Search Documents

By G. Y. Chin, W. L. Mammel

The problem of selection of the active slip systems for a crystal undergoing an arbitrary strain has been analyzed by Taylor and by Bishop and Hill. The Taylor analysis is based on a principle of' virtual work, and involves finding, among numerous cotnbinalions of slip systems that satisfy the imposed strain, the combination in which the sum of the glide shears is a minimum. Previously, Taylor has treated the case of axisymmetric flow when slip occurs on (111)(110) (or {110)(111)) systems only. His analysis has now been extended by computer methods to the cases of slip on {112}(111) and {123)(111) systerns and of mixed slip on {110), {1 12), and (123) planes with a common (111) slip direction, all of which are important in the deformation of bcc crystals. The results are computer-plotted as contours of the ratio of the floe strength to the critical resolved slzea-r stress for slip, for axial orientations distributed throughout the standard stereographic triangle. Implications of the computer results to texture develop,merit, texture hardening, and dislocation theories oj work hardening are discussed. WhEN a single crystal is extended in the usual tension test, the lateral dimensions can change relatively freely. In this case, the glide shear produced by slip on a single slip system is sufficient to accommodate the (tensile) deformation. Since slip is governed by a critical resolved shear stress law (the Schmid law'), the single active slip system is one for which the stress, resolved on the slip plane and in the slip direction, is the highest among the several equivalent slip systems. This amounts to saying that a value M = U/t = y/~ is a minimum among the equivalent systems, where M is the inverse of the familiar Schmid factor (a and E refer to tensile stress and strain, and T and y refer to resolved shear stress and shear strain). A grain embedded in a polycrystalline aggregate, on the other hand, cannot freely change its shape due to constraint from its neighbors. In this case, slip from five independent slip systems (to accommodate five independent strains) is generally required.' Based on the principle of virtual work and assuming that the critical resolved shear stress for slip is the same for all systems, Taylor hypothesized that, among all combinations of (five) slip systems which are capable of accommodating the imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Again, this is equivalent to saying that the value of M = CjlyjI/ is a minimum, in analogy to the single slip case. Taylor aminimum,analyzed the case of {111)(110) slip for fcc metals, and applied the analysis to crystals undergoing axisymmetric flow, that is, the same macroscopic shape change as the poly crystalline aggregate under uniaxial tension (or compression). For the twelve equivalent {111}( 110) slip systems, there are 384 independent combinations of selecting five systems to satisfy the five independent linear equations of imposed strain.4 Taylor calculated the value of M for each combination* and obtained the active com- *A number of the independent combinations were omitted from consideration in Taylor's original work (see Ref. 5). bination (minimum M) for a number of axial orientations distributed throughout the standard stereographic triangle. Later work by Bishop and Hill*'8 showed that Taylor's least-shear hypothesis was equivalent to a maximum work principle which they advanced. Using the simplified Bishop and Hill method for {111)(110) slip, Hosford and Backofen' obtained detailed contours of constant minimum M for the same axisymmetric flow case. In contrast to {111}(110) slip in fcc metals, slip in bcc metals is generally described as occurring on {ll~)(lll), {112)(111), {123) (111) systems as well as mixed slip composed of all three. Since the direction cosines of the slip plane normal and the slip direction enter as a product in the Taylor analysis, the Taylor solutions of ,M for {110)(111) slip are identical to those for { 111} 110) slip. The other three cases of slip, however, have not been solved. In view of the numerous combinations of slip systems involved in the calculations, the Taylor analysis is clearly oriented toward computerized solutions. THE TAYLOR ANALYSIS In order to obtain the active combination of (five) slip systems by solving for the minimum value of M = we first express the (small) strain components E,, with respect to the cubic axes 1, 2, 3 ([loo], [010], [001], respectively) of the crystal, in terms of the sum of the glide shears yj from slip systems j: where n, and n,j refer to direction cosines of the slip plane normal, and dri and dsi to direction cosines of the slip direction, of slip system j, all referred to the cubic axes. In practice, the strain components are given with respect to the specimen axes X, y, 2. These components are readily converted to ers through the tensor transformation where irk and 1,~ are the direction cosines between the two sets of coordinate axes.

