Search Documents

In conjunction with a study on wear of drag bits the effect of clearance angle on penetration rate was studied.Increases in clearance angle from 24 1/2 up to 30° gave an increase in penetration rate. Thereafter the rate was apparently affected by partial clogging with cuttings.Analysis of results was by a linear regression model and the t-test was applied to assess the significance of parameters in the penetration equation.

Jan 1, 1969

By G. P. Airey, R. F. Mehl, T. A. Hughes

The coarsening of cementite particles in a ferrite matrix has been studied in a series of steels with 0.15 pct C only and 0.15 pct C plus 1 pct Ni, Mn, and Cr, respectively. Two initial states were employed: quenched nartensite, and quenched and cold-rolled martensite. A series of tempering temperatures between 500' and 700" and tempering times of up to 190 hr were used. The structures were studied by replica and transmission electron microscopy. Particle size distribution curves were determined. From the average size value coarsening curves were obtained. These were plotted in accordance with the Wagner analysis assuming diffusion control. A discussion of the significance of the results is given. L HE reactions occuring upon the tempering of martensite have long engaged the attention of metallurgists. The latter stages, when cementite particles coarsen in a ferrite matrix, have been studied both qualitatively and quantitatively. Studies of such coarsening processes have recently been spurred by the publication of the Lifshitz-Wagner theory1, and the extension of this to the a Fe-Fe3C system by Oriani3 and by Li, Blakely, and einold. Following Wagner the coarsening process is often designated as "Ostwald Ripening". The only quantitative data on the rate of coarsening, except for the work of Hyam and uttin,' in the a Fe-Fe3C system are those of Bannyh, Modin, and odin' for a commercial eutectoid steel and those of Heckel and ereorio" using a pure eutectoid steel. The data of Bannyh, Modin, and Modin have been employed by 0riani3 to derive the a Fe-FeE interface energy. The reaction is one of the most important ones in steel and is worthy of detailed study. This is the purpose of the present study. Laboratory heats were prepared; these were steels with approximately 0.15 pct C, selected so that the num ber of carbide particles would be relatively small and thus so that the overlapping diffusion fluxes would be minimized, presumably a desirable circumstance.'-3 In addition to Fe-C alloys, comparable heats containing 1 pct of Ni, Mn, and Cr, respectively, were included with a view of appraising the effect of alloying elements. This report includes an account of the micro-structures observed, primarily with the electron microscope, and of kinetic data and their interpretation. MATERIALS AND TREATMENT The alloys were prepared from electrolytic iron ("Plastiron") and high-purity graphite; these were melted in a zirconia crucible using a vacuum furnace. The alloy steels were made by adding electrolytic nickel, electrolytic manganese, and "vacuum grade" chromium, respectively, under a partial pressure of argon. Each melt was poured into a mold within the vacuum furnace and cooled in the mold. The ingots were 2 in. in diam. and 8 to 10 in. long. The analysis of the alloys is given in Table I. These ingots were hot-rolled to strip 0.1 in. thick, then cold-rolled to 0.05 in. and each alloy split into two batches. One batch was austenitized at 1200 for 1 min, quenched in cold brine, then cold-rolled to 0.02 in.; samples given this treatment are hereinafter designated as "worked". The other batch was cold-rolled to 0.025 in., austenitized at 1200" for 1 min, and quenched in cold brine; such samples are hereinafter designated as "quenched". These two batches were then tempered, as below. The purpose of the treatment given the first batch was to provide an initial structure of cold-worked martensite, with the expectation that the additional defect structure created by cold work would encourage a higher rate of nucleation of cementite on tempering and hence a more uniform distribution of cementite particles. Individual specimens were sealed in evacuated quartz or Pyrex tubes, then tempered in a muffle furnace. The temperature control was better than 3'C at 700. Tempering treatments wer: performed at 400°, 500°, 550°, 600°, 65o°, and 700C for time periods between 15 min and 190 hr. PREPARATION OF SPECIMENS Specimens for optical and replicalelectron microscopy were mounted, polished conventionally, and etched with 2 pct nital. For electron microscopy, single-stage "formvar" replicas were made, dry-stripped and rotary-shadowed with chromium at an angle of 30 deg. Carbide extraction replicas were prepared from electropolished specimens usirig the method described by Smith and uttin.' Thin foils for electron transmission microscopy were prepared by chemical thinning in an H202-HF bath prior to electropolishing in a chromium trioxide-acetic acid solution. The most

Jan 1, 1969

By A. J. Stapleton

"This paper gives a brief description of the occurrence and development of the Needle Mountain mine at Gaspe Copper Mines, Limited and describes the trackless mining equipment used in this highly mechanized underground operation.Maintenance of the trackless equipment is considered in detail, with particular emphasis on scheduling and control, examination and inspection. All maintenance is carried out in an underground garage, and the facilities for maintenance and field repairs are also described. Maintenance costs are given for various units and the figures for different types of loading and haulage units are compared to support the trend toward larger units and the increasing use of rubber-tired loaders."

