Search Documents

By Peter Swanson

One of the primary methods for analyzing roof stability in underground mines is the age-old method of “roof sounding” where a miner taps on the roof and listens for the hollow sound of loose blocks of rock. This paper looks at the feasibility of using noncontact laser-based vibration measurements to detect roof fall hazards with the ultimate vision of improving, expanding and automating procedures for mine roof inspection. Vibration measurements made on loose blocks of rock in underground mines are summarized and compared to estimates of fundamental resonance frequencies for rock slabs of the size responsible for highly hazardous “skin failures.” Both laser Doppler vibrometry and full-field interferometric methods are examined and are considered to be feasible methods for detecting anomalous vibrations in loose roof rocks. Results from simple laboratory experiments using laser vibrometry demonstrate some of the proposed application concepts. While considered a challenge to move these techniques from the laboratory to heavy industrial or outdoor environments, the potential for success in the current application is enhanced by the reduced requirements of qualitative analyses.

By T. L. Loucks, E. T. Guerrero

Pressure drop characteristics in a system composed of two adjacent concentric regions of different permeability were studied. The differential equations for continuity of mass flow in the two regions were solved using the Laplace transformation and the necessary boundary conditions to give the pressure distribution in the composite reservoir, the resulting equation for pressure drop at the inner boundary was evaluated for a variety of composite reservoirs and compared with the results for a uniform reservoir. From this study it was found that under certain conditions the permeability in both zones, as well as the size of the inner zone, can be determined from the pressure drop curve. INTRODUCTION The theory for the pressure distribution and pressure build-up behavior of a well producing a single, slightly compressible fluid from infinite and finite homogeneous reservoirs was presented by Hornerl and Miller, Dyes and Hutchinson.2 Extensions on this original work to provide improved and extended interpretations and better agreement between theory and observed results have been made by Matthews, et a1,3 van Everdingen,4 Gladfelter, et al5 Stegemeierand Matthews,6 Hurst and Guerrero,7 and Perrine.8 More recently Lefkovits, et al,9 studied pressure build-up behavior in bounded reservoirs composed of stratified layers. Houpeurtl0 has suggested various approaches to the general problem of variable permeability and porosity but presented no analytic solutions for particular permeability variations. Albert, Jaisson and Marionll studied the finite composite reservoir and presented numerical solutions to the unsteady-state case and an analytical solution valid only for large times. They also studied the so-called pseudo-steady state for several examples of radial permeability variations. Very similar examples have been treated in the unsteady state with application to pressure build-up by Loucks in an unpublished manuscript. More recently Hurst12 has presented the complete point-sink solution (valid for all times) for the infinite composite reservoir. He applied these solutions to interference between oil fields along with an even more elegant application of his explicit solution to the material-balance equation including water influx. Mortada 13 approaches the same application by avoiding the point-source limitation but gives the solution for the aquifer region which is valid only for large times. Hopkinson, Natanson and Temple14 have treated both the finite and infinite composite reservoir obtaining the pressure distribution for the inner zone valid for large times. This paper presents a theoretical study of the pressure distribution in an infinite composite reservoir composed of two adjacent concentric regions of different permeability. The object was to determine the manner in which pressure drop at the inner boundary of a composite reservoir depends upon time, the permeability of each zone and the size of the inner zone. Expressions for the pressure distribution in both zones are developed which take into account the radius of the sink and are valid for small times as well as large times. It was felt that an understanding of the pressure drop behavior in various composite reservoirs would be of assistance in the interpretation of some pressure build-up curves which do not behave according to the theory derived for uniform systems. Often the region surrounding the wellbore is either more permeable or less permeable than the reservoir because of the various drilling and completion practices. The effects of reduced permeability due to drilling-fluid invasion and of increased permeability due to fracturing or acidizing need to be more carefully defined. Therefore, an equation for the pressure drop in a composite reservoir was developed, and the effects of both the permeability in each zone and the size of the inner zone were studied. STATEMENT AND SOLUTION OF PROBLEM BOUNDARY CONDITIONS AND ASSUMPTIONS The physical system studied was a composite

