Search Documents

By Harry Dobroski, Larry G. Stolarczyk

Medium-frequency (MF) techniques have been successfully .[pplied] to the problem of radio voice communications in both coal and metal and nonmental mines. Long range is achieved by taking advantage of existing mine conductors that carry and propagate the signal over vast areas. It is very likely that in the near future such systems will become the referred method for general mine communications. MF techniques can also be applied to the areas of in-mine control and monitoring. Preliminary work in this area is described. In a western mine, locomotives are being operated under MF remote control in a loading operation. In several eastern mines, MF has been evaluated as a method for monitoring the status of devices in remote areas of the mines. All control and monitor information uses existing mine conductors.

By C. R. McEwen

The displacement equations of Buckley and Lever-ett' have been successfully applied to the prediction of oil recovery in frontal drives for a number of years. Commonly, the capillary pressure term is omitted from Leverett's fractional flow formula. The resulting satura-tion-vs-distance curves become multi-valued, however. Buckley and Leverett, recognizing that the neglect of capillarity was most likely the cause, proposed that this part of the solution he ignored. An ingenious method of propagating a discontinuity in place of the multi-valued portlon of the curve was devised by Cardwell using "non-capillary displacement theory". However, it would seem that a completc description of the displacement pracess would require the inclusion of capillary forces. Three publications on displacement theory have appeared in which capillary pressure was included. Ter-williger. et al', calculated saturation profiles which matched those which they observed when gas displaced water vertically downward. Based on their study, Jones-Parra and Calhoun5 roposed a method of computing saturation distributions sufficiently removed in time from the initial conditions so that all saturations in the flood front region were assumed to move with the same velocity. This latter assumption corresponds to the tangent construction on the flowing fraction-vs-satura-tion curve proposed by Welge." A numerical solution to the problem of water displacing oil from a water-wet porous medium was recently presented by Blair, ef at'. The initial conditions included a uniform saturation slightly above interstitial water saturation. that is, the permeability to water ahead of the front was not zero. This appeared to result in a region of slowly rising water saturation ahead of the front, at least for the particular set of relative permeability and capillary pressure data used to illustrate the computation. The authors also postulated an "end-effect" at the outflow face of the system, whereby no water could pass out of the system until the water saturation had built up to a high value. The saturation profiles computed under these assumptions show water accumulating at the downstream end of the system while the flood front proper is still traveling toward the outlet. The purpose of this paper is to present the results of a numerical solution to the one-dimensional water-flooding equation in which no outlet end-effect is considered and where there is no flow of water ahead of the flood front. It should be noted that the contemporary paper of Fayers and Sheldon8 deals with the problem under discussion. For a thorough treatment including both capillarity and gravity the reader is referred to their paper.

