Search Documents

By E. T. Turkdogan, L. S. Darken

Using the quadratic formalism, thermodynamic equations are derived for the composition dependence of the heat and entropy of mixing. The applicability of these equations is confirmed by available experimental data on the activities and heats of mixing for binary metallic systems of Group ZZB elements. In a recent paper arkeen' introduced a quadratic formalism describing the composition dependence of the activity coefficient in the terminal regions of binary metallic solutions. That is, in the terminal region, which may extend to as much as 60 at. pct, the logarithm of the activity coefficient, log y,, of component 2 is a linear function of (1 - N,)' where N2 is the atom fraction of component 2. Similarly, for the other component, log yl is a linear function of (1 - N,)'. A number of iron-base binary liquid alloys were shown to obey this quadratic formalism. arkeen' extended this formalism also to any corner of a ternary system and showed that the activity coefficients of the components 1, 2 and 3 (1 is taken as the solvent) can be represented by quadratic terms involving five parameters, four of the binaries and one for the ternary system. Numerous examples given by arkeen' demonstrated the general applicability of the quadratic formalism to iron-base systems over a wide composition range. In this paper further examples are given of binary liquid systems (Group IIB elements, Zn, Cd, and Hg) and of several solid solutions, again demonstrating the appropriateness of this concept. A further purpose of this paper is to extend the quadratic formalism to the enthalpy and excess entropy of binary metallic solutions and to test the equations so found using available experimental data. QUADRATIC FORMALISM FOR HEATS AND ENTROPIES OF MIXING OF BINARY METALLIC SOLUTIONS The following equations, reproduced from Darken's paper, are for the two terminal regions of binary systems. at infinite dilution and a's are temperature dependent parameters to be determined from the experimental data. Although the quadratic formalism is an assumed representation of the data, Eqs. [I] to [4] are thermo-dynamically consistent with the Gibbs-Duhem relation and satisfy Raoult's and Henry's laws as limiting cases. As pointed out previously,' the following form of the Gibbs-Duhem equation facilitates the integration in general but particularly in regions I and 11, where each of the derivatives is constant. The partial molar enthalpy of solution i, (and i; the value of i, at infinite dilution) are related to the activity coefficients y, and y," by the thermodynamic relation Differentiating Eq. [l ] with respect to 1/T and substituting the above thermodynamic relation gives for region (I) It is reasonable to assume that over a temperature range of experimental interest, the enthalpy of mixing is essentially independent of temperature, implying from Eq. [7] that the derivative da,,/d(l/) is also independent of temperature. On the basis of this argument, the temperature dependence of a has the form where £ and S have the units of enthalpy and entropy respectively; they are characteristic parameters for a terminal region of a binary system, e.g. for region (I), C12, S12 and for region (II), d:,,, S2,. Using this equation gives for dff ,/ d(l/), From Eqs. [7] and [9] an expre_ssion is obtained for the composition dependence of L,. Similar calculations are made for El and the results are summarized below for the two terminal regions. For region (I), The corresponding expressions for the molar heat of solution, AHM, are readily obtained from the above equations for the two terminal regions: For region (I),

Jan 1, 1969

By Daniel T. O’Brian

Exploration targets and results in the mining industry are commonly summarized in terms of tonnage and grade. Business appraisals require, as additional information, the expected profit or loss implied by the physical summary. The early incorporation of knowledge gained through financial analysis computations can provide a means for economically resolving many common exploration and development problems. Examples of such applications from the activities of exploration planning, reconnaissance, land acquisition, and development planning are presented in this paper.