Jan 1, 1968

By W. A. Tiller, W. C. Johnston

A high-temperature electromagnetic stirrer is described in which heating and stirring are accomplished by independently controlled power sources. The appavatus is suitable lor use at temperatures up to 1700°C in a variety of ambient atmospheres. Some typical examples of the homogenizatimz capabilities of the system are given. THERE are few processes in solidification that are not markedly affected by motion in the melt during freezing. In many instances, the mechanisms are diffusion-controlled, and the transport in the melt may be greatly accelerated by deliberately stirring the melt. In zone-refining, stirring1 assists the removal of rejected impurities from the interface, so the process proceeds at a faster rate. The transition from a planar to a cellular interface is caused by constitutional undercooling in the melt ahead of the interface: and stirring delays its onset. Stirring is valuable for homogenization of melts: and chemical reaction with sluggish kinetics may be accelerated. Finally, it has been observed that grain refinement is related to motion in the melt. Fine grain castings are usually produced by the addition of catalysts to the -melt,' catalysts which are thought to act simply as hetereogeneous nucleation centers. Even here motion is important. Richards and Rostoker 5 applied ultrasonic vibration to a solidifying A1-Cu alloy which had been innoculated with a catalyst and found that the grain diameter fell linearly with the amplitude, the peak acceleration and the power input to the melt from the transducer. Finally, mechanical and electrical stirring alone have been used to generate a fine-grained structure.6,7 Johnston ef a1.' have carried out a series of systematic investigations of grain refinement by electromagnetic stirring in a number of low melting point alloys. They found, for example, that the number of grains per unit volume in Pb-Sn alloys could be increased several orders of magnitude by stirring an undercooled melt at the moment of recalescence. In general, a relation AT .H = constant prevailed for a given grain size, where AT was the undercooling of the melt and H the field strength. In more recent work, deliberate homogeneous nucleation of slightly undercooled melts established that the mechanism of refinement must be one involving crystal fragmentation and subsequent multiplication, rather than a "shower" of nuclei effect.9 It is the purpose of this note to describe a stirring device suitable for use up to 1700°C. At low temperatures mechanical stirring and direct-current methods are feasible, but at high temperatures the problem of a protective atmosphere and of electrode corrosion rules out such procedures. The most convenient method for high temperatures is to use externally generated ac fields for both stirring and heating. With rf induction heating alone, considerable stirring and agitation can be achieved, but in general the penetration of field into the melt is small, and the stirring cannot be controlled independently of the heating. In the present experiments, separate power sources of different frequencies for heating and for stirring were used. A susceptor design was chosen so that the 450 kc rf heating field was completely absorbed in the susceptor. The stirring frequency, 400 cps, hereafter called the af field, was chosen so that a high penetration of the melt proper was achieved. EXPERIMENTAL APPARATUS The apparatus, Fig. 1, consists of a quartz tube and end plates, surrounded by an rf induction coil and six equally spaced af stirring coils, four of which are shown in full and a fifth in section. Each af stirring coil is a transformer of which the secondary is a single-turn water-cooled copper loop and the primary is composed of two 10 amp-117 v Variac cores as shown. These cores are cooled by forced air, as each of the six pairs will carry maximum currents of 15 amp for short periods. Each set of Variac windings are connected in series, but opposite sets are connected in parallel with a three-phase 400 cps 400-v source. By properly phasing the coils in this way, a rotating field is produced. Capacitors C1, C2, and C3 in Fig. 2 are used to match this inductive load to the generator. Fig. 3 shows a cutaway view of the quartz tube. The sample (1 in. diam by 1 in. high) is placed in a tapered alumina crucible. An axial W-26 pct Re thermocouple, enclosed by a protection tube, is provided. The cruci-

Jan 1, 1968

By Roshan B. Bhappu

Although the economic importance of recovering copper by leaching of mine work dumps from open-pit operations has been realized for some time, serious attempts to understand and to improve such operations through scientific research has been made only in recent years. This progress report covers the results of chemical, physical, and biological studies pertaining to the dump leaching process and discusses salient features and parameters that may be helpful in improving such operations.

