Search Documents

By M. N. Shetty

LARGE copper whiskers (-100 p) of 11111 orientation were tested in a floor-model Instron testing machine, at liquid nitrogen temperature. (Testing methods will appear elsewhere.) Whiskers deformed by twinning after some initial deformation. A load-elongation curve at the onset of twinning is reproduced in Fig. 1. Twinning was confirmed by taking a back-reflection Laue picture, using a slit colli-mator, which showed distinct splitting of reflections. The tensile stress reached just before twinning is about 1.4 x 107 g per sq cm (-7.0 x106 g per sq cm—resolved shear stress) which drops to 1.2 x107 g per sq cm (-6 x 106 g per sq cm—resolved). This twinning stress is about five to ten times larger than the value for bulk single crystals of copper deformed at 77°K (-106 g per sq cm—resolved). Twinning models based on Cottrell-Bilby's pole mechanism are discussed in detail by Venables.' In the present work a mechanism based on the idea of failure of a Lomer-Cottrell barrier by recombination will be proposed. An L-C barrier may fail either by recombination or by dissociation.3 Fig. 2 provides the necessary information. It shows that the stress necessary to break such a barrier is about 1.8 x 107 g per sq cm by recombination and 4 x 107 g per sq cm by dissociation at 77°K. The twinning stress reached by whiskers is comparable to the stress level required for failure of an L-C barrier by recombination. (Stroh himself points out that his calculations should not be taken too literally.) We consider a segment of the L-C dislocation which has recombined (AB in Fig. 3) over a length to form the total dislocation which then glides in the

Jan 1, 1965

By T. K. McMahon

Formally, a mathematical model could be defined as: A set of equations whose solution will approximate the response of a physical process or system to a set of stimuli which appear as parameters in the equations. The purpose of a mathematical model is to permit the rationalization of experience to proceed by simulation rather than by physical experimentation. In the application of digital computer control to an industrial process, the mathematical model of the process (subsequently called the process model) is needed to calculate the present process performance from the measured variables and to predict the response of the process to a control change. Functionally, the cardinal element in process model development is a concise set of control objectives. These, besides implicitly defining the boundaries of the system to be modeled, will determine the accuracy demanded of the model its nature: dynamic or steady-state, and so forth, The objectives should explicitly define what process efficiencies, production rates, qualities are to lie within the scope of the computer control project, thereby providing a basis for simplifying assumptions in the development of the model. This requirement, a limited set of control objectives, is so often disregarded in formulating industrial control problems that its repetition can scarcely be avoided.

Jan 1, 1965

By James F. Neill, O&apos

Brown iron ore resources in Barbour, Butler, Crenshaw, and Pike Counties were investigated in a drilling program and geological study by the Federal Bureau of Mines in cooperation with the Alabama Geological Survey and the University of Alabama. The aggregate footage drilled was 18,010 linear feet. When developed, reserves of 12,664,000 long tons of crude ore were indicated, containing from 26.9 to 29.0 percent iron and 0.2 to 1.6 percent manganese under a maximum overburden of 40 feet. Total inferred crude ore for the four counties was calculated to be 827,700,000 long tons. Beneficiation of samples by simulated log washing and use of a 1/8-inch screen yielded from 46.8 to 51.7 percent iron and 0.2 to 2.6 percent manganese. Screen-test studies indicated no appreciable interlocking between the iron and manganese minerals and the waste particles of materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size. While an indicated 2,198,000 dry long tons of usable iron ore can be recovered, sink-and-float tests show that it may be possible for 4,654,000 dry long tons to be recovered by other than log washing. However, applicable commercial processes have not been demonstrated.