By H. Groeneveld, C. A. Connally, P. J. Hoenmans, J. J. Justen, W. L. Mason

A miscible displacement pilot using a slug of LPG driven by separator gas was conducted in the Cardiurn reservoir of the Pembina field. The injection pattern was a 10-acre, inverted, isolated five-spot. Upon completion of the LPG-gar phase, an experiment was conducted using a slug of water followed by gas. Calculated performance of the pilot is compared with actual performance. Equations are developed to calculate the distribution of LPG into zones of varying permeability, to estimate the progress of the flood at different times in the various zones and to estimate gas rates after breakthrough. The analysis indicates that permeability stratification was a dominant factor in controlling oil recovery and that oil was completely displaced from the swept pore volume. The results of the pilot indicated that miscible flooding is a practical means of pressure maintenance in this reservoir. The total recovery from the pilot area was good in spite of the early breakthrough of LPG. The effects of stratification were reduced by injecting a slug of water into the partially swept reservoir. INTRODUCTION The Pembina field,' located in Alberta, is the largest oil field in Canada and one of the largest in the North American continent. The reservoir is a stratigraphic trap producing from the Cardium sand. Neither bottom water nor free gas has been found. The recovery of oil by the natural depletion mechanism has been estimated at 12.5 per cent. Pressure maintenance studies of various areas have indicated that the recovery can be increased 21/2 times by water flooding, and a large area of the field is presently under water flood. However, reservoir studies of the North Pembina area indicated that miscible flooding might be competitive with water flooding. A pilot test was conducted to evaluate the performance of a miscible flood. A 10-acre, inverted, isolated, five-spot pattern was selected for the pilot. The pattern area was large enough to minimize wellbore fracturing effects and contained sufficient oil to provide significant working numbers. The performance of each of the four producers could be evaluated individually and compared. In the event of breakthrough in one direction, the effect would be isolated from the other producers. The use of a single injector minimized the volume of LPG required, and, because of the high mobility of gas, one well was sufficient to inject the necessary daily volume to replace the high rate of production. With four producers, the test could be completed in time for results to be evaluated, additional engineering studies to be made and a unit to be formed before the reservoir pressure in the North Pembina area declined below the bubble point. The pilot was located in an area developed on staggered, 80-acre spacing. The injection well was drilled at a regular location, while the four producers were drilled 467-ft north, east, south and west of the injector. Each quadrant and its associated producer were identified according to their direction from the injector— that is, north, east, south or west. The eight surrounding producers on 80-acre spacing were shut in to isolate the pilot area and provide for reservoir pressure observation. The pilot wells were completed using permanent-type completion techniques. After coring, casing was run through the pay section and cemented. Inside 51/2-in. casing, 2 1/2-in. tubing was hung. The wells were perforated opposite the Upper Cardium sand and lightly fractured. Fracturing volumes, rates and pressures were low to minimize the extent of the fractures. The fracturing treatments average 1,000 lb of 20-40 mesh sand in 700 gal of a low fluid-loss sand-carrying agent. Feed rates and wellhead fracturing pressures averaged 5.5 bbl/min at 2,535 psig, respectively. After fracturing, the productivity index was measured in each of the five pilot wells. The average PI of the four producers was 0.41 BOPD/psig drawdown. The measured PI'S were approximately the same as PI'S calculated from core analysis data, indicating that the fracturing treatments were just sufficient to overcome

By S. A. Hovanessian

The method of characteristics which reduces the Buckley-Leverett mnlineur, partial differential equation to two first-order, linear differential equations is applied to the solution of a waterffood recovery problem for multiple lines of producing wells and one line of injection wells. The application of the method is described by a numerical example, and a brief theoretical background is given. From the results of this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple sets of producing wells. INTRODUCTION In this paper, the method of characteristics is applied to the solution of a waterflood recovery problem with multiple lines of producing wells and one line of injection wells. The application of the method to this type of recovery problem considerably simplifies the procedure of obtaining a numerical solution. It differs from the method described by Kern1 because it eliminates the need for integration in obtaining saturation fronts. In addition, the saturation history at any location within the field is obtained from a single diagram (time vs distance with saturation as a parameter)'. The paper includes a brief theory of the method of characteristics and its application to the solution of oil recovery problems. A numerical example is worked out, and the cumulative oil recovery-vs-time curve for a system with multiple sets of producing wells is obtained. This curve is then compared with the recovery curve of a system with only one set of producing wells. From this study, it is concluded that the cumulative water injected and oil produced are the same for single and multiple lines of producing wells. However, the recovery time is considerably longer for multiple sets of producing wells.