Jan 1, 1968

By W. A. Backofen, D. Lee, F. S. Jabara

THE empirical character of plasticity analysis insures a continuing need for measurements of the yield surfaces of anisotropic materials. Recently, Wheeler and Ireland (W-I) proposed that an octahedral yield locus could be constructed on the basis of six Knoop hardness indentations. Such simplicity would have obvious appeal, if it led to consistently dependable results. In other recent work, a much more straightforward (and more tedious) method of measurement was used to establish all quadrants of the plane-stress yield loci for two substantially anisotropic titanium alloys.2,3 The same materials have since been reex-amined by the W-I method with results being reported here. A full description of the stress state under a Knoop indentor would be complex. In principle, however, this can be avoided in relating the hardness number to a plane-stress yield locus, by the expedient of superimposing the appropriate hydrostatic component on that state of stress. Six possible orientations of in-dentor on orthogonal (symmetry) planes, along (principal) coordinate directions, are illustrated in Fig. 1(0). Pictured in Fig. l(b) are normal-stress components nominally associated with indentation n: o2(H), directly proportional to the Khn in this case, together with By overlaying a hydrostatic tension, ah, that in general is equal to the stress state around the indentation is reduced to one of plane stress in the x-y plane for which the stress ratio is a The key step in the W-I yield-locus construction is to represent the Khn for any indentor orientation as a vector quantity on the octahedral plane. In the plotting, the vector is given as deviatoric stress components along the principal axes in the ratio , where represents the direction of the minor (width) diagonal and 1 that of the major (length) diagonal. There is no attempt by W-I to justify the 7/1, although it might be supposed that the value originates in the usual ratio of major to minor diagonals in a Knoop indentation of about 7/1. If that were its origin, the link to the deviatoric stress ratio would presumably be made by first taking 7/1 and then turning to the Levy-Mises equation for isotropic material: Interpreted in this way, the W-1 approach seems arbitrary and even contradictory. Yet it would still be favored by two circumstances: the deformation under a Knoop indentor approaches plane strain: when dcw/del =a; and the shape of the locus where plane strain is represented is not overly sensitive either to the exact value of dc,/dcl or to the degree of anisotropy, within a rather wide range of both variables. The second point is illustrated below, after a few additional comments on applying hardness

Jan 1, 1968

By Thomas A. Steven

Most mineralized areas in the central San Juan Mountains, Colorado, are associated with the youngest subsidence structures in a large volcanic cauldron complex that formed concurrently with eruption of the surrounding ash-flow field. Two local types have been recognized: (1) fissure-vein deposits along faults characterized by relatively late movement, and (2) hydrothermally altered and mineralized areas associated with postsubsidence Fisher Quartz Latite centers. The first type has provided most production in the past; the potential of the second type has yet to be adequately tested.

Jan 1, 1968

By W. A. Tiller, S. O’Hara

Grain refinement in stirred melts has previously been shown to arise from dendrite segmentation. The present work discusses experiments capable of distinguishing between remelting and mechanical effects which result from fluid motion. Nucleation of still un-dercooled Sn-1 pct Pb melts with a single-crystal seed shows that the grain size of the resulting ingots decreases as the undercooling at nucleation increases up to about 1Z0C, then increases again for larger undercoolings. Pure melts exhibit little refinement as a result of nucleation at any undercooling up to 12°C. The presence of fluid motion gives rise to grain multiplication in pure melts, but the magnitude of this effect is partly obscured by solid-state pain growth. The results indicate that two grain-multiplication pvocesses can operate, one which involves dendrite remelt ing, and another associated with fluid motion. Small ingot experiments indicated that an equiaxed transition can be caused by fluid motion. THE presence of forced convection during recales-cence of undercooled Sn-1.3 pct Pb melts has been shown to give rise to extensive grain refinement during solidification of small ingots of this alloy.''2 In Ref. 2, this refining was shown to result entirely from dendrite fragmentation and not from any nucleation mechanism. The purpose of the present work is to establish what processes lead to dendrite segmentation. Experiments were therefore carried out to determine the resulting structure of both pure tin and Sn-1 pct Pb melts, nucleated at various undercoolings by single-crystal seeds in the absence of forced or natural convection. By comparing the information obtained from these experiments with the results of Refs. 1 and 2, the effects of fluid motion on the ingot structure, and the details of the segmentation mechanisms, should become clear. The results of these experiments should also be helpful in understanding the solidification structures of larger ingots since natural convection, which is known to play an important role in determining ingot structure13 differs only in degree from the fluid-motion effects studied here. I) EXPERIMENTAL PROCEDURE The apparatus shown in Fig. 1 was constructed to permit controlled nucleation of stirred or unstirred supercooled melts using a seed oriented in the tin dendrite growth direction. Because the melts, in all cases, were capable of larger supercoolings than the one used in each experiment, the structure observed always resulted from a single nucleation event at the surface. The sequential procedure was as follows: Tin was melted under purified hydrogen and the oxide removed at a temperature of 450°C . Electromagnetic stirring was then used to clear the surface completely and during this time the guide tube was lowered underneath the melt surface. A pointed Czochralski-like crystal was then propagated from a specially prepared tin dendrite seed4 inside the guide tube while the temperature of the bulk melt was held just above the melting point, ensuring a perfectly clean seed which was epitaxial with the original dendrite. The dendrite and epitaxial seed, still in the guide tube, were withdrawn from the melt which, in turn, was undercooled to 2C° below the temperature at which the nucleation experiment was to be performed. The melt was held there for several minutes, both in stirred and in still-melt experiments. The temperature was next raised to the required value and the melt nucleated by the carrot seed inside the guide tube, the heater power being shut off just after nucleation. In experiments where quenching after nucleation was required, a high-density graphite crucible was used, but otherwise the procedure was as described above. The temperature gradient in the melt before nucleation was kept below 1C° per cm by carrying the experiment out just below the center of the heater shown in Fig. 1.