In choosing such a threadbare subject for a paper I fear that I may in some measure be taxing your patience, yet as upon the accuracy with which the work is done depends the result of conclusions drawn as to whether a property will be profitable to work or otherwise. The subject cannot be too well threshed out, and I trust that upon certain points that have come within my own experience I may be able to give 'hints that will prevent others from making mistakes. First as to alluvial. Gold is often found from the grass roots down, often ill particular horizontal bands in the wash, but more generally concentrated either on a true or false bottom. When sampling dry ground for proposed hydraulicing I have obtained accurate results only by taking the whole of the dirt from measured shafts, stacking it as it was lifted on a tarpaulin, and putting the whole quantity through a carefully constructed box. In wet ground careful borings will in most cases give fairly correct results, but where it is possible to sink shafts, that should be done, as a guide is then also obtained as to the nature of the wash, whether it is bouldery, cemented, or free. Sampling in a face is a more difficult work in many respects than in new ground, as so many elements enter into action to spoil accurate sampling. Of course the great thing to avoid is sampling in any place where either natural or artificial concentration has taken place, and very much has to be left to circumstance and the sampler's own judgment. In passing I may mention that I have on several occasions seen diggers deceive themselves in wet ground where they were sinking and coping as best they might with water. They would take a dish of dirt from the bottom of their hole, pan it off, and take the result as a fair yield, and on the strength of it perhaps spend a lot of time and money in tail races and whereas in their sample there had been a process of concentration carried on, the movement and working in the water had caused the gold to work down, and anything like accurate estimations by the method pursued were out of the question.

By M. J. Senk, A. Lusin

Federal regulations require that methane liberated at the face be diluted and removed to maintain methane gas concentrations below 1 pct (CFR) in working places and intake air courses. The delivery and distribution of intake air at the face is critical for effective face ventilation. Improved techniques for monitoring the movement of intake air to the face are needed. A test system was developed and a computer program written for using a three-axis ultrasonic anemometer to measure airflow in a simulated mine entry. Results of tests conducted in the entry showed that the anemometer is a valuable tool for measuring mine airflow conditions near the face.

By Edward D. Thimons, Jay F. Colinet

NIOSH conducted a strategic planning effort to identify those areas in mining with the greatest research needs. Data analysis and stakeholder input identified the need to reduce worker exposure to respirable crystalline silica dust as a high priority area. MSHA dust sampling data were analyzed to target the mining commodities and occupations with the greatest percentage of samples containing silica above compliance levels. In response, the Pittsburgh Research Laboratory (PRL) has implemented a multi-faceted research program to improve silica dust control for these problematic commodities and occupations. A review of silica compliance trends, PRL silica research programs, and recent control technology developments are provided here.

By M. G. Corson

Information regarding the use of ixanganese alloys has hitherto been incomplete and available only from widely scattered sources. This paper attempts a systematic description of properties and uses of alloys other than manganese bronze, manganin and duralumin, which are probably the only non-ferrous alloys associated with manganese in the minds of most metallurgists. Properties of Manganese Manganese can react either acid or basic; it is hard to obtain in the pure state; it has two different crystalline lattice structures, both of the cubic system, one stable above 850" C. and the other below 650" C., both coexisting in the intermediate range. Although the commercial product is hard and brittle, the pure metal seems to be ductile. In fact Zhemchuzhny, in Russia, was able to obtain ductile manganese and draw it to fine wires by the simple expedient of adding about 3 per cent. copper to the alumino-thermic product. Copper most probably brings the sili-cides, aluminides, nitrides and carbides present in the commercial product into a much less harmful form of distribution. One industrial use that can be foreseen for wrought manganese articles is as anodes for electrolytic processes in sulfate and nitrate solutions, particularly with high voltages. A practically insoluble skin of manganese peroxide is likely to form in such cases and an insoluble and strong anode material will be available. Manganese as a Scavengek Because of its activity manganese might become the most efficient scavenger and refiner of copper, were it not for the fact that 0.01 per cent.

