Search Documents

By Israel Liebman

The Bureau of Mines conducted an investigation to determine those factors that are significant in affecting the velocity of flames propagating along the boundary separating gaseous fuel and air. In addition the aerodynamic motion of the gases in the vicinity of such interfacial flames was delineated. Parameters in the study included flammable zone thickness, flammable zone concentration of gradient, fuel type, and position of the flame relative to various environmental surfaces. Of all these factors, the flammable zone thickness and burning velocity of the stoichiometric mixture were found to have the most significant effect on the flame speed. Notion of the gases in the vicinity of the interfacial flames was examined by particle track and interferometric techniques. The relative velocity of the interfacial flame with respect to the unburned gas on the central streamline was found to equal the burning velocity of a stoichiometric homogeneous fuel-air mixture. In addition, it was observed that the composition of the lean fuel-air mixture at the boundary of the combustion zone appears to be less than that defined as the fuel's lower flammable limit.

Jan 1, 1968

Several new techniques. which may be applied with advantage to the search for uranium are described. Scintillation type gamma spectrometers are now available for airborne', ground and borehole use. These can distinguish in a broad way between anomalies due to uranium, thorium and potassium. Gamma spectrometers based on semiconductor detectors now under development should be capable of much greater resolution. These should also make possible rapid, accurate and cheap radiometric analyses of samples containing uranium and/or thorium, whether in radioactive equilibrium or not. Another valuable prospecting aid, particularly in areas of tropical leaching, is systematic sampling of soil for radon content. Equip- ment for this purpose is currently available and it will be possible to extend the method when development of an alpha probe suitable for use in deeper holes is completed. Variations in the concentration of certain trace elements'in soil (e.g. mercury) also offer promise in the search for mineralized zones which may contain economic eon¦- centrations of uranium.

Jan 1, 1968

By Norman M. Junk

Following the wide-spread acceptance of ANFO as a useful, low cost blasting agent, studies have been made to adequately describe the physical and explosive properties of this material (1). As the quality of the AN blasting prill improved, reliability and sensitivity to initiation were greatly increased and many methods of priming were chosen from the standpoint of economics with little appreciation for the need to initiate so as to obtain the most efficient detonation. Under certain conditions, ANFO could be initiated with primers no more powerful than a No. 8 blasting cap (2). Research on primers for ANFO followed and it was demonstrated that this blasting agent was subject to extreme transient velocities upon initiation with wide variations in energy output depending upon the nature of the primer. For these reasons it was shown that powerful priming was economically justified (3). These studies helped to define the properties of an effective primer and the guides for its efficient use. In the vast surface coal mining industry, technological advances in earth moving equipment were paralleled by the development of larger and larger borehole drills (4). Even though ANM) was the major blasting agent used in this industry, investigations of priming techniques in these larger boreholes was almost non-existant. In 1962, Mr. Cleon Woolsey of Enos Coal Company disclosed to the industry that dramatic improvements in blasting production could be achieved with new priming and boostering methods (5). The research program at the Atlas laboratories was designed to explain these results and extend the study of initiation of ANFO with both high explosives and slurry explosives and to define the principles involved.