Jan 1, 1968

By Kenneth J. Miller

To determine the effectiveness of the many new flocculants available to the coal industry 20 of these reagents were evaluated treating slurry feeds to four refuse thickeners. Settling rates and supernatant liquid clarities were determined for each of the flocculants on the four slurries, and zeta potential measurements of the slurry solids were made. The test results showed that the flocculants provided comparable results when judged categorically as anionic, nonionic, or cattonic. It was also apparent that control of zeta potential insures maximum benefit from a flocculant.

Jan 1, 1968

By Arthur F. Daily

13.5-1. Placer Deposits-Definitions. Placers are defined for this chapter as unconsolidated deposits of detrital material containing valuable mineral, and placer mining is defined as surface exploitation of placer deposits. Unconsolidated marine deposits containing industrial minerals, such as the very large pebble phosphate beds in Florida, pelletal phosphate beds in the Sechura Desert in northwestern Peru, oyster shell beds occurring at many places, and nodules resting in the sea floor, are not classed herein as placer deposits, though methods commonly used for mining placers may be employed for their exploitation. The natural processes that may form placers range from chemical weathering to stream, marine, and wind action, and combinations thereof, resulting in some degree of concentration of valuable mineral. One or more cycles of erosion and deposition may have occured. In relation to mining, placers include unconsolidated barren or near-barren overburden and underlying weathered bedrock. Placers of any origin subsequently may become drowned by the sea and then partly or entirely covered by marine deposits; or they may become covered with alluvium, eolian deposits, or lava. The mining of placer deposits for valuable mineral content usually is followed immediately by primary concentration using wet (rarely dry) gravity methods, succeeded by secondary concentration employing both gravity and other methods. 13.5-2. Classification of Placers. A fundamental classification of placers according to genetic types follows; some degree of concentration occurs during formation of all except saprolite and some moraines. 1. Saprolite and residual placers, consisting of mineralized rock decomposed in situ principally by chemical weathering; respectively either without change in volume, or slumped because of dissolution of some constitutent.

Jan 1, 1968

By J. M. Singer

Flame propagation of lower limit hybrid coal dust-methane-air mixtures in vertical and horizontal flame ducts of 15.2 cm id and 1.8 m length has been investigated to provide information bearing on safety in mines. Fuel concentrations at lower limits of flame propagation and equivalences of coal dust and methane are much higher for continuing flame propagation than for short-span flame propagation in the vicinity of an "overdriving" ignition source. As the energy of the ignition source was increased, the flame speed and the distance of flame propagation from the ignition source increased, whereas the total fuel concentration at the lower limit decreased.