By P. Majani, F. P. Kokesh, M. Grosmangin

Determination of the quality of cementation of casing in oil wells in the past has involved inflow and circulation tests to insure that the producing zones were adequately sealed off from the adjacent zones. Existing logging methods, such as temperature and radioactivity surveys, may detect the presence of cement behind the casing. However, the qualities of the cement (i.e., its hardness and particularly its bond to the casing) are not indicated. The new logging method described in this paper operates on the principle that the attenuation of a sonic pulse transmitted by a casing is greatly increased when that casing is bonded to an outer annulus of hard material (such as set cement) which has an appreciably smaller sonic-wave velocity than that of the casing. The down-hole tool contains a source of recurrent sound pulses which are detected by a receiver spaced a few feet from the source The amplitude of the detected casing-borne pulse is measured, and the resulting signal is transmitted to the surface where it is recorded vs depth. Since amplitude is a function of attenuation, the log is readily interpreted. Laboratory studies have shown straightforward relationship between attenuation and such variables as source-detector spacing and per cent of circumference bonded. It is shown that cement not set or not bonded to the casing has compara- tively little attenuating effect. Field examples show not only the cement top, but also the variation in cementation quality below the top. Further, the increase of bonding with time and after squeeze cementation is depicted. The detection of poor cement jobs is confirmed by production tests and by formation-test results. It is anticipated that the method will have wide application in evaluating cementation quality prior to formation testing in completions and recompletions. The analysis it affords may aid in further improving cementation techniques. INTRODUCTION The main purpose of oilwell cementing is to isolate a production zone from other undesirable zones. To investigate whether this purpose has been accomplished, several logging methods have been used such as temperature logs, radioactive tracer logs, etc. While these logs all respond to the presence of cement behind the casing, they do not indicate the degree of bonding of the cement to the casing. Early in the application of sonic logging, it was noticed that considerable attenuation of sound signals takes place in cemented pipe and is often made evident on the standard Sonic log by cycle skipping.' The development of a circuit capable of continuously recording the amplitude of the casing-borne sound signal has made possible an extensive series of laboratory and field tests, which gave the following results. The amplitude of a sound signal after it has traveled in a firmly cemented pipe is only a small fraction of that recorded by the same device in free pipe. This provides a wide spectrum of energy levels; for given local conditions, empirical values of the amplitude can be correlated with the quality of cementation. Interpretations made in this manner generally have been confirmed by production tests, circulation tests and squeeze cementation. The purposes of this paper are to give a general description of the new logging method and to present some laboratory and field results. CYCLE SKIPPING Early attempts to study the quality of the cement behind the casing were performed with a standard Sonic log, which measures the transit time At, and were based on the well known phenomenon of cycle skipping.' Cycle skipping normally is interpreted as being a manifestation of weak signals at the receivers. The log of Fig. 1 was run with the recording instrumentation adjusted to enhance cycle skipping. A mirror-image presentation was used for better visual interpretation. The transit time of sound in steel is about 58 microseconds/ft (corresponding to a velocity of 17,000 ft/ sec), and the portions of the log where this value is recorded are interpreted as zones with no cement bond. Where cycle skipping produces a higher value of At, weak signals (or a high rate of attenuation) are indicated, and a good cement bond may be present. The occurrence of cycle skipping, however, depends too much on instrument adjustment to give a uni-