Jan 1, 1969

By W. J. D. Stone

"For several years, the existence of a deposit of barite (BaS04) near Brookfield, Nova Scotia, has been known. A very large deposit of strontium (SrS04) near Sydney, Cape Breton, is a more recent discovery. Cape Chemical Syndicate has been formed to work the deposits. A five-million-dollar integrated mineral processing and chemical plant is planned for Sydney to produce various compounds of barium and strontium. The mineral processing plant includes the Jones Wet Magnetic Separator and will produce high-purity barite and celestite. These products will be processed further in the fine grinding plant and the chemical plant. The general project is described, covering the deposits, processing and markets."

Jan 1, 1969

Jan 1, 1969

By David V. Ragone, James A. Craig, Richard E. Balzhiser

The Gibbs free energies of formation of UC2 and UC were measured by equilibrating two-phase mixtures of UC2 + C and UC, + UC with liquid bismuth. The measured equilibrium concentrations of uranium in the bismuth combined with available activity coefficient information yielded uranium activities in these two-phase regions. Measurements on UC2 were performed over the range 1015 to 1160 K and on UC over the range 1115° to 1165°K. The values obtained for UC2 are in excellent agveement with values determined using combustton calorimetry and low-temperature heat capacity measurements. The UC values are in fair agreement with the calorimetric values, differing by about 10 pct from the calorimetric determination. MUCH interest has been shown in the uranium carbides in recent years because of their potential as nuclear fuels. As nuclear reactor operating temperatures have been raised to increase thermal efficiency, new fuels have been required. The uranium carbides are of interest because of their high melting points, >2000°C, high thermal conductivity, and resistance to irradiation damage. The manufacture and use of uranium carbides are aided by a knowledge of their stability and reactivity under various conditions. In this regard the thermo-chemical properties of the carbides, i.e., heat capacity, heat of formation, free energy of formation, and so forth, are particularly important. A great amount of work has recently been done on the thermodynamics of the U-C system. Unfortunately, however, there has not been good agreement among the various investigations. This study of the free energies of formation of uranium monocarbide and uranium di-carbide in the temperature region 1100°-1200° K was undertaken to help clarify the situation. It should be noted that in the temperature range of this investigation, 1100°- 1200° K, the thermodynam-ically stable phase in equilibrium with graphite is U2C3, not UC2, Fig. 1. However, U2C3 is reported to be stable only under extremely low oxygen and nitrogen pressure. Although UC2 is metastable below 150O°C, it exists under most experimental conditions. It should also be noted that "UC," never exists as UC2 but with compositions near UC1.9. However, "UC2" will be used to designate the dicarbide phase except when the stoi-chiometry is necessary for clarity. METHOD The approach taken in this study of the free energies of formation of UC and UC2 was to determine the thermo- dynamic activities of uranium in the two-phase regions UC, + C and UC + UC, by equilibrating the two-phase mixtures with the liquid bismuth. When a mixture of solid UC2 + C is brought to equilibrium with liquid bismuth, the reaction that occurs is: Neither carbon nor UC, could be detected as dissolved material in the bismuth. The standard free energy for this reaction may be written: In the two-phase region UC, + C, Fig. 1, the thermo-dynamic activities of UC2 and carbon are unity. The activity of uranium in this region was determined by measuring the concentration of uranium in a liquid bismuth melt in equilibrium with the two-phase mixture. This concentration was then used in conjunction with the activity coefficient data of uranium in bismuth reported by Tien et al.' to determine the activity of uranium in the two-phase region, UC, + C. All of the quantities in Eq. [2] were then known, and the AG; (uc,) was evaluated. UC + UC2. For the studies involving UC + UC,, the reaction taking place when the two-phase mixture is brought to equilibrium with liquid bismuth is: The standard free-energy change for this reaction is given by:

Jan 1, 1969

By Robert Stefanko

The concept of disposing of liquid industrial wastes by deep-well injection is not a new one. Brines associated with crude oil long have been disposed of in this manner, with the additional benefit of aiding secondary oil recovery. More recently, with the expansion of nuclear energy, the lethal, highly radioactive wastes which are by-products of the fission process have created severe disposal problems. During the past ten years, a variety of industries have resorted to subsurface disposal, some of the details of which are given elsewhere (1,2). The list reveals wide variations in injection rate, pumping pressure, cost, and waste disposition. Included are successful installations in Western Pennsylvania.