By J. G. Richardson, J. W. Graham

The purpose of this paper is to present the results of theoretical and experimental studies of water imbibition. The imbibition processes are involved in recovery of oil from stratified and fractured-matrix formations in natural water drives and water flooding. An understanding of the role of inhibition in implementing the recovery of oil from such formations is deemed essential to proper control of these reservoirs to achieve maximum recovery. The theoretical studies involved development of the differential equations which describe the spontaneous imbibition of water by an oil-saturated rock. The dependence of the rate of water intake by the rock on the permeability, interfacial tension, contact angles, fluid viscosities and fluid saturatiorls is discussed. A few experiments were performed using core samples to determine the effects of core length and presence of a free gas suturation. The role of water imbibition in recovery of oil from a fractured-matrix reservoir by water flooding was investigated by use of a laboratory model. This model was scaled to represent one element of a frac-tured-matrix formation. Water floods were made at various rates with several fracture widths. Interpretations were made of the behavior expected in a system containing many matrix blocks. The presence of a free gas sntu.ration was found to reduce the rate of water imbibition. In the reservoir prototype of the fractured-matrix model, water imbibition rather than direct displacement by water was the dominant mechanism in the recovery of oil at low rates. INTRODUCTION Imbibition may be defined as the spontaneous taking up of a liquid by a porous solid. The spontaneous process of imbibition occurs when the fuid-filled solid is immersed or brought in contact with another fluid which preferentially wets the solid. In the process of wetting and flowing into the solid, the imbibing fluid displaces the non-wetting resident fluid. Common examples of this phenomenon are dry bricks soaking up water and expelling air, a blotter soaking up ink and expelling air and reservoir rock soaking up water and expelling oil. As increasingly better lithological descriptions have been made of the characteristics of petroleum-bearing formations, it has become obvious that imbibition phenomena which were once considered laboratory curiosities are of practical importance. For instance, in reservoirs composed of water-wet sand strata of different permeability in intimate contact, the tendency of water to channel through the more permeable stratum is offset by the tendency for water to imbibe into the tight sand and expel oil into the coarse sand. Also, in fractured-matrix formations the tendency of water to channel through the fractures is offset by water-wet matrix blocks. As some imbibition of the water into the of the largest fields in the world are fractured-matrix reservoirs, it has become increasingly important to understand all the factors involved in the imbibition process. Examples of fractured-matrix reservoirs are the Spraberry field in West Texas which produces from a fractured sandstone', the giant Kirkuk field in Iran', the Dukhan field in Qatar, Persian Gulf2, and the Masjid-I-Sula-main and the Haft-Kel fields in Southwestern Iran, which produce from fissured limestone3. Research into recovery of oil from fractured-matrix formations was stimulated by the rapid decline of oil productivity of wells in the Spraberry formation. One result of this research was the water imbibition process developed by the Atlantic Refining Co.4 Another idea was that much of the Spraberry oil could be recovered by conventional water-flooding procedures5. Subsequently, pilot floods were conducted in this field to test the feasibility of these ideas. It was felt that an understanding of the role played by imbibition processes in displacement of oil from a fractured-matrix reservoir could not be obtained from field data alone because of the many complicating factors and uncertainties involved. Therefore, theoretical and laboratory studies were undertaken to provide this understanding. Study of the equations which describe the linear, countercurrent imbibition process provided an insight into the role of various factors in the process, such as the permeability of rock and inter-facial tension. In addition to the theoretical studies, imbibition experiments were conducted with core samples to determine the effect on the rate of imbibition of such variables as core length and free gas saturation. The principal experimental studies were conducted by water flooding a scaled model of an clement of a frac-tu red-matrix reservoir to evaluate

By Walter K. Utt

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. To increase the safety of underground miners, researchers froth the Spokane Research Laboratory of- the National Institute for Occupational Safety and Health are applying neural network technology to rite classification of mine roof strata in terms of relative strength. In this project, the feasibility of using a monitoring system on a roof drill to assess the integrity of a mine roof and warn a roof drill operator when a weak layer is encountered is being studied. Using measurements taken while a layer is being drilled, one can convert the data to suitably scaled features and classify the strength of the layer with a neural network. The feasibility of using a drill monitoring system to estimate the strength of successive layers of rock was demonstrated in the laboratory.

YOUR mom was right …count to 10. Most workers today report that they find their jobs stressful. Miners, in particular, are faced with hazardous and changing environments. Every shift provides different conditions and challenges. Coping with stress is an important tool to maintain your physical and mental health. Now, back to mom. Studies on stress tell us that shifting your focus away from what is causing your stress increases your ability to cope. Counting to 10 is one method. Science proves mom right. The stress response We are born with the stress response, which is a survival instinct, sometimes called the "fight or flight" response. When approached by a tiger in the jungle, our ancestors would perceive danger and prepare to fight or run. The body prepares for the fight or flight response in a number of ways. The bloodstream brings extra glucose and oxygen (fuel) to the heart, the sense of pain is dulled, and memory and thinking improve. The pupils dilate for better vision and the lungs take in more oxygen, while heart rate and blood pressure increase. Body hairs become erect, as puffed-out hair makes an animal look bigger and more dangerous. Once the perceived danger is gone - we have run fast enough to get away from the tiger or won the fight - the body returns to normal functions. Unfortunately, civilization gives us too many opportunities to experience this response. If activated too often, it can create wear and tear on the body, which may lead to injury and illness. Chronic and traumatic stress There are two key types of stress: chronic stress and traumatic stress. Both types can cause both physical and psychological symptoms. Chronic stress builds up from the day-to-day hassles. Traumatic stress results from a traumatic event such as a natural disaster, a mine disaster, or the sudden death of a loved one. Chronic stress is associated with an increased risk of a number of health problems including heart disease, depression, back pain, and carpal tunnel syndrome. Traumatic stress may lead to post- traumatic stress disorder (PTSD), Miners may experience both chronic and traumatic stress in their work.

