Search Documents

By Hermann Schmalzried, Carl Wagner

UPON heating a metal oxide or sulfide in H2, first only oxygen or sulfur is removed from the surface. Thus the metal/nonmetal ratio in the oxide or sulfide increases and the thermodynamic activity of the metal increases accordingly. For the formation of metallic nuclei, a certain super saturation is necessary, i.e., the activity of the metal must become greater than unity. Once nuclei of the metal have been formed, the supersaturation is supposed to decrease. Even under steady-state conditions of a reduction process, however, the activity of the metal inside an oxide or sulfide phase must be greater than unity in order to have a driving force for the individual steps of the reduction process. As an example, consider the reduction of Ag2S with a high mobility of cations and electrons. As shown schematically in Fig. 1, the reduction process involves the following steps:' 1) sulfur removal along the entire Ag2S surface in form of H2S, 2) migration of Ag' ions and electrons from the Ag2S surface to nuclei of metallic silver, 3) transfer of Ag+ ions and electrons from the Ag2S phase to the metal. For a finite rate of step 3, the activity of silver in Ag2S next to the Ag2S-Ag interface must be greater than unity. Moreover, for a finite rate of step 2, the activity of silver at the gas-Ag2S interface must be still somewhat greater. Theoretical considerations lead to the tentative conclusion that at least under steady-state conditions the supersaturation will be rather low.' To test this conclusion, the average activity aAg of silver in a Ag2S tablet about 2 mm thick with a diameter of 5 mm was followed as a function of time by measuring the electromotive force E of the cell Pt I Ag | Agl I Ag2S I Pt where AgI is used as a solid electrolyte in which only Ag+ ions are mobile. The activity aAg is calculated as aAg=exp(-EF/RT) Since the diffusion coefficient for transport of silver in Ag2S is very high (- 3 . l0-2 sq cm per sec),3 the average activity aAg is representative for both the bulk and the surface of the Ag2S tablet. Experiments were conducted at about 400°C. The cell was surrounded by an aluminum block in order to secure a uniform temperature and to eliminate thermoelectric effects. With the help of a potentiometer, first a potential of 0.16 v was applied to the above cell in argon in order to obtain a well defined initial state with a Ag/S ratio close to 2.000.~ Then the cell was disconnected from the potentiometer and a gentle stream of H2 was passed along the Ag2S surface. In view of the removal of sulfur in form of H2S, the electromotive force E decreased within 20 to 30 min to zero corresponding to a Ag/S ratio of 2.003 and became negative, indicating a value of aAg> 1. A representative plot electromotive force E vs time is shown in Fig. 2. The minimum of the electromotive force characteristic of the onset of

Jan 1, 1963

By J. Rourke, F. S. Minshall, E. G. Zukas, C. M. Fowler, O&apos

The Hugoniot curves were determined for Fe-Si alloys containing up to 7 wt pct (13 at. pct) Si. The pressure of the transition increased as the silicon content of the alloy increased. Single crystals of 2.9 wt pct Si-Fe were also studied. The pressure of the transition was not dependent on crystallo-graphic orientation. All of the Neumann bands (mechanical twins) were attributable to (112) planes but not all of the {112} planes showed twin markings. A thorough study of the iron Hugoniot (the relationship between specific volume and pressure) under plane wave shock loading revealed a pressure transition at about 130 kbar shock pressure. The results of this investigation were reported by Bancroft, Peterson, and inshall1 in 1956. At the time of this discovery, it was felt that this was probably the a, to y transition normally found in iron and many of its alloys. Subsequently a number of iron alloy systems were surveyed in which the alloying element has a considerable effect on the normal a, to y transformation. The influence of carbon and nickel and/or chromium have already been reported.2,3 At the present time, there appears to be some doubt that this pressure transition is the usual a, to y transition In this study, Fe-Si alloys containing up to 7 wt pct (13 at. pct) Si were chosen for several reasons. To the present, the transition has been found only in iron-base alloys which were originally in the a, phase (bcc). Secondly, the y loop at atmospheric pressure extends to only about 2.5 wt pct Si. If the transition were a, to y, then one might expect a rather drastic pressure effect for alloys containing more than 2.5 wt pct Si. Finally, single crystals of Fe-Si alloys large enough for shock loading studies are readily available thereby making it quite easy to determine the effect of crystal orientation on the transition pressure and on the twinning behavior of the alloy. EXPERIMENTAL PROCEDURE Fe-Si alloys containing up to 7 wt pct Si were produced by normal vacuum casting procedures. Single crystals of Fe-2.9 wt pct Si were purchased from Monocrystals Co., Cleveland, Ohio. The orientations of these crystals were determined and samples cut so that the shock wave would be parallel (to within 1.5 deg) to either the (loo), (Ill), or (112) principal orientations. Three distinct experimental testing techniques were used. First, the pin technique, described elsewhere,4 was used to determine the transition pressure for the polycrystalline alloys as well as for the (111) and (112) orientations of the 2.9 wt pct Si single crystals. Secondly, the recovery studies, described in detail in an earlier paper,2 were used for determining the effect of alloy composition and crystal orientation on the plastic II compression-plastic I rarefaction interaction zone for several specific shock pressures. Finally, measurements of pressures above the two-wave threshold were made on the polycrystalline alloys so that more complete Hugoniot curves could be constructed for this alloy system. The optical techniques described by Rice et al.5 were used to measure the shock and free surface velocities of the samples from which the Hugoniot data were obtained. This method is applicable only in the single wave region, since velocities are obtained from the measured total transit times of the disturbances through measured sample thicknesses.