Jan 1, 1968

By Daniel N. Beshers, Ralph H. Condit

An expression for the diffusion coefficient of inlerstitial atoms in the bcc lattice is derived which takes account of jumps between tetrahedral and octahedral interstices. The results are applied to the case of carbon diffusion in iron to find values for jump frequencies of the types, octahedral-tetrahedral, tetra-hedral-tetrahedral, and tetrahedral-octahedral. ThERE has been renewed discussion1-5 concerning the mechanism of diffusion of interstitial atoms in the bcc lattice. This lattice has both octahedral and tetrahedral interstices, and it has been pointed out that the interstitial atoms may make jumps of the octahedral-octahedral type, hereafter called o-o, octahedral-tetrahedral, o-t, and tetrahedral-tetrahedral, t-t. Doubt has been cast on the applicability of snoek's8 model for internal friction to some interstitial migrations in bcc lattices wherein he proposed 0-0 jumps as the principal mechanism of migration. Also, the anomalous excess diffusion of carbon in iron at high temperatures4 has been ascribed to t-t jumps,2,3 even though the sites normally occupied are octahedral. In this paper an expression is derived for the diffusion coefficient, taking account of the three types of jump mentioned. The relationship of the coefficient to the corresponding internal friction relaxation time is found for the limiting case corresponding to Snoek's model. These results are applied to the case of carbon in iron. In Fig. 1, the structure is shown with the locations of the interstices. Each o site has four t site neighbors coplanar with it, and each t site lies halfway between two o sites. There are four t site first neighbors of a t site lying at the vertices of a tetrahedron. Let the average fraction of atoms occupying o sites and t sites be No and Nt, respectively. Since there are six o and twelve t interstices per unit cell having a lattice parameter, a, the concentration of interstitial atoms will It will be assumed that three types of jumps may be distinguished, t — t, t — o, o — t,for which the jump

Jan 1, 1968

Three major and two minor uranium deposits 'have been worked by open out mining since the discovery of ,the Rum Jungle field in 1949. Total production has been about 9679000 tons of uranium ore at 7;39 lb U308/ton and 4029000 tons of copper-uranium ore at 6.27 lb U308/ton and 2.7% Cu, with significant tonnages of base'metal ores. The deposits occur in or near black pyritic slates of the Lower Proterozoic Golden Dyke Formation, near the contact with the under- lying Coomalie Dolomite. The mineralization is probably younger than the grahite complexes in the area, and a structural-stratigraphic control of ore deposition is used as a basis for uranium exploration.\

Jan 1, 1968

By P. M. Johnson

A design for a laser-powered optical interferometer, using a specimen whose thermal expansion is to be measured as part of the optical system, was conceived and applied in a prototype dilatometer. The object of thin work was the development of an absolute dilatometer capable of use at elevated temperature, particularly above 1,000° C. The prototype has been operated at temperatures exceeding 1,510° C. Results obtained with this device agree within 2.5 percent with the published data for the coefficient of expansion of columbium.

Jan 1, 1968

By K. A. Johnson, F. H. Ellinger, C. C. Land

The Pu-La alloy systenz has been studied by thertnal, tnzcrographic, and X-ray diffraction methods. It is churacterized by a liquid miscibility gap, a maximum solubility of about 20 ut. pct PM in y lanthunum and 19 at. pct PI* in 0 lanthanum, very little soluibility of lanthanum in the plulonium allotropes, and the absence of intermediate phases. THE existence of immiscible liquids in the Pu-La system has been reported by Schonfeld.1 A tentative phase diagram based on the results of thermal-analysis experiments has been constructed by Poole et a1 2 This diagram shows a liquid immiscibility loop with a monotectic at 77 at. pct La and 846°C. 7 lanthanum is shown to dissolve 20 at. pct Pu and to decompose by an inverse peritectic reaction (y La = L , + p La) at about 82 at, pct La and 833°C. The ß lanthanum solvus was not determined, but the thermal work indicated a maximum solubility of 16 at. pct Pu in ß lanthanum. The present investigation has defined the solubility limits of plutonium in y lanthanum and 0 lanthanum, and, with the exception of minor discrepancies, has verified the results of Poole et al. 1) EXPERIMENTAL The electrolytic plutonium melting stocks were better than 99.9 wt pct pure, the main impurities being 90 ppm Fe and 50 ppm W. The lanthanum melting stocks, supplied by Research Chemicals and the Cerium Metals Corp., were about 99 wt pct pure, the main impurity detected by our spectrochemical analysis being 2000 ppm Fe. The components for each alloy button (-5 g) were weighed on an analytical balance and were melted together in a conventional arc furnace. If no significant weight loss occurred during melting, the as-weighed