Jan 1, 1965

By Don M. Jackson

The techniques for the growth and controlled, graded doping of silicon epitaxial overgrowth layers were established. Grading of- impurities such as arsenic or boron in arbitrarily chosen profiles oiler four orders of magnitude (from I X 10Lg to 1 X 10L5 cm) was accomplished. The graded structures were grown in a stepwise manner where in the profiles were approximated by growing many separate layers with small doping-level changes between layers. Masked-area growth of silicon through windows in a SiO2 masking film was acconiplished through the simultaneous injection of HCl gas 102th Sic14 in the epitaxial reactor. The HCl served to inhihit the growth of silicon on the Sz02 surface, and also to control the cross-sectional profile of the silicon mesas. silicon from the substrate was etched out through the windows, and then epitaxial material was used to fill the holes hack in to form planar diodes. Simullaneous HCl injection was adapted to control the cross-section profile of the hack-filled regions. Arsenic-huried regions beneath in te- In recent months, the epitaxial growth process in semiconductor materials technology has evolved into a complex system directed at both material improvement for better monolithic integrated-circuit characteristics and the development of new silicon structures for future integrated-circuit needs. The advent of high-temperature HC1 gas etching1 grated-circuit transistors reduced V(SAT) by slightly more than one third, bringing this parame-ter to that of an isolated component transistor. When arsenic was diffused into the starting sub-stvate, it was necessary to remove any excess arsenic in order to avoid excessive audodoping of the subsequent epitaxial layer. Oxide isolation of single-crystal regions in a substrate provided complete electrical isolation of integrated-circuit components, thereby eliminating parasitic capacitance which is inherent in standard integrated-circuit processing. The process involved the etching of deep mesas on silicon Wafers, the formation of an oxide over the mesa surface, and then the deposition of several mils of polycrystalline silicon over the oxide. The original substrate was lapped and polished allay until the mesas were left isolated in the polycrys-talline matrix. The Final components were fabri-cated in the single-crystal islands. Speed and power-handling capabilities of standard circuits were improved through the process. wherein work-damaged material is removed from the surface of the silicon wafer just prior to the silicon deposition step has made it possible to grow silicon films with structural quality that approaches that of the substrate. HBr used in the same volume ratio as HC1 etches silicon at the same rate and with the same results as HC1. Recent developments in epitaxial materials technology have occurred in the areas of precise doping control, buried prediffused regions between over-

Jan 1, 1965

By Stephen Utter

Stresses induced by block-caving mining were estimated from in-place measurements of strain or deformation in rock and concrete around mine openings. The four types of gages used for measurements in the Climax Molybdenum mine during 1959-61 were Whittemore gage, Carlson strain meter,2 Valore strain cell, and Climax extensometer. Gage performance in the laboratory was evaluated by stressing instrumented rock and concrete specimens in a universal testing machine and by comparing measurements taken by the gages and a standard gage. Gage performance in the mine was evaluated by comparing measurements taken during an 18-month test. The Whittemore gage, Carlson strain meter, and the Climax extensometer proved suitable for the investigation; the Valore strain cell, effective in the laboratory tests, gave erratic measurements in the mine.

Jan 1, 1965

By Huey-Lin Luo, T. R. Anantharaman, William Klement

Two new metastable phases have been obtained in Au-Ge alloys by rapid cooling from the melt. One is of the hep structure with near-ideal axial ratio and may be considered a Hume-Rothery phase. The other has a complex tetragonal structure (a = 11.627Å and c = 22.191Å for the Au60Ge40 alloy) and may be looked upon as a superlattice made up of forty-four fee unit cells. Alloys with the tetragonal phase are charactevized by marked preferred orientation. The metastable constitution of the Au-Ge alloys is discussed with reference to the rate of cooling from the melt. THE Au-Ge equilibrium diagram features a rather deep eutectic near 27 at. pet Ge with a maximum solid solubility of 3.2 at. pet Ge in gold and is similar to the Ag-Ge, Ag-Si, and Au-Si diagrams.' The present study of the effects of rapid cooling from the melt on the structure of Au-Ge alloys constitutes an extension of similar investigations2-8 in this laboratory on alloys of noble metals with germanium and silicon. Nonequilibrium hep structures have so far been obtained by quenching Ag-Ge2, 3 and Ag-Si4, 5 alloys from the melt; an Au-Si alloy of approximately eutectic composition has been found6 to solidify in a noncrystalline state. EXPERIMENTAL PROCEDURES Twenty-nine alloys prepared from gold of 99.9+ pet and germaium of 99.999 + pet purity were investigated. The method of alloy preparation, the technique of rapid quenching from the melt, and the X-ray diffraction procedures were similar to those described previously.3, 4 Essentially, small sections (-20 mg) of thin alloy rods (-1 mm diam) were rapidly heated up to 1200°C in a graphite crucible under argon and the liquid alloy ejected by a helium blast onto a polished copper strip held on the inner periphery of a rotating wheel. The resulting thin foils were examined with or without the copper substrate in a G.E. X-ray Diffractometer or in a 114.6-cm-diam Debye-Scherrer camera. RESULTS Table I gives the constitution of liquid-quenched Au-Ge alloys, as estimated from intensities of X-ray reflections from the corresponding phases, viz., a (fee solid solution), ß (hep phase), ? (tetragonal phase), and diamond-cubic (dc) germanium. Despite unavoidable variations in the quenching rates, the proportions of the phases in different alloys were generally reproducible and stable at room temperature. There was no evidence of quenching strain, since the a doublets were well-resolved in high-angle Debye-Scherrer reflections in all cases except where stacking faults in the a fee and ß hep structures contributed to X-ray line broadening. The ß and ? metastable phases showed signs of decomposition to the equilibrium a phase and germanium only after a few hours annealing above 100°C. A few alloys around the eutectic composi-

