it is placed in service. The term 'shaft practice' is intended to include shaft construction and a general treatment o typical equipment. It is a large subject for an organization the size of Hollinger and this paper is intended only to present the salient features. The writer wishes to thank the management for permission to publish this information and to acknowledge the advice and criticism o A. G. Irving, chief engineer, and the willing co-operation of other members of the Hollinger staff.

Jan 1, 1939

By L. R. Burdick

Sulfur compounds have long been recognized as damaging pollutants of the air. A number of investigations have been made to determine the amount of such compounds existing in the air of various cities; moreover, some study has been given to the conditions affecting the concentrations. This paper summarizes published investigation and includes a bibliography on the subject. The methods of obtaining data have differed to the type of sampling, analysis procedure, hour of sampling, number of locations, and number of determinations made. Sampling methods include both the continuous type, covering a day or a number of days, and what can considered the ?snap? type, covering very short periods. Continuous sampling has, given data representing the average concentration at the location chosen but no information regarding variations from hour to hour, are none that might be said to represent the average for a city. The snap-sampling method, while not giving a true average for any one location or area, has in some instances made available date regarding variations of concentration during different hours of the day and at various locations or zones within the area chosen. Although the sulfur compounds in the air nay include sulfur dioxide, sulfur trioxide, hydrogen sulfide, and organic compounds of sulfur, most investigators report on the basis of sulfur dioxide. This gas unites with moisture to form sulfurous acid.

Jan 1, 1939

By Paul Weir

BLEACHING clays have been used extensively in the oil-refining industries for a number of years. Their use in water purification is relatively recent and less extensive. They are frequently classified as (1) those naturally active and (2) those active after artificial activation with acid. Fuller's earths fall within the general group of bleaching clays and gradually the commercial term "fuller's earth" has been applied to natural clays originating, for the most part, in the south- eastern section of the United States. Bentonitic clays are usually classed as activable and are prevalent in the southwestern section of the United States. Bleaching clays vary considerably in chemical and physical properties throughout the country, or even in different parts of one deposit (Table 1). [ ] The fuller's earth type of clay is characterized by a lack of plasticity, relatively adsorbent, foliated structure, and does not swell to form a

Jan 1, 1939

The Institute is custodian of funds for support of numerous gold medals and prizes and has representatives on boards awarding still others. Details regarding the Institute Awards are given below. The Institute is represented on the boards of the John Fritz Medal, the Hoover Medal and the Washington Award, in connection with the three national societies of Civil, Mechanical and Electrical engineering; and, also, in the case of the Washington Award, with the Western Society of Engineers. The Institute is represented with these four societies on the committee in charge of the Alfred Noble Prize.

Jan 1, 1939

By Joseph A. Holmes

Although Venezuelan production attained a new peak in 1938, passing the 190 million barrel mark for the first time, there was a distinct flattening of the steep upward trend that marked 1937 and preceding years. The annual total of 190,231,780 bbl. was only 31/3 million barrels above the 1937 figure, an increase of slightly less than 2 per cent, which contrasts sharply with the 20 per cent increase of 1937 over 1936. As in the previous year, the Lake Maracaibo fields supplied approximately 73 per cent of the oil produced, Lagunillas remaining the largest single contributor in spite of a 17 million barrel decrease in its annual output. Tia Juana increased its percentage of the Venezuelan total from 14.1 per cent in 1937 to 23.4 per cent in 1938; La Rosa showed little change with 13.7 per cent; Quiriquire in eastern Venezuela was also little changed with 13.2 per cent; Mene Grande, the only other field of real importance, declined from 7.7 per cent of the total in 1937 to 6.6 per cent for 1938. Two new fields, Temblador and Bachaquero, began actively to ship oil during the year, and by November were averaging 7600 and 10,000 bbl. per day, respectively. The former is in eastern Venezuela, and the latter is the most southern of the proven Lake Maracaibo fields. (A map of Venezuela was published in Volume 127 of the Transactions.) Table 1 gives a complete résumé of Venezuelan production by fields for 1937 and 1938, and shows that 1,685,575,663 bbl. had been produced to Dec. 31, 1938. The percentage contributed by each of the principal fields to this total is shown in Table 3, as well as their trends over the past several years. From these data it is apparent that the Maracaibo Basin is the principal source of Venezuelan production, and will probably continue to hold this position for some years. At the year's end 2657 oil wells were producing, of which 2425 were in western and 232 in eastern Venezuela; 36 per cent were on natural flow, 57 ppr cent were pumping, and 7 per cent were on air or gas lift. Out of 523 wells drilled, 507 producers were completed in 1938, five less than in the previous year and nearly 100 less than in 1929. These

Jan 1, 1939

By David P. Hale, Guy W. Jordan

HIGH-IRON cements have a number of advantages over cements carrying little or no iron. The presence of iron in Portland cement aids in the manufacture of the cement and also imparts certain advantageous physical properties to the finished product. In manufacture, the presence of iron lowers the fuel consumption, increases the ease of proper burning, and lessens the destructive action of the charge on the kiln refractories. In the finished cement the presence of iron reduces the expansion and contraction, adds strength, adds increased resistance to freezing and thawing, and increases the resistance of the cement to sea or sulphate waters. During the past few years the construction of numerous dams throughout the Southeast by the Tennessee Valley Authority has stimulated the production of high-iron cements. At present a great number of specifications call for an iron cement, and the industry is supplying this demand with a Portland cement carrying approximately 5 per cent iron oxide. Several manufacturers are now making practically all of their cement of this type and a number of others manufacture it as a special cement over short periods to meet demands from the Tennessee Valley Authority and other buyers. The recent increase in the use of iron in Portland cement has created a market for iron products that previously was nonexistent. The chief sources of supply for the cement manufacturers at present are iron sand, iron sinter and slag, and ocher. The Copperhill mining district, Tennessee, supplies both iron sinter and slag for use in cement. The Cartersville district supplies iron sand, ocher, and some iron resulting from the magnetic separation of iron from barite. The advantages of these products vary according to the chemical properties of the raw materials and the methods of handling used by the different manufacturers. Where the iron is to be handled by conveying belts and in hopper cars, the iron

Jan 1, 1939