Jan 1, 1968

By J. J. Demo

The effect of aluminum additions on the coating vale and corrosion resistance of Cr-Fe diffusiou coalings on a mild steel substvate has been studied. Aluminum additions up to 2 wt pct increase the chromium penetration rate while further additions retard it. The apparent cor$lict between these data and metallogyapkic ineasurements, which show a continuially increasing coaling thickness with aluminum addition, is discrissed. Compavisorz of corrosion resistance on the basis of equal thickness of tlre entire coating measured mnetal- ALTHOUGH ferrous metal articles are cheap and widely used, they are often quickly degraded by corrosion. To prevent or slow down the corrosion process, lographically is misleading; equal thickness of the cor-rosion-resistant portion of the coating is a bette.v basis of conzpavison. Inter difision coefFicients for Cr-Al-Fe coatings of different aluminum content have been detevmined and found to dary logarithmically when plotted againnst chromium concentvation. A general method of calculating diffusion profiles for different lrealment limes and surfuce coucentralions IS described. many types of coating are applied to steel.' Among these are diffusion coatings, formed by high-temperature diffusion of selected elements into the surface, which then becomes the coating Diffusion coatings are metallurgically bonded to the substrate and show a continuously varying concentration gradient from surface to substrate. Generally, these coatings have the advantage of adhering to the substrate upon deformation of the composite. Moreover, when chromium is one of the diffusion elements, a mild steel substrate

Jan 1, 1968

By Vernon A. Mrak

The Powder River Basin of northeast Wyoming was the first area in the state to receive attention during the early days of uranium exploration. Although the uranium occurrences are many and widespread, most of the known ore deposits are quite small and difficult to mine. As a result of this, detailed regional exploration in the Powder River Basin has been neglected. The uranium ore deposits occur in that part of the Wasatch Formation that is of earliest Eocene age, and they are scattered over an area of about 400 square miles. All uranium ore deposits are associated with red beds or altered sandstones within the Wasatch Formation. Uranium ore was first shipped from the region in 1953. Total production through June of 1965 is 506,257 tons of uranium ore containing 1,922,527 pounds of U3O8. The average grade of ore is about 0.19 per cent U3O8. The major producing area of the Powder River Basin is the Monument Hill district where about 91 per cent of the basin's total uranium ore has been mined. The source of uranium is presumed to have been the Oligocene, Miocene, and perhaps Pliocene tuffaceous rocks that once overlay the area. Joints, fractures, and permeable beds or zones were the passageways for the migration of uraniferous waters from the overlying beds to the Eocene host rocks.

