Search Documents

By Harrison R. Cooper

With problems of diminishing ore grades and increasing cost of facilities, the mineral industry is acutely aware of the needs for improving beneficiation processes. Industry and universities are directing intensive technical effort to develop- ment of techniques with potential for using digital computers in automation and process analysis. The main problem of early attempts at on-line computer process control methods was that of economics. Now, with new advances in analysis and modeling making practical application economically important, it appears that minerals beneficiation is on the threshold of a significant jump in operating technology. In reviewing this work, particular note was taken of research and development applied to fundamental processes and the significant areas of effort where operations research techniques are used for process applications leading to the current state-of-the-art. Development of data automation and on-line control methods for process industries is deferred to the next section of this volume. This section deals with computer-facilitated mathematical-modeling development and reviews this work in conjunction with associated prior fundamental research leading to development of the methods. Flotation The 1960 state-of -the -art in flotation modeling was com- piled by Arbiter and Harris in the volume, 50th Anniversary of Froth Flotation, edited by Fuerstenau1. Many workers in the field of flotation initiated their research through flotation models, and this effort has led to use of simulation and operations re search methods employing computer techniques to facilitate advance of this work. The flotation model of Imaizumi and Inoue, published with supporting data in 1962, was expanded in 1968 with the objective of developing a basis for process automation.2,3 The fundamental work of Woodburn and Loveday in 1965 has led to techniques applicable to flotation circuit design optimization.4 This analysis is described in this volume by Woodburn in conjunction with King, Buchalter, and Piper. Niemi5,6 derived models for dynamics of a flotation circuit which were employed in developing a model describing

Jan 1, 1969

By A. F. Crawley

The density and viscosity of 1iquid thallium have been measured by absolute methods to temperatures of about 200° and 150°C, respectively, above the melting point. These new data reported, especially density data, do not closely confirm previous work. Density p, in g per cu Cm, is shown to vary linearly with temperaluve t, in °C, according to the equation p = 11.658 - 1.439 X l0-3t. The viscosity data obey the well-known Andrade equation nv1/3 = A exp C/vT , the constants A and C for thallium having values of 2.19 x A and 79.648, respectively. This paper reports some new data for the density and viscosity .of liquid thallium. Measurements of these fundamental physical properties were undertaken as part of a continuing research program at the Mines Branch, Department of Energy, Mines and Resources, Ottawa. Canada. A literature search has revealed that data are so scarce that there could not be a consensus on the true values of the density and viscosity of liquid thallium. To be more specific, there exists only one set of viscosity data' and only two acceptable sets of density data,273 one of which is limited in scope.3 In Liquid Metals Handbook,3 another density study is reported but indications of impurities in the thallium render the results suspect. In this situation, further careful experimentation was required to realize the true density and viscosity of thallium. EXPERIMENTAL METHODS Density. Densities were determined using a graphite pycnometer. The technique and its accuracy have been discussed in earlier papers.4'5 It is considered that experimental data can be obtained which are accurate within +0.05 pct, all sources of random and systematic errors having been evaluated. Density results for thallium were identical whether measured under an atmosphere of argon or a vacuum of 5 x 10-6 torr and, for the most part, the argon atmosphere was used. Viscosity. Viscosity measurements were made in an oscillational viscosimeter by an absolute method—the liquid metal being held in a closed graphite cylinder. Design and operation of the apparatus, constructed in this laboratory, have previously been discussed.6 For thallium, runs were made under a vacuum of about 2 x 10-6 torr. To evaluate viscosity coefficients from the various experimental parameters, the mathematical analysis of Roscoe7 was used. Measurements of the necessary parameters and the accuracy of these measurements have also been discussed.6 The cylinder dimensions were corrected for the anisotropic expansion of graphite, as discussed for density measurements.4,5 It is well-known that thallium oxidizes rapidly and hence a newly machined surface quickly tarnishes in air. The oxide film, however. is nonadherent and is easily removed by rubbing or by solution in water. Hence, immediately before use, both density and viscosity charges were immersed in water, wiped dry, and quickly transferred to the apparatus which was then rapidly evacuated. Specimens removed after determinations were only slightly tarnished and there was no other evidence that tarnishing affected the results. For example, the sharpness of the specimen edges from the containing vessels indicated complete filling by the liquid metal. Thallium of 99.999 pct purity was used in this investigation. Because of its high toxicity care was exercised in handling this material. For example, the melting procedure to prepare machinable ingots was carried out in an open, well-ventilated area, while protective gloves were always worn when handling the solid metal. RESULTS AND DISCUSSION Density. Measurements were made over a tempera-ture range of about 200°C above the melting point. The results are listed in Table I and plotted in Fig. 1. From the graph it is evident that the relation between density and temperature is linear. Such a relation has been observed before in this program for other metals and alloys475 and elsewhere by other workers. A least-squares analysis of experimental data gives the equation: pT1 = 11.658 - 1.439 x 10-3t where p = density in g per cu cm and t = temperature in "C. In Fig. 1, together with the present results, the data of Schneider and Heymer2 in the corresponding temperature range have also been plotted. Evidently, the two sets of data do not agree well, the results of Schneider and Heymer being about 0.6 pct higher. Viscosity. Viscosity data were obtained from the melting point, 303.5°C, up to 457.5"C. The data are listed in Table I and in Fig. 2 the plot of these results demonstrates a smooth curvilinear relation between

Jan 1, 1969

By Boris J. Kochanowsky, Burke O. Trafton

Because of the strict requirements on the quality of limestone that are dictated by the users, the operator was compelled to find new approaches to produce a product of uniform and acceptable quality. The raw material is controlled and monitored every two minutes by a special computer in order to ensure its quality. The required minimum and maximum quality constraint had an adverse effect on performance and consequently cost. In order to improve this performance, a Monte Carlo simulation model was developed and tested for the optimal truck allocation. The input data is based upon the distribution of equipment performances and costs.