By B. E. Eakin, R. T. Ellington

An apparatus and a procedure for determining the viscosity behavior of hydrocarbons at pressures up to 10,000 psia and temperatures between 77 and 400° F are described. The equipment is suitable for measuring viscosity of either the liquid or vapor phases or the fluid above the two-phase envelope for systems exhihiting retrograde phenomena, according no the phase state of the system within these ranges of temperature and pressure. Equations are developed for calculation of viscosity from the experimental measurements, and new data for the viscosities of ethane and propane at 77° F are reported. INTRODUCTION With the advent of higher pressures and temperatures in industrial processes and deep petroleum and natural gas reservoirs, demand has increased for accurate values of physical properties of hydrocarbons under these conditions. Proportionately, more frequent occurrence of natural gas and condensate-type fluids is encountered as fluid hydrocarbons are discovered at greater depths. This increases the importance, to the reservoir engineer, of being able to predict accurately the physical properties of light hydrocarbon systems in the dense-gas and light-liquid phase states. Reliable gas viscosity data are limited primarily to measurements made on pure components near ambient temperature and at low pressures. Few investigations have been reported for high pressures, and except for methane, data on light hydrocarbons are subject to question. This is demonstrated by the large discrepancy between sets of data on the same component reported by different investigators. For mixtures in the dense gas and light liquid regions and for fluids exhibiting retrograde behavior there are very few published experimental data. Viscosity data for methane have been reported by Bicher and Katz,1 Sage and Lacey,12 Comings, et al,3 Golubev,3 and Carr,3 with good agreement among the last three sets of data. Comings, Golubev and Carr utilized capillary tube instruments for which the theory of fluid flow is well established. The theory permits calculation of the viscosity directly from the experi- mental data and dimensions of the instrument alone. Sage and Lacey, and Bicher and Katz used rolling-ball viscometers. The theory of the rolling-ball viscometer has not been completely established, and these instruments presently require calibration by use of fluids of known viscosity behavior before viscosities of test fluids can be measured. To obtain accurate data it is necessary that the rolling-ball viscometers be calibrated by use of fluids of density and viscosity similar to the test fluids, a difficult selection for the gas phase. From the methane data and experimental tests on various natural gases, Carr developed a correlation for predicting the PVT behavior of light natural gases.2,3,4 This correlation was based on data for a very limited composition range; its application to rich gases and condensate fluids is questionable. The object of this investigation is to develop an instrument which can be used to obtain viscosity data at reservoir temperatures and pressures, for rich gases, condensate-type systems above the two-phase envelope and light liquid mixtures. These data will be used in an effort to develop correlations to represent the viscosity behavior of these fluids. APPARATUS In a previous viscosity study Carr2 utilized a modified Rankine capillary viscometer configuration," Fig. 1. In this instrument the gas to be tested is forced through the capillary tube in laminar flow by motion of a mercury pellet in the fall tube, the measured displacement time being that required for the mercury slug to move between the brass timer rings. The viscometer is constructed of glass and mounted in a steel pressure vessel. The test gas pressure in the viscometer is balanced by an inert gas (usually nitrogen) in the vessel. Excellent results have been obtained with instruments of this type, with Carr2 and Comings5 reporting repro-ducibilities of 99.5 to 99.3 per cent and an estimated absolute accuracy of 99 per cent. However, these instruments have limitations which have precluded their use for liquids. The need for maintaining a balance between pressures of the test fluid and inert gas in the viscometer vessel presents operating problems, and requires charging the test fluid to the viscometer very slowly. The principle drawback to the Rankine unit is behavior of the mercury slug which provides the pressure differential across the capillary. When even trace quantities of propane or heavier hydrocarbons are present in the test gas, the mercury tends to subdivide

By L. W. Holm

Laboratory flooding experiments on linear flow systerns indicated that high oil displacement, approaching that obtained from completely miscible solvents, can be attained by injecting a small slug of carbon dioxide into a reservoir and driving it with plain or carbonated water. Data are presented in this paper which show the results of laboratory work designed to evaluate this oil recovery process, particularly at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi. Under these conditions CO2 exists as a dense single-phase fluid. It was found that a bank, rich in light hydrocarbons, was formed at the leading edge of the CO? slug during floods on long cores. Formation of this bank is probably due to a selective extraction by the C02 and, it is believed, partially accounts for the attractively high oil recoveries. In crddition to the efficient displacernerlt of oil from the pores of the rock by this process, the favorable rnobility ratio related to a C0 2-water flood also contributes to high oil recovery. A further advantage of this process is noted on limestone and dolomite rock, in that the CO1 reacts with the porous medium increasing its permeability. Flooding experiments were conducted on sandstone and vugular dolomite models. The results of this experimental work show the effect on oil recovery of type of porous medium, pore geometry, flooding length, and flooding pressure. The porosity of the cores and rilodels varied from 16 to 21 per cent and their pern~eabilities ranged from 100 to 200 md. A reconstituted West Texas reservoir oil, a West Texas stock tank oil, an East Texas stock tank oil and Soltrol were used to represent reservoir oils in this study. Oil recoveries ranging from 60 to 80 per cent of the original oil in place in these cores were obtained by CO2,-carbonated water floods at pressures between 900 and 1,800 psi, compared with conventional solution gas drive and water-flood recoveries of 30 to 45 per cent on the same cores. Oil recoveries greater than 80 per cent resulted frorn f1oods at pressures above about 1.800 psi. There high recoveries were noted from both the sandstone and the irregular Porosity carbonate cores. In all floods, additional oil was recovered by a solutiorr gas drive resulting from blowdown following the flood. Oil recoveries of 6 to 15 per cent of the original oil in place were obtained during this blowdown period. This additional recovery was found to be a function of oil remaining after the flood, decreasing with decreasing oil saturation. It was also noted that highest oil recoveries by blowdown were obtained when carborlated water rather than plain water followed the CO, slug. INTRODUCTION Miscible phase or solvent flooding processes, which are designed to increase oil recovery -from petroleum reservoirs, involve the injection of small quantities of a petroleum solvent into the reservoir, followed by an inexpensive scavenging fluid which is miscible with the solvent. Essentially complete displacement of oil from the pores of reservoir rock has been obtained by this technique. CO,, although not completely miscible with most reservoir oils at moderate pressures, is highly soluble in these oils at pressures above about 700 psi; there is appreciable swelling and reduction in the viscosity of oil when CO, is dissolved in it. Therefore, CO, could be expected to perform similarly to other oil solvents as a displacing agent. CO, is also highly soluble in water at elevated pressures, so water should be a satisfactory material to drive a slug of CO, through an oil-bearing reservoir. A favorable mobility ratio would be obtained through the reduction in viscosity of the oil and the use of water as a final displacing agent. A number of investigations of the use of CO, to improve oil recovery have been reported in the literature.2,3,4,5,6 These studies, however, have been conducted on uniform porosity sandstone at relatively low temperatures and pressures. The behavior of CO1 as a flooding agent at temperatures above its critical temperature could not be predicted adequately from these studies, particularly for the case of non-homogeneous rock. The purpose of this work was to evaluate the oil recovery efficiency of a process involving the injection of a CO2 slug followed by carbonated water, at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi, and to compare this process with conventional water flooding. The investigations were primarily designed to provide information on the efficiency of the process in irregular porosity carbonate rock. The effects of flooding path length, the presence of free gas, the type of oil to be recovered, and the amount of solvent required were also determined. The essential results of static phase behavior studies and experimen-