Jan 1, 1963

By S. J. Matas, R. F. Hehemann, R. H. Goodenow

The hot-stage metallographic method has been employed to determine radial growth rates of upper and lower bainite. Lower bainite appears to grow as individual plates that increase in both length and thickness while upper bainite grows as sheaves of closely spaced plates or needles. A discontinuity in the temperature dependence of the growth rate appears to be associated with the transition from upper to lower bainite and stepped quenching experiments suggest that lower bainite will not continue to grow when the temperature is raised to the upper range. Thus, a single process does not appear to control the growth of both upper and lower bainite. A tentative model based on the forces acting on a dislocation interface is proposed to account for the slow growth of bainite. It has been recognized since the early studies of Davenport and Bain that a close relationship exists between the martensite and bainite transformations in steels. However, diffusion of carbon during the transformation has lead to considerable controversy concerning the reaction mechanism.1-7 Many studies4,5,7-9 have emphasized the structura and kinetic aspects of the bainite reaction and, in particular, the difference observed between the two forms of bainite—frequently termed upper and lower bainite. A kinetic difference between the two types of bainite has been revealed in the activation energy determined from the overall reaction;4,5 however, many difficulties arise in an interpretation of these activation energies since a number of temperature dependent factors contribute to the kinetics of the overall reaction. The displacive surface relief10 accompanying the bainite reaction permits a separation of the nuclea-tion and growth contributions to the reaction and allows the kinetics of the growth process to be examined. Several investigations of this type have been conducted; however, they have been restricted to the low temperature range.3'6'11 Here, bainite plates are observed to grow slowly in both length and width. The present investigation extends such studies to include the upper bainite range. MATERIALS AND PROCEDURE Materials. The composition of the steels studied in this investigation are presented in Table I. The range of composition permitted a study of the effect of carbon content on the growth rate of upper bainite in the 9 pct Ni steels and consideration of both upper and lower bainite in the higher carbon steels. These steels were received as hot-rolled rounds and were forged to approximately 1/2 in. thick plates for preparation of metallographic specimens. In order to produce an essentially zero carbon steel, Steel A was decarburized in wet hydrogen at 1550°F for 15 days with the result tabulated as Steel AD. Experimental Procedure. In order to study the slow growth of the displacive transformation product, a commercially available Leitz hot stage was modified to permit heating of the specimen by its own resistance in a manner similar to that employed by other investigators.6 The furnace chamber was maintained at a pressure of 2 to 3 X 10-5 mm Hg prior to austenitizing at 2000° ± 12° F for 5 min. Samples could be cooled from the austenitizing to the transformation temperature in approximately 15 sec and the progress of transformation was recorded with a 9 cm by 12 cm single frame camera or a 16 mm movie camera. RESULTS AND DISCUSSION Growth Characteristics. The general growth characteristics observed in this investigation were analogous to those reported previously.3,6,11 Typical growth sequences for the high temperature and low temperature forms are illustrated in Figs. 1 to 5. In both temperature ranges, bainite plates increase in length at slow, temperature dependent rates until interrupted by a grain boundary, another plate, or

Jan 1, 1963

By F. W. Schaller

TETRAGONALITY is an important aspect of the models of transformation, strengthening, and tempering of ferrous martensite. When the c/a

Jan 1, 1963

By G. B. Hudson

Previous papers (1, 2) pertaining to the treatment of uranium-bearing ores were concerned with the flotation of the radioactive minerals. In this investigation, the application of flotation to the removal of acid-consuming minerals from uranium ores was considered. Two pitchblende-bearing ores, which, because of the presence if dolomite were abnormally high acid consumers, were studied. In both in-stances commercial reagents of widely varying fatty acid composition proved satisfactory as flotation col-lectors, particularly at a pH of 10.5, for the carbonate minerals. From an economic viewpoint, however, Neo-Fat 42-12 was favoured. A mixture of sodium tripolyphosphate and citric acid was an effective depressant for the pitchblende in the ores. The tailings remaining after the removal of the dolomite by flotation contained, in one case, 88.5 per cent of the uranium in the original sample, and, in the other, 93.8 per cent. Analyses conducted on these tailings and on the original ores showed that