Jan 1, 1969

By M. J. Kovalik

Lower Sunnyside seam coal from Utah was blended with various proportions of char and high-temperature coke to improve the quality of the coke obtained from carbonizing this coal. The Hanson 5-pound carbonizer was used as a "screening test" for the larger scale Bureau of Mines-American Gas Association (BM-AGA) tests, which were correlated with industrial production. Eighteen carbonization tests were made in the BM-AGA 13-inch retort, with a coal charge of about 90 pounds; the cokes were evaluated by the standard ASTM tumbler test. Carbonization of blends containing char and coke breeze yielded less fissured and blockier cokes of significantly higher ASTM I-inch tumbler indices as compared with the value for the straight Sunnyside coal. It was found that the simultaneous addition of char and coke breeze yielded stronger cokes than that obtained by the addition of either one of these additives. Addition of a small proportion of Pocahontas No. 3 or Sewell coal to an optimum blend improved the resulting coke strength further.

Jan 1, 1969

By R. E. Reed-Hill, W. H. Hartt

The second order, {1011}-{1012} twin bands observed in critically deformed magnesium are often accompanied by an unusual form of kinking. These kinks, which lie adjacent to and run more or less parallel to the twin band habit, allow plastic deformation that occurs inside the twins to be accommodated into the matrix. The bend planes of these kinks cannot be explained using slip dislocations with Burgers vectors lying in the basal plane. A mechanism involving a single set of {1012)(1011) dislocations is proposed to account for the kink band habit, in good agreement with the experimental observations. It has been shown that second order, {101l)-{1012} twinning is an important phenomenon for magnesium deformed in the ambient temperature range. A detailed study of these twins has recently led to a better understanding of their irrational habit plane1 and their relation to fracture in magnesium.' This paper is concerned with a third aspect of these twins; this being the kink bands, originally referred to as shear accommodation kinks,3'4 that are often induced in the adjacent matrix. A twin band and its shear accommodation kink usually appear as a single macroscopic deformation, as seen in Fig. 1. The complex nature of these deformed regions is easily revealed, however, with the aid of a suitable microscope. It has been proposed374 that the primary function of these kinks is to accommodate the nonhomogeneous deformation that normally occurs in the second order twins. The twins tend to form as small discrete lamellae lined up approximately one in front of the other.''' Very large plastic deformations varying in magnitude from one twin to the next, may occur inside these lamellae. The kinks serve both to pass this strain into the matrix and to accommodate strain variations between twins. Deformation within the kinks, subsequent to their formation, has also been observed;3,4 and it is thought that this contributes to the strain accommodation process. The bend planes of the kinks have a habit near that of the twin band itself, which lies about 56 deg from the matrix basal plane. This orientation does not bisect the angle formed between the basal plane to either side of the bend plane and therefore differs markedly from the kink structure usually observed in hcp metals.'-' The present paper reports the results of a study of shear accommodation kinks and proposes a possible solution to the problem of the orientation of the bend plane. EXPERIMENTAL PROCEDURE Rectangular cross-section tensile specimens with axes parallel to (1010) and faces to (1210) and (0001) were cut and acid machined from a high-purity magnesium single crystal. After straining on an Instron machine the specimens were examined by both optical and replica electron microscopy. The basic procedures have been previously reported."' EXPERIMENTAL RESULTS AND DISCUSSION Structure of Shear Accommodation Kinks. A typical, large (101l)-{1012) twin band with its associated shear accommodation kink is shown running diagonally from upper left to lower right in Fig. 1. In this optical micrograph the twin band, consisting of a row of small, highly deformed twin lamellae, is visible as a narrow dark band along the left hand edge of the structure in question. The kink lies to the right of the twins, is approximately three times as wide, and is lighter in contrast. The horizontal slip lines visible on the general specimen surface correspond to matrix basal slip and are parallel to the tensile axis. Note that on the right-hand side of the band these slip lines can be followed from the matrix into the kink. At the kink band boundary the slip lines suffer a clockwise rotation of about 25 deg. Rotations of this magnitude are not uncommon. When a surface such as that in Fig. 1 is given an etch1 making it sensitive to polarized light, it has been observed that the slip traces in the kink are parallel to the basal plane trace in this region. This is in excellent agreement with the assumption that these regions are indeed kinks. Fig. 2 is an electron micrograph of this same twin band and kink. Note that a row of small supplimation pits has formed

Jan 1, 1969

By Alton B. Cook

Data are presented to show oil vaporization resulting from the passage of natural gas through a sand-packed tube saturated with synthetic reservoir oils. The Bureau of Mines performed 13 experiments, using reservoir oils synthesized with base crude oils of approximately 22°, 35°, and 45° API, at 100°, 175°, or 250° F and 1,100, 2,600, or 4,100 psia. It has been determined that the amount of vaporization is significant if proper conditions exist. These experiments show that oil vaporization depends on pressure, temperature, volatility of the oil, and amount of gas cycled. Increases in each of these conditions increase the volume of oil vaporized.