Jan 1, 1969

By Ivan Simon, R. K. McConnell

Anticipating the availability of tiltmeters suitable for use in boreholes, this article proposes a method of using one or more of these meters to determine in situ stress distribution before and after mining operations. Several ways of using relief techniques to measure in situ stresses in rocks have been developed. These techniques, summarized by Merrill,1 involve measuring deformations which take place when a specimen of rock is wholly or partially isolated from the stress field in the surrounding rock. Measurements of rock deformation caused by stress relief from mining operations can, in principle, also be used to estimate in situ stress distributions. Müller2 has mentioned experiments being carried on in Austria with a "deformation indicator" to determine the tilting of holes drilled before a mine opening is made. Similar work using borehole extensometers has been reported by Potts? and Duvall4 has called attention to the possible use of tiltmeters in making these measurements. Considerable attention is now being paid to the use of tiltmeters in detecting rock deformation associated with fault movements, earthquakes, earth tides, etc. The instruments used for these measurements have usually been of the mercury tube, water tube, or quartz fiber type, but because of their large size, and/or fragile nature, such instruments would not be suitable for use in mining stress measurements. Recent instrumentation developments, however, give promise that rugged, sensitive tiltmeters small enough for use in boreholes may soon be available.' In anticipation of these developments, this article presents a number of calculations of the possibility of using one or more tiltmeters emplaced in a drill hole prior to mining operations to determine the in situ stress distribution both before and after a mining operation. Consider point p (x, z) near a tunnel of radius a

Jan 1, 1969

By E. W. Coderre, R. C. Baxter

"This paper describes the townsite of Wabush and the two railways operated by Wabush Mines for the loading and unloading of iron ore concentrate. The town of Wabush is located approximately 200 air miles north of Sept-Iles, Quebec and is in the Province of Newfoundland and Labrador. Construction of the town-site began in 1961 to provide housing accommodation for the construction force and permanent employees in the mining and milling operations located 4 miles away. Wabush Mines operates two short railway lines in loading and unloading concentrate between the concentrator, located at Wabush, and the pellet plant at Pointe Noire, Quebec. Both of these railways connect with the main line of the Quebec North Shore and Labrador Railway and provide a shuttle service between the two phases of the operation."

Jan 1, 1969

By W. E. Anable

A 180° magnetic deflection residual gas analyzer mass spectrometer with a mass range of 2 to 200 amu was used to study the nature of gases evolved during arc and electron-beam melting of certain reactive and refractory metals. The partial pressure of residual gases over molten Mo, Hf, Ti, and Fe, was found to be similar: Water and hydrogen were evolved from the samples and from the furnace components, carbon dioxide and carbon monoxide resulted from deoxidation of some of the melts. Argon and acetone were residuals in the system, and methane was a decomposed organic compound from the oil diffusion pump.

Jan 1, 1969

By Paul A. Filteau

Asbestos ranks among the leading minerals produced in Canada. It is also mined in Russia, Rhodesia, South Africa, Cyprus, Italy, the U.S.A., Japan, China and several other countries. The most abundant variety, chrysotile, and also the most valuable form of asbestos produced, makes up 90% of the world's supply. In Canada, chrysotile is found in the provinces of British Columbia, Ontario, Newfoundland as well as in Quebec, the latter accounting for almost 90% of all the fibre produced in this country. A number of developments emerging this year could make 1968 a record production and export year for Canada's asbestos mining industry. Asbestos fibre consumption in increasing in the U.S., Canada, up 10% to date this year, Japan and in Latin America. Demand in Western Europe is again on the upswing, following a cut-back last year. As a result, shipments from Canadian mines for the first eight months of this year reached some 916,968 tons versus 873,402 in 1967, an increase of 43,566 tons or 5%. Indications are that Canadian asbestos production will for the first time ever top 1.5 million tons in 1968.

Jan 1, 1969

Heap leaching of copper sulphide and oxide ores' has been conducted at Rum Jungle since the end of 1965.A review of operations was made and this led to an examination of some theoretical aspects of copper sulphide heap leaching. Ox,ygen diffusion was indicated to be the factor controlling copper leaching rate at Rum Jungle and in other similar operations. Suggestions are made for measuring the heap leaching rate. Prediction of full scale operational results from pilot scale testwork are discussed.