Jan 1, 1969

By P. Crowther, G. J. Lamprecht

The solubilities of silver, zinc, and cerium in liquid sodium, in the temperature ranges 100 to 270°C, 190° to 550°C, and 120" to 460°C, respectively, have been determined. From the solubility data the heat the entropy the partial molal enthalpy of mixing the excess entropy and the partial molal free energy of solution for the systems Nu-Ag and Na-Zn have been calculated. For the system Na-Ce the observed negative is discussed in terms of the solubility of the oxide Ce2O3. In an earlier publication the results obtained in the study of the solubility of tin' in liquid sodium are presented, as well as the detailed analytical procedures used. 1) REAGENTS Spectroscopically pure metals as supplied by Johnson Matthey and Co, were used to produce the following tracers: 253-day Ag110, 245-day zn65, and 325-day ce141. The tracers were prepared by irradiation in a thermal neutron flux of 4 x 10 13 neutrons cm-2 sek-1. To obtain a uniform amount of the required specific activity, needed for each solubility experiment, the radioactive metal was diluted with the corresponding inactive metal, by melting them together in an inert atmosphere. The liquid sodium used contained 11 ±2 ppm of O,1 determined by the vacuum distillation method.' The oxygen was assumed to be present as the oxide NaD. 2) THE SYSTEMS: SODIUM-SILVER AND SODIUM-ZINC Plots were made of the log of the mole fraction of silver, Fig. 1, and of zinc, Fig. 2, dissolved in the liquid sodium vs reciprocal absolute temperature. The equations for the solubilities, based on the least-squares fit to each plot, are: where Xi is the mole fraction metal dissolved in sodium, T is the absolute temperature, and s is the standard deviation in the value of log Xi. The heats and the entropies lution were calculated from the solubility data by In neither of the two cases was any intermetallic compound formed between sodium and the solute metal as was the case for tin.' Thus, for the silver and zinc systems the pure metal was taken as the reference phase. Since the solids in equilibrium with the liquid sodium were the pure metals, one can calculate the partial molal enthalpy of mixing and

Jan 1, 1969

By Louis A. Rosales, Kanji Ono

The anomalous behavior of hydrogen in iron is examined and a new model is proposed It is postulated that hydrogen single and di-interstitials are in equilibrium with each other. When the binding enthalpy of the di-interstitial, B, is assumed to be about 10 kcal per mole, the predicted temperature dependence of the solubility agrees reasonably well with the reported data. Effective diffusiuity is calculated assuming the di-interstitials to be immobile. Since the number of mobile single interstitials is greatly reduced at lower temperatures, the effective diffusivity is decreased. A good agreement in the temperature dependence of diffusivity between theory and experiment is provided with B - 10 kcal per mole. The predicted diffusivity is also a function of total concentration of hydrogen and this appears to be Partly responsible for the large scatter in the reported data. HYDROGEN is known to form an interstitial solid solution with iron.''' At elevated temperatures, it has been well-established that hydrogen enters iron in the dissociated form and occupies the interstices, and that diffusion of hydrogen in iron is via the interstitial mechanism. The concentration, c, permeability, P, and diffusivity, D, of hydrogen in iron have been separately determined and are consistent with each other under the steady-state condition for temperatures above approximately 400°C; that is, the relationship P = c-D holds. At lower temperatures, however, anomalous behavior of hydrogen in iron has been observed by many investigators. The results of experimental studies4-'' of the diffusion of hydrogen in iron are summarized in Fig. 1, in which the values of D are plotted against the reciprocal temperature. Although there is an increasing divergence in observed values of D with decreasing temperature, the values of D at temperatures below approximately 200°C are definitely small as compared with the extrapolation from high-temperature data. The lines shown bracket the region containing the most probable data. The observed values of c6," are plotted against the reciprocal temperature in Fig. 2, where the dashed lines represent Geller and sun's'' most probable isobars at 1 and 100 atm. At high external hydrogen pressure and low temperatures, the values of c observed are higher than those expected from high temperature data. It is generally accepted that certain trapping mechanism is responsible for the anomalies, but the nature of the trapping mechanism has not been clarified. Various types of hydrogen traps were suggested in the literature, such as "rifts" in the lattice dislocations, voids, microcracks, and so forth. However, no quantitative account of the observed behavior has been given in terms of these trapping mechanisms. Formation of methane in hydrogen-charged steel was found by ~odgurski." This appears to explain the existence of the so-called "residual" hydrogen,4 but not the observed anomalies of hydrogen in iron. McNabb and Foster' proposed a mathematical analysis in terms of a trapping mechanism. However, the physical significance of the traps was not clarified. The necessity of evaluating five parameters in their theory made comparison with experiment difficult. In the present paper, a model is proposed in which the anomalous behavior of hydrogen is attributed to the formation of hydrogen di-interstitials at lower temperatures. In this model, it is postulated that single and di-interstitials are in equilibrium with each other. (The hydrogen di-interstitial is to be distinguished from a hydrogen molecule which may exist in voids.) It can then be shown that most of the anomalies can be explained by assuming that the di-interstitials are virtually immobile and that the binding enthalpy of the di-interstitial, B, is approximately 10 kcal per mole. Predictions of the theory agree with the available experimental data reasonably well. THEORY The basic postulate of the present analysis is that single and di-interstitials are in equilibrium with each