Jan 1, 1969

By Peter F. Mataich

The phosphate mining industry is a highly competitive one, one in which survival depends on the plant's ability to produce at costs equal to, or below, the competition. The solution toward getting costs down is usually one of scaling up the plants to get the most tons through at the lowest possible cost. Control of these plants has been an art. Few of them are well instrumented because until a few years ago reliable instrumentation was non-existent. International Minerals and Chemical Corporation was a pioneer in applying computer techniques to ore reserves analysis and mine planning and the success in these areas led to the question of whether we could not extend the advantages of computer processing into the plant itself. There was a great deal of doubt on the operator's end that this could be done successfully because of the lack of instrumentation and the fact that plant control was largely an art that was learned only after many years of experience. However, in 1965 the instrumentation picture began to look up and the new generation of process computers just coming on the market were considerably lower in cost than the previous ones. A preliminary study of the installation costs and the probable benefits that could be realized from computer control convinced us that a process control computer should be seriously considered for a new phosphate mining plant which was being designed.

Jan 1, 1969

By P. J. Dean

This Paper contains a comprehensive survey of the known electron-hole radiative recombination mechanisms in the family of III-V compounds. Because of space limitations, the luminescence properties of each III- V compound are not reviewed separately and exhaustively. Instead, the different known types of recombination processes are discussed in turn and exemplified with reference to the III- V compound in which they were first recognized, or are best understood. Electron-hole recombinations usually occur predominantly at impurities or lattice defects either introduced de1iberately or inadvertently present, but radiative intrinsic interband electron-hole recombinations, which occur in perfect crystals, have been observed. Recombination processes which involve the participation of impurities or lattice defects ("extrinsic" recombinations) considered include transitions in which a) free carriers recombine with carriers trapped at impurities ("free to bound" transitions) , b) electrons bound at donor impurities recombine with holes trapped at acceptor impurities ("donor-acceptor pair" recombinations), C) excitons bound to charged or neutral donor or acceptor impurities recombine radiatively (both "resonance" and "two-electron" "bound exci-ton" transitions have been observed), d) excitons bound to neutral donor or acceptor impurities recombine non-radiatively (an example of an "Auger" recombination), and e) excitons bound to impurities with the same number of valence electrons as the host atom which they replace ("isoelectronic " traps) recombine radiatively. In addition, Auger recombination processes involving one or more free carriers have been observed. These extrinsic processes all involve impurities which are present as point defects. Some apparently well-authenticated examples of the recombination of excitons bound to complex impurity-lattice defect centers including nearest-neighbor donor-acceptor pairs are also discussed. Identificalions of the transitions involved in stimulated emission from the direct gap III-V compounds are briefly reviewed. Although the examples of these recombination mechanisms are selected from the III-IV compounds ia this review, these processes have quite general relevance in semiconducting crystalline solids; irrdeed most of them have also been identified in the 11- VI compounds and elernental semzconductors. THE development of crystal growth and purification techniques in recent years and concurrent advances in the understanding of physical processes in solids has accelerated the development of a wide variety of solid-state electronic devices of proven utility. These de- vices are generally used for switching or amplifying operations in electrical circuits. Most solid-state circuit elements are very photosensitive. This photo-sensitivity is generally undesirable and the single-crystal chip forming the active portion of the solid-state device is mounted in an opaque container. The photosensitivity is made use of in phototransis-tors and photodiodes, which are among the most sensitive detectors of electromagnetic radiation particularly in the near infrared.' In these devices, light is converted into electrical power. The solid-state lamp utilizes the inverse effect, namely the conversion of electrical power into light. There is an increasing tendency to use single-crystal diodes rather than the earlier electroluminescent cells in which the active material is present as a powder embedded in a suitable dielectric.' The radiation is emitted at a rate far in excess of the thermal equilibrium rate for the frequencies and temperatures involved; i.e., luminescence occurs. The development of practically efficient solid-state lamps is at an early stage compared with solid- state circuit elements or even photodetectors. Considerable progress has been made in recent years, however.3 The present review is devoted to a survey of the radiative recombination processes in the semiconducting compound crystalline solids formed from elements in groups I11 and V in the periodic table. These materials exhibit the full range of known recombination processes in solids. In fact many of these processes were discovered in 111-V semiconductors. Nonradiative recombination processes, which control the lutninescence efficiency, are also discussed. Luminescence is efficiently excited in semiconductors through processes which produce large excess concentrations of free electrons and holes in the energy bands of the crystal. Transitions induced by lattice defects or impurities usually predominate in the recombination process. By contrast, luminescence in the conventional fluorescent lamp is excited by optical absorption at the luminescent impurity center itself (the activator) and/or at a second type of impurity center (the sensitizer). This latter type of photoluminescence process, occurring in doped ionic crystals with wide band gaps, is outside the scope of this review.4 I) ENERGY BAND DESCRIPTION OF ELECTRON STATES IN CRYSTALS The energy band description of the energy states available to an electron in a crystal forms the basis of our understanding of the empirical division of crystalline solids into metals, semiconductors, and insulators in accordance with their electrical and optical properties.' Nonmetallic crystals have a finite energy gap between the highest energy band which is