By R. P. Alger, M. P. Tixier, D. R. Tanguy

In the combination induction-electrical log used at present in the field, the induction logging tool is appropriate for the investigation of moderately invaded formations. A new induction sonde with a radius and investigation about twice as large has been developed recently for the case of deep invasion. It has very nearly the same vertical resolution as the present sonde so that thin beds are defined as accurately as before. The characteristics of the new tool are described, the corresponding interpretation charts are given and field examples are discussed. The design of the sonic logging tool has been modified to improve the calibration and the reliability. The fact that porosity can be accurately recorded by means of the sonic log has prompted new interpretation procedures for saturation estimation, wherein the data concerning the various permeable beds in a given well are correlated. One approach consists of plotting transit time vs true resistivity, with an appropriate scale. With this approach, saturations can be estimated conveniently even in cases where formation water resistivity is not well known. In another approach, a comparison is made of the values of the formation waters computed from the re- sistivity and sonic logs. Using the concept of continuity, this procedure makes possible a quick determination of zones of saturation in shaly sands and/or in case of appreciable variations of formation salinities with depth. It has been found that the comparison of porosity from the sonic log with the apparent porosity computed from a short-investigation resistivity log may reveal, in many cases, the presence of residual oil and thus detect potentially productive formations; this procedure is valuable when the true formation resistivity and the resistivity of the formation water are in doubt. INTRODUCTION During the past year, the efficiency of log interpretation has been vastly improved. The improvements have largely resulted from the introduction of a deep-investigation induction device and from the application of new interpretation techniques that utilize sonic vs resistivity readings. Since the new interpretation techniques depend, in part, upon good values of true formation resistivity, the new induction log will be discussed under Part I. The sonic interpretation techniques will be studied under Part 11. Early in 1959, the 6FF40 induction equipment was introduced in the field. This device was designed for a better approach to true formation resistivities in deeply invaded zones. The greatly improved radial investigation of the 6FF40 equipment has been achieved without sacrificing vertical resolution. The first combination induction-electrical log, the 5FF40, was introduced as a standard tool in 1956 for the logging of wells drilled with fresh muds. The tool has received wide industry acceptance in the United States. 'The 5FF40 induction log has a radial investigation sufficient to overcome average depths of mud filtrate invasion. At 5d invasion, for example, the 5FF40 induction log will read about 1.4 R. in a water sand where R., = 10R,. At 10d invasion, such induction log would read 2.45 R. in the same water sand. In either case, the effects of invasion would not be sufficiently great to cause a water sand to be mistaken for a shale-free oil- or gas-producing zone. Some formations, however, invade deeply — in excess of 10d. Such water zones could be mistaken for oil-or gas-saturated sands unless the porosity balance' can clearly make the distinction. It is for these deeply invaded formations that the 6FF40 was developed. CHARACTERISTICS OF THE 6FF40 Radial Investigation Characteristics To describe the comparative responses of the 5FF40