Jan 1, 1969

By P. S. Katval

It is interesting to note that an attempt has been made to rationalize the effect of prestrain on the strength of Hastelloy X-280 after various aging treatments. However, two points raised by the authors seem to be somewhat unclear. 1) Concerning their Fig. l(a), the authors state: "Extensive dislocation networks are still in evidence. The 24-hr aging at 1500°F and the 15-min soak at 1350°F did not eliminate the dislocations introduced by the 20 pct cold reduction." This is, of course, to be expected since complete "elimination" of dislocations would require recrystallization which does not occur at 1500°F in Hastelloy X. However, recovery

Jan 1, 1969

By Kiyoshi Azuma, Hiroshi Kametani

The variation of the dissolution behavior of a ferric oxide with calcining temperature has been investigated. Samples were prepared by thermal decomposition of ferric hydroxide, nitrate, oxalate, and sulfate at low temperature, followed by the calcination in the temperature range between 600" and 1200°C. The samples of eight series and a fine crystalline sample of hematite were dissolved in 1 N hydrochloric acid at 55.2°C and the results are represented on double-log graphs for convenience. It is confirmed that all dissolution courses follouj either the accelerated process or the parabolic process except in the special case of the crystalline hematite which dissolced in accordance with the uniform dissolution of a particle. Examinations of the physical properties of the oxide powders revealed that the surface area measured by the permeability method is strikingly relevant to the dissolution behavior of the oxide. In the previous paper,' detailed data were presented on the effect of the kind of acid, the solution temperature, and the concentration of acid on the dissolution of two ferric oxides. It was also shown that these sam ples dissolved in strikingly different ways. The present investigation was carried out on the dissolution of various calcined samples prepared from various ferri salts by various methods to ascertain the course of dissolution. Pryor and Evans2 pointed out a change of the dissolution rate at around 700°C for a series of calcined ferric oxides prepared from the hydroxide. Several papers374 reported also the dissolution of ferric oxide samples. It seems, however, that a systematic account of the relationship between the dissolution behavior and physical properties of the oxide has not yet been given. This paper presents the variation of the dissolution of the oxide in relation to the calcining temperature and the change of physical properties of the calcines. EXPERIMENTAL Raw materials were prepared by precalcination of ferric hydroxide, thermal decomposition of ferric nitrate, oxalate, and sulfate, and aerial oxidation of ferric chloride vapor, at as low a temperature as possible. The products were crushed, ground, if necessary, and sieved with a 100-mesh Tylor screen prior to calcination, after which the specimens were dissolved in acid solution. The following is a detailed description of the preparation of the samples. Sample H. About 500 g of ferric chloride (guaranteed reagent) were dissolved in 5 liters of deionized water and filtered. Ferric hydroxide was precipitated by addition of the minimum amount of ammonium hydroxide solution, and the precipitate was washed continuously till chloride ion was not detected by silver nitrate solution, and then filtered. The filter cake was dried at 120°C for a week and ground, and the -100 mesh portion was used. Sample S. Ferric sulfate (guaranteed reagent) was pyrolytically decomposed in a crucible at 700°C for 24 hr and the product was sieved. In this case the following calcination was carried out at temperatures over 700°C. Sample B. Commercial ferric oxide (guaranteed reagent). About 15 kg of ferric nitrate were decomposed in a furnace maintained at 800°C for 2 hr. The actual temperature of the decomposition was not measured. The product was crushed and sieved, and the -100 mesh portion was used. Sample N. About 50 g of ferric nitrate (guaranteed reagent) were decomposed in a beaker in a sand bath until a red-brown dense solid was produced. This product was crushed and sieved, and subjected to complete decomposition at 500°C. The precalcined product was again sieved and used. Sample N2.5. Since the decomposition temperature was not controlled for sample AT, a different sample was prepared in a temperature-controlled furnace. The subscript represents the decomposition at 250°C. The product was treated in the same manner as sample N. Sample Nc. Under atmospheric pressure it is prac-tically inevitable that ferric nitrate hydrate melts to form a brown liquid at about 50°C before pyrolysis. For this reason, the salt was first slowly heated under reduced pressure (about 10-3 mm Hg measured in a trap refrigerated by dry ice-alcohol) to achieve dehydration without melting. About 5 hr were required for the dehydration and the partial decomposition. Then the temperature was elevated to 500° C in air for complete decomposition. The relatively porous product was sieved and used. Sample Ov. About 200 g of ferric oxalate hydrate (extra pure) were dehydrated under reduced pressure (as described above) followed by thermal decomposition at 500°C for 6 hr in air. The decomposition of this salt was accompanied by liberation of carbon monoxide, by which the ferric salt was initially reduced to a black powder. The powder changed in turn into brown ferric oxide as the gas liberation decreased and reoxidation predominated. The product consisted of sparkling fine particles passing through a 100-mesh screen. However it was ground and sieved as for the other samples. Sample D. Commercial fine powder for magnetic tape purposes. The preparation was as follows.5 Ferric chloride vapor and preheated excess air were mixed and passed into a reaction tube where oxidation took place at 450°C. The fine powder formed was collected in a cottrell chamber. The product was vacuum-degassed at 450°C for 1 hr and sieved.