Jan 1, 1969

By E. Breinan, M. Salkind

Al3Ni whiskers were chemically extracted from unidirectionally solidified Al-A13Ni eutectic ingots, bent into loops, and heated for 0.1 to 10 hr at 320°, 415", and 510°C. The initial strains ranged from 0.003 to 0.055. In all cases, permanent plastic deformation was noted after heat treatment. The deformation consisted of relatively uniform bending at low stresses and temperatures and short times and kinking followed by fracture at high stresses and temperatures and long times. After kinking, the whisker segments adjacent to the kinks were found to have straightened, which is evidence of a dislocation condensation mechanism. The range of temperatures and strains at which time dependent plastic deformation was found indicates that creep of whiskers probably plays a role in the creep of A13Ni whisker-reinforced aluminum. WHISKERS may be defined as nearly perfect single crystals which exhibit high strength. Because they can support high stresses at relatively low strains, they have been successfully employed in reinforcing metals at both ambient and elevated temperatures. In studying the creep behavior of A13Ni whisker-reinforced aluminum at elevated temperatures,1,2 it was noted that the composites exhibited measurable creep deformation. This investigation of the creep relaxation of individual A13Ni whiskel, extracted chemically from the composite was initiated to determine if creep of whiskers could con. "bute to the overall creep of the composite material. Many observations of plastic deformation of metal and halide whiskers have been made. Brenner3-8 noted that copper, silver, and iron whiskers exhibited heterogeneous plastic deformation at room temperature when strained beyond their yield points. Gyulai9 and Gordon10 observed plastic deformation of relatively large (>3 µ) NaCl and KC1 whiskers, although the smallest, most perfect whiskers were completely elastic. Eisner" noted plastic deformation and microcreep of iron and silicon whiskers at room temperature after straining beyond the yield point. Whiskers reported to exhibit creep at stresses below the yield point were zinc1'-" and Silicon.15 Cabrera and price" observed some zinc whiskers which crept at room temperature after a short incubation period but then stopped creeping after a short time. Because some of their specimens exhibited no creep, they concluded that those whiskers that crept were relatively imperfect. Pearson, Reed, and Feldman15 observed similar creep behavior of silicon whiskers at 800°C. They also concluded that creep of the whiskers was a result of imperfections in their crystals. Brenner16 observed delayed failure of A12O3 whiskers at elevated temperatures but found no evidence of plastic deformation up to 2030°C (99 pct of E.EREINAN and M.SALKIND,JuniorMembers AIME,are Research Scientist and Chief, respectively, Advanced Metallurgy Section, United Aircraft Research Laboratories, East Hartford, Conn. Maunscript submitted April 5, 1968. IMD the melting temperature). Brenner also noted7 that some copper and iron whiskers exhibited delayed kinking above 350°C while others did not. One can conclude from these observations that small relatively perfect whiskers could exhibit completely elastic behavior during sustained elevated-temperature loading of composites. Since A13Ni whiskers tested in both bending and tension were found to exhibit no evidence of plastic deformation at room temperature'7'18 this study was initiated to determine whether or not creep of A13Ni whiskers occurred at the elevated temperatures at which creep in the composites was observed. Whiskers were chemically extracted from ingots of unidirectionally solidified A1-A13Ni eutectic, constrained in bending to various elastic strains and heat-treated. The bending constraints were removed after heat treatment and the amount of permanent set was taken as a measure of the time-dependent plastic deformation. EXPERIMENTAL PROCEDURES Ingots of eutectic Al-A13Ni containing nominally 6.2 wt pet Ni were unidirectionally solidified at approximately 11 cm per hr using a process described elsewhere.19,20 The starting materials were 99.99 pct pure. Cylindrical sections cut from the center of each ingot were placed in a 3 pct aqueous solution of hydrochloric acid and the whiskers were extracted as described previously.17 The whiskers nearest the surface were blackened somewhat due to overexposure to the acid while the center of the ingot was being dissolved These partially attacked whiskers were discarded. An intermediate zone of silver-gray-colored whiskers was collected and stored in methanol for use in relaxation experiments. Individual long pieces of A13Ni whiskers were placed on Fisher Precleaned Microscope Slides. These normally straight whiskers were bent elastically into arcs or loops of varying radii by manipulating their ends with a slender probe. The mass attraction between the whisker and the probe was sufficient to cause the whisker to follow the probe. The whiskers were retained in the elastic bend by the surface tension of a fine residual film on the slides. By using long whiskers, the action of the surface tension on the unlooped ends of the whisker allowed high elastic strains to be maintained in the loops. After each whisker was bent, a photomicrograph was taken for use in measuring the bending strain. The range of strains studied was 0.003 to 0.055. The bent whiskers were then encapsulated in Pyrex tubes at pressures between 10"6 and 5 x 10"6 mm of mercury and heat-treated at 320°, 415°, and 510°C (respectively 53, 61, and 70 pct of the peritectic decomposition temperature). After each heat treatment, the liquid film on the slides was found to have dried, but the whiskers were held in their original shapes by a residue on the slide. The minimum radius of curvature of each bent whisker was measured before and

Jan 1, 1969

By John M. Karpinski, David S. Cahn

A new device based on a constant rate of loading has been developed for the compression testing of green and dry pellets. This device has a lower test variation for green pellets than the existing constant deformation rate tester. While the test variations for dry pellets are similar for both types of machine, the new tester is sensitive enough to measure dry pellet deformations of 15 µ in. for cyclic loading studies. In the study discussed here, the compressive load at which a pellet breaks proved to be a normally distributed random variable, and the load-deformation relationship was found to be linear for dry pellets but not for green pellets. The paper emphasizes the need for a standardized test procedure throughout the industry. For many years the green and dry compressive strengths of pellets have been considered as possible criteria of pellet performance during induration. Little attention, however, has been given to standardizing the unfired pellet compressive strength test or to determining the characteristics of this test. The purpose of this study was to compare the constant deformation rate test with constant loading rate