By L. G. Jones

An approximate method of calculation is developed in this paper which allows duplication of radial unsteady-state gas flow computer results where Darcy's law applies, such as those reported by Aronofsky and Jenkins and Bruce, Peaceman, Rachford, and Rice. Moreover, the new calculation method can be used to obtain results for radial unsteady-state gas flow obeying the quadratic flow law proposed by Duwez and Green. Means are discussed for predicting well behavior at single or superimposed flow rates in finite or infinite reservoirs, determining reservoir rock properties from well-test data, reproducing and interpreting back-pressure test data, and determining the radial extent and reserves of gas reservoirs from well-test data. Example calculations are presented for gas flow following both Darcy's law and the quadratic flow law. INTRODUCTION Since the publishing of U. S. Bureau of Mines Monograph 7,1 most gas-well testing methods have been based on the equation q = y (pl2 - pw2)a, where q = production rate, pl and pw, are formation pressure and sandface pressure, respectively, and y and a are constants to be obtained from test data. These methods, used for predicting both deliverability and "open-flow" capacity of gas wells, have been useful and accurate in many cases but unsatisfactory in others. Even at best, however, they do not supply information about the formation or lead to an understanding of nonsteady-state gas flow in porous media. Many theoretically based studies2-4 of gas flow obeying Darcy's law have been made.' Since the partial differential equations which result from combining Darcy's flow law with the continuity equation are nonlinear, most of the published research consists of either numerical solutions or analytical solutions for linear approximating equations. Such solutions have been of limited value in field work due to their unhandy form and their failure to correlate most field data. There is evidence5,6 which indicates that Darcy's law is inadequate to describe gas flow at some flow rates of practical interest. A quadratic flow law: which reduces to Darcy's law at low rates, is more successful in accounting for experimentally observed behavior. This flow law has been applied successfully to a few hypothetical reservoir cases in work which has recently been published.10 However, these numerical solutions of the equations involved have been successful only on a special analog computer. Routine applications to field cases would be awkward and have not been attempted. The present paper describes an approximate method for computing nonsteady-state gas flow solutions which has been completely successful in predicting the results for both Darcy flow and quadratic flow obtained by elaborate numerical methods. The new calculation method allows determination of the observable variables in gas-well testing at constant rates. It is similar to the scheme of using a succession of steady states suggested by Muskat7 in that it makes use of steady-state and material-balance equations. It also is similar to the work of Aronofsky and Jenkins2 in that the new method includes Aronofsky and Jenkins' stabilized flow equation as a special case. It improves upon both of these calculation schemes in that it accurately describes all portions of reservoir history and suggests means of determining reservoir rock properties from well-test data. This paper deals only with production from a reservoir, in which case the rate is defined as being negative. The reservoir studied here is a homogeneous, disk-shaped porous body of uniform thickness, with all boundaries sealed except the inner radial boundary of the well.

Visit to the Modderfontein factory of A. E. & C. I. Ltd 23rd November, 1972 A full programme was arranged to suit both the mining and metallurgical sections of the Institute. After refreshments were taken and visitors welcomed by the factory management we were split into two groups, viz metallurgical and mining. Book review Stress-relief Heat Treatment of Vanadium Steels by Or G. O. Joy and Or A. M. Sage (21 pp, 77 references).

By Robert G. Nisle

The classic theory of pressure build-up in shut-in oil wells as developed by Horner and van Everdingen is based on two-dimensional radial symmetry in the well-reservoir system. Such symmetry does not exist in the case of a well which parfiially penetrates the producing formation. As a result of this lack of symmetry the use of the classic theory in such cases become questionable. In this paper the mathematical theory has been extended to include the case of partially penetrating wells. Numerical solutions illustrating the up-dication of the equations are presented. The effect of partial penetration on pressure build-up is shown by a comparison of synthetic pressure build-up curves derived from the numerical solution of the equation for partially penetrating wells for various degrees of penetration. It is shown that partial penetration is detectable from the characteristic shape of the pressure build-up curve and that formation productivity may be calculated from the pressure buildup data in a manner identical to that described by the classic theory. INTRO DUCTION The use of pressure build-up data on shut-in oil wells is a well-established technique for the measurement of reservoir productivity. The work of Homer' and van Everdingen' is well known. Since the publication of their pioneering work, others"' have elaborated and extended the technique. These authors have dealt exclusively with the case of wells that completely penetrate he producing formation. Two-dimensional radial symmetry is achieved, thereby, and the problem is greatly simplified. This ideal situation is seldom encountered in practice. But, in spite of this, the technique is often employed anyway. The question, therefore, arises: how much confidence can be placed in the results of such calculations when the data are taken on wells that only partially penetrate the producing formation? It is the purpose of this work to answer this question. Only the single-phase fluid case will be considered. van Everdigen' has presented a rigorous solution of the two-dimensional case, but because of mathematical complexity, this solution has not proved to be particularly useful. Horner' utilized Kelvin's point source solution in two dimensions and showed that it is a sufficiently good approximation for oil reservoir studies. The geometry of the well and the producing formation is illustrated in Fig. l. Geometrically the formation may be described as an infinite slab. The infinite slab is defined as the solid (the porous medium in this case) bounded by two parallel planes. Thus, the slab extends to very great distances in both the positive and negative directions of two of the coordinate axes, but is finite in