By B. Anamaeric

Economic, environmental and operational disadvantages of the traditional blast furnace process has led to the development of direct smelting reduction processes, including those that utilize self reducing/ fluxing dried greenballs as iron oxide feed materials. This is mainly due to improved carbothermic reduction, carburization and reaction kinetics. In this paper, the morphological changes of the greenballs as they transform to pig iron nuggets are examined over time at a constant temperature of 1,400° C. The products produced after each treatment were characterized using optical microscopy, scanning electron microscopy/energy dispersive spectroscopy and point counting/image analysis. The changes in the percent metallized area, wustite dendrite and slag matrix content of the structures were calculated. It was determined that the transformations were initially controlled by dissolving and containment of iron oxides in the molten slag and their consequent reduction to iron, followed by coalescence of the metallized areas. The final transformations were controlled by the carburization of the metallized areas.

On Dec. 20, 2013, an 8-m (26.2-ft) diameter Robbins hybrid single shield/earth pressure balance tunnel boring machine (EPB TBM) was launched to bore the Grosvenor decline tunnel for Australia?s Anglo American coal mine. The machine was built using onsite first time assembly (OFTA) in order to fit within a tight project schedule. Assembly at the remote jobsite near Moranbah, Australia took about four-and-a-half months, and then the machine was walked down into a launch tunnel. Two decline tunnels, at grades of 1:6 and 1:8, will be used for mine access to new coal seams. The hybrid machine is tackling mixed ground conditions ranging from sand and clay to varying types of sedimentary hard rock up to 120 MPa UCS, as well as coal seams. Methane gas is expected to be present throughout the tunnel, so the machine has been designed as explosion-proof-compliant to ERZ-1. ?Grosvenor is the first underground coal mine in Queensland to use a TBM for drift construction,? said Glenn Tonkin, Grosvenor project director. ?We are proud to be pioneering this technology.? Only about 300 m (984 ft) of ground in each decline tunnel is expected to require EPB mode, while the rest of the tunnel will be bored in hard rock mode. Thus, the design was optimized toward hard rock excavation.

The ability to track miners and communicate with them while they work in underground coal mines is important during normal daily operation, and critical in emergency conditions. This was evident during recent incidents at underground coal mines worldwide. Communication with miners and the knowledge of their location is of great importance for rescue efforts and the preservation of life. Numerous technologies have been developed, adapted and deployed to meet tracking requirements of the Mine Improvement and New Emergency Response (MINER) Act of 2006. Evaluating the performance of these systems has proven to be dif?cult for mine operators, system manufacturers and regulatory agencies. The MINER Act requires operators to improve accident preparedness by developing an emergency response plan speci?c to each mine. With the recent implementation of the provisions of the MINER Act of 2006, all underground coal mines in the United States are subject to the mandates of legislation concerning communication and tracking system installation. As of June 2011, 203 new or revised tracking and/or communication systems had been approved by the U.S. Mine Safety and Health Administration (MSHA), with nearly 50 other systems or revisions in the approval process (MSHA, 2011). At that time, the available approved systems for underground coal mine use included these types: ? Leaky feeder communication systems. ? Fixed node-based communications and/or tracking systems. ? Wireless node-based communications and/or tracking systems. ? Medium frequency (MF) communication systems. ? Communication system peripherals. Other types of tracking systems have since been developed and some manufacturers are seeking approval for use in this application. Some of the new products include through-the-earth (TTE) systems and various radio frequency (RF) adaptations. New technologies that are currently being developed and deployed in other industrial applications should also be considered, including acoustical, optical, inertial and hybrid technologies. To date, no uniform method has been employed in the industry to effectively compare and evaluate the performance of installed systems. Neither industry operators nor regulatory agencies can accurately assess the capabilities of installed systems in the continuously changing mine environment. There is a need for a uniform evaluation method that provides the ability to assess how different systems and technologies perform in various mining applications, and whether they can satisfy the regulatory requirements.