Jan 1, 1965

By Luis F. Morán

El presente texto señala algunos aspectos que comprende el proyecto de San Nicolás desarrollado por Marcona Mining Company. El proyecto señala las facilidades de la mina, transporte, almacenamiento del mineral, plantas chancadoras, lavado y concentración por medio denso, concentración magnética, instalaciones para almacenar productos comerciales, formación de pellets verdes, endurecimiento, terminado y control del proceso.

Jan 1, 1965

By Arnulf Muan, D. P. Masse

PHASE relations in the system CoO-SiO2 have been determined as a basis for further investigations of thermodynamic properties of olivine solid solutions involving Co2SiO4 as a component. Previous data on the system CoO-SiO2 are incomplete or uncertain. Biltz and Lemke1 determined the melting point of cobalt orthosilicate as 1345°C , but Asanti and Kohlmeyer2 have later found a considerably higher temperature, 1420°C. The latter authors also studied melting relations of one mixture on the CO side and two mixtures on the SiO2 side of the orthosilicate composition and sketched a tentative phase diagram for a limited composition range of the system. However, no phase identification was carried out, and the authors left unanswered the question of the possible existence of a stable meta-silicate phase. Greig3 showed that a 90 wt pct SiO2-10 wt pct Co mixture at 1725°C consists of two immiscible liquid phases. The quenching technique was used in the present investigation. Mixtures of high-purity cobalt oxide ("Fisher Certified") and dehydrated silicic acid ("Baker Analyzed") were equilibrated in air atmosphere. The samples were then quenched to room temperature and the phases present were identified by microscopic and X-ray examination. The samples were kept in small envelopes made from thin (0.0004 in.) platinum foil. Thermodynamic data which have become available recently for Pt-Co alloys4 were used to check that the losses of COO from the oxide samples by alloying of cobalt with platinum in the present investigation were too small to change significantly the compositions of the oxide material during the equilibration. A vertical tube furnace with an 80 pct Pt 20 pct Rh resistance winding was used in runs up to 1510°C. Temperatures in these runs were measured with a Pt vs 90 pct Pt 10 pct Rh thermocouple calibrated against the melting point of diopside (CaMgSi2O6, 1391.5?C). The given temperatures as measured by this technique are estimated to be accurate to *5°C. Quench runs at temperatures above 1650°C were made with a modified Roberts and Morey5 strip furnace, using strip resistors composed of a 60 pct Pt-40 pct Rh alloy. Temperatures were measured with an optical pyrometer which was calibrated against the liquidus temperature of a mixture composed of 10 wt pct CaO, 90 wt pct SiO2 (1707°C). The temperatures measured with this technique have an estimated accuracy of +15°C. The results are shown graphically in Fig. 1. Only one intermediate phase, the orthosilicate Co2SiO4 with olivine-type structure, is stable in addition to the end members cobalt oxide and silica. The melting point of the orthosilicate was found to be 1415" ± 5°C. The metastilicate CoSiO3 is not stable at the temperatures of the present investigation. The two eutectic points in the system CoO-SiO2 where COO plus olivine, and olivine plus silica, coexist with liquid were found to be 72 wt pct COO and 1407°C and 63 wt pct COO and 1381°C, respectively. The melting point of cobalt oxide in air was taken as 1745?C, based on the previous data of Aukrust and Muan.6 Within limits of error (+ 5?C), identical eutectic temperatures to those determined in air were found when two representative mixtures were equilibrated at 1 atm O2 pressure and in an atmosphere of 84 vol pct CO2, 16 vol pct H2. This suggests that changes in oxidation state of cobalt in the condensed phases are not significant as far as their effect on the phase relations are concerned. This inference was substantiated by failure to detect7 any "excess oxygen" (i.e., oxygen in excess of that contained in Co2SiO4) in a sample of orthosilicate composition equilibrated in air 10°C above the liquidus temperature and subsequently quenched to room temperature. This work was carried out as part of a research program sponsored by the U.S. Atomic Energy Commission under Contract No. AT(30-1)-2781.