By J. E. Warren

To clarify the specific questions raised by J. E. Warren's discussion, the following remarks are offered. 1. It is correct that stratification is assumed in the application of the statistical zonation technique, but this does not constitute a limitation. If, in fact, the reservoir is not stratified the zonation technique will show it. The reservoir is then considered as one zone with a particular distribution of permeabilities. 2. The statistical zonation technique was intended as wells may not be an adequate measure of the lateral permeability changes; e.g., if the data presented in Table A-4 of the subject paper are evaluated on the basis of two crossed classifications with interaction, the variation between zones is significant with a probability greater than .99; however, the variation betwen wells is also significant with a probability greater than .87. It is apparent that the technique suggested by the author can be generalized to provide a powerful method for describing petroleum reservoirs. This generalization can be achieved by treating the core data as a two-way classification to determine the between-zones and the between-wells variations; then, the build-up permeabilities can be analyzed, perhaps on at least-squares basis, to establish the probable distribution of the permeabilities within the zones associated with the individual wells. an additional tool for the reservoir engineer to use together with other techniques and all available information. If pressure build-up permeabilities are available, they should certainly be included. Pressure build-up tests were not available for the reservoir considered in the paper. 3. The proposed correlation of zones between adjacent wells was the best of the techniques that I examined. It is not so much a "measure" as an indication of lateral permeability changes, regardless of whether they are seemingly random or form an obvious trend.

The problem of providing adequate thrust to manually operated rockdrills operating at air pressures of 70 lb/in2g to 80 lb/in2g with the aid of an air-leg is analyzed. It is shown that adequate thrust is provided by an air-leg or the stiff-leg if it is inclined at an angle to the floor of about 25°. However, this requires that the leg react against some support or protuberance, as the friction force between the leg and the floor is inadequate to contain the thrust. Conclusions summarizing optimum thrusts, blow frequencies, penetration rates, drill steel life and bit wear are presented.

By W. H. Somerton

The effects of drilling variable on rotary drilling rates and efficiencies have been studied by a series of laboratory drilling tests. TWO-cone 1.25-in. diameter hits were used to drill vertically upwards into rock samples at corltrolled weights and rates of rotation. Shale, sandstone and specially prepared concrete samples were used in this study. Power input to the ririllirig systeln was measured and drilling chips collected for energy — .size reduction studies. Reasouably good correlations between drilling variables and rates of penetrotion were found. Qrrantities that are difficult to evaluate include rock strength parameters and the effects of bit wear. Effects of bit size and geormetry require further investigation. Analysis of the drilling chips confirmed the premise that, for rocks containing two or more mineral constituents of diflerent strengths, a greater amourrt of rock breakage occurs in the weaker constituent. Drilling conditions which required greater amounts of energy produced finer drilling chips. As bit tooth wear progressed, drilling chips became finer. Efficiency of rotary drilling as a rock breakage mechanism was extremely low. Comparison was made with theoretical energy requirements and with energy requirements for size reduction by comminution methods. INTRODUCTION Many technological developments and innovations have made possible the successful drilling of oil wells by the rotary method to depths exceeding 20,000 ft. Bigger, more powerful rigs, better steels, improved bit design and more careful control of the circulating system have all contributed to this success. Despite these advances comparatively little is known regarding the basic mechanism of rock breakage by the rotary drilling process. Future improvements and, in particular, reduction of drilling costs will undoubtedly require a clearer understanding of the variables controlling effectiveness and efficiency of rotary drilling. Rotary drilling is inherently an inefficient means of producing rock breakage. Loss of energy in transmission from the surface to the cutting mechanism may be large, thus limiting the total amount of energy which may be applied to rock breakage. Increased efficiency may be realized by improved energy transmission methods such as the turbodrill. Conversion of transmitted energy to rock breakage by use of rotating cutter teeth is likewise inefficient. Improvement of cutter efficiency has been obtained essentially by empirical means —changes in bit tooth size, shape and spacing, and tooth deletion to give clean bottom-hole patterns. The present work was undertaken to investigate the factors controlling rates of bit penetration under laboratory drilling conditions. Laboratory drilling apparatus is shown in Fig. 1. The effects of rock strength and bit wear on drilling rates were investigated. Drill cuttings were analyzed to determine the character of breakage and to compare this with other methods of producing rock breakage. VARIABLES INVOLVED IN ROTARY DRILLING Some of the variables controlling bit penetration rates can be studied conveniently by dimensional grouping. R/DN f(F/D2S) or

