Search Documents

By N. Marusov, D. K. Lowe, J. C. Karp

This paper considers, from an engineering viewpoint, several factors involved in creating, designing and locating horizontal barriers for controlling water coning. This is an effort to consolidate new concepts with previous information so that a reasonable selection of barrier materials, dimensions and vertical position can be made. Coning theories previously developed are briefly reviewed and an effort i,s made to reduce the results of coning-theory calculations to a point where routine calculations can be made with a desk calculator. It is expected that these simplified calculations will give usable predictions of the amounts of improvement attainable with barriers of various dimensions. Apparatus and procedures used for testing the suitability of commercial cements are described and test results are presented. INTRODUCTION Just about as soon as the phenomenon of water coning was recognized as an oilfield problem, there were suggestions that the production of water coning could be controlled or completely suppressed by means of horizontal barriers. It was also suggested that natural barriers such as shale streaks were helpful in restricting bottom-water production. The implication was that wells not having the benefit of continuous shale streaks to suppress bottom waters should, in some way, be supplied with an artificial barrier. With regard to the selection of barrier materials, there are many references which give the merits of liquid barriers.',' These liquids include surface-active agents," recipitates' and emu1sions. There is no real need to review the merits of these materials again. This paper deals with the use of solid barriers which could be made from various cements. The two major restrictions placed on these barrier cements are that (1) they must be commercially available in large quantities, and (2) they must be applicable by means of standard tools and equipment with techniques that have been fully developed and are in general use at the present time. A schematic drawing of a horizontal barrier in a reservoir is shown in Fig. 1. Two maximum stable water cones are illustrated-—-one for the wellbore diameter and the other for a barrier. A maximum stable cone is one that has attained its maximum volume at the critical production rate and is on the threshold of producing water. The volume displaced by each water cone and the rise in water table are indications of the amount of water-free oil produced. Corrections for porosity, connate water and residual oil, of course, must be applied. The water-oil interface which defines a maximum stable cone is called a free surface. It is a surface over which the pressure is constant. This free surface has the shape of a limiting streamline at and below which there is no movement or transport. The shape of the water cone describes the pressure drop in the reservoir. The effect of a completely impermeable barrier on the cone shape is essentially the same as extending the wellbore out to the barrier radius. The placement of a horizontal barrier requires that a horizontal fracture be created using a single-point entry technique. Two methods may be employed for filling this fracture. One method consists of propping the fracture before filling with cement. The other consists of fracturing with fracture fluid, then immediately following with cement

The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,400. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Members shall be not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years' duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R4.00; Annual subscription R14.00 (town), R12.00 (country). Letters of designation: M.S.A.INST.M.M. Associate Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years' duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00(country). Letters of designation: A.M.S.INST.M.M. Affiliates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Affiliate, is at the time of his application, already a Student member, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Affiliates. Entrance fee R2.00; Annual subscription R12.00 (town), R10.00(country). Graduate Members shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years' duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the permission of Council. Entrance fee R1.00; Annual subscription R7.00 (town), R6.00 (country). Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute's financial year in which they attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00 (town), R3.00 (country). Other. The Council has the power to elect to the grade of Member or Associate Member candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed to the Secretary: South African Institute of Mining and Metallurgy, P.D. Box 1183, Johannesburg.

By R. C. Wang, W. M. McKewan

The behaviour of wire ropes used in mine hoisting is not well understood. In an effort to improve this understanding, the structure of round-strand wire ropes was analysed. This report provides a generalised mathematical model that completely describes the geometry of the wires. It consists of two sets of vector equations and is valid for any round-strand wire rope. One set of equations is used to trace the paths of wires that have the form of a single helix. The other is used for the paths of double helical wires. The specific model for a 33-mm 6x1 9 Seale, IWRC, right regular lay wire rope was presented as an example. The paths and the geometric properties of the wires which include the path length per lay of strand, the curvature, and the torsion were determined from this model. In future work, the model could be used to conduct stress analysis for the wires in the deformed rope at a given rope strain and also to study the effect of wear and breaking of wires on strength loss for the various round-strand wire ropes used in mine hoisting.

By D. Litton, H. Dobroski, J. G. Kovac

Since 1910, the U.S. Bureau of Mines (USBM) has investigated practical ways of dealing with the consequences of major fires and explosions in underground mines. The results of this research have had a significant positive impact on the mining community by enhancing mine workers’ chances of surviving an underground mine disaster. Today, the Bureau continues to conduct research in mine disaster mitigation. Much of this work has direct application to search and rescue situations, such as: emergency evacuation through smoke-filled or otherwise unbreathable atmospheres, locating and rescuing survivors from rubble piles, and fire fighting in confined spaces. Three USBM research areas are discussed: (1) Life Support -- This effort is directed toward research into and development of closed-circuit breathing apparatus for use in hazardous environments which are likely to be encountered in the aftermath of a mine disaster. (2) Trapped Miner Location -- A mine disaster may result in the entrapment of miners whose normal escape routes are cut-off. This research activity resulted in the development of transportable seismic technology that can be used to locate trapped miners. (3) Mine Fire Diagnostics -- This research involves developing practical techniques for remotely monitoring how the atmosphere inside a mine changes during a fire, in order to estimate the spread and severity of an underground fire. This information is critical in deciding how best to fight a mine fire, or whether it is safe to mount a rescue and recovery mission.