Jan 1, 1965

By I. R. Kramer, H. Shen, S. E. Podlaseck

The tensile and creep properties of aluminum in vacuum have been investigated. It was found that the general effect of a vacuum environment was to reduce the rate of work hardening. Results obtained from creep tests showed that lowering the test pressure from 2 x 10-4 to 10-7 torr produced a decrease in the activation energy as much as 500 cal per mole. An attempt is made to explain these effects in terms of how the surface-stress field of a specimen may be affected by a vacuum environment during plastic deformation. In a previous paper,' the results were reported of some of our early work on the effect of vacuum environment on the stress-strain curve of aluminum single crystals. This effort has been extended to the studies of the tensile and creep properties in vacuum as a function of various metallurgical parameters. Some of the recent surface-effect studies2'3 have revealed that a region of high dislocation density, the so-called "debris" layer, is formed near the surface of the specimen as a result of plastic deformation. This layer acts as a surface barrier to oppose dislocation movement. The strength of this barrier depends on the surface condition such as oxidation or surface removal. Experimental results obtained from surface-removal work2, 3 indicate that such a surface barrier, which may be characterized by a stress field, affects the applied stress and the rate of work hardening. In the case of aluminum, this stress field was found to be directly proportional to the strain and the strain rate; however, the slope of this curve is independent of orientation of the crystal and may be altered by using different surface treatment. Since the escape of dislocations may be retarded by the presence of an oxide on the surface of a specimen, it is expected that a change in the rate of oxidation in vacuum will affect the process of dislocation accumulation in the debris layer. Consequently, it also affects the plastic behavior of a metal. This paper reports the changes in some of the creep and tensile properties of aluminum in vacuum and discussions of the observed effects in terms of the concept of the "debris" layer. EXPERIMENTAL PROCEDURE Tensile Tests. A sketch of the tensile apparatus is given in Fig. 1. This apparatus was contained in a bell jar (14 in. diam by 24 in. high) connected to a 10-in. vacuum system. The load was applied to the specimen by means of a gear train which was driven by a magnetic clutch located outside the vacuum chamber. The specimen, held by a pair of square shoulder grips, was attached to the load cell at the top and the drive gear at the bottom. A displacement transducer was placed between the two grips as shown in the figure to measure the elongation. Signals of elongation and load were amplified and recorded on an X-Y recorder. The system was capable of detecting loads as small as 0.025 lb and displacements of 0.0002 in. Shoulder-grip specimens of aluminum single crystals, having a nominal square cross section of 1/8 by 1/8 in. and a 3-1/2-in, gage length, were grown by the Bridgeman techniques. The original purity was 99.997 pet. The orientations of the crystals investigated are shown in Fig. 4(a). The crystals were annealed at 600°C for 2-1/2 hr, electropolished, and placed in the vacuum test chamber without any delay. All the crystals were deformed at a strain rate of 4 x 10-5 sec-1 at 24o ± 3°C. A study was made to find whether a chemically passive surface film would give the same effect as a vacuum environment. Specimens of aluminum 1100 (0.187 in. diam with a grain size of 0.1 mm)

Jan 1, 1965

By J. W. Jensen

EXTENSIVE research and development was performed on the manganese-copper vibration-damping alloys to determine the relationship between the properties of the alloys and variations in composition, fabrication, Mid heat treatment. Mn-Cu alloys with unusually high specific damping capacity, 20 to 25 percent at a stress of 5,000 psi, have also the following useful properties: Tensile strength, 90,000 to 110,000 psi; yield strong, 60,000 to psi; elongation, 20 to 25 percent; hardness, 90 Rockwell B; and fatigue limit at, 28,000 to 30,000 psi. Both standard and special methods of testing were employed to obtain data on strength, modulus, hardness, resistivity, dilatation, micro-structure, crystal lattice, and damping capacity. The extensive tabular and graphical data on these properties are presented for alloys containing 50 to 85 percent as quenched d solution) and after various aging treatments. Expansion coefficients for all Mn-Cu solid solutions are graphed and a dilatometer study of contraction during aging is reported. Although high damping capacity is associated with aging to precipitate a-Mn from solid solution, with a cubic-tetragonal transformation and with the occurrence of antiferromagnetic ordering in Mn-Cu alloys, a tenable theory of the damping mechanism has not been reached.