Jan 1, 1969

By Jaakko Kajamaa

Neutron diffraction was applied to determine sheet textures by the transmission method. Cold-rolled and recrystallized copper sheets were investigated. The amount of cube texture was determined for three compositions, in which the phosphorus content was, respectively, 0, 0.005, and 0.03 wt pct. The heat treatment was in every case 8 sec at 650°C. In the two latter cases the cube texture was prevented. In addition a comparison with the X-ray diffraction transmission method was made with the 96 pct cold-rolled copper sheet. Outer parts of both (111) pole figures can be considered to be rather identical. This is seen from the fact that the intensity ratio ITD/120" was 0.45 for neutron diffraction and 0.40 for X-ray diffraction. Differences between the methods were discussed in detail. Features peculiar to neutron and X-ray diffraction in texture studies were listed and compared. In this work neutron diffraction was applied to determine sheet textures. Specifically, it was desired to ascertain whether this method can be used to reveal differences when compared to other methods. In addition, the amount of the cube texture in copper sheets was determined as a function of phosphorus content. Previous applications of neutron diffraction to texture problems include the following: nickel wires,' wire of some bcc metals,' and uranium bars.3 In the neutron diffraction technique the greatest difference is in the sample—its method of production and its volume. A sample needs no treatment and its volume is roughly 105 times larger than the volume of an X-ray diffraction sample. The cold-rolled sheet was investigated both by neutron diffraction and by X-ray diffraction, because it is expected that, due to large number of defects, possible differences in the results of the two methods would be revealed. It is a well-known fact that X-ray lines show broadening when cold-worked. Analysis has shown that this is based chiefly on small crystalline size, micro-stresses, and/or faults.4'5 Neutrons are sensitive to the above-mentioned disturbing factors as well, but circumstances in diffraction are different from the X-ray case. Because the sample represents a larger volume, the result is an average over that volume. In addition, it can be assumed that the sample has preserved its original structure, because it needs no special preparation. The particular limitation of neutrons is the relatively low neutron intensity available from nuclear reactors. This decreases the resolution as compared to the X-ray diffraction methods. Furthermore, absorption mainly reduces diffracted X-ray intensity, while multiple scattering effects, i.e., secondary extinction, disturb neutron diffraction. SO neutrons and X-rays behave in a different way when interacting with matter. As in other structural investigations, one can utilize this difference in texture studies as well. One cold-rolled and three recrystallization textures in copper sheets were investigated by neutron diffraction. The samples were produced at the Outokumpu copper factory to the specifications shown in Table I. The paper is divided into five parts. The first deals with the theory of the measurement. In the second, experimental procedures are described. Results are presented in the third part. Both cold-rolled and re-crystallized samples are studied. Discussion is in the fourth part, and finally in the fifth part some conclusions are drawn. 1) THEORETICAL CONSIDERATIONS Properties peculiar to neutron diffraction are the following: a) the scattering length varies greatly between one element and another; b) many of the elements do not absorb neutrons appreciably. In this connection it is of primary interest to know the interaction of neutrons with lattice imperfections. As with X-rays this problem leads to diffraction analysis of deformed and recrystallized metals. From the physical point of view the main difference is that neutrons are scattered by nuclei (magnetic scattering is not considered here), whereas X-rays are scattered by electrons. The features peculiar to neutron and X-ray diffraction methods in texture studies are listed in Table 11. Pole figures are an important tool in performing structural analysis of deformed or recrystallized metal. Present texture research technology requires pole figures which are as precise as possible. The choice between these two methods depends on the technical information which is required. The X-ray diffraction transmission technique may give results which are not necessarily representative of the average physical state of the sample. Although foil samples normally contain enough crystallites for diffraction, they may not necessarily represent the whole structure. An example of this problem is the frequently observed difference between the "surface" and the "inside" texture of a sample. The production of foil samples may disturb the original structure of the parent material. The selection and orientation of the foil from the sample is quite arbitrary. Normally, a highly deformed piece of metal has several texture components. Different components are deformed in a slightly different manner. This is a re-

Jan 1, 1969

By William C. Peters

"A large proportion of the earth's surface is blanketed by young sedimentary formations and by recent lava flows. How many Guanajuatos lie concealed beneath the rhyolitic capping of the Sierra Madre of Mexico? How many Kirkland Lakes are under the drift cover of the Canadian Shield? How many Wilunas are still hidden by the alluvium of the desert of Western Australia? How many ore deposits lurk underneath the basalt-covered plateaus of the Columbia River region? If erosion at Goldfield, Nevada, had stopped 100 feet higher, probably no ore would have been exposed. How many Goldfields are still awaiting discovery?" --Hugh Exton McKinstry, 1948

Jan 1, 1969

By Howard S. Avery

The wear resistance of an alloy in heavy mill liner sections may be quite different from that of the same alloy in small balls and other light sections. This fact was established by means of a well standardized laboratory test that was validated for ball mill service. The salient properties of mill liner alloys, including austenitic manganese steels, medium alloy hardenable steels, and abrasion resistance cast irons are described, critically compared, and quantitatively ranked in terms of mill liner service. Where they are tough enough the high-chromium and other martensitic cast irons (e.g. Ni-Hard) promise maximum economy, but their section sensitivity is a limitation. To overcome this an extensive research program studied over a hundred experimental alloys, ranking them for heavy section abrasion resistance by means of the laboratory test. Computer analysis of the results provided a parabolic formula in terms of composition, the apexes of the parabolas providing optimum wear resistance. From the extensive family of parabolas one apex was selected for intensive study in experimental liners, pilot plant production, development of quality controls, and finally full scale production. This is a 19% chromium iron critically alloyed with nickel and molybdenum and hardened by heat treatment. It has excellent resistance to various types of abrasion, but its chief advantage is in heavy mill liner sections, where it has about 25% better abrasion resistance than the best of the quality controlled chilled Ni-Hards. It is also tougher. After production problems were solved, a number of ball and rod mill tests were arranged on a guaranteed performance basis. Two of these, representing about 138,000 pounds of mill liner castings, have recently confirmed in service the superiority that was predicted by the laboratory tests.