Jan 1, 1969

By K. E. Gray, M. S. Seth

In Part I of this work,1 equations of elasticity were formulated for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure. Equations of elasticity and the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant rate of pressure or a constant rate of flow is maintained at the wellbore. In this paper, the approach presented earlier is extended to finite reservoirs for the cases of (1) steady-state flow, (2) constant pressures at the well bore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Results of this work show that radial and tangential stress gradients are high near the wellbore but diminish rapidt; away from the well; the vertical stress gradient behaves in the same way but is less severe. Radial stresses are compressive or neutral, whereas tangential and vertical stresses may be tensile, neutral or com-pressive, depending upon the boundary conditions, the physical Properties of the system and the radial distance involved (vertical stresses are always compressive in an unbounded system1. For constant boundary pressures, both radial and tangential stresses increase with time whereas they both decrease for a closed outer boundary and constant pressure at the wellbore. The vertical stress decreases with time for both systems. For steady-state systems, radial displacement may be positive or negative, depending upon the dimensions of the system, the pressure differential and the porosity. Radial displacement may be positive or negative for a closed outer boundary but is positive for constant pressures at both boundaries. INTRODUCTION The importance, utility and complexity of a realistic appraisal of the stress state at and local to a wellbore were indicated in Part I. In this paper the analytical approach presented earlier is extended to finite, cylindrical reservoir geometry for the cases of (1) steady-state flow, (2) constant pressures at wellbore and outer boundary and (3) constant pressure at the wellbore and no flow at the outer boundary. Other than the outer boundary of the reservoir being finite, the physical system and assumptions pertinent thereto are the same as before. The reader may wish to review the mathematical development through Eq. 49 of Part I before proceeding here. SOLUTION FOR GENERAL BOUNDARY CONDITIONS THERMAL STRESSES AND DISPLACEMENTS Since normal stresses do not exist at the free boundaries of a system subjected to thermal stresses, the boundary conditions are

Jan 1, 1969

By C. A. Komar

The Bureau of Mines conducted oil-displacement tests in the laboratory with three water-in-oil and five oil-in-water emulsions that were created with ultrasonic energy at a frequency of 20 kHz and an acoustic intensity of approximately 100 watts per cm2. Emulsions of either crude oil or kerosine, brine, and 112 to 2 percent emulsifier were formed during 30 seconds of acoustic irradiation. Results indicate that ultrasonic energy induces greater and more uniform dispersion of one liquid in another in the presence of small amounts of chemi¬cal emulsifiers. When the emulsions were injected as a buffer slug before waterflooding, recovery of the oil-in-place was 8 to 22 percent greater than with conventional waterflooding in the test specimens, regardless of the con¬tinuous phase (oil or brine). The emulsions do not appear to be applicable to the Appalachian area; however, because the oilfields are too "tight," the clays in the formation remove the emulsifier from the displacing fluid, and not enough additional oil is produced, compared with recovery using conventional waterflooding, to warrant the increased operating costs.

Jan 1, 1969

By Edward J. Karkoska

The film you see is a slow motion view of a typical half million ton taconite blast at one of Erie's mines. This blast is made up of 220 drill holes and a total of 325 thousand pounds of blasting agent. The second view of the same shot is taken by a remote control hi speed camera located 1500' directly in front of the blast. Shortly you will see some violent camera movement as the air blast shock wave strikes the camera location. As the blasting sequence progresses the rock fly becomes evident, and if you will look closely amidst the clouds of smoke, rock fragments weighing up to 1/2 ton begin to cascade into view. These missles are the chief concern of blast security. The next camera shot at 4000 frames/second vividly describes the primacord firing lines detonating the blast. Travelling at 22,000 ft./sec., this white snake of fire travels to each hole, detonating the blasting agent. Before we get into the matter of blast security, let me locate our operation for those of you not acquainted with Minnesota's iron ranges and tell you something about our company.