Jan 1, 1965

By H. W. Hitzrot, R. H. Limons, L. V. Fegan

The testing of a new method for measuring pellet-bed temperatures in the traveling-grate or shaft furnace is presented in this paper. This method, using silver-palladium alloy wires as indicators, overcomes disadvantages existing in the methods based on the use of thermocouples which are costly and time-consuming. The authors have developed and tested a new method for measuring pellet-bed temperatures in the traveling-grate or shaft turnace through the use of silver-palladium alloy wires as indicators. This method overcomes the disadvantages of existing methods, which, based on the use of thermocouples, are generally costly and time-consuming. For example, in the case of the traveling-grate furnace, the installation of an instrumented pellet, together with its attached thermocouples, requires stopping the furnace, with resulting loss of production time. As for temperature measurement in the shaft furnace by the existing method, the movement of the shuttle-car feeder seriously interferes with both the actual insertion and the resulting distribution of continuously fed thermocouples. The authors have overcome these difficulties by using, as temperature indicators, a range of silver-palladium alloy wires that can be easily recovered, after firing at any desired location in a pellet furnace. Silver-palladium wires having specific melting points from 2000°F to 2500°F are enclosed in ceramic capsules. Each capsule is placed in a ni-chrome wire basket filled with a sample of green pellets, the baskets being the means for recovering the capsule after firing. After the encapsulated wires have been exposed to the firing cycle, the alloy wires are examined to determine the maximum temperatures attained by the pellet sample. This method gives accurate, rapid determinations of maximum temperatures attained during pellet induration in either the traveling-grate or shaft furnace The new method has the following advantages over existing methods: 1) it is less expensive; 2) no furnace downtime is required; 3) the testing units can, be made in quantity in advance; 4) measurements can be made in rapid succession at all desired locations; 5) measurements of maximum firing temperatures are more accurate; 6) on the basis of points 4 and 5, the new method gives a more reliable picture of the correlation of pellet quality, petrographic textures and maximum temperatures, thus providing a more effective quality-control tool. A disadvantage of the method is, of course, that the measurements are not continuous and only maximum temperatures are determined. TEST PROGRAM Preparation of Materials: CALIBRATION OF ALLOYS - In the following discussion the term "bead point" (see Fig. 1) refers to the temperature at which each alloy begins to melt and form a bead. Fig. 2 gives the bead point curve for silver-palladium alloys. Before the alloys are used in plant tests, the bead point of each alloy should be determined in the laboratory to verify the alloy compositions. Once a given alloy has been calibrated, it can be

Jan 1, 1965

By L. S. Darken, H. A. Wriedt

An investigation has been made of nitrogen absorption by the lattice defects in a low-carbon steel afte~ Plastic deformation. Specimens in which defects were distributed by various combinations of cold rolling and vacuum heat treatment were equilibrated with controlled ammonia + hydrogen mixtures at 300° to 450°C to study the relation between the solubility and the thermodynamic activity of nitrogen. The results are interpreted in terms of nitrogen being absorbed upon two different types of defect sites, called A sites and B sites. The concentrations of these sites are calculated for specimens with various histories of straining and annealing; and the thermodynamic relations descrihing the equilibrium distribution of nitrogen among the A, B, and ordinary interstitial sites in ferrite are evaluated as follows: THE generalization that the solute atoms in a solid solution interact with imperfections in the solvent lattice is now universally recognized and the subject of an extensive literature. All types of imperfections—point, line, or surface—exhibit these interactions, but the relative importance of each type depends upon its concentration, the strength of its interaction with the particular solute atom, and whether the interaction is attractive or repulsive. The strength and sign of the interaction vary with the vectorial displacement of the solute atom from the imperfection in the crystal. The concentration of lattice defects increases during plastic deformation and the effect of the imperfections upon the solute atoms is usually perceived only after cold work or irradiation. Two experimental methods have previously been used to observe the effects of interaction between nitrogen atoms and lattice imperfections in a iron. Internal friction, which was first used for this purpose by Dijkstra,1 has been applied more often than the electrical-resistivity method of Cottrell and Churchman.2 The method of the present investigation has not been used before.* Uniform specimens of steel with a metastable defect structure are produced by cold rolling and subsequent heat treatment below the recrystallization temperature. Variations in the defect structure are obtained by varying the amount of strain and the heat-treatment conditions. The specimens are then saturated with nitrogen at moderately elevated temperatures in ammonia + hydrogen mixtures having various thermodynamic activities of nitrogen below saturation with Fe4N. From the nitrogen contents of analyzed samples, the metastable equilibria of interactions between the defects and nitrogen can be established and the concentration of sites for nitrogen atoms in the lattice defects calculated. A steel was used in the present experiments instead of purified iron or iron alloys because the amount of nitrogen absorbed at defects is larger in the steel over a much wider range of experimental conditions and could therefore be measured more accurately. The effect of alloy composition is discussed in Part II of this paper; it is sufficient to say here that impurities and phase heterogeneity in ferritic alloys favor the generation and/or retention of larger defect concentrations during plastic deformation and annealing at 300° to 500°C. MATERIALS AND EXPERIMENTAL PROCEDURE The experimental specimens were prepared from stock of a low-carbon steel, which will be called "X steel" here, with the composition: C, 0.12 pct; Mn, 0.43 pct; P, 0.010 pct; S, 0.034 pct; Si, 0.007 pct; As, 0.086 pct; Cu, 0.022 pct; Ni, 0.009 pct; Cr, 0.003 pct. The stock was all from a single ingot made by the basic open-hearth process, which was hot-rolled to strip 0.080 in. thick.. This hot-rolled strip, given the code designation "XH", was the starting material for preparing a series of cold-rolled sheets. The latter are designated "XC27",