Jan 1, 1968

By J. F. Smith, J. R. Ogren, N. J. Magnani

The uapor pressrcres of magnesium over binary alloys of magnesium with twelve of the yare-earth eletnetzts have been measured by the Knudsen effuion method in the temperature range 675° to 910°K. These vapor-pressure measurments were combined with data concerning the tevtrlitzul magnesium solubility and the vapor pressure of pure magnesinm to evaluale the standuvd free energies of pluase jormation. These free-etzergy values indicate that the CsCl structures of the heacy rave earths tend to be somewhat less stable than those of the light rare earths. This dif-]eying- behaviov covrelates with differences which have been obsevz~ed in other alloy systetns wherein a phuse appeurs, disappeavs, or changes crystal stvucture as the atomic number of the rare-earth com-ponent is changed. This behauior also appears to correlate with the struclurul rariations within the rare-earth elements themselves, and it is speculated that cariations in the spatial extent of the 4f orbitals are responsihle. STUDIES of the phase relationships and crystal structures in the binary systems between rare-earth metals (lanthanons) and magnesium are extensive but far from complete. However, the currently available information1-10 does produce a rather interesting pattern. This is illustrated in Table I. If one excludes europium and ytterbium from consideration because of their generally atypical behavior, it can be seen from the table that the phase relationships in the magnesium-rich regions show a distinctly different pattern for the lighter lanthanons as compared to the heavier lanthanons. For the lighter lanthanons, LnMg2 phases occur from lanthanum to gadolinium with the cubic MgCu2 structure, LnMg3 phases occur from lanthanum to terbium with the BiLi3 structure, and magnesium-rich phases occur from lanthanum to gadolinium with stoi-chiometries between Ln5Mg42 and LnMg12. In contrast, for the heavier lanthanons, those LnMg2 structures which have been examined have the hexagonal MgZn2 structure, LnMg3 phases have not been observed beyond terbium, and the magnesium-rich phases occur with the a manganese structure near a stoichiometry of Ln5MgZ4. The heavy lanthanon-magnesium systems thus appear to be analogous to the Y-Mg system""2 wherein YMg has the CsCl structure, YMg2 has the MgZn2 structure, and the region Y4Mgz5-Y5Mg24 has the a manganese structure, and no other intermediate phases are observed. Similarity in alloying behavior between yttrium and the heavy lanthanons occurs commonly, and on this basis it seems likely that LnMg2 phases will be found with the MgZn2 structure in the binary systems of dysprosium, thulium, and lutetium with magnesium when the appropriate investigations are made. In the case of the magnesium-rich phases of the lighter lanthanons, only the Ce-Mg phase relationships have been investigated thoroughly and in detail, and until similar investigations are made for the other systems there will remain questions as to which magnesium-rich stoichiometries represent equilibrium phases and what systematic variations occur in the sequence from lanthanum to gadolinium. Thus the data in Table I show that only the LnMg phases occur with the same crystallographic structure throughout the sequence from lanthanum to lutetium. It was speculated that the relative stability of these LnMg phases might vary from one lanthanon to the next in such a way as to presage the differences which occur among the more magnesium-rich lanthanon-magnesium phases. On this basis the present investigation of the thermodynamics of phase formation was Gndertaken for the LnMg phases. PROCEDURE AND RESULTS A generalized phase diagram for the lanthanon-rich portion of a lanthanon-magnesium alloy system is shown in Fig. 1 where ß represents a high-temperature bcc

Jan 1, 1968

By Thomas S. Bishop

From time to time the mining engineer will be faced with the necessity of having to make a haulage study to determine not only the most suitable method of hauling material but also the most effective and economical type of equipment to use for his particular operation. Specifically, this chapter outlines a general description of various types of haulage units and their components, guidelines on the selection of equipment, material both operational and cost wise to be accumulated, discussions on the various factors involved in the development of the estimated production and cost analysis, examples of the above, and the necessary reference material. This material and examples are given in such a form as to permit the engineer to proceed on almost a step-by-step basis in the determination of the applicable haul speeds and other related portions of the haul cycle and resulting number of trips per hour. In recent years, the analytical methods used for the application of the various haulage units have undergone a considerable change. Several vehicle manufacturers and a few of the mining companies employ electronic digital computers to speed up the calculations and improve the accuracy of production estimating. The haulage computer program simulates the travel of the vehicle over the described haul roads by calculating incremental velocities, travel times, and travel distances from the known torque vs. speed characteristics of the vehicle. This is, in a sense, a numerical integration of the vehicle's performance and, of course, varies for each and every application. These travel times are then combined with easily estimated fixed times such as loading, turning and dumping, spotting, and any indicated delay times, resulting in a total cycle time for the vehicle. Usually, the travel times comprise the major portion of the time cycle; therefore, the concise computerized calculations eliminate much of the guess work in estimating vehicle productivity. Field studies have correlated this analysis