Jan 1, 1969

Reports on process control computer projects at the Kamioka Plant are summarized from the Japanese technical literature (see references). Fluidized Bed Roaster and Sulfuric Acid plant1 A small process control computer (Yokogawa CCS-200 with an OKITAC 5090P 8K central processor) was installed in the Kamioka smelter in the summer of 1964. A year-and-one-half installation project followed, which successfully brought the roaster and acid converters under computer control. The process plant consisted of two 130 RPD fluosolids roasters and two Monsan to acid units. The roasters are charged with lead-zinc concentrates with SO2 from the roaster processed to sulfuric acid. The computer system provides the following functions: 1) log data from the plant--the input is taken from 50 analog signals, 130 high-low digital alarm points, and 50 analog high- low alarm points; 2) set-point control on 18 control loops; 3) direct digital control (DDC) on eight control loops for which conventional controllers were difficult to adapt due to abnormal loop characteristics or delay times; 4) execution of a safe shut-down procedure

Jan 1, 1969

By S. C. Sircar, B. K. Dhindaw

KINETICS and mechanism of sulfation reactions have been studied extensively. Qualitative and quantitative data are reported for the kinetics and mechanism of sulfation reaction of copper oxide pellets;''2 yet it remains a controversial Subject. The mechanism and kinetics of the sulfation of zinc oxide powder (B.D.H. analar quality) were studied by gravimetric technique. A spring of high-carbon steel wire with accuracy well within 0.2 mg was used for measuring weight change. The sample was taken in a Pyrex glass bucket, hanging freely inside a Pyrex glass tube reactor, with a gold wire attached to the spring, the reactor being surrounded by a movable furnace (double wound type) with a temperature control within *5"C. Flow of oxygen, 60 cu cm per min, and sulfur dioxide, 45 cu cm per min, were measured through calibrated flowmeters and the mixture dried over PZ05 before entering the reactor. The experimental results are presented in Figs. 1 and 2. The plot of weight change of zinc oxide, giving the amount of zinc sulfate formed, was found to be linear over the temperature range of 500" to 700° C and up to a conversion of approximately 60 pct, as beyond it they divert from linearity.' The rate of sulfation was found to be affected by total flow rate of gases at a fixed ratio of SO2/O2, up to 60 cu cm per min, and was found to be linearly dependent on quantity of total powdered sample taken. The plot of rate of sulfation of zinc oxide, 70 mg, with varying amounts of vanadium pentoxide, at a constant ratio of gases as mentioned above, and at a constant temperature of 625"C, was also found to be linear as seen in Fig. 2. Extrapolation to zero V2O5 addition gives the same rate of sulfation, as in case of pure zinc oxide, 70 mg. Vz05 was prepared by heating ammonium vanadate at 600°C for 15 min in a muffle furnace. The available literature points out that the theory of sulfation that has received the maximum support postulates the following mechanism for sulfation of ZnS: 2ZnS + 30, = 2Zn0 + 2SOZ; the ZnO formed acts as a catalyst for the reaction, 2 S02 + O2 = 2S03. This SO3 reacts with ZnO to give zinc sulfate. It is suggested here that the above widely supported mechanism is operative in the sulfation reaction and that the rate-controlling step in the sulfation reaction of ZnO is the formation of SO3 from SO, and 0,. The authors are carrying on further work in this line, and the details will be published later. The authors wish to acknowledge the facilities provided and the help extended by Prof. P. R. Dhar, Head, Department of Metallurgical Engineering, and the permission granted to publish this note by the Director, I. I. T., Kharagpur.

Jan 1, 1969

By A. M. Mirani

The Mine Planning System consists of two parts: 1. A Sales Forecast (Sales Planning) 2. A Production Planning. The mathematical methods of the sales forecast are the exponential smoothing and a method with Markov-Chains. By these methods the quantity of material (ore, coal) will be calculated for the time planned. These quantities constitute the points in the production-planning. In the production-planning , special kinds of networks are used for calculating the resources-equipment required, labor and costs. A special routine optimizes the sequence of the mining areas within the mine on the basis of the lowest costs. The resources can be limited. The activities will be shifted when the demand exceeds this limit. The basis of the production-planning are computer files, in which the geological data and economical evaluations are stored.

Jan 1, 1969

By D. S. Kingery

Experiments initiated by the Bureau of Mines on August 26. 1969, and recent work of others, have demonstrated the effectiveness of ventilation for controlling concentrations of respirable coal mine dust. Substantial reductions in dust concentrations have been attained by increasing the volume and rate of air movement across the face and by controlling the airflow pattern. Ventilation experiments conducted by the Bureau using high-pressure fans as auxiliary ventilation units showed that lace-generated dust could he effectively controlled in five mines employing continuous mining machines. Additional data was obtained on industry installations in two mines using similar ventilation systems. By maintaining an airflow approaching 100 fpm across the entry, the experimental system reduced the concentration of respirable dust by factors as great as 6.4. In all mines where the system was used the face-generated dust concentrations were reduced to below 3 mg/m3. Total respirable dust in two cases was above the 3 mg/m value because of the dust content of the intake air. In some mines. depending upon the type of coal being mined and other dust control factors in use, it was possible to Obtain concentrations of less than 2 mg/m Although the technology for the application of the dust control system investigated is readily available, it is evident that additional engineering studies should he made in each mine where the system is to be applied.