Jan 1, 1965

By M. Copeland

Phase relations of gadolinium alloyed, up to 40 weight-percent (wt pct), with AISI 304-type stainless steel were established. Body-and face-centered cubic iron-rich solid solution phases and several intermetallic gadolinium-containing compounds of variable composition that approximated the formulas Fe9Gd, Ni7Gd2, Ni3Gd, Fe2Gd, NiGd, and NiGd3 were identified. The intermetallic phases Fe9Gd and Ni7Gd2 were noted to melt at about 1,080° C at about 0 to 2 wt pct gadolinium. The melting temperature of Fe9Gd increased with increas-ing gadolinium content to a plateau at about 1,230°C and 30 wt pct gadolinium, and the melting point of Ni7Gd2 decreased to a plateau at 900° C and 30 wt pct gadolinium where Ni3Gd, NiGd, and Fe2Gd coexist. Body-centered cubic iron solid solution was stable from 1 to 2 wt pct gadolinium to higher contents, 30 wt pct gadolinium or possibly more, and face-centered cubic iron up to 12 wt pct gadolinium below 1,200° C. The stability of these phases above 1,200° C was not resolved except for the mel points. A limited number of fabrication variables as well as mechanical and corrosion properties of alloys containing up to 5 wt pct gadolinium were studied. Equilibrating and forming operations were best conducted at about 940° to 1,080° C. Some variability in the yield and tensile strengths of alloys was noted; however, there was a continual decrease in ductility and impact resistance with increasing gadolinium contents. The resistance of gadolinium alloys to corrosion in water at 354° C was about the same as stainless steel.