Jan 1, 1968

By Robert E. Green, Edmund G. Henneke

Expressions are derived for the orientation factors associated with dislocation damping due to dislocation motion in the basal slip plane. The results of the calculation of these factors for zinc crystals aye pvesepzted and the relevance of these results to ultvasonic-attenuation measuvements is discussed. In this paper expressions are derived for the orientation factors associated with damping of sound waves due to dislocation motion in the basal slip plane of hexagonal crystals. For zinc crystals, the orientation factors for dislocation motion in one slip direction only, as well as for simultaneous motion in all three basal slip directions, have been calculated at 1-deg intervals. The results of these calculations are presented in the form of contour diagrams in a sector of a standard polar coordinate graph. The calculations have been carried out for both the traveling- and the standing-wave conditions. The relevance of these results to ultra sonic-attenuation measurements is discussed. Associated with the calculation of the orientation factors, the modes of elastic-wave calculation were also evaluated, according to the procedure previously employed by Hinton and Green.' The results of these calculations are not presented here since similar results have been reported earlier by Mus-grave.2 However, it should be mentioned that, although the qualitative features of Musgrave's results are preserved, the quantitative values are somewhat altered since different values for the elastic constants of zinc were used. ORIENTATION FACTORS It is convenient to refer to three different sets of coordinate axes, Fig. 1, in the following calculations. First, there are the Miller-Bravais axes which are used in describing the Miller-Bravais indices of planes and directions in a hexagonal crystal. These axes are denoted in the conventional manner by a,, a,, a,, and c. The second set of axes used is a rectangular Cartesian coordinate system located as shown in Fig. 1. Note that the x axis coincides with the close-packed direction al [2110], the z axis coincides with the c axis [0001], and the y axis is orthogonal to these two lying in the [0110 ] direction. Finally, a form of Eulerian angles is used to locate the position of the specimen axis. The angle between the specimen axis and the c axis is denoted by 0 and the angle between the projection of the specimen axis on the basal plane and the a, direction is denoted by ø. The majority of observations on plastic deformation of metal crystals indicates that such deformation is caused by the motion of dislocations on a limited number of crystalline planes and in a close-packed direction. In crystals with hexagonal symmetry the most prominent slip plane is the basal plane (0001) and the slip directiops- are one of the close-packed directions, [2110], [ 12101, or [ 1120]. To properly set the stage for the following work, several points must be clarified. First, we want to consider the contribution to the attenuation of elastic waves by dislocations only. While the Granato-Lucke, model for dislocation damping is presently the one most quoted, it is not necessary to refer the present work to it. The only assumption that need be made is that the motion of dislocations absorbs energy from the elastic wave and therefore attenuates it. It is immaterial here how this energy absorption occurs. However, because dislocations have been observed to move most freely on the (0001) plane for hexagonal crystals undergoing plastic deformation, it will be assumed that it is the dislocation motion on this plane which attributes to the observed attenuation. The basic orientation factor, Ok, is essentially the same as that used by Green and Hinton for fee crystals,4 defined by the equation

Jan 1, 1968

Ammonium nitrate-fuel oil (ANFO) explosives are unstable in hot, reactive sulphide-rich ground at Mount Isa. Under certain conditions associated with background heat, moisture, and chemical impurities from natural oxidation, ANFO composites in contact with hot ground disproportionate and the ammonium nitrate can undergo rapid exothermic reactions with sulphide.Reactions can occur in confined charges from prolonged contact with reactive sulphides, or by contamination with sulphide in loading. Partial interaction can result in misfires or premature detonation. Spilt, scattered and unpropagated explosive will undergo further reaction in sulphide-rich environments. ANFO-sulphide interaction is invariably exothermic and causes an irreversible chemical transformation of the ore.The heat generated during reaction may be dissipated, heating the environment, or rapidly accumulated to yield hot spots or areas in excess of 400°C. These can result in forced ignition of bulk sulphide and sustained combustion.Thermal analysis was used to define the critical conditions for ANFO-sulphide interaction and sulphide combustion.The occurrence of incandescent ore is attributed to the thermal interaction between exothermic hydrolysis oxidation, ANFO-sulphide, and combustion processes.Chemical agents and control methods have been developed to prevent ANFO-induced oxidation and combustion.

Jan 1, 1968

By Paul F. Thiele

The mining industry of Georgia, while not as large as in some other states, is still an important part of the economy. Total value of mineral production in 1966 was $148.6 million.l/ Clays and stone produced the most income, Other minerals included sand and gravel, iron ore, mica, talc, barite, bauxite, cement, feldspar, kyanite, peat, and rare-earth metals, titanium and zircon concentrates. Georgia ranks first among the states in production of kaolin, second in fuller's earth and rare-earth concentrates, third in bauxite and kyanite, fourth in barite and ilmenite, and fifth in feldspar. It is quite likely that phosphates will one day be mined in the south eastern part: of the state, and that alumina will be produced from the extensive kaolin deposits in the central part of the state.