By R. Sellaro

It has long been understood that extended occupational exposures to respirable mine dusts can lead to chronic lung disease. In underground coal mines, coal workers pneumoconiosis (CWP) and silicosis are major concerns. While there have been many studies aimed at understanding total dust concentrations and silica content associated with different mining conditions (e.g., locations/occupations within a mine, cutting methods, geologic strata), little research has been completed to more comprehensively characterize respirable dust (i.e., by distributions of particle composition, size or shape). For such analysis, scanning electron microscopy with energy dispersive X-ray (SEM-EDX) may represent a powerful tool. This article is a preliminary investigation of SEM-EDX to characterize respirable dust from an underground coal mine in Central Appalachia. Samples were collected from various locations in the study mine, and individual dust particles were identified and classified by mineral type. A continuous personal dust monitor was also used to estimate respirable dust concentrations during sampling. This data was compared to particle densities observed under the SEM. Dust is generally defined as small, solid particles with an effective diameter between 1 and 100 µm. In underground coal mines, dust is produced by a variety of activities such as coal and rock cutting, materials handling, haulage and from a variety of materials. While the coal itself is primarily made up of organic carbon, it is estimated that as much as 60 percent of coal mine dust consists of mineral matter, including clays, metal oxides and sulfides, carbonates, quartz, phosphates and heavy minerals (WHO, 1997). Mineral matter may be ingrained in the coal seam or associated with adjacent or interlying strata, and may also be contributed by specific activities such as rock dusting. When dust is generated or made airborne, suspended particles tend to settle slowly with gravitational forces, but can remain airborne for extended periods of time depending on environmental conditions such as air velocity (Courtney et al., 1986) and particle properties such as size (ISO, 1995; WHO, 1999). Thus, miners working underground are routinely subject to occupational dust exposures ? with highly variable characteristics between and even within mines.

By N NA

By Sean Gallagher, William S. Marras, Alan S. Litsky, Deborah Burr

Background. There is currently little information regarding factors associated with specific modes of motion segment failure using a fatigue failure model. Methods. Thirty-six human lumbar motion segments were fatigue tested using spinal compressive and shear loads that simulated lifting a 9 kg weight in three torso flexion angles (0, 22.5, and 45). Twenty-five segments failed via fatigue prior to the 10,000 cycle maximum. These specimens were visually inspected and dissected so that the mode(s) of failure could be determined.Failure modes included endplate fractures (classified into nine varieties), vertebral body fractures, and/or zygapophysial joint disruption. Logistic regression analyses were performed to determine whether certain morphometric variables, amount of motion segment flexion, disk degeneration scores, and/or loading characteristics were associated with the occurrence of specific failure modes. Findings. Results indicated that stellate endplate fractures were associated with increased posterior shear forces (P < 0.05) and less degenerated discs (P < 0.01). Fractures running laterally across the endplate were associated with motion segments having larger volumes (P < 0.01). Endplate depression was more common in smaller specimens (P < 0.01), as well as those experiencing increased posterior shear force (P < 0.05). Zygapophysial joint damage was more likely to occur in a neutral posture (P < 0.01).Interpretation. These results suggest that prediction of failure modes (e.g., specific endplate fracture patterns) may be possible (atleast for older specimens)