Jan 1, 1969

By John Kostuik

"This paper discusses the outlook for uranium resources, and comments briefly on the measures needed to meet market objectives. Areas of recent exploration interest are also discussed.THE PREVIOUS SPEAKER has capably described the truly phenomenal growth in demand for energy from all sources. The basic factors -population growth and industrial development -which will create energy demand are so fundamental to national economies that the ascending energy demand curve will be little affected by short-term factors.Because of the economic and practical advantages of nuclear power and the degree of present acceptance by electric utilities, there is no doubt that uranium will be a principal source of primary energy in industrial countries -and this will happen within a decade. Indeed, during this period it will be the fastest growing source of energy, capturing, for example, more than half of the electric utilities' expansion in the United States by 1980. The ready availability of energy sources from domestic and foreign resources is so essential to industrial nations that the long-range outlook for their adequacy is of prime importance. There has been international concern about the availability of uranium resources at reasonable cost to adequately support and foster the development of the nuclear power industry. Canada, fortunate in having established reserves and a potential in excess of any forseeable domestic demand, can confidently look forward to being a principal supplier to the industry."

Jan 1, 1969

By William Paxton Hewitt

In the Santa Eulalia mining district, Chihuahua, Mexico, the main mineral zone occurs in a gently warped dome with simple associated structures and contains orebodies distributed through a vertical range of over 900 m. The stratigraphy of 1945 m of geologic column is described and an abrupt shrinkage is documented in the volume of limestones immediately associated with large orebodies. Termed collapse, this shrinkage occurred during the course of mineralization. Contacts of limestone with igneous sills, and 366 m of fossiliferous limestone beds, particularly the main fossil bed, have been important localizers of ore-bodies. Up-dip gravitational controls may have been important. Fractures have exerted only local controls and over short distances. Thrust zones have displaced diabase sills and in turn have been intruded by upper members of a group of rhyolite porphyry sills. Mineralizers were related to the rhyolite porphyry, and ore has been introduced to the limestone where certain sills lie between the displaced segments of diabase and have been cut by north-south fissures. Speculations are raised that fields of unreleased strain may have influenced orebody locations; the district's zoning pattern may be a reflection of the filtering effects of large volumes of limestone; and that metal-rich brines mobilized by or incorporated within the invading porphyry might be the source of the mineralizers. PRODUCTION AND LOCATION The Santa Eulalia district has a production record approaching or exceeding 35 million tons of silver-lead-zinc ore from replacement bodies in limestone. In operation since the first years of the 17001s, production has been confined to two intensely mineralized areas separated by 2 km of barren limestone, the West Camp and the East Camp. Probably 50% has been mined since 1908, with over 90% from the West Camp. The West Camp, exploited through a vertical depth of 1945 m and now approaching exhaustion, is the subject of this paper. The district lies in the northern part of the Santa Eulalia Mountains in central Chihuahua in northern Mexico, 400 km south of El Paso, Texas, and 22 km southeast of Chihuahua City. Dominating the northern part of the range is the Cerro de Santa Eulalia, a broad rolling upland which contains the district's West and East Camps. The West Camp, on the west side of the range, centers around the village of Santo Domingo, which is 2 km northeast of the Real de Santa Eulalia (Fig. 1). REGIONAL GEOLOGY Thick-bedded middle Cretaceous limestones, probably Aurora, form the great bulk of the Cerro de Santa Eulalia. These beds, warped into a gentle dome, are severed on the west by a faultline scarp and truncated on the north by the Dolores Pass, a wind gap that