Jan 1, 1963

By V. N. Cox, C. H. Grant

Both the underwater method and the rock cratering method contribute useful information in evaluating and comparing new explosive compositions. Results indicate that metallized explosive systems which contain no high explosives can be formulated to offer more energy and to do potentially more work than other slurry explosive systems. Commercial field trials are presently being conducted with a metallized explosive that does not contain any high explosive. Although there have been only a few commercial blasts to date, the results are encouraging. The Dow Chemical Co. has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which DOW is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of nonmetallized explosives currently being used. Early in 1960, additional patent rights were acquired from independent inventors and a development station at Virginia, Minn., was set up to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the boreholes. Due to the complexities involved in controlling the manufacture of the explosive in the borehole, performance was sometimes in doubt. Furthermore, experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over 2000 charges of 8 to 60 lb under water and in taconites and granites with many types of explosives, a metallized explosive was developed which is now being manufactured at a pilot plant in Virginia, Minn. and is being evaluated commercially. UNDERWATER METHOD An underwater method of evaluating explosives has a number of advantages. A permanent site can be established and operated indefinitely. A large number of charges may be fired in a short length of time. The medium in which the explosive is shot is exactly the same for successive shots. Data are recorded electronically minimizing human judgment. A disadvantage of the underwater method is the lack of confinement provided by the water medium. Many explosive compositions require a greater degree of confinement to develop good energy release. Although the relative significance of the two components of energy release that are usually measured, the shock energy and the bubble energy, and their relationship to breaking rock are not clearly understood, the underwater method is a valuable research tool for screening explosive compositions and gaining an insight into the manner in which explosives release their energy. Fig. 1 shows schematically the underwater apparatus. The piezoelectric gages are calibrated tourmaline crystals which convert the shock wave to an electrical impulse which is transmitted to an oscilloscope and recorded on Polaroid film. The shock traces are picked up by scopes 1 and 2. Scope 1 is timed to pick up the full trace whereas scope 2 is timed to cover the first increment of the shock trace expanded, and therefore allows full inspection of the propagation and peak pressures. Scope 3 records the bubble trace. When the explosion occurs, a bubble of gaseous detonation products is formed. The outward momentum of the water keeps expanding the bubble even after

Jan 1, 1963

By K. K. Kelley

The heats of formation of two lead vanadates (Pb2V207 and Pb3V208) and manganese vanadate (MnV206) were determined by hydrochloric acid solution calorimetry, supplementing previous Bureau of Mines measurements of the vanadates of calcium, magnesium} and sodium. Heat and free energy data for 11 vanadates were assembled on a common basis. The stability of comparable vanadates (with respect to the oxides) increases in the following order: Magnesium, manganese, lead, calcium, sodium.

Jan 1, 1963

By T. A. Henrie

A technique was devised for measuring the rate of chemical reactions between reactive metals and molten-salt mixtures at high temperatures. The rate of the heterogeneous reaction between high-purity titanium metal and titanium trichloride in molten sodium chloride was determined. The reaction is surface-controlled, and the heat of activation is 8.29 kilocalories per mole TiC13. An active site or reaction nuclei is created by adsorbing a TiC13 molecule at the metal surface. Reaction of the second TiC13 species forms an activated complex that decomposes into three TiC12 molecules.

Jan 1, 1963

By M. J. Kovalik

The effect of oxidation by air at temperatures ranging from 200° to 390° C on the change of chemical and physical properties of Pittsburgh-bed coal was studied as a function of processing time and temperature. The goal was to prepare a nonagglomerating fuel from a strongly coking coal for use in continuous carbonizing processes and in fixed-bed gasifiers. The oxidized coal was carbonized in a bench-scale apparatus, and the coke strength was evaluated in a Roga tumbler. Strength of the coke was progressively reduced with time of oxidation until the coking power of the coal was apparently destroyed. Time requirements to obtain an essentially nonagglomerating product were inversely related to processing temperature. Gaseous products released from the coal during oxidation reduced the yield of the desired nonagglomerating product, which decreased with time of oxidation at constant temperature and with increase in processing temperature at equal time. Oxidation at a temperature slightly above the lower limit of the plastic temperature range of Pittsburgh-bed coal was most effective because of the short processing time required and moderate processing losses.

Jan 1, 1963

The Burra Burra Aline is in complexly folded Torrensian dolomites and limestones forming the faulted axial region of a major anti cling. The orebody mined was largely of secondary origin and confined between two faults, Kingston's on the west and Tinline's on the east. The orebody occurred at the junction between cherty dolomites and a clastic limestone with a large mass of marble breccia along its western margin. Secondary ore consisted of carbonates and oxides in the breccia and the ore bed and detrital copper minerals deposited. As part of a clastic breccia in sink holes and solution cavities in the dolpthites and ore beds.Primary sulphides occur disseminated in the marble breccia and in stratiform habit in the ore bed. Kingston's so-called 'Lode' may be mineralised marble breccia.The marble breccia appears to be of diapric or sedimentary origin and there is evidence to support a sedimentary origin for some 'of the copper sulphides. No igneous rocks have been discovered within 20 miles of the mine and any hydrothermal activities were probably at comparatively low temperature. The possibility of extensive stratiform and disseminated copper sulphide mineralisation in the marble breccia and ore bed requires testing by further drilling and geophysicalsurveys.