Jan 1, 1965

By Vito J. Colangelo

The primary object of this study was to determine the effect of ferrite and its orientation upon the mechanical properties of a precipitation -hardening stainless steel with particular attention to the short-transverse properties. The investigation consisted of Jour major parts : the preliminary investigation of billet properties, the effect of forging reduction and ferrite content upon mechanical properties, the effect of notch orientation upon impact strength, and the relationship of heat composition to ferrite content. Low ductility and impact strength in the short transverse direction were found to he associated with the orientation and shape of- the ferrite plates. It was also determined that impact strength varied with notch orientation. The test values obtained with the notch perpendicular to the plane of the ferrite plate were lower than those obtained in the notch-parallel condition. The over-all investigation showed that high ferrite contents in general had a deleterious effect upon mechanical properties and that the ferrite content could he minimized by exercising rigorous control of the heat composition. A careful balance of elements, nitrogen in particular, must he maintained in order to reduce the formation of ferrite. THE precipitation-hardening stainless steels were developed to fulfill a need for high-strength corrosion-resistant alloys. In the annealed condition they are soft and ductile and possess many of the desirable characteristics of the austenitic stainless steels. In the hardened condition, the alloys exhibit the high strength and hardness of the martensitic stainless steels. The alloy under consideration in this investigation has a nominal composition as follows: C Mn Si Cr Ni Mo N 0.13 0.95 0.25 15.50 4.30 2.75 0.10 The hardening mechanism is identical to that of other hardenable steels in that it depends upon the transformation of austenite to martensite. This alloy because of its annealed structure and its ability to be hardened combines the desirable forming and corrosion properties of the austenitic grades with the high hardness and strength levels attainable with the hardenable grades. The reason for this apparent duplicity of proper- ties can be explained by considering a basic metallurgical difference between the hardenable stainless steels and those of the austenitic group. Both types are austenitic at 1800°F but, while the martensitic grades transform to martensite upon rapid cooling to room temperature, the austenitic grades remain austenitic even when cooled to temperatures below room temperature. The major difference then is in the degree of austenite stability. This stability can quantitatively be described by the Ms temperature. The Ms is defined as that temperature at which austenite begins to transform to martensite. The austenitic grades for example may be cooled to -300°F without producing significant quantities of martensite. The hardenable stainless steels on the other hand have an Ms temperature in the vicinity of 400" to 700°F. In cooling to room temperature, these alloys traverse the entire Ms-Mf range and show almost complete transformation to martensite. The semiaustenitic stainless steel, however, occupies an intermediate position with respect to its austenite stability. The analysis is so balanced that the Ills temperature lies at or slightly above room temperature. The resulting alloy retains much of its austenite at room temperature and yet responds to hardening heat treatments. Achieving this delicate balance of elements is therefore of great importance. Slight imbalances of the equivalent Cr-Ni ratios frequently result in the presence of 6 ferrite. It is the effects of this ferrit with which we are concerned, more specifically the effect of the quantity and ferrite orientation upon mechanical properties, particularly ductility. PROCEDURE A) Preliminary Investigation of Billet and Forging Properties. In order to determine the effect of ferrite on billet properties, billet stock from three heats with various ferrite contents was utilized. Tensile specimens were obtained in the transverse and longitudinal directions from this material and heat-treated as shown in Tables I and 11. Forgings were made from these same heats, the purpose being to determine what effect, if any, the ferrite might have upon the mechanical properties. These forgings were made in such a manner as to elongate the ferrite in the longitudinal and transverse directions. The method of forging was as follows. A section was cut from a 6-in.-sq billet of Heat A and flat-forged to 1-1/2 in. thick. Working was done from one direction only with no edging passes as shown

Jan 1, 1965

By Ernest Hucke

This paper will cover basic pneumatic and electronic sensors, transducers, transmitters and their application in the Mining Industry.

Jan 1, 1965

By John Convey

This paper, a follow-up to an earlier study, gives the history of Canadian developments in mineral processing from 1921 to the fall of 1964. It deals extensively with comminution and flotation, and then goes on to cover the fields of gravity concentration, magnetic concentration, cyanidation, the processing of uranium ores, and instrumentation. Several outstanding examples of installations are given. The paper concludes with a discussion of present-day trends in mineral processing. Introduction T HE history of the developments in mineral processing in Canada from its earliest times to 1920 has already been published by one of the authors (1). The present paper is thus a logical follow-up to bring this history to date. From 1834 to 1920, mineral processing in Canada, as elsewhere in the world, was in its formative stage. This, however, prepared the ground for developments that have resulted in a mining empire from the Atlantic to the Pacific, a mining empire which could be said to be almost on par with that in the United States.

Jan 1, 1965

By Waugh D. M

investigations have been undertaken into the flow characteristics of mineral slurries from a number of Australian metallurgical plants including Mount Isa Mines Ltd., North Broken Hill Ltd., and Broken Hill South Ltd. Experimental equipment installed for this work included facilities for continuous recording of flow rate and pressure drop and detection of sedimentation.Although the method has subsequently been described in published literature, it is believed that the investigations included the original application of a method for correlation of the flow rate and pressure drop data. This method depends on solving by graphical methods the values of the constants k, and c in the relationship EQUATION 1 where D is pipe diameter; ?P, pressure drop; L, length; and V, mean linear velocity. Discussion of this correlation also reveals why sedimentation velocity does not necessarily vary greatly with pipe diameter.INTRODUCTIONIn order to design pumps and pipeline installations for a Newtonian fluid, measurements of the fluid's density and viscosity in any of a number of instruments are sufficient. Substitution of these values in well known equations to calculate Reynolds numbers and subsequent correlation to determine friction factors are all that is required for engineering specification.As a result of work during the last decade, particularly that of Metzner and Reed (1955) and Dodge and Metzner (1959), it is now possible to design for homogeneous non-Newtonian fluids using relatively simple instrumental measurements.These methods can sometimes be applied to thick slurries which behave as if homogeneous. However, for the...