By Richard J. Mainiero, Marcia L. Harris

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

Dr C. M. van Staden (Fellow): Mr President, ladies and gentlemen, thank you very much for this opportunity to contribute to the paper by Dr Stander, and Messrs Henzen and Funke. First of all, my congratulations to Dr Stander on being re-elected President of the International Association of Water Pollution Research. We in South Africa are proud that this honour was again bestowed on our leading scientist in the field of water research. Furthermore, my congratulations to the authors of this paper. The growth of the pollution problem caused by acidic water discharged from abandoned collieries, is known to most of us. However, I am not aware of any case where an abandoned gold mine is directly discharging polluted underground water. I think it is also a debatable point as to what the quality of underground water being discharged from abandoned gold mines would be in the long run. Any reduction works on a gold mine which practises only fairly good housekeeping, should not cause any water pollution by cyanide. First of all, any cyanide solution before gold precipitation would be too valuable to lose. Secondly, the precipitated solution, which contains the cyanide, is used to pump slime to slimes dams. Any cyanide pollution that may occur at the slimes dam, must come from the top and, fortunately, the days when pen stock water was discharged directly from the top of dams into public streams, have gone. Run-off and seepage is usually acidic, thus decomposing the cyanide. The code of practice by the Chamber of Mines is quite clear on the point as to how the tops of dams should be secured, to prevent any process water or storm-water polluting public streams. The general standards are given on page three of the paper. To my knowledge, under certain circumstances a degree of relaxation can be given regarding the faecal coli count; namely a permissible count of 1 000 per 100 ml. I feel very strongly that research aimed at inhibiting the activity of acid-producing bacteria should be encouraged. Success in this field would be of great benefit to the mining industry. I am very thankful that the authors have mentioned vegetation of dumps as a method to combat water pollution, with the full awareness that the key objective in vegetating dumps is to prevent air pollution. A problem that I have not heard mentioned before and on which I would appreciate the views of the authors, is the pollution that may be caused by power-stations discharging

By M. J. Beus, B. Stewart, S. Iverson

Synopsis U.S. Mine Safety and Health Administration (MSHA) accidents statistics have identified ore-pass hazards as a significant safety problem in U.S. underground metal mines. The statistics show that nearly 75% of injuries are directly or indirectly related to pulling or freeing of ore-pass chutes, the use of hand tools in ore passes, fails of broken rock in ore passes and structural failures of chutes or gates and ore-pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines. Risk assessment methods, such as fault-tree analysis, have been employed to identify the most probable causes of orepass failures, define research priorities and analyse the factors that result in malfunctioning and unsafe ore passes. Static and dynamic loads are being measured in a laboratory setting with the use of a reduced-scale orepass mock-up. Field tests are being initiated in mine ore passes to determine static and dynamic loads. Data from the test ore passes are being compared with data from the mine to characterize true system behaviour. Computer modelling with the use of closed-form solutions, finite-element analyses and a newly developed particle flow code predicts static and dynamic leads from the flow and the impact of ore and waste in the ore pass. Preliminary results indicate that dynamic impacts from ore and waste rock might be considerably greater than expected. The total static load is substantially less than is typically used fur the structural design of chute and gate support members. It is suggested that damping factors, normal and shear stiffness and mass frictional characteristics have a significant effect on particle flow and resulting impact loads. This is being verified with the use of results from laboratory tests, field tests and particle flow analyses. Ore passes are vertical or steeply inclined openings in a rock mass through which ore and waste are transported and where they mar also be stored. A typical underground mining system is shown in Fig. 1. The arrows indicate the locations of ore passes and loading pockets and their relative configurations. The control of material flow is potentially one of the most hazardous operations in underground mining. According to MSHA data. most of the ore pass-related accidents in the U.S.A. are associated with the loading-unloading cycle and removal of blockages from ore passes. In particular, attempts to free ore hang-ups have resulted in multiple fatalities. The hazards are obvious; there is uncertainty as to when the ore will break loose and miners are unable to escape falling rock to a safe location. Although ore passes and chutes and gate systems for underground metal and non-metal mines roust meet the requirements specified in the U.S. Code of Federal Regulations (CFR). Parts 57 and 75, recent structural failures of ore-pass linings and gates have underlined the lack of adequate ore-pass design standards available to both MSHA enforcement staff and mine engineers. Because of the importance of an ore pass to the safe operation of a mine design criteria need to be assessed and new guidelines developed. Researchers at the Spokane Research Laboratory of the Nationals Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines and studying design criteria for ore passes. The near-term goal is to conduct laboratory and field experiments and computer modelling to evaluate the ore-pass design criteria currently used. Literature searches, field site