Jan 1, 1963

By W. R. Hardwick

This paper describing the mining methods of the Inspiration Consolidated Copper Co. is one of a series being prepared by the Bureau of Mines on mining methods and costs in various mining districts of the United States. The story of mining at Inspiration is of particular interest because, after 127,812,000 tons of low-grade copper ore were successfully mined, the mining method was changed from block caving to open-pit. As the open pit became deeper, many features of the former block-caving operation that were exposed elucidated concepts of the mechanics of caving that previously had been assumed but not observed. The conversion to open-pit mining was accomplished by unique combinations of equipment and the introduction of ingenious engineering and operating practices that have extended the expected life of the mine for many years.

Jan 1, 1963

By Ruth F. Brinkley

Principle activities of the Bureau of Mines Explosives Research Laboratory from July 1, 1960 to June 30, 1961 are reviewed briefly in Part 1. Part 1 also includes data obtained in connect ion with several minor investigations which are not sufficient to warrant separate publications. Part 2 gives brief abstracts of publications that appeared during fiscal year 1961; in general, the research reported in these publications antedates this period.

Jan 1, 1963

By S. K. Tarby, W. O. Philbrook

Limited experimental data and a critical review of the literature are given to indicate that the true equilibrium distribution of manganese between carbon-saturated iron and blast-furnace type slags has not yet been satisfactorily established as a function of the composition, temperature, and pressure of the system. THE distribution of manganese between carbon-saturated iron and blast-furnace type slags has been studied by a number of investigators.1-7 Generalization of the results of these works indicates that the weight percent distribution ratio, (%Mno)/[%Mn], decreases with increasing temperature and slag basicity, in accord with thermodynamic data and practical observation. However, where comparisons among these studies can be made for similar slag compositions and temperatures, the reported values of the manganese distribution ratio are discordant. The variations are attributed to failure of the experimenters to bring their systems completely to equilibrium with graphite and CO at 1 atm, as judged by departures from silicon equilibrium. Even in the most recent work,5-7 this problem was recognized but the authors made the questionable assumption that equilibrium could prevail for manganese distribution even though other reactions were still in progress. Manganese equilibrium values for three particular slag compositions were required incidental to a kinetic study8 and were determined experimentally. Special pains were taken to approach concurrent equilibrium with respect to silicon. Although the results were not completely definitive, they indicate that the true manganese equilibrium distribution ratios are lower than have heretofore been reported. The data are presented together with a brief commentary on the literature to suggest the need for further work in this area. EXPERIMENTAL METHOD Equilibrium runs were carried out in a stationary, induction-heated graphite crucible closed by a graphite lid and flushed continuously by a slow flow of carbon monoxide at 1 atm pressure. Temperature was controlled manually within ±3 deg C with the aid of immersed thermocouples in mullite tubes protected against slag attack by graphite sleeves. The desired temperature was established by a calibrated Pt vs Pt-10 pct Rh thermocouple and control was then maintained using a more stable W-Mo couple. Runs were made at 1500º and 1575ºC for durations of 7.5 to 10.5 hr. The charges were calculated to yield 400 g of metal and 100 g of slag. The primary slag compositions and designation numbers were as follows:

Jan 1, 1963

By Donald Ofte, L. J. Wittenberg

The absolute viscosity coefficients and activation energies for viscous flow of bismuth, lead, and zinc are reported. The viscosities were measured in an oscillating cup viscosimeter from nearly 1000°C to within 1 deg of the melting point of zinc; 2 deg of the melting point of lead; and in the supercooled condition of bismuth, 9 deg below the melting point. Two methods of relating the change in the viscosity coeflicient with temperature were compared. From the plot of the logarithm of viscosity (77) as a function of reciprocal absolute temperature (1/T), the equations of the lines which fit the data are: AS a part of the Reactor Fuels and Materials Research program at Mound Laboratory, precise measurements of the physical properties of liquid metals are of interest because the desirability for a low vapor pressure liquid coolant in high-temperature nuclear power plants has focused attention on the properties of the liquid metals.' Also, a clearer understanding of the liquid metal state can be achieved when better measurements are available. For these reasons, the viscosity values of certain liquid metals have been determined. The viscosities of the liquid metals, bismuth, lead, and zinc are measured in an oscillating cup viscosi-meter. In this apparatus the liquid is sealed in a right-circular cylindrical cup which is attached to a torsion fiber so that the system forms a torsion pendulum. The damping effect of the molten metal upon the normal oscillations of the torsion pendulum is a function of the viscosity of the liquid. This method is advantageous because of the small amount of sample required (8 to 10 cc), the ease of remote operation of the apparatus in a vacuum system, and the containment of the liquid metal in a hermetically sealed, nonreactive, tantalum crucible. With the liquid metal sealed in the crucible, loss of liquid by vaporization and chemical reactions with atmospheric gases are prevented. Additionally, an absolute viscosity determination is obtained which avoids the sources of possible error in a relative measurement. The difficulties in a relative method include the repetitious cup calibrations, and the uncertainty inherent in the practice of calibration of the apparatus at room temperature and extrapolation to the high temperatures necessary for the investigation of most liquid metals. The oscillating cup viscosimeter was first described by Meyer in 1891.2 The first complete mathematical treatment offering an absolute measurement of viscosity with this type of apparatus was proposed by Andrade and chiong3 in 1936 for an oscillating sphere filled with a liquid. This solution was modified to include a right circular cylinder by Hopkins and Toye4 in 1950, and R. Roscoe5 in 1958. Roscoe's treatment for the calculation of the viscosity of a liquid at a particular temperature from the logarithmic decrement and period of oscillation of the torsion pendulum was used in this investigation. A detailed description of the method of calculating the viscosity from these measurements has been reported earlier.' This calculation has been programmed for the IBM 704 and IBM 1620 computers for expedition of the otherwise laborious calculations. APPARATUS The cutaway view of the apparatus in Fig. 1 shows the suspension system within the high vacuum enclosure. The low residual gas pressure. maintained between 1 x 10-4 and 5 X 10-6 mm Hg during a determination, avoided both air drag on the pendulum and