By E. F. Kingsbury

One of the well-known and important uses of the noble or precious metals has been for electrical contacts. In fact, the elements of this group, comprising gold, silver and the six platinum metals, have been called "noble" because of their ability to resist heat and corrosion, properties which were early found to be of importance in good contacts. Of these, platinum and its iridium alloys, palladium, and silver, have been extensively used. In recent years the electrical industry has been responsible for about one-eighth of the total consiimption of the platinum metals in the United States. Information is not available as to what part of this one-eighth has been used for contacts but it is certainly an important one. Substitutes for Platinum During the past 20 years a considerable number of contact alloys have been proposed in the patent literature largely with the aim of more or less replacing platinum by gold or silver, and some of these alloys are finding increasingly widespread application as the reliability of their performance becomes established. From even the partial data at hand it appears that this substitution by the less precious metals has replaced at least one-half of the amount of platinum that the entire electrical industry would otherwise be consuming at the present time. While the subject is of considerable interest to the metallurgist it is even more so to the electrical engineer and it is surprising that the literature records no systematic and comprehensive investigation along these lines. Practically all the scattered work on noble metal contacts has centered around platinum as a standard and has had two more or less distinct aims. One of these has been the replacement of platinum by cheaper matcrials, and the other, the dcveloprnent of materials of superior electrical performance. The merit of a contact metal has been assumed to be dependent on its infusibility, and since thc more precious metals have the higher melting points there has naturally been an association of the two qualities in the sense that the more precious were

By R. J. Tailleur, M. Rosenberg

Oil well drilling muds prepared with lubricating aids such as oil, graphite or mica will not produce a sufficiently strong protective lubricant film for the bit bearing surfaces under high load conditions encountered in drilling operations. Consequently, the damage to the bearing surfaces resulting from the absence of such a film frequently results in a shortening of the drill bit life. Several different types of extreme pressure lubricating additives for use in muds have been developed. These arlrlitives are capable of providing a protective lubricating film for bearing surfaces subjected to high load pressures. A modified version of the Timken lubricant tester, an instrument commonly used for testing the extreme pressure lubricating properties of oils, is used for measuring and controlling the lubricating qualities of the mud. Comparison tests made in the laboratory with 55/8-in. tricone bits drilling on steel plates immersed in extreme pressure lubricating muds and conventional muds showed that the bearing life of those bits tested in the lrrbricating mud was three to four times greater than obtained with conventional muds. Drilling tests made with extreme pressure lubricating muds in West Texas increased over-all bit life three to fourfold, reduced drilling torque and wear on drill pipe and drill collars. INTRODUCTION Roller bit cones contain roller, ball and journal-type bearings that are subjected to very heavy loading during drilling operations in which the only lubricant available for these bearings is either water or drilling mud. These bearings must be able to operate satisfac- torily in order for the cutting structures on the surface of the cones to be fully utilized. Frequently, the bearings wear to the point that the cones freeze and the bit must be pulled before the cutting structures on the cones become worn. In some instances the bearings continue to turn with severe wear but the cones, which are held on the bit by the bearings, drop off; and this causes an expensive fishing job. In other instances the bearings wear to the point that the cones pinch in causing an undergauge hole and delays to ream the hole. The advantage of increasing bit bearing life is self-evident. Because of inability to control the internal wear of bits while drilling, it was felt that improvement of the lubricating qualities of the circulating mud would be helpful. However, the often-discussed lubricating property attributed to muds has been a rather vague and intangible one. The literature has implied that the oil-emulsion muds are more effective lubricants than non-emulsion muds. Actually, there has been no direct method of measuring the lubricating property of muds which would indicate that one mud was better than another; there has been no way to determine whether the lubricating property of any mud was adequate. Furthermore, in comparing lubricating properties of muds, two qualities should be considered—the coefficient of friction and the extreme pressure lubricating qualities. For example, graphite can reduce the coefficient of friction, but does not provide a strong enough lubricating film to protect bit bearings subjected to high loads. The primary object of the investigation reported herein was to find a method for prolonging the bearing life of drill bits; and considering the heavy loads used in drilling, it was felt necessary to find both a method of measuring lubricating properties under high load conditions and methods of establishing effective lubrication under these conditions. Extreme pressure lubrication deals with that realm of lubrication where metal surfaces are in rubbing contact with each other under very high pressures. These pressures may be quite high, as for example,

By Michael Jatczak

The San Vicente Tunnel Project is an 11-mile water tunnel constructed for the San Diego County Water Authority. One of the many challenges of the project included tunneling a 22,000-foot single-heading tunnel on the western half of the job in varying geology using a 3.66m (12ft) diameter open shield excavator or ?digger shield.? This paper will discuss the design considerations for the temporary liner, the tunneling, and ancillary equipment. It will also highlight the challenges faced while mining this geology, explain the methods implemented to drive this section of tunnel, and discuss the experiences while performing mechanized tunneling in an extensive and varied San Diego geology.