Jan 1, 1969

By Van C. Nyman

A time-sharing computer was tied in to Hecla in August of 1967. This has proven to be helpful in performing metallurgical and engineering calculations that were formerly tedious tasks. Metallurgy programs were written for applying two and three product formulas. Programs were expanded to make the monthly metallurgical balance calculations for each of the Hecla mills. The Hecla engineering department uses the computer for solving hoist duty cycles and for traverse analysis. Both Asarco and Bunker Hill Company in the Coeur d’Alene Mining District are tied to a time-sharing computer. Their uses for the time-sharing computer will be discussed. Asarco had the advantage in learning computer techniques during an extended strike. A comparison of Asarco computer use with that of Hecla's will show the advantage in having a person or persons spend full time on the use of computers. Bunker Hill has the versatility of five teletype units in their mine-smelter complex plus ability to tie in to their own computer.

Jan 1, 1969

By J. E. Strassner

Oilfield emulsions are stabilized primarily by film-forming asphaltenes and resins containing organic acids and bases. Adding inorganic acids and bases radically changes the physical properties of these films and their emulsion-stabilizing properties. Interfacial films show one of three different physical characteristics when retracted in pendent drop tests. These compressed films have rigid, soap-type or minimum film properties depending on the quantity of asphaltenes and resins in the crude oil and on the pH and composition of the brine. There exists for each crude oil-brine system an optimum pH range over which the adsorbed film exhibits minimum contracted filtn properties. In this range, intmfacial tension is high — frequently near its maximum value — indicating the absence of highly surface-active specier; crude oil-brine emulsions generally show minimum stability; and surfactant requirements for breaking these emulsions are significantly reduced — sometimes no surfactant is needed. About two-thirds of the world's crude oil is produced as emulsions that must be treated (demulsified) to be marketed.' Approximately three-fourths of all domestic crude oil produced must be treated. The percentage of crude requiring treatment increases as fields become older and more water is produced. Demulsification most frequently is attained through use of surfactants, heat and electric treaters. It is estimated that over 75 percent of all oilfield emulsions are broken by chemicals generally containing alkylene oxide condensates. Although acids and bases are known to affect emulsion stability:-' they rarely are used in the oil field except in batch treatment of the most severe emulsions. Nevertheless, pH adjustment by using acids or bases in demulsification has some advantages over other methods. Mainly, it is cheaper. Acids and bases frequently are cheaper to use than surfactants, or can appreciably reduce the amount of surfactant required for demulsification. Secondary advantages are that less oil is lost by emulsi-fication into the aqueous phase, and that less corrosion is encountered when the optimum pH is basic. Limitations to the use of pH include (1) use in brines containing high concentrations of reactive ions, (2) closer supervision for pH control than is required for surfactants and (3) need for corrosion protection when the optimum pH is sufficiently acidic. These factors indicate that the economics of pH con trol in demulsification will be maximized when relatively large treating facilities are needed, when relatively large surfactant concentrations are required to break an emulsion, when a relatively low concentration of the aqueous phase is emulsified in the oil and when the emulsified aqueous phase contains relatively low concentrations of reactive ions. Because there are no broad guide lines for using pH control in breaking oillield emulsions (and because the limited guides available are highly specific and frequently contradictory), this paper will attempt to clarify the principles involved in using acids and bases to break emulsions. These principles also should be useful in refinery separations and in other oilfield applications where stable or unstable petroleum emulsions are involved. Principles of Emulsion Stability Oilfield emulsions generally occur as water droplets dispersed in oil (w/o) and occasionally as oil droplets in water (o/w). These emulsion droplets are usually in the 0.1- to 10-micron range. However, more coarsely dispersed water droplets frequently are present in the emulsion. Pure hydrocarbons and water will not form stable emulsii except in extreme dilutions where the large distance brtween droplets inhibits coalescence. An emulsion breaks because interfacial tension acts to minimize the surface area of the dispersed drops by coalescence. However, emulsions can be stablized for long periods of time by the presence of a third phase that adsorbs at the oil-water interface and inhibits coalescence of the dispersed phase."' Emulsions generally are stabilized by (1) repulsive charges on the surfaces of the dispersed phase and (2) adsorbed films that, being preferentially wetted by the continuous phase, act as a physical barrier to inhibit contact between the dispersed droplets. Both these factors generally are important in stabilizing and in breaking o/w emulsions. However, repulsive charges are less effective in stabilizing w/o emulsions which generally are stabilized by adsorbed films.V or this reason the nature and importance of these films at oil-water interfaces were examined closely; as will be shown, pH changes were found to affect the films significantly, and this work led to laboratory tests of pH- adjustment in emulsion breaking. This paper will present evidence to show that emulsions are stabilized primarily by films that form around droplets