Jan 1, 1963

By James C. M. Li

The Petch relation between the flow stress and the gain size is derived from a consideration of gain boundary sources of dislocations without the need of dislocation Pile-ups. Three mechanisms for inierpreting the yield stress: the gain boundary strength, the unpinning of Frank-Read source near a grain boundary, and the generation of dislocations from the grain boundary are compared and the condition of their equivalence is shown. The effect of the average angle of misfit of pain boundaries is found to be sma11 and so is that of the average angle of misfit of subboundaries having impurities. The effect of impurities on the ledge density in the grain boundary is treated thermodynamically and a relatwn is proposed for the variation of Petch slope with impurity activity. The effect of temperature on the Petch slope is interpreted as due to the change of ledge structure in the grain boundary. It is indicated that the effect of annealing temperature may be more important than that of the test temperature and therefore should be studied. The effect of plastic strain on the Petch analysis is deduced from a work-hardening equation in which the generation of dislocations has first-order kinetics and the annihilation of dislocations has second-order kinetics. It is concluded that the Petch slope will decrease with plustic strain if the rate of annihilation of dislocations is sufficiently large. Critical experiments which may shed light on the mechanism for the Petch relation are suggested. THE relation between the yield or flow stress, 0, and the grain size, l, was first proposed by all' and later studied more extensively by Petch and co-workers, who also proposed a similar relation for the fracture stress and deduced from these a grain-size effect of the ductile-brittle transition temperature. The microscopic mechanism used by all' and petch2 involves a pile-up of dislocations of like sign generated from a Frank-Read source. The yielding or flow takes place when the pile-up exerts sufficient stress at the grain boundary so that the plastic deformation can propagate from one grain to another. If the average strength of the grain boundary is ai and the average length of the pileup is lp, the Petch slope, k, is given by" where p is the shear modulus, b the Burgers vector, and v the Poisson ratio. This slope will be independent of the grain size if l/lp is a constant. This is possible, since, if the Frank-Reed source is situated near the grain boundary, lp = 1, and if it is situated in the middle of the grain, Ip = 1/2. cottrell,12 also using the pile-up mechanism, proposed that the stress concentration at the grain boundary will initiate Frank-Read sources near the grain boundary and in this manner a Lüders band can propagate from one grain to another. Assuming that the average distance between the Frank-Read sources and the grain boundary is 1, and the unpinning stress of the Frank-Read sources is op, Cottrell obtained the following Petch slope: This slope will be independent of the grain size if ls is independent of the same, which is not as obvious as the condition, Ip = I for Eq. [2]. In addition to this assumption, the direct relation between the Petch slope k and the unpinning stress, up, was recently questioned by Johnsonon grounds that it is inconsistent with the following observations: the independence of k with temperature and strain rate, and the small k in columbium, which, like iron, has a sharp yield point. As pointed out by ohnson," the most important objection both to the Hall-Petch mechanism, in which the strength of the grain boundary plays the role in yielding, and to the Cottrell mechanism, in which the unpinning of Frank-Read sources plays the role in yielding, is the lack of direct observation of the pile-ups. The dislocation structure in deformed iron has been examined recently in the electron microsope.'-' Dislocations appear to be generated from grain boundaries or other interfaces; they form clusters and tangles within the grain at very early stages of deformation, even in the Lüders band, if the deformation is slow or at normal and elevated temperatures. Although it is still too early to interpret bulk properties from thin-film observations, it does seem worthwhile to look for a mechanism for the Petch relation which does not require dislocation pileup. SUBBOUNDARY SOURCES In order to show that a consideration of grain boundary sources can lead to the same Petch relation as does the consideration of the strength of the grain boundary, we shall first discuss the case of a simple tilt boundary whose elastic properties have been studied in detail.17 The strength of a partially