Jan 1, 1969

By R. E. Reed-Hill, W. H. Hartt, W. A. Slippy

An unusual form of double kinking has been observed at the ends of {1121} twins in deformed zirconium. These kinks lie partly outside of the twin and partly inside. While they are undoubtedly closely associated with accommodating the twinning shear into the matrix, they are apparently closely related to other important aspects of twin growth. A mechanism is proposed for {1121} twin growth involving interactions between 1/3 (1120) dislocations in the bend planes and twinning dislocations. It is also shown that boundaries without long range strain fields develop at the tapered ends of the twins. The {1121} twins can, therefore, grow without forming high-energy noncoherent twin boundaries containing large numbers of closely spaced twinning dislocations. NUMEROUS investigators have indicated that slip is often closely associated with deformation twinning. An example is twin accommodation kinking,1-3 where dislocations form bend planes and permit accommodation of a twinning shear within the parent crystal. Another is the incorporation of slip dislocations into twins, as proposed by Sleeswyk and verbraak4 and Ishii and Kiho5 for iron and ß-tin, respectively, and observed in hcp metals by Price.6 In addition, it has been shown that shear discontinuities exist at the points of twin intersections in zinc,7 magnesium,8 titanium,9 ß-tin,10 and bismuth," where the continuity conditions for twin intersections, originally proposed by cahn,12 are not satisfied. A similar situation occurs for zig-zag (1121) twins in zirconium13 and ?-phase silver-aluminum alloys,14 where the twinning shears of the two component twins are not parallel. In all these latter cases additional deformation by slip is believed to accommodate the twinning shear discontinuity. The present paper is concerned with a newly observed aspect of the slip and twinning interrelation, in which two kinks, one inside the twin and the other external to the twin, are formed. These kinks, observed in conjunction with (1121) twinning in zirconium, form to accommodate the twinning shear. A model has been constructed explaining the growth and accommodation of (1121) twins in terms of these kinks. This mechanism may be significant since it is concerned with an important twin mode, which occurs not only in zirconium but also in titanium and hafnium. The practical significance of (1121) twinning has been adequately demonstrated. At 77° K the high ductility of zirconium containing a large number of grains unfavorably oriented for slip is primarily due to (1121) twinning.'5 Also, (1121) twins nucleated at 77°K may grow during further deformation at room temperature. This growth can greatly increase the transverse ductility15 as well as produce large mechanical hysteresis effects.= EXPERIMENTAL PROCEDURE Arc-melted, sponge zirconium plate previously described17 was prestrained 0.65 pct at 77° K by cold-rolling to introduce {1121} twins into the structure. Tensile specimens were cut with axes normal to the plate rolling direction. These specimens were pulled in tension to near the point of failure in an Instron machine at room temperature at a cross-head speed of 2 x10-2 in. per min. This additional deformation caused growth of the twins nucleated by prestrain. Deformed specimens were then prepared for metallo-graphic examination. This included an anodizing treatment18 that made the surfaces sensitive to polarized light, permitting small lattice rotations to be revealed. EXPERIMENTAL RESULTS Nature of the Twin-Kink Band Structure. Fig. 1 is a photomicrograph of a typical specimen after prestrain at 77° K. The structure is characterized primarily by long, narrow, parallel sided (1121) twins which norma1ly traverse the entire grain. Fig. 2 shows several (1121) twins after additional straining at room temperature. These lie near the center of the polarized light photomicrograph and are inclined upward to the right. It is evident that this latter deformation has resulted in appreciable twin growth. The dark regions extending from the ends of these twins are accommodation kinks. The difference in reflected light intensity indicates the