Jan 1, 1969

By K. R. Van Doren

The polynomial method for estimating virial coefficients from experimental data suffers from three serious defects: (1) There is no known relationship between the polynomial coefficients and the virial coefficients, (2) the values of the estimates depend upon the degree of the polynomial and the particular set of values used for the independent variable, as well as the random errors in the dependent variable, and (3) the variances calculated for the estimates do not represent the mean square errors of estimation. Attempts to overcome these defects have thus far been unsuccessful; these attempts have also failed to account for the fact that none of the virial coefficients are uniquely determined by the values of the dependent variable for a finite set of values of the independent variable. The conclusion is that virial coefficients cannot be reliably estimated from experimental data unless additional information about the virial expansion itself, such as its rate of convergence, is available.

Jan 1, 1969

By A. C. Ross

"The paper will deal with non-destructive testing in general, and its advantages to those responsible for the maintenance of wire rope. An outline of the main features of the M.D. 6 Defectograph will be given, and the method of operation and results obtained will be described.The instrument will accommodate ropes at 7 /16-to 2 %-inch diameter at reasonable speeds, and is capable of detecting the most minute defects in even the largest-diameter wire ropes."

Jan 1, 1969

By E. Klar, A. B. Michael

Differences in the electrical conductivities of copper powder sintered under reducing, selectively oxidizing, and neutral atmospheres are related to impurities in solution or as precipitated oxides. The precipitation of impurities as oxides during sintering in nitrogen is proposed for maximizing the conductivity of sintered copper. Conductivity equations for two-phase systems are summarized. Selected equations are applied to porous sintered copper and composite structures. A recent review of the influence of impurities on the electrical conductivity of copper by Gregory et al.1 emphasized that an impurity in solid solution has a much more pronounced effect on reducing the electrical conductivity than when present partly or wholly as a second phase. When impurities in solid solution can be precipitated as oxides, the copper is purified with respect to these elements and the conductivity is increased. Cast and wrought copper, therefore, frequently contain an intentional residual oxygen concentration to oxidize and precipitate impurities less noble than copper. Copper powders generally also contain impurities which can contribute to a reduction in the electrical conductivity of the sintered material. The most deleterious impurities commonly found in commercial copper powders which markedly decrease the electrical conductivity when in solid solution but which can be precipitated as oxides include iron, tin, antimony, arsenic, cobalt, and nickel. In addition to impurities, porosity in sintered copper also contributes to a reduction in the electrical conductivity. The work reported herein discusses the influence of impurities, sintering atmospheres, and porosity on the electrical conductivity of sintered copper. These are important factors for controlling the electrical conductivity of materials such as sintered copper electrical contacts. Several publications on the electrical conductivity of sintered copper and composite materials with random pores or obstacles have incorrectly considered the conductivity to be proportional to the volume fraction of conducting material. However, analyses and equations have been proposed, the earliest of which is perhaps Lord Raleigh's of 1892,' which more accurately describe the conductivity of two-phase systems. These equations which in many cases allow one to closely estimate the electrical conductivity of porous sintered materials and two-phase composites will be reviewed and related to the measured electrical conductivity of sintered copper, copper-graphite. and Ag-W composites. INFLUENCE OF IMPURITIES AND OXIDIZING, REDUCING, AND NEUTRAL ATMOSPHERES Zone-Melted and Leveled Copper. The electrical conductivities of an electrolytic copper and a lower-purity compacting grade of copper powder after consecutive treatments in reducing or selectively oxidizing atmospheres are compared in Fig. 1. The powder and drillings from the electrolytic copper ingot were melted and solidified in a graphite crucible under hydrogen. The vertical zone leveling technique of multiple passes in opposite directions was used to obtain a uniform distribution of impurities. The electrical conductivity was measured on machined specimens 3 by 0.10 in. diam of the zone-leveled material and after the same specimens were consecutively treated as follows: 1) heating in hydrogen at 1600°F for 3 hr; 2) heating in air in a sealed tube so that 0.04 pct 0 was introduced; heating was started at 1000°F for 1 hr and continued at 1800°F for 8 hr; the stepwise diffusion treatment was used to avoid loss of copper due to evaporation of copper oxide at higher temperatures; and 3) final heating in hydrogen at 1600°F for 3 hr. A L&N Kelvin Bridge, type 4306, and a test fixture with knife edges 2 in. apart were used to measure the room-temperature conductivity with an estimated accuracy of ±0.5 pct. In all cases the conductivity of the electrolytic copper was approximately 100 pct of IACS. The conductivity of the impure copper was 80 pct of IACS both in the cast state and after heating in hydrogen. However, after the heating in air, the conductivity of the impure material was 100 pct IACS. After again heating in hydrogen, the electrical conductivity decreased to 60 pct of IACS. This decrease is attributed both to the dissolution of impurities and observed intergranular cracks due to the phenomenon of hydrogen embrittle-ment in copper. These data show that the electrical conductivity of commercial copper as represented by a compacting type powder can be increased significantly by the precipitation of impurities as oxides through heat treatment in an oxidizing atmosphere. Sintered Copper Powder. A commercial compacting type of copper powder pressed to various densities was sintered either in nitrogen, dissociated ammonia, or dissociated ammonia followed by a selectively oxidizing atmosphere of air in sealed Vycor tubes so that 0.06 pct O was added to the material. The electrical conductivity was measured perpendicular to the pressing direction on as-sintered specimens of approximately 3 by 0.25 by 0.15 in. The fully dense material was obtained by zone melting and leveling