Jan 1, 1969

By A. Mitchell

An approximate phase diagram has been developed for the CaF2-CaC2 system, indicating a eutectic point at 1240°C, Ncac2 = 0.13, and no detectable solid solution in either phase. The liquidus line is shown to correspond to a simple c22- ion in solution. A thermo-chemical study of&apos; the reaction between carbon-saturated Ni-Ca alloys and CaC2-CaF2 liquids indicates that lhe Raoullian activity coefficient of CaC2 in dilute solution in Cap2 al 1500°C lies between 8 and 10. Some effects of the stabilily of Cap2-CaC2 solutions at high temperatures on electroslag remelting praclice are outlined. THE alkaline earth acetylides. MIIC2, have a reasonably high thermochemical stability at high temperature in the solid state,&apos; with the exception of magnesium, which forms an unstable acetylide at low temperatures (-500°C) and a carbide, Mg2C3, in the range 700&apos; to 1000°C. The acetylides of calcium and barium have been shown to have limited solubility in their respective chlorides,&apos; and further these solutions contain the acetylide as a C: ion.&apos; The equivalent magnesium solutions have not been studied. Although calcium "carbide" is used as a desulfuriz-ing reagent in steelmaking. and is possibly present as an acetylide-oxide phase in very basic electric arc practice slags, the acetylide ion appears to be substantially unstable in a silicate slag.* As a conse- *This instability arises from equilibria in the reaction: CaC2 + CO = (Ca0) + 3C where the low intrinsic solubility of CaC2 in silicate lattice, and the low activity of CaO in a silicate solution where CaO/Si02 < 1, combine to give a very small equilibrium concentration of CaC2 in solution in such silicate slags at temperatures in the region of I 500°c, even under carbon-saturated conditions. Under highly basic conditions, a liquid CaO-CaC2 phase may separate from the silicate system quence of this, the possibility that reactions involving CaC2 in silicate solutions are of importance to general steelmaking practice is remote. However, in operations involving a slag primarily based on a halide, or alkaline earth oxide, we must take into account the possibility that CaC2 will appear in quantities sufficient to significantly affect both the chemical and physical properties of the slag. The work outlined below presents a study of the CaF2-CaC2 system intended to provide sufficient data to allow an estimate of the importance of this system to electroslag remelting and welding practice. However, we should indicate at this point that there will be other processes, e.g., heat treatment, flux cleaning of castings, fused salt electrolysis, and so forth, where alkaline-earth halide fluxes are in contact with carbon, graphite, or carbides, and where halide-acetylide solutions must be taken into account. EXPERIMENTAL 1) Structural Studies. In view of the difficulty ex-perienced in handling CaC2 prepared from calcium turnings and propane gas at 700°C, it was decided to use solutions prepared directly in the equilibration apparatus, Fig. 1. The starting materials were: a) Ni-Ca-C alloy, prepared by adding calcium to liquid nickel held under calcium fluoride in an induction-heated graphite crucible; b) calcium fluoride, prepared by fusing calcium fluoride powder (British Drug House "EXTRA PURE") calcium fluoride in an induction-heated graphite crucible, in air, followed by electrolysis between graphite electrodes at 1 amp cm-2 density, for 10&apos; coulombs per g CaF2. This procedure decomposes the CaO produced by hydrolysis during the fusion step, replacing it by CaC2; Ca2+ + 2e-Ca*(l) Ca*(l) + 2C(gr)-(CaC2)caF2 O2- -2e-O*(g) O*(g) +C(gr)-CO(g) This results in a composition of between 2 and 5 wt pct CaC2 in CaF2. Fifty grams (in lumps) of this material were placed in a graphite crucible, together with Ni-Ca-C alloy (averaging 20 wt pct Ca), and the equilibration apparatus assembled. The alloy reacted with the crucible at high temperature to give CaC2, which dissolved in the calcium fluoride solution to give the desired composition. Cooling curves were plotted manually for these liquids, with rapid stirring and CaF2 seeding to minimize supercooling, and using a Pt/Pt 13 Rh thermocouple calibrated on the freezing points of nickel and copper. This gave a reproducibility of ±0.l°C. and an absolute accuracy of the thermocouple of ±l°C. An example curve is shown in Fig. 2, with the CaF2 end of the binary system in Fig. 3. The CaF2-CaC2 ingots were crushed, under dry nitrogen, and sampled for chemical analysis and X-ray examination. Analytical details are given in the Appendix. Powder diffraction data indicated that the only phases present in all samples examined were calcium fluoride and tetragonal (Types I and 111) calcium acetylide,4 with no evidence of solid solutions or compound formation. 2) Thermochemical Studies. The apparatus used to obtain activity data on CaC2 in these systems is shown in Fig. 4. It consists of an arrangement whereby the graphite crucible and its contents (CaF2-CaC2. Ni-Ca-C) can be rapidly cooled without exposure to air. Trial experiments to determine an equilibration time by ap-