Jan 1, 1969

By P. Bolsaitis, L. Skolnick

Vapor pressures of silver over ternary alloys of six different copper to gold ratios have been measured by means of the Knudsen effusion technique. The data obtained in the temperature range of 1330° to 1375° have been used to estimate the integral excess free energies of the ternary alloys and the activities of copper and gold. The results compare favorably to the predictions based on the electron cell model of alloys recently formulated by the authors. THE orifice effusion method for measuring vapor pressures of materials in condensed phases was first introduced by knudsen, and has since been used extensively for the determination of thermodynamic properties of condensed phases. The basis of the measurement is the effusion, through a small orifice, of vapor in equilibrium with a condensed phase. Assuming free molecular flow into high vacuum, the vapor pressure, P (in mm Hg), of the effusing species is calculated from the following equation:' where w (g) is the weight of effusing species lost during a run, t (sec) the time length of the run, A, (sq cm) the area of the effusion orifice, T ("K) the temperature at which the run is conducted, M the molecular weight of the effusing species, and k the Clausing factor, a constant that corrects for deviations from free molecular flow caused by the finite thickness of the orifice walls.17 The determination of partial and integral thermodynamic variables from vapor pressure data of ternary alloys is possible only if the vapor pressures of all but one component are negligible or can be esti-

Jan 1, 1969

By E. H. Erwin Gartner

The Rhenish lignite deposit in the Nordrhein-Westphalia province of the German Federal Republic covers an area on the left bank of the Rhine River of about 970 sq miles (Fig. 1). Here, in the Miocene era, some 20 million years ago a lignite seam was formed and later broken, through tectonic movements into several blocks, some thrown down into depths of over 1,500 ft. This deposit consists of a single seam, in places up to 300 ft thick, but averaging about 150 ft. In a few areas, it is split into as many as five seams, separated by barren strata. It contains about 60 billion tons (2000 lb/short ton) of lignite which, however, being relatively young geologically, has, because of approximately 60% moisture, 2 to 8% ash, and low sulfur, a net calorific value of 3,340 Btu. That calorific value increases, however, with rising thickness of the cap rock. About one-third of the yearly production of 90 to 100 million tons of raw lignites is converted into briquets. Raw lignite is pulverized and dried to about 18% water content and then pressed without binder into briquets under a pressure of about 14,000 psi. The briquets are being used primarily for residential heating; their sales, however, have been declining sharply since 1963. On the other hand, the volume of raw lignite used in steam power plants has been rising steadily and amounts at present (1968) to about two-thirds of the total production. Huge steam power plants, such as Frimmersdorf, shown in Fig. 2 (which, with an installed capacity of 2,600 MW [megawatt], represents the world's largest steam power plant) with a generating capacity of up to 300 MW per unit and a total installed capacity of over 6,000 MW, contribute about 26% of the total electric power production of the German Federal Republic.

Jan 1, 1969

By W. N. Hamilton

As a result of a test-drilling program conducted by the Research Council of Alberta in 1968, a gypsum deposit averaging 30 feet in thickness, with a chemical purity of 84 per cent gypsum, has been proven to underlie the Clearwater River valley for a distance of 18 miles at depths ranging from near-surface to 300 feet. This and other subsurface deposits in the vicinity of Fort McMurray, Alberta are the product of local hydration of anhydrite beds believed to be the water-insoluble remains of the leached Prairie Evaporite formation of Middle Devonian age, the thick salt section of which is preserved down dip. The effects of salt solution are seen in the disturbed bedding and the intermixture of greyish green shale with gypsum in the core, the shale content being responsible for the rather low chemical purity of the deposit. A similar gypsum deposit, but probably of higher purity, is postulated to occur beneath the Athabasca River valley about 60 miles north of Fort McMurray.

Jan 1, 1969

By Brian W. Mackenzie

The mine development decision is made on completion of exploration to determine whether or not a mineral deposit should be developed to production and, if so, how. This involves the selection of an optimum mine development alternative from a number of technically feasible alternatives and the comparison of this optimum with those of other available investment opportunities. If the optimum is sufficiently attractive, the deposit is developed to production. The selection process is carried out within a framework of corporate objectives and resources. The mine development decision is based on the balancing of two parameters - - rate of production as reflected in plant capacity and cut-off grade. On the basis of available information and experience, detailed revenue and cost 'estimates are made for each feasible combination of plant capacity and cut-off grade. What economic evaluation techniques should be applied to these estimates to reduce each alternative to economic indicators that will enable meaningful comparisons and an informed investment decision? This is the essence of the paper. The determination of optimum plant capacity and cut-off grade has been the subject of intensive research efforts by economists and mining engineers (1-7). Their studies are based on marginal analysis and assume that, at the time of decision, certainty conditions prevail with respect to ore reserves, mining costs and mineral markets. The optimum mine development alternative is defined as that which maximizes profitability.