By J. W. Marx, R. H. Langenheim

The authors are to he complimented for a timely presentation of useful information concerning application of heat to oil reservoirs to increase the rate and ultimate recovery of oil. The solution for heated area resulting from constant rate injection of a hot fluid, presented by the authors, and the fluid-flow analogy, solved by Carter,' are particularly interesting in that 110 restriction is placed on the direction of development of the heated area. It is not necessary that the heated area grow radially. Thus the solution could provide useful information for heat injection in any type of well pattern with any specified swept area data. However, it was assumed in the development that the heated region would remain at a constant clevatcd temperature. Vertical heat losses were computed on this basis. Physically. the assumption that the heated region will remain at a constant temperature (independent of distance from the injection point) appears to require that the heat injection medium be stcam, or other condensible gases near the boding point at injection pressure. If a hot liquid below the boiling point or a hot gas considerably above saturation temperature were used, the temperature of the heated region would decrease with distance from the injection well. Lauwerier2 has discussed this problem for a linear system. (See also Jenkins and Aronolsky; and McNiel and Nelson.') Thus, the authors' solution applies more nearly to steam injection than to hot water injection or hot, non-condensable gas injection. Assuming steam as the injection medium, it appears that steam would pass through the constant-temperature heated region and condense upon contact with the unheated sand. The tempcrature in the condensing region would probably be governed by the release of heat of vaporization required for phase equilibrium at the existing pressure distribution. Temperatures in the region would also be influenced by vaporization of hydrocarbon. Thus, it is doubtful that an expression for radial temperature distribution based on heat conduction only (such as the authors' Eq. 9) would have practical significance. As pointed out by Marx and Langenheim, the growth of the heated area under constant rate steam drive will eventually be limited economically by vertical heat loss. The possibility of continuing to move heat economically by cold water injection or by increasing the steam injection rate appears to be a very important consideration. (Movement of liquids away from the injection well should increase injectivity.) Fortunately, the solution presented by the authors may be generalized to thc case of a variable heat injection rate. The general solution is:

By S. P. Kinney, C. E. Wood, T. L. Joseph

In connection with its investigations of the blast-furnace process, the Bureau of Mines, in cooperation with the Minnesota School of Mines Experiment Station, developed a 6-ton experimental furnace. Such a furnace was needed to determine the feasibility of producing ferroman-ganese from Minnesota manganiferous iron ores, a problem of national importance because of the present need for manganese in the steel industry and our small reserves of ferro-grade ores. Furnace operators are reluctant to use new or untried raw materials or to make decided innovations in practice on account of the financial hazard of experimenting with full-scale equipment. A small furnace which can be operated at a relatively low cost is particularly adapted for testing new raw materials and for determining the feasibility of decided innovations in practice. Laboratory experiments, plus whatever information may be available, are valuable but often do not indicate the net result of changes in an operation involving a large number of interrelated variables. From time to time the cooperation of the Bureau of Mines is solicited in connection with problems involving departures from normal procedure. Under these circumstances some sort of a practical demonstration is a desirable forerunner to full-scale operations which appear feasible after small-scale tests. The Aluminum Co. of America was interested in knowing the practicability of smelting a charge of bauxite, iron ore, and limestone, of proportions that would produce slag of the following composition: A1203, 47 to 48 per cent.; CaO, 41 to 42 per cent.; SiO2,4 to 5 per cent.; TiO2, 2 to 3 per cent.; FeO, 1 percent., and MgO, 1.8 percent. In addition to determining whether it was feasible to operate a blast furnace on slag approaching the composition given above, a quantity of slag was needed for a series of experiments that would show the relative ease and cost of extracting alumina from slag which could be made in the blast furnace, as compared to extracting it from raw bauxite. The value of the slag as a raw material