Jan 1, 1963

By J. H. Schulman, M. H. Buckenham

Although much interest has been taken in the use of mixed collectors in flotation, this investigation is probably the first in which oppositely charged collectors have been considered. The results obtained and the techniques used could well be applied in the behavior of other mixe the behavior of other mixed collector systems and could possibly explain the effective flotation results which have been reported when various collector combinations have been used. Collectors conventionally employed in flotation systems are soluble in water, but many of their homologs of longer hydrocarbon chain length are insoluble. The properties and behavior of these insoluble compounds may be conveniently studied when they are spread as monolayers at the air/water interface on the Langmuir-Adam trough. Although some extrapolation is involved in applying effects observed at this interface to the solid/liquid interface where the action of collectors is most important in flotation, the technique nevertheless is most useful for the study and interpretation of flotation phenomena. Of particular interest in this field are investigations on the insoluble monolayers of the fatty acids, alkyl sulfates and alkyl amines; the penetration of these insoluble monolayers by soluble surface active components and their interaction with metal ions from the underlying solution.'-' Unfortunately, the insoluble xanthates and related compounds do not exhibit stable monolayer properties due to rapid oxidation at the air/water interface and, therefore, cannot be studied directly in this way. These approaches have enabled Leja and Schulman8 to suggest mechanisms explaining dynamic attachment of mineral particles to air bubbles involving collector-frother interaction and the adsorption of collectors onto mineral surfaces. In this and other papers 9-12 considerable evidence is presented to support the concept of collector-frother and metal ion-monolayer interaction and to emphasize the value of monolayer techniques in elucidating the flotation system. Molecular interactions resulting from monolayer penetration are determined by the nature of and the association between both the polar and nonpolar groups of the two molecules concerned. Stable complexes are formed on penetration when interaction takes place between both the polar and nonpolar groups, and although the resultant complexes are not necessarily true chemical compounds, the properties of the molecularly associated complexes are very different from those of the individual components. Shortening of, or changes from, a straight hydrocarbon chain in one of the reacting molecules reduces considerably the stability of the associated complex as do changes in temperature, pH and substrate composition. The effect of hydrocarbon chain length becomes most important when observed effects are to be applied in flotation studies where soluble homo-logs and, therefore, much shorter hydrocarbon chain lengths are used. The present investigation is based on Langmuir trough work carried out by Bowcott,l3 who studied the penetration of insoluble amine monolayers by potassium lauryl xanthate. Bowcott observed that cetyl amine monolayers were readily penetrated by xanthate, but found that with time the high film pressures resulting from penetration and association fell off, indicating decomposition and ejection of xanthate from the film. This decomposition was pH dependent. Of particular interest in this work were studies on an equimolecular mixed monolayer of the fully N-substituted ammonium compound, for example, cetyl trimethyl ammonium iodide (CTAI) and potassium cetyl xanthate. Despite the fact that the CTAI is water soluble and the xanthate on its own is incapable of forming a monolayer, the mixed film was stable up to a surface pressure of 67 dynes per cm. In this condensed state the xanthate was stabilized against atmospheric oxidation, although iodine injected beneath the film caused an immediate collapse. The stabilizing of xanthate against oxidation by association with an alkyl trimethyl ammonium bromide (TAB) could be important in flotation, and a study of the performance and behavior of mixed collectors therefore was undertaken. A modified Hallimond tube operated under controlled conditions was used to evaluate flotation. Surface tension measurements were made to investigate the properties of the soluble

Jan 1, 1963

By Wingham D. W

Based upon the previous work of Norman & Loeb, a method was used to assess the comparative wearing properties of ten different alloys being used, or being considered for use, as mill liners and grinding media at Mount Isa, The materials to be tested were obtained in the form of large diameter balls, and were run, along with the regular ball charge, in a large ball mill operating under normal grinding conditions. At selected intervals, the test balls were removed from the mill, weighed and identified, and their relative wear rates determined.INTRODUCTIONInformation in metallurgical journals, from local iron and steel foundries, and from various metal promotional organizations has suggested that the various alloy compositions available should be examined and assessed for possible use as milllfners and grinding media.Previous attempts at evaluation of recommended materials for these applications elsewhere, have usually involved the purchase of large quantities of grinding balls or complete mill liner sets, requiring running periods of up to two years or more. As well as being both a costly and lengthy procedure, the information obtained may be of little significance, due to changes in milling practice, and ore characteristics during the period of operation.To overcome these difficuities, a method was adopted based on the short time wear rate test recommended by Norman & Loeb (1949) and Norman (1957) in which all the materialsunder consideration are ·subjected·concurrently to the conditions of service.Previous calculations of wear rates have been dependent1. Senior Metallurgist (Materials), Mount Isa Mines Limited.2. Metallographer, Mount Isa Mines Limited.Manuscript received at The Institute, 22nd April, 1963, and presented to the1963 Annual Conference.