Jan 1, 1969

By David W. Wisecarver

The U.S. Bureau of Mines, in cooperation with U.S. Borax and Chemical Corporation and the Kennecott Copper Corporation, has investigated the use of the microseismic method to evaluate the stability of large, open-pit slope walls. The method is based on the phenomenon that stressed rock normally emits subaudible rock noises, and the number of rock noises per unit time (noise rate) and the magnitude of the rock noises (amplitude) increase as the stresses in the rock approach the failure stress of the rock. Therefore, the detection and recording of those rock noises serve as a semiquantitative method of predicting the incipient failure of rock. This report briefly describes the three different types of microseismic apparatus, the procedures, and the results of microseismic investigations in the slope walls of the Boron Mine near Boron, California, and the Rimbley, Liberty, and Tripp-Veteran open-pit mines near Ely, Nevada. Microsesimic noise rates in stable inactive mining areas are between 0 and 10 noises/ hour; the rates in stable active mining areas are between 10 and 50 noises/hour; and the rate in unstable areas is as high as 2500 noises/ hour. High microseismic noise rates in the Liberty Pit correlate with the time of nearby earthquakes, indicating that the earthquakes affected the slope wall. The results provide evidence that the microseismic tech¬nique is applicable to large pit walls, and that the wide band, wide range microseismic equipment appears to be suitable for open-pit investigations.

Jan 1, 1969

By B. Chalmers, Stefan Wojciechowski

Rotary oscillation of the mold has been used to produce mechanical stirring of the melt during unidirectional solidification. Al-Cu alloys (1 to 4 wt pct Cu) were solidified to study the influence of alloy composition, temperature at which intensive cooling was initiated, and intensity of stirring on the temperature distribution in the sample, the resulting structure, and the copper microsegregation at the columnar to equiaxed transition. The Proposed explanation for the equiaxed solidification in stirred castings consists of the melting off of dendrite fragments, their partial remelting in hotter liquid, and the subsequent growth of the surviving part when the temperature of the melt is lowered. This may result in the formation of a crystal network, which can stop the growth of the columnar crystals and produce the equiaxed zone. It has long been known and many times affirmed that ultrasonic vibrations or relative motion of liquid and solid can significantly reduce the length of the columnar zone and refine the grains in the equiaxed zone in ingots and castings. Because of the technological importance of these phenomena many investigations have been conducted in which ultrasonic energy or mechanical vibration,1-6 electromagnetic stirring,7"10'17 magnetic stirring,"'12 or mechanical stirring13'14 were used to produce the relative liquid-solid motion. More recently, the question of the importance of natural (or thermal) convection has been raised.15-l7 Several possible mechanisms have been suggested.l,8,18-20 They can be divided into two main groups. The first group includes such nucleation hypotheses as nucleation frequency enhancement due to cavitation at the mold wall or other surfaces; cavita-tion in the body of the liquid resulting from the pressure wave, or an agglomeration mechanism, which involves the formation of nuclei by the accretion of subcritical nuclei. The second group considers the grain-refining action to be due to crystal multiplication phenomena such as the removal of the dendrite fragments by viscous forces or by a high-pressure cycle following cavitation or by a melting-off process. Sbme recent investigations give good experimental support to the melting-off proposa1.21-23 The purpose of the present study was to examine the effect of mechanical stirring during the unidirectional solidification on the structure of alloy samples and on the solidification variables. The motion of the liquid was produced by rotary oscillation of the mold around its vertical axis.

Jan 1, 1969

By K. D. Genn, A. Mucha

This paper deals with Hilton Mines' approach to the maintenance of wear items such as truck boxes, shovel buckets, tractor pads, crawler sprocket idlers and the drop-ball. Each will be given a brief. description as to application, design, kind of materials involved and type of wear. The maintenance procedure is then outlined in terms of materials used, preliminary preparation, and welding and machining practices. The service history of new and re-paired items and the relative economics of repair vs replacement will then be presented.

Jan 1, 1969