Jan 1, 1968

By R. L. Loofbourow

The Sunro Copper Mine is near the south coast of Vancouver Island about 35 miles west of Victoria. Failure of the roof of a large open stope let a good sized mountain stream into the mine. Broken are, boulders and sand were washed into the underground mill and out through a 7 800-foot adit. The adit became plugged; water burst out an a ridge above the adit, washing out the portal and o trestle by which it was reached, Rock and ore are strong but several systems of steep, pronounced but generally tight fractures are found on and parallel to the walls of the orebody. The stope was started from a slusher drift 390 feet below the bed of the River and brought up to an elevation 155 feet below the River by blasting vertical and horizontal rings of longholes in the nearly vertical orebody. Mining was stopped there and five months were given to grouting and bolting the pillar under the bed of the River, During this time and for several months thereafter sloughing increased the width, length and height of the stope. At the last known observation the stope was 77 to 96 feet wide, 185 feet long and the highest point of the domed back was only 55 feet below the River. The flooding took no lives. In other respects, however, it might be difficult to find in mining lore o more savage example of the application of "Murphy's Laws".

Jan 1, 1968

By C. J. Hall

This paper presents a basic motive column analysis of natural ventilation and shaft resistance, using the density depth diagram. The method makes use of tables showing the state of the air as determined by thermodynamic analysis. Several theoretical examples are given.

Jan 1, 1968

By M. Jack Snyder

The problem of effective utilization of fly ash has been given wide attention for a number of years. Although the effort devoted to the problem has led to some applications of demonstrated usefulness, the full utilization of fly ash has been held back by lack of concerted research and development activity, by lack of effective dissemination to potential users of fly ash of the knowledge that is available from laboratory and field studies, and by the obvious variability of the product. Because of the variability in fly ash from one power plant to another and from time-to-time in the same plant, specifications have been set up defining compositional or property limits within which a fly ash must fall to be used in certain applications. This paper discusses the bases for such specifications and examines them in the light of recent research on the characterization of fly ash. Other limitations and restrictions on the use of fly ash and what is being done to overcome them are also discussed.

Jan 1, 1968

By E. M. Kalar, I. Iwasaki, J. D. Zetterstrom

Several methods of removing fatty acid coatings from iron ore flotation concentrates were tested both on a Mesabi oxidized iron ore and on a magnetic taconite concentrate, and their effects on the duplex flotation process and on pelletizing were compared. Either acid or alkali alone could not remove the coatings, but a combination of such reagents as lime and quebracho, calcium chloride and pyrophosphate, or sulfuric acid and an organic acid (oxalic, malonic, or citric acid) was quite effective. The use of activated carbon was found to be particularly promising. The removal of fatty acid coatings from iron ores is of much practical interest when a pelletizing process is being considered for a concentrate floated with a fatty acid collector or when a duplex flotation process is being considered for upgrading an oxidized iron ore. A duplex flotation process is a fatty acid flotation of iron minerals followed by an amine flotation of the siliceous gangue from the rougher iron concentrate. Such a process is being used in the Florida phosphate fields.' Although in northern Michigan mills fatty acid flotation concentrates have been pelletized successfully, at other locations fatty acid coatings on iron flotation concentrates have proved so undesirable in the agglomeration operation that other methods of concentration had to be sought.' Since fatty acid coatings cannot be removed as readily with a simple acid or alkali treatment from iron oxide surfaces as from Florida phosphates, a combination of reagents, such as lime and quebracho,3 lime and alkali phosphate,4 or sulfuric acid and oxalic acid,' has been proposed. It was also thought that activated carbon might be effective in removing fatty acid coatings due to its high adsorptive capacity. Activated carbon, with its enormous surface per unit of volume, is well known for its exceptional efficiency in removing organic pollutants from industrial effluents. This article presents the practical aspects of the above methods when they are applied to the duplex flotation process and to the pelletizing of iron flotation concentrates. The article also includes a preliminary investigation of the common parameters involved in the depressant activity of the reagents. EXPERIMENTAL WORK Initially, the experimental work was directed towards the optimization of each method for the removal of hydrophobic coatings from iron oxide surfaces floated with fatty acids. Subsequently, the methods thus optimized were tested in the duplex flotation process with an oxidized iron ore and in the pelletizing process with a magnetic taconite concentrate. Preliminary Flotation Tests: Although the three types of chemical treatment reported in the literature were briefly investigated for the purpose of comparison, major emphasis was placed during the preliminary flotation tests on the use of activated carbon because it was thought to have certain advantages over the chemical methods. LIME AND QUEBRACHO - To obtain a flotation concentrate for optimizing the lime and quebracho method of fatty acid removal, the magnetic taconite concentrate was used. The concentrate had a size consist of 90% passing 325 mesh and analyzed 64.5% iron. After a few preliminary tests the fatty acid flotation procedure with the magnetic taconite concentrate was standardized as follows. A 1200-g sample of the magnetic concentrate was pulped in a Fagergren laboratoy flotation cell to 40% solids, conditioned with 0.5 lb of soda ash per ton for 2 min, and then further conditioned with 1.0 lb of Acintol FA-2 per ton for 2 min. After 5 min of flotation, recovery was nearly complete, averaging 98.6% of the weight and 98.7% of the iron. The cell product, which amounted to 1.4% by weight and analyzed 63.2% iron, consisted mainly of relatively coarse middling particles. Since the repro-ducibility of the flotation concentrates produced by this procedure was vey high, the same procedure was used to prepare fatty acid concentrates for each of the six tests of the lime and quebracho method. To test the removal of the fatty acid from the magnetite surfaces by the lime and quebracho method, a fatty acid froth product was returned to the flotation cell, repulped by 30 sec of agitation, and then con-