Jan 1, 1969

By R. Ward Grosz

The Robinson mining district in east-central Nevada is itself a century of study in the changing economics of the mining business. It began as a boom and bust area. In the district today, just west of Ely, Nev., the hills are pockmarked with the tunnels and shafts sunk in a frantic scramble for gold and silver before the turn of the century. But as the economics of dwindling reserves, rising costs, and changing markets were stamping out the efforts of the gold and silver seekers, copper took over as the king of the Robinson district. Today, Kennecott Copper Corp. has four open pit mines in the district and is planning a fifth. From these mines, Kennecott produces nearly 40,000 tpy (tons per year) of copper. In its hundred years of history, the district has produced more than $1 billion in mineral values, a richer treasure than that from the more famed Comstock Lode of Virginia City, Nev. Prospectors had reported copper outcroppings in the Robinson district as early as 1872. But the first significant copper orebody was not discovered until 1901. In that year, Dave Bartley and Edwin Gray exposed the top of the porphyry orebody that would become the Ruth mine in a shaft at a depth of 120 ft. Subsequently, other larger orebodies were discovered nearby which have resulted in this area being one of the leading copper producers in the country for some 60 years. Following a period of development and exploration, the Ruth mine started production in 1915 and continued as a prosperous underground mining operation until 1948. The mining industry in Nevada experienced the same increasing cost of labor and supplies that all other mining areas had to contend with, and by 1948 the Ruth mine was no longer profitable. The mine was closed down on August 8 of that year. Now, two decades later, the mine is to produce again. The key factor in the case history of

Jan 1, 1969

By E. S. Fisher, L. C. R. Alfred

The elastic anisotropy factors, c4,/c6,, c3,/cll, and c12/cl,, for hcp metal crystals vary significantly among the dgferent unalloyed metals. Significant variations with temperature are also found. The effects of elastic anisotropy on the dislocation in an elastic continuum with hexagonal symmetry have been investigated by computing the elasticity factors for the self-energies of dislocations in fourteen different metals at various temperatures where the elastic moduli have been reported. For most of the metals the effects of the orientation of the Burgers vector, dislocation line, and glide plane are small and isotropic conditions can be assumed without significant error. Significant effects of anisotropy are, however, found in Cd, Zn, Co, Tl, Ti, and Zr. The elasticity factors have been applied in the calculations of dislocation line tensions, the repulsive forces between partial dislocations, and the Peierls-Nabarro dislocation widths. It is predicted that the increase in elastic anisotropy with temperature in titanium and zirconium makes edge dislocations with (a), (a + c), and (c) Burgers vectors unstable in basal, pyramidal, and prism planes, respectively. The probability of stacking faults forming by dissociation of Shockley partials in basal planes also decreases with increasing c4,/c6, ratio, when the stacking fault energy is greater than 50 ergs per sq cm. The widths of screw dislocations with b = (a) in titanium and zirconium increase very significantly in prism planes and decrease in basal planes as c4,/c6, increases. The effects of elastic anisotropy on various dislocation properties in cubic crystals have received considerable attention during the past few years. In the case of cubic symmetry the departure from isotropic elasticity depends entirely on the shear modulus ratio, A = 2c4,/(cl, —c12); i.e., the medium is elastically isotropic when A = 1. Foreman1 showed that an increase in the ratio A produces a systematic lowering of the dislocation self-energy for a given orientation and Poisson&apos;s ratio. ~eutonico~, has shown that large anisotropy can have a marked effect on the formation of stacking faults by the splitting of glissile dislocations in (111) planes of fcc and (112) planes of bcc crystals. ~iteK&apos; made similar calculations for (110) planes of bcc metals. Both studies of bcc metals showed that the large A values encountered in the alkali metals tend to reduce the repulsive forces between Shockley partial dislocations. In fcc metals, however, A does not vary over the large range encountered in bcc metals; consequently, the effect of A on the forces between Shockley partials is masked somewhat by the differences in Poisson&apos;s ratio between metals. The effect of A on the line tension of a bowed out pinned dislocation has also been investigated for cubic crystals, first by dewit and Koehler5 and more recent- ly by Head.6 In both cases the line energy model is applied and the core energy is not taken into account, thus making the conclusions somewhat tenuous with regard to the physical interpretation. Nevertheless, the fact that a large A decreases the effective line tension is clearly evident and the tendency for large A to produce conditions that make a straight dislocation unstable (negative line tensions) also seem evident. Head, in fact, shows visual microscopic evidence that stable V-shaped dislocations occur in 0 brasse6 For hcp metals the definition of elastic anisotropy is more complex and, furthermore, significant deviations from an isotropic continuum are found among a number of real hcp metals, especially at higher temperatures. The present work was carried out to survey the effects of elastic anisotropy on the elasticity factors, K, that enter into the calculations of the stress fields around a dislocation core. Some isolated analytical calculations have previously been carried out for several hcp metals but they are restricted in the dislocation orientations and temperature.8&apos;9 The present computations are based on single-crystal elastic moduli that have appeared in the literature and consider various orientations requiring numerical computations. The results are then applied to survey the effects of temperature on the dislocation line tension and dislocation splitting in hcp metals. PROCEDURE Anisotropy Factors. The degree of elastic anisotropy in hcp crystals cannot be described by a single parameter, such as the A ratio in cubic crystals. The following three ratios must be simultaneously equal to unity in order to have an elastically isotropic hexagonal crystal: The magnitudes of these ratios at several temperatures, as computed from the existing data for the elastic moduli of unalloyed hcp metals, are given in Table I. There are no cases of complete elastic isotropy, but the large anisotropy ratios encountered in the cubic alkali metals are also missing. There are, however, several significant differences among the hcp metals, the most notable being the relatively small A and B ratios in zinc and cadmium and the differences in the magnitudes and temperature dependences of A. It has been noted that the temperature dependence of A has a consistent relationship to the occurrence of the hcp — bcc tran~formation. For cadmium, zinc, magnesium, rhenium, and ruthenium, A is less than unity at 4&apos;~ and, with exception for rhenium, decreases with increasing temperature. In the case of rhenium, A has essentially no temperature dependence between 923&apos; and 1123"~, so that it is clear that A does not approach unity at higher temperatures. Cobalt is similar to the above-mentioned group of metals in that it also does

Jan 1, 1969