Jan 1, 1968

By L. H. Cadoff, L. M. Adelsberg

The layer growth method has been used to investigate the reaction kinetics of liquid titanium and hafnium with carbon and the [liq] - [liq + TiC] and [liq] - [liq + HfC] phase boundaries at temperatures above 1800°C. The equipment and experimental procedures used in this investigation are basically identical to those described in an earlier paper' on the Zr-C reaction. Temperature control, however, was improved significantly by connecting a Latronics Colo-Ratio automatic pyrometer and a controller to the power source. The subsequent temperature variations were ±10°C; previously ±20°C was obtained using manual controls. The absolute accuracy of the pyrometer, however, must be considered to be only ±40°C.* The spectrographic analyses of the materials used in this study are listed in Table I. The isothermal reactions of titanium (1800° to 2700°C) and hafnium (2300" to 3000°C) with carbon (graphite crucibles) resulted in the formation of carbon-saturated liquid metal and layers of Tic and HfC, respectively. The thicknesses of the carbide layers, determined from metallographic measurements at 100 times, as a function of carburization time and temperature are given in Figs. 1 and 2. At each temperature, parabolic growth behavior for these reactions was observed and could be expressed as x2 =Kpt, where X is scale thickness (corrected for heating and coolingL), Kp the parabolic growth constant, and t the isothermal carburization time. Values of Kp as a function of temperature for the carbides are shown in Fig. 3 and listed in Table 11. The growth constants are expressible as: kpTiC = 0.2 exp(-61,800/RT) sq cm per sec for Tic and Kp HfC = 2.62 exp(-95,300/RT) sq cm per sec for HfC. The liquidus phase boundaries were determined from metal samples treated in graphite crucibles for different times ranging from 4 to 100 min at each of the temperatures indicated in Table 11. Metallographic examination revealed that the carbide precipitates were distributed uniformly throughout the frozen metal matrices. This is attributed to the rapid cooling rates (800°C per min) and the small difference in density between the precipitated carbide and the liquid metal.

Jan 1, 1968

By H. Evans, L. A. Hunt

The raw materials used in the blast furnaces at the Geneva Works of U.S. Steel Corp. have a high degree of variability in size-consist and chemical content. To overcome the problems caused by the use of highly variable raw materials in the blast-furnace operation, large blending piles are used. An investigation of the blending system showed that variability was significantly reduced by the use of these blending piles. This paper describes the blending system, the method used to evaluate the effect of the blending system, and the results of the investigation. The remarkable improvement in blast-furnace performance since World War II has been in large measure due to the use of beneficiated burdens to reduce the variation of both chemical analysis and size consist. This practice allows the operator better control of his blast furnace, enabling him to operate more economically and to produce chemically uniform hot metal. Planning for uniformity usually begins during mining by extracting ore from several locations within a pit to produce a final product with a specified analysis. Another approach is to stockpile ores having widely varying analyses in individual piles and then drawing the required amounts from each stockpile to provide a blend with a predetermined analysis. A further improvement in blending procedures is to take ores from several sources, bedding them horizontally in layers and reclaiming by vertical slicing from the blended pile. The last procedure, when properly executed, is one of the best methods for achieving maximum uniformity with highly variable ores. U.S. Steel Corp.'s Geneva Works initially obtained iron ore for their blast furnaces from the Cedar City area of southern Utah. These ores were formed primarily by the replacement of limestone and siltstone formations with solutions containing iron and several other elements. The original iron content of the ores in the ground varied from a high of 70% to practically zero with a minimum acceptable iron content for shipping of 37%. Substantial amounts of silica, calcium, magnesium and alumina were found in the ores along with minor amounts of copper, lead, zinc, nickel, titanium, manganese, phosphorus and sulfur which were sometimes present in detrimental amounts. Iron-to-silica ratios varied considerably throughout