A Colloquium and General Meeting was held jointly with the Mine Ventilation Society of S.A. in Kelvin House, Johannesburg, on 17th November, 1971, the theme being "The Economics of Mine Ventilation". Professor D. Howat (President) was in the chair. The Colloquium was attended by 150 delegates and was opened by the President at 9.00 a.m. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following Grades: Fellows: Frederich-Wilhelm Volk, Peter Bennet Columbine. Members: Allan Colin Lawrence, Karel Anton van Gessel, Christopher Robert Harrison, Christopher Michael George Wartley, Frank Heinrich Deist, Ralph Morris, Benjamin Johannes Nolte. Associates: Wolf gang Freidrich Gottsman. TRANSFERS From Member to Fellow: Hugh Edward Keith Alien. From Graduate to Member: Errol Vincent Bosman, Christopher Roderick Stewart Needes, Bernard Wessels Holthousen. From Student to Graduate: David Robert Fleming. I welcome the new members to the Institute and congratulate them on their election. CO-OPTION TO COUNCIL The President announced that at the Council meeting held on 5th October, 1971, it was agreed, in terms of Rule 3.9 to co-opt Dr T. B. Beeton to Council. COLLOQUIUM The President welcomed visitors and members. He stressed that the discussion would be informal and that any contributor requiring publication should submit his contribution in writing. He then thanked the authors for providing pre-prints of the papers. After the President had concluded his opening remarks, he asked Professor J. de V. Lambrechts to act as Colloquium Chairman for the day and he, in turn, introduced the three Session Chairmen namely, Dr A. Whillier (Chamber of Mines and President of the Mine Ventilation Society); Mr M. Barcza (Managing Director, Corner House Laboratories); and Mr L. W. P. v.d. Bosch (Chief Consulting Engineer, Union Corporation). The following papers were presented: "Fan efficiency investigation on mines of the Union Corporation, Ltd." by J. A. Drummond. Published in the Journal Feb. 1972. "The design of underground cooling towers" by A. Whilliel&apos;. Published in the Journal, Oct. 1971. "Some aspects of the design of cooling plant installations" by R. Hemp. Published in the Journal, Nov. 1971. "The planning of ventilation and refrigeration requirements in deep mines" by D. F. H. Grave and R. M. Stroh. Published in the Journal, Dec. 1971. "Cooling power of underground environments" by D. Mitchell and A. Whillier. Published in the Journal, Oct. 1971. At the conclusion of the three technical sessions the Symposium Chairman commented as follows, indicating that he would prepare a written summing up at a later stage: "The tone of the colloquium has had a sincerely practical note about it. It would have been a pity if the ventilation experts talked only theory and little practice. This practical theme has, I am sure, made the colloquium interesting to both ventilation men and others whose daily tasks do not touch so closely on this fascinating subject. This practical theme was in evidence through all the papers and contributions. Some of you may have felt that there was not enough emphasis on the word &apos;economics&apos; as advertised in the broad title of the colloquium. I do not think this was really a valid criticism because as someone said &apos;it all boils down to Rands in the end!&apos; So whether it was a case of low fan efficiency, poor design of cooling towers, wrong planning or low human efficiency due to high heat stress. . . it all boils down to money saving and therefore economics, whenever improvements are forthcoming. The title of the colloquium was thus not misplaced. The views of senior mining men on the production side are appreciated. Let us say that this exchange of views between ventilation engineers and those who have to take the final decisions and spend the money, should prove to be most rewarding." Professor Lambrechts finally thanked the Session Chairmen and everybody who had helped to make the colloquium a success and the meeting closed at 4.0 p.m. In a subsequent written summing up, the Colloquium Chairman gave the following as his impressions of some of the highlights which emerged from the papers and discussion thereof: (The names indicate the authors only). Drummond: It was hinted that the time had arrived to consider the introduction of a South African fan test code which would be better suited to local conditions than the currently acknowledged B.S.S. code which, however, is seldom enforceable in practice. In this connection also, there was prominent reference to the thermodynamic approach of McPherson. Wide variations in the quality of maintenance of, and repair work on, fans were stressed. It was mooted that ventilation engineers responsible for estimating the basic duty specifications for large fans, frequently played safe by overestimating the pressure required, thus ensuring that there would not be a shortfall in air volume delivered. This usually meant reduced fan efficiency and it was suggested that decision makers seemed to lay more emphasis on volume of air delivered than on real eco-