Jan 1, 1965

By Jack G. Crump

Nuclear radiation systems for gauging solids content in process slurries and level in crushers has demonstrated acceptance in ore processing. The use of nuclear radiation for moisture analysis of bulk materials is presently receiving acceptance in beneficiating and agglomerating processes. On the horizon is the use of nuclear activation methods for continuous, qualatative and quantitative analysis of concentrate. The common characteristics of these uses of radiation is the non-contacting nature of the measurement. Unquestionably, this is the dominant reason for acceptance of nuclear methods in level and slurry-gauging. Moisture activation analysis of a product using nuclear methods retain this advantage. However, and: more importantly, they offer new solutions to old problems. The nuclear method in addition to being non-contacting, is non-destructive and provides a continuous measurement of the process variable. The system responds: to the fundamental makeup of matter, mass and elemental composition, not to secondary properties such as temperature, resistivity, or dielectric constant. Measurement is a volume rather than a surface phenomenon, thus the results can provide a truer pricture of the measured variable.

Jan 1, 1965

By Jr. Smith

The equilibrium compositions of product gases for mixtures of air with methane, propane, or ethylene at and around flame temperatures are reported. For each hydrocarbon, compositions are given for five fuel-to-air ratios--two lean, two rich, and one stoichiometric--at five pressures, from 1 to 20 atmospheres, and at an ambient temperature of 25° C.

Jan 1, 1965

By J. O. Brittain, N. R. Adsit

A number of zinc bicrystal specimens with the grain boundary loaded in simple shear were plustically deformed in creep in a vacuum at 200°C and under an argon atmosphere at 350°C. The results indicated that the amount of grain boundary sliding at a given time was controlled by the slip in the grains and was proportional to the resolved shear stress on the slip plane. Curves of grain boundary sliding vs time were found to be cyclic with no regular periodicity. ALTHOUGH grain boundary sliding (G.B.S.) has been investigated in a number of different types of tests on various materials there is substantial disagreement on the interpretation of the various observations. Gifkins1 has presented a comprehensive review of the subject of G.B.S. and fracture. He reports that the activation energy for high-temperature creep is equal to that for volume self-diffusion and that pure metals show less tendency towards intercrystalline fracture than alloys. Pure metals show appreciably greater grain boundary migration than alloys, and both grain boundary migration and grain boundary sliding follow the same general trend in time as plastic deformation during creep.' While there have been a number of different mechanisms proposed to account for G.B.S., none of the models explains all the results. Since zinc has only one prominent slip system, it was hoped that experiments on G.B.S. in zinc bicrystals might enable us to separate the effect of grain boundary angle and the effect of matrix slip and thereby resolve at least one part of this complex phenomenon. EXPERIMENTAL PROCEDURE Bicrystals of pure zinc (99.99 pct) were grown by a Bridgeman technique in a furnace having a gradient of 20°C per in. The bicrystals were seeded to a desired orientation and grown in a split graphite mold which was 3/4 by 5/8 by 8 in. The mold was enclosed in a Pyrex tube and the tube was evacuated and then filled with a small amount of argon before it was placed in the furnace. The growth rates were 1/2 to I in. per hr for the bicrystals and 1/2 to 3 in. per hr for the single-crystal seeds. The longitudinal V notches served to hold the grain boundary in position during the growth process. A schematic rep- resentation of a specimen which had been cut with a jewelers saw from the bicrystals is shown in Fig. 1. All specimens of a series were cut from the same crystal, some of which were 7 in. in length. After specimen preparation the boundary was approximately 5/16 in. long and the V notches had a radius of 1/16 in. The boundaries were straight at a magnification of X100 with the exception of a few which had a gradual radius of curvature of greater than 3.2 in.-1. Laue back-reflection photograms were taken on the specimens to check the orientation of grains in the bicrystals. The method of relating the orientation of the two lattices is shown in Fig. 1, where 0 is the angle between normal to the boundary and the trace of the basal plane, is the angle in the boundary between the trace of the basal plane and a line parallel to the V notch, and x is the angle in the basal plane between the Burgers vector and the perpendicular to the grain boundary. After mechanical polishing the specimens were chemically polished.2 Subsequent to the polishing operation the specimens were encapsuled under a vacuum of better than 25 annealed at 340°C for 1 hr to remove the effects of this handling, and again chemically polished. Finally, fiduciary marks were scribed on the specimen using a micromanipulator. Creep tests, which were conducted in a modified Bausch apparatusS with the boundary loaded in simple shear, were run at a constant load (since the boundary area remained essentially constant this is approximately constant grain boundary stress). The temperature was controlled to ±1/4°C as measured on a semiprecision potentiometer with a calibrated thermocouple. The specimens were tested in a vacuum of better than 0.5 at 200°C and in purified argon at a pressure of 1/2 atm at 350°C. The op-

Jan 1, 1965