Jan 1, 1963

By Harry M. Mikami, A. Gene Sidler

Chemistry of the evolution of materials in contact with copper converter tuyeres is delineated by means of analyses of periodic punch rod samples taken during a converter cycle. Lining samples from known peripheral and end locations from three converters were investigated chemically and petrographically. One set of eight specimens representative of all lining parts was removed for study before completion of the campaign. Purely surface removal by slag action is minor. Slag filling of interconnecting cracks extending to the hot face results in a "stoping'' action which shapes the hot face contour and is a significant factor. Major wear mechanism is believed to be copper metal slabbbing caused by metal first penetrating joins and invading fractures or impregnating brick structure laterally from the joints. Importance of lining design and joint fit are emphasized. New laboratory tests are indicated. In the copper converter, molten matte, which is essentially a solution of iron and copper sulfides, is blown with air to produce blister copper. During the first stage of the process the FeS component is oxidized to SOz and FeO, the latter combining with a siliceous flux to form a predominantly ferrous silicate slag. Successive increments of matte and flux are charged, blown, and skimmed of slag until sufficient CuzS ("white metal") has accumulated. This white metal is then blown to copper metal in the final or blister-forming stage by the oxidation of sulfur to SOz and the reduction of combined copper to metal. The reactions of both stages are exothermic so provide the required heat. Temperature is controlled by cold scrap copper, flue dusts, smelter reverts, and so forth. Considerable vari- ation in practices occur depending on the type of converter, grades of the matte and flu, and other factors. Lathe and Hodnett's' survey of world converter practices gives much information on these variations and their effects on the refractories. Principles of converting chemistry are presented by Newton and wilson,' Ruddle,' and schuhmann. Most copper converting occurs within the temperature range 2100" to 2370°F although individual smelters report1 ranges from as low as 1700" to 2240°F to a high of 2200" to 2400°F. Temperature intervals reported from beginning to end of blow varied from 45" to 540°F. Average temperature range was 2030" to 2260°F and the average interval 250°F During the matte-blowing stage varying amounts of magnetite (FeO.Fe,O,) are formed in the slag as suspended crystals and also the liquid portion of the slag will contain, in addition to ferrous silicate, some Fe20s which adds to the potential magnetite formation if the temperature falls. This is a component of the so-called "dissolved magnetite" often referred to in the literature. Although the slag may contain minor amounts of CaO, A1209, MgO, and alkalies, the principal components are Fe0-Fez03-SiO,. The phase equilibria relationships of this system have been elucidated by Muan~ and Schuhmann, et a1.' These data and estimates of converting atmospheres by schuhmann4 are useful tools in studying slag behavior. It would appear that in many cases reported magnetite contents of slags are apparently higher than actually is present at operating temperature. This is probably because much of it is formed during slag solidification. The quaternary systems which have Mg-0,1,0,' and addition to iron oxides and silica are also of interest in considering the reactions of the slags with basic refractories. The formation of magnetite has an important interrelationship throughout the pyrometallurgy of copper (Mossman,' Gronningsater and Drummond," Ruddle,' Elwood and Henderson") but its presence in the converter particularly relates to operating efficiency and lining life in certain instances. Archi-

Jan 1, 1963

By M. E. Wadsworth, J. S. Cho

Colloidal silica dissolved in aqueous suspensions of high surface area thoria was permitted to adsorb on the thoria surface. Silica in three forms was identified by means of infrared spectroscopy and characterized by Si-O vibrational modes in the 9.0 to 10.5 region. A band at 9. 1 was attributed to free unad-sorbed silica, while adsorbed silica resulted in bands of greatest absorbency at 9.4 or 10.3p, depending upon the character of the surface bonding. Size considerations, the amount of silica adsorbed, and the character of the infrared spectrum for strongly adsorbed silica has been interpreted as evidence of formation of chain or layer silica linkages on the thoria surface. Infrared spectroscopy has been used successfully in recent years for the identification of minerals and synthetic inorganic substances. Unfortunately, infrared studies of silicate minerals have not proceeded to the point that unambiguous assignments may be made for Si-O vibrational modes as affected by lattice substitutions and structures. Several investigators have presented infrared spectra of silicate minerals, 1,7 and their work has pointed to the potential value of infrared to identify minerals as well as to note the sensitivity of various Si-O modes to structural and substitutional environments. The strong infrared absorption of various Si-O vibrational modes makes the infrared method a very useful tool for the study of silica adsorbed on the surface of solids of high surface area. Spaepen et a18 studied the adsorption of silica on thoria surfaces from aqueous solutions of silicic acid up to 300°C. A general review of the application of the infrared method to the study of surface adsorption has been presented by Pliskin and Eischens.9 EXPERIMENTAL Du Pont colloidal silica, Ludox SM (16.36% SiO2) and Ludox HS (30.25% SiO2) in aqueous suspensions were used as the sources of silica for the adsorption studies. The thoria used for this study was supplied by Union Carbide Nuclear Co.* under the preparation *Chemical Technology Div., Union Carbide Nuclear Co., Oak Ridge, Tenn. . number D-16-650. It was fired from the oxalate at 650°C and had a surface area of 32.4 ± 0.6 m2 per g measured by nitrogen adsorption. The chemical analysis of the D-16 thoria in ppm was: CO3= (5500), NO3- (< 4), so4±PO4 (100), and Si (20). The Ludox silica was placed in contact with the thoria in a two-liter autoclave10 between room temperature and 250°C. Slurries were made by placing 1 g of thoria in one liter of distilled water containing various additions of the silica sol. Samples were removed from the autoclave by opening a small stainless steel valve. Extracted samples were centrifuged for 10 min and excess solution was decanted. The sample was then dried for several hours at 80°C. Infrared samples were prepared by thoroughly mixing 10 mg of the thoria with 400 mg KBr in polystyrene vials on a "Wig-L-Bug" amalgamator. Pellets were pressed under vacuum and had final dimensions of 1.2 cm diam and 1.2 mm thick. Infrared spectra were