Jan 1, 1968

By Davis M. Lapham

Ore bodies at Cornwall, Pennsylvania, have been mined since 1742 principally for iron from magnetite, but also for copper (in chalcopyrite), silver (in chalcopyrite), gold (in chalcopyrite), cobalt (in pyrite), sulfur, and crushed limestone aggregate. Metallization occurs as a limestone replacement above the essentially conformable, south dipping portion of a discordant saucershaped diabase sheet. Pre-Triassic and Triassic faulting have emplaced host Cambrian limestone and two Ordovician(?) hornfels units, now for the most part resting above diabase. Thermal metamorphism of carbonate-bearing country rocks largely to calc-silicates, is ubiquitous. Metasomatism, particularly of potassium, is unique to ore zones. Associated magnetite- actinolite mineralization replaces, in a preferential sequence, all earlier metamorphic and metasomatic minerals and rarely diabase chilled margin. Mineralogical (diopside, actinolite, mica, sulfides, oxides) and chemical (Fe, Cu, S, Co) zoning of the eastern ore body is focused down dip, near its western edge, along a major vertical fault through diabase. This zoning is spatially related to magnetite veins in diabase, to an ore body within diabase, and to a shear zone that probably extends through the sheet.

Jan 1, 1968

By E. R. Phelps

A determination of feasibility of a new surface mining project requires a study in orderly fashion through the procedures outlined in Section 2 and the previous two chapters of this section. The information and data collected as described in Chapters 3.1 and 3.2 must be correlated, and the many variables that affect the venture must be reviewed. This review will furnish the mining engineer with the information required to make a preliminary evaluation of estimated profit in the venture. It is at this time that management must make yet another decision whether to drop or continue the project. 3.3-1. Maps. For the purpose of collecting, outlining, and correlating a large portion of the data required for a surface mining feasibility study, maps are essential. A map to a mining engineer is like a sheet of music to a musician, or a blueprint to a designer. It provides a pictorial method of presenting mining information not only for practical application in estimating and planning, but also for demonstration of physical relationships to those charged with decision-making responsibilities. GENERAL AREA MAP. The first step in the process of graphic information assembly is the preparation of a "small scale" general area map. Such a map may cover a mining district, a market area, a watershed area or district, or the whole or a section of a geologic feature such as an iron formation or coal seam. An example of such a general area map is shown in Fig. 3.3-la which outlines the various coal mining areas in the vicinity of a proposed "mine-mouth" power station, the Liddell Power Station Project. If Quadrangle Maps of the United States Geological Survey, or their equivalent, are available for an area, a common and very effective technique is to superimpose mining data on these maps, either directly or by means of transparent overlays. Valuable topographic information

Jan 1, 1968

By T. A. Sullivan

Refining in a molten salt electrolyte was investigated as a means of recovering nickel containing less than 1 percent and preferably less than 0.2 percent cobalt from nickel products containing up to 5 percent cobalt. Electrolytic separation of nick and cobalt was accomplished in a molten KCl-LiCl-NiCl2 electrolyte. Nickel containing less than 0.10 percent cobalt was routinely prepared. Factors that influenced the transfer of cobalt to the refined product were the nickel concentration of the electrolyte, the cobalt concentration of the electrolyte, the ratio of nickel to cobalt in the electrolyte, and cathode current densities. A method of recovering the cobalt from the electrolyte was developed. The possibility of preparing high-purity nickel by this process was shown, as well as the preparation of various cobalt-nickel-tungsten alloys.