Jan 1, 1969

By E. J. Freeh, W. E. Horst, R. C. Kellner

A technique useful in the important area of process-model building is described. The procedure is illustrated in the development of a mathematical model to describe the unsteady-state process of batch ball-mill grinding. The influence of certain assumptions relative to model structure are quantitatively evaluated and reviewed.

Jan 1, 1969

By W. B. Morrison

Anderson, King, and Spreadborough present detailed evidence to show what ~aldwin~' has already pointed out, that, over a relatively small grain-size range (Ad"1/2 ^ 10 mm-'I2, d is average grain diameter), yield point data can fit a number of relationships. Part of the difficulty in obtaining data which reflect only the effect of change in grain size on yielding arises from the fact that in varying the grain size, even though great care is taken, other structural changes are almost certain to occur. In iron alloys, these changes may consist of variations in subgrain size, grain boundary ledge density, and degree of carbon and nitrogen segregation at grain boundaries, all of which are difficult to detect and which may affect yielding, primarily through their effect on dislocation generation. Because of the inherent inaccuracy associated with yield point measurements there is little point in using relatively complex equations to fit data, as was done by Anderson et mnl., rather than the simpler, widely used Hall-Petch equation. In compiling their table of data, it is surprising that they did not include results from certain low-carbon steels,31 in which, as illustrated in Fig. 2, the grain-size range is very much larger than in their Armco Iron. The very fine grains in these steels were obtained by a thermomechanical process. Examination by electron microscopy showed that the grains were separated by high-angle boundarie and contained only an occasional subboundary. The data from these steels obeyed the Hall-Petch equation, and it was shown quite conclusively that they did not fit a d-l or (1-lJ3 relationship. Obviously, a much wider range in grain size than used by Anderson et al. is desirable if we are to determine the true relation between lower yield stress and grain size.

Jan 1, 1969

By R. Stefanko

Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, development of suitable instrumentation that is simple to install and readout, sensitive, durable, reliable, safe and economical in evaluating the effectiveness of a bolt over long periods of time lags behind. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At Penn State in the Department of Mining, research has been conducted for a number of years to measure bleedoff in carefully controlled laboratory experiments as well as in underground investigations.1,2,3,4 Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be conducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised.