Jan 1, 1968

Jan 1, 1968

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions3 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1968

By Arthur F. Daily

8.5-1. Bucket Line Dredge. INTRODUCTION. The modern bucket-line dredge for mining placer deposits is a combined floating excavating machine and a gravity concentration system. Material is excavated at the forward end by the buckets, elevated, washed and screened, concentrated for recovery of valuable mineral, and discharged off the stern as coarse and small fractions. The end product is a concentrate consisting either of the valuable mineral(s) and associated heavy minerals, which are taken to a treatment plant on shore; or in the case of gold, a clean amalgam ready for retorting. The bucket-line dredge may be adapted for purposes other than mining for valuable mineral by installing, in lieu of a concentrating system, machinery for pumping all of the solids ashore in a pulp, or for producing washed gravel in selected size fractions of which all or a selected fraction is pumped to disposal areas on shore or into side barges. The two principal types of bucket-line dredges designed for mining are: 1) those having an inclined belt conveyor stacker to discharge the coarse fraction of washed tailing well astern of the hull, and sluices to discharge the sand fraction (Fig. 8.5-1), and 2) those having only sluices for discharge of all tailing astern. Use of the latter type has been confined, with few exceptions, to mining cassiterite-bearing deposits in Malaysia and at sea off Indonesia. Small dredges having only flumes for washing and concentrating all material dug by the buckets have been used for mining shallow stream valley deposits. GENERAL ARRANGEMENT. The general arrangement of a modern bucket-line dredge for mining tin, with a primary concentrating plant on board, is shown in Fig. 8.5-2. The hull and superstructure of most dredges are fabricated of structural steel; wood also has been used for both small and large dredges with complete satisfaction. All-riveted or partially welded unit hulls have been widely used and are desirable for exceptionally severe service. The hull

Jan 1, 1968

By Paul F. Kerr

The uranium-producing areas near Marysvale, Utah provide an unusual group of veins and replacement deposits associated with a Pliocene-Oligocene intrusive and extrusive igneous complex. Aside from several scattered occurrences in older volcanics, uranium-bearing veins occur in intrusive quartz monzonite or granite and in nearby rhyolite. The veins in general trend within a few degrees of N55-65°E, are more or less vertical, and are found along the western margins of a quartz monzonite intrusive. The replacement deposits are found in rhyolite intrusives and also in the lower portions of rhyolite flows close to places where veins forming solutions rising through quartz monzonite came into contact with the rhyolite. At least 14 veins have been mined since uranium mining operations began at Marysvale some 16 years ago, while ore has been extracted through about 10 miles of underground workings. The active mmmg area is approximately 3000 feet long and in the central portion 1500 feet wide. Ores have been found over a vertical spread of almost 2000 feet, between the highest occurrence on Jungfrau Hill ( ca. 7200 feet) and the deepest discovery of ore in a drill hole near the Prospector Mine (ca. 5200 feet). Under existing mining and marketing conditions, mining along the veins in the main area appears to have reached an economic limit at about 500-600 feet below the surface. However, orebodies in the rhyolite and in the upper portions of veins close to the rhyolite are subject to active mining. Isotopic dates indicate that the uraninitebearing veins and replacements are late Miocene or Pliocene (ca. 10-13 m.y.), the rhyolite is Miocene (avg. 17.5 m.y.), and the quartz monzonite and granite intrusives are late Oligocene (23.6 to 26.0 m.y.). The older Bullion Canyon Volcanic Series which encircles the area is Oligocene (28 to 31.1 m.y.). Two generations of alteration occur: ( 1) Earlier alunitic veins and replacement bodies are found in the Bullion Canyon Volcanic Series, none of which have produced uranium; (2) Later argillic alteration associated with the introduction of uranium is found along veins, replacing glassy rhyolite dikes and replacing phases of the rhyolite.

Jan 1, 1968