Jan 1, 1963

By H. H. Hausner, O. V. Roman, F. V. Lenel, G. S. Ansell

The radial shrinkage during sintering of cylindrical compacts and loose aggregates of copper powder was measured. It was found to be nonuni-form from top to bottom of the samples and to depend upon the method of supporting them. The non-uniformity is due to the effect of gravity forces during sintering. Since gravity has an effect in sintering without externally applied stresses, no sharp dividing line can be drawn between conventional sintering and hot pressing. RECENT investigations of the sintering behavior of compacts1 and of loose powder aggregates2 have indicated that forces, other than those arising from surface tension effects, may play a role in shrinkage. In compacts it was shown that residual stresses from the pressing operation influence shrinkage behavior. In loose powder aggregates gravity forces due to the weight of the powder affect the ratio of shrinkage in the vertical and the horizontal direction. The main effort in the work reported here was to show that gravity plays a role also in the sintering of compacts. A few additional experiments were made confirming the effect of gravity in the sintering of loose powder aggregates. EXPERIMENTAL PROCEDURE Compacts and loose powder aggregates were prepared from irregularly shaped, electrolytic copper powder. Prior to use the powders were reduced 30 min at 400°C in dry hydrogen to remove surface oxides. Then the -325 mesh size fraction was separated from the -100 + 325 mesh fraction. The compacts were pressed at a pressure of 10,000 psi from 50 g of powder in a hardened steel die, 1 in. in diam. The height of the compacts was 0.725 i 0.005 in. An effort was made to get as uniform a green density distribution in the compacts as possible. The walls of the die were lubricated with a suspension of 3 pct of zinc stearate in acetone and the compacts were pressed using double action by first pressing the powder at 1200 psi with the die barrel supported, then removing the sup- ports and pressing to final pressure of 10,000 psi with the die barrel floating. The pressure was maintained for 10 sec. The compacts were sintered at a temperature of 925°C, generally for 1 hr. In order to maintain uniform temperature they were sintered in boats made from cylindrical copper blocks. The blocks were 2 in. in diam, either 2 or 2 1/2 in. long and, split to form the body of the boat and a lid. The body of the boat contained a cavity 1 3/8 in. wide, 1 in. deep and either 2 1/8 or 1 3/8 in. long. The longer cavity accomodated two samples, the shorter one only one sample. The uniformity of temperature distribution within the boats was checked with thermocouples welded to the top and bottom of the samples. The maximum variation between top and bottom temperatures was i 1/2°C. The actual sintering temperature was held constant within ±2°C. In order to determine the effect of gravity forces, i.e., the weight of the compacts, upon shrinkage, they were supported in the following ways during sintering: a) Full Bottom Support. The compacts rested either on a flat alundum disk or on alundum powders. b) Partial Bottom Support. The compacts rested on a graphite cylinder, 0.3 in. in diam which formed a projection on a larger graphite disk. It is difficult to balance the compact on the small projection. To avoid having the compact tip, a small hole was drilled through the compact and through the graphite disk and its projection. The graphite disk was then suspended from the lid of the boat by a thin iron wire which passed through the holes in the disk and the compact. c) Top Support, first type. A hole 3/32 in. in diam was drilled diametrically through the green compact 3/16 in. from the top of the compact. The compact was sintered suspended from an alundum rod (thermocouple protection sleeve) inserted into the hole. d) Top Support, second type. A hole was drilled axially through the center of the compact. The upper part of the hole from the top surface of the compact one fourth of the way down was 1/16 in. in diam; the lower part of the hole from the bottom surface three fourth of the way up was 3/32 in. in diam. The compact was suspended from the lid of the boat by an iron wire passing through the upper part of the hole and then tied into a knot. The loose powder aggregates were made by filling l in. deep, l in. diam cylindrical graphite molds with -325 mesh powder. To achieve uniform density in all the loose powder aggregates, the powders were settled in the molds by placing the

Jan 1, 1963