Jan 1, 1969

By A. U. Seybolt, V. A. Phillips

Binary iron alloys containing 1 pct of Al, Cr, Mn, Mo, Si, Ti, or V, and 0.4 pct C, 1 pct Cr steels with and without 1.2 pct A1 or 2.0 pct Ti additions, were ion-nilrided at 550° to 600° in N-H mixtures. Nitriding increased the inicrohardne ss of all the binary alloys except those containing manganese or molybdenutn, and also hardened the heat-treated steels if aluminum or titanium urns present. Transmission electron microscopy revealed particle formation in all casts where hardening occurred. Electron diffraction gare positive identifications for ALN, CrN, and a, Si3N4 in the binary alloys, and AlN and CrN in the aluminum- cold chromium-bearing steels, respectil&apos;uly. Cubic VN with a, = 4.13A was tentatively identified. Particles, apparently of CrN, also formed in the base steel but did not increase the hardness very much. Chromium and vanadium formed nitride platelets on {001}° matrix planes, while titanium gave clusters <15A diam. Aluminum nitride precipitated at grain and subgrain boundaries, and within the grains. Silicon gave profuse precipitates of several Morphologies at grain boundaries and cubical particles within the grains. No effect of the alloy carbides on nitride precipitation was observed in the heat-treated steels. THE nitriding of steel has been a well-established commercial process for about 40 years, but in spite of this comparatively long period of use there have been few studies aimed at understanding the process. Most studies, like the early but very competent work of Jones and organ&apos; and nones.&apos; were concerned with establishing the pertinent engineering variables of steel composition, gas composition, temperature, and time. As far as the present authors are aware, there have been no studies of the composition, size, shape, or distribution of the nitrides formed in the nitriding of steel. Noren and Kindbom3 did, however, examine a few nitrided steels by surface replica electron microscopy, and were able to show the presence of car-bonitrides and AlN and TiN nitrides. pitsch4,5 and Hrivnak6 examined nitrided pure iron by transmission electron microscopy. Baird7 found manganese nitrides in Fe-1.6 pct Mn when nitrided at 650°C, using the same technique. In the present work, emphasis was placed on transmission electron microscopy because of its inherently better resolution, using principally binary alloys of iron containing 1 pct of alloying element. In addition, a few simple 0.4 pct C steel compositions were examined to investigate possible carbonitride formation. It was not anticipated that all of the added elements would form nitrides under the conditions used, but it was considered desirable to obtain direct experimental evidence on this point. It would be considerably easier to ascertain the presence of alloy nitrides by examining appropriate binary alloys in preference to relatively complex steels. The work reported here could have been done using orthodox ammonia-nitriding procedures, but an operating ion-nitriding equipment was available, and was therefore used for specimen preparation. EXPERIMENTAL DETAILS 1) Materials. Binary alloys were made up from vacuum-melted electrolytic iron with 1 wt pct additions of Cr, Ti, V, Al, Mn, Mo, and Si of about 99.9 pct purity. In addition, three steels were similarly made up—a basis steel with 1 wt pct Cr and 0.4 wt pct C and two steels with further additions of 1.2 wt pct A1 or 2.0 wt pct Ti, respectively. The materials were vacuum-melted and cast as 11-lb heats into tapered square molds of about 2 by 2 in. average cross section. The castings were forged and hot-rolled to 11/4 in. rounds. Discs of 4 in. thickness by about 1 in. diam were machined from the rods. Some of these discs were hot-forged and hot-rolled to about 0.020 in. thick, sand-blasted, and then cold-rolled to about 0.003 in. thick. At this point, the surface was cleaned by light etching with HC1, then washed, dried, and vapor-degreased prior to nitriding. 2) Ion-Nitriding Procedure. The type of ion-nitriding equipment used here is similar to that described by Jones and Martin.8 Briefly, a mixture of nitrogen and hydrogen at 5 mm total pressure is placed in a vacuum chamber with a dc potential of 450 to 500 v applied between the work (cathode) and the grounded metal vacuum enclosure (anode). Nitrogen ions are accelerated to the work where a thin layer of Fe4N forms on the surface and thus sets up a nitrogen concentration gradient. This causes nitrogen atoms to diffuse into the surface layers of the alloy forming a finely divided dispersion of alloy nitrides, causing hardening of the surface. In the work to be reported here. the nitriding was carried out at 550° to 600°C to be consistent with commercial nitriding practice. The temperatures cited are those measured by a thermocouple located under a platform on which the work was sitting. Except where otherwise stated, the mixture used in nitriding the binary alloys contained -2.0 pct N, balance hydrogen. The nitrogen concentration in the nitriding gas mixture used for the binary alloys was purposely kept lower than normally used in nitriding steels. 10 to 20 pct, in order to minimize Fe4N formation. In this way only the alloy nitrides would be present as a second phase. However, in the case of steels which would contain a- carbide phase along with as

Jan 1, 1969