Jan 1, 1968

By C. Gary Reiness

A safety glass eyepiece which had been repeatedly exposed to mine environment over a number of years was studied to determine some of its optical properties. In the regions from 385 to 400 mµ and from 625 to 760 mµ, the transmittance was less than the 89 percent required by the American Standard Safety Code for Head, Eye, and Respiratory Protection. From 200 to 320 mµ the relative transmittance of two parts of the eyepiece was found to vary widely, having a maximum of 38 percent difference at 315 mµ. Irradiation of the glass by ultraviolet light caused enhanced absorption in the range from 200 to 1,200 mµ. There was a time-dependent increase of 1016 color centers per cubic centimeter throughout this range after 36.5 hours of irradiation. The rate-of-growth curve for the optical density, at 243.5 mµ and 23° C, was resolved into linear and saturable components, indicating zero order and first order

Jan 1, 1968

By D. S. Cahn, D. W. Fuerstenau

Specimens of glass, plexiglass, and naturally occurring minerals were irradiated by a 15-joule ruby laser pulse to determine criteria for the fracture of nonmetallic solids by internal thermal stresses. Fracture did not occur in those specimens with either a very high or very low internal absorptance or with a high spectral reflectance. If significant amounts of melting and vaporization do not occur at the surface of irradiation, the specimen will fracture if a derived 11fracture stress" exceeds the ultimate tensile strength of the specimen. The purpose of this investigation was to determine criteria for the fracture of nonmetallic solids by internal thermal stresses which are caused by absorption of laser irradiation. A laser produces a very short pulse of light which has a high energy density distributed over a very narrow part of the visible spectrum. The laser system used in this investigation had an energy output of 15 0 joules at a wavelength of 6940 A. Fracture in a non-metallic solid, then, would be caused by the absorption of light energy by that solid, and subsequent conversion of this energy to heat or mechanical energy. Fracture is caused by internal stresses that result from rapidly imposed nonequilibrium thermal gradients. ANALYSIS OF CONDITIONS FOR FRACTURE BY LASER IRRADIATION For this analysis, the laser beam is assumed to be circular and centered on the junction of the major and minor axes of a rectangular specimen. The laser beam forms a cylinder of radius rb extending through the specimen width. The beam cylinder may be then thought of as a heated mass constrained by a surrounding unheated mass. The instantaneously heated cylinder will at-

Jan 1, 1968

By George M. Meisel

This paper is devoted to a discussion of the factors governing design of concentrators for large grinding circuits. Emphasis is placed on the manner in which use of ever larger grinding mills has affected the size of grinding bays, service cranes, gear reducers and electric motors, and the selection of ancillary equipment for cushioning of the starting load of large mills. Information is presented on the effect of using large grinding mills on the capital and operating costs of concentrators, e. g. : (Fig. 1) ? Benefits in lower cost of mills, drives and materials handling equipment, plant space, power, grinding media, operating labor and maintenance, and in ease of instrumentation and automation. ? Penalties in distribution of materials from the grinding mills to multiple lines of equipment which have not been developed to commensurately large sizes, and higher cost of ancillary equipment.

Jan 1, 1968

By D. G. Westlake

THE structure observed in thin foils by transmission electron microscopy is not necessarily representative of the initial bulk material. We have shown that hydrogen, originally present in a specimen of vanadium, niobium, or tantalum, can be concentrated by the thinning operation used to prepare foils from the bulk materials.' These foils exhibited domain walls indicative of a tetragonal distortion of the bcc unit cells, probably caused by ordering of the hydrogen in preferred interstitial sites. We believe this ordering does not occur at room temperature in the bulk material which contains less than 1 at. pct H. In a continued effort to prepare metal foils whose hydrogen concentrations remain constant during preparation, we have developed some new chemical and electrothinning techniques for vanadium. Each of the procedures presented in Table I produced foils that were thin enough for transmission electron microscopy. The experiments described below were performed to test the effect of each thinning procedure on hydro-

Jan 1, 1968