By D. B. Hobbs, L. W. Kempf, R. S. Archer

Silicon is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13 per cent. of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 25S, Special 17s and 51s of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both 'normal" and "modified" sand castings. Review of Literature The literature on the heat treatment of aluminum-silicon alloys is not very extensive. The following review gives the principal references of which the authors are aware, in which appreciable information may be found.

By Page-Shipp. R. J., Elizabeth Harris

A study of the response of South African white gold miners to exposure to dust in their working environment yielded large quantities of dust data. Analysis of this data (presented in summarized form) reveals a variety of interesting relationships, including the shift-long exposure of different occupational groups, the dust levels due to various mining operations, relationships between different dust-measuring procedures and time trends in dust levels during the shift. The statistical probability of contracting silicosis at various levels of exposure to this dust is reported briefly. A new method of using microscope counts to estimate the respirable mass of dust samples is given in an appendix.

FEBRUARY GENERAL MEETING The January General Meeting of the Institute was held in Kelvin House, Johannesburg on 21st January, 1970, at 4.30 p.m. Mr V. C. Robinson (Vice-President) was in the Chair. There were also present eighteen Members, Messrs M. Barcza, A. R. C. Fowler, R. C. J. Goode, Prof J. de V. Lambrechts, Messrs T. C. A. Meyer, J. A. Nixon, V. C. Robinson and P. W. J. van Rensburg (Council Members), C. A. Border, D. F. H. Grave, S. D. Hill, A. F. Lee, W. L. le Roux, C. S. Macphail, D. L Starkey, S. G. Taussig, W. T. L Wayman and Dr A. Whillier. Three Associate Members, Dr M. I. Brittan, Messrs R. Hemp and M. J. Martinson. One Student, Mr R. P. W. Henrard. Two Visitors, Dr N. G. W. Cook and Mr J. B. Smith. Secretary, Mr D. C. Visser. Total present: Twenty-six. 1. OBITUARY The Vice-President: "It is my sad duty to announce the death of the following members of the Institute: Reginald Gordon McConnell, Member, who joined the Institute on 24th April, 1946 and passed away on 26th September, 1969. James Henry Moore, Member, who joined the Institute on 28th February, 1951 and passed away on 2nd January, 1970. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask those present to stand and observe a few moments silence." 2. MINUTES The Vice-President: "May we confirm the Minutes of the General Meetings held on 15th October and 19th November, 1969, as published in the December, 1969 issue of the Journal?" 3. MEMBERSHIP The Vice-President: "I have pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Member: Woodford Anson Gilbert. Associate Members: Michael John Harvey Tonking, Schalk Willem Vorster, Edward Alfred Cole, Johannes Godlieb Bosch. Graduate: Leonard Raymond Kilpatrick. Affiliates: Clive Frere Knight Pouiton, David Philip Ayliff, Kenneth Gillings, Edward Gilbert East. Students: Stirling Graham Low, Petrus Stephanus van der Merwe, Louis Johannes Fourie, Clive Maxwell Winterstein. MEMBERS TRANSFERRED TO A HIGHER GRADE From Associate Member to Member: Albert Arthur Hazell, Neville Martin Hayne. "I welcome the newly elected members to the Institute and congratulate the members who had been transferred to a higher grade. 4. GENERAL BUSINESS The Vice-President: "I wish to announce that except for the student prizes awarded at the November meeting, Council has decided to make no awards for 1969. Are there any further matters to raise under the heading of General? If not, we will proceed to the next item on the agenda which is the presentation of tonight's paper. 5. PAPER FOR PRESENTATION The Vice-President: "Professor Starfield may I call on you to deliver the paper entitled "A rapid method of calculating temperature increases along mine airways". After the presentation of the paper, the Vice-President said: The Vice-President: "Thank you very much, Professor Starfield. Gentlemen, I think that many of you here, who have to do with the design of mines in an age where costs and difficulties generally, are increasing at a rate which we find almost impossible to keep up with, I would agree with you that we are fortunate to have a band of people like Professor Starfield, and others who are dedicated to producing the tools, and methods which we need to sort out these problems. I am sure that you would agree with me, that the old rule-of-thumb methods are finished forever, that we can never go back to the methods which served us in the past, when we were close to the surface and had not met the conditions which we are meeting now, and which we are going to meet in an increasing degree in the future. It is to people like Professor Starfield, with these clear, completely logically described new methods, that we look for the solution of our problems in the future. I think the whole problem of layout of any mine, is one where you can reliably prognosticate what you are likely to find in a variety of circumstances to meet the wide range of things which must happen when you consider the costs in these modern operations. Thank you very much, Professor Starfield, for coming and giving us this paper. Thank you for making plain to me how these mathematical models of yours are used. I am sure that what you have said will be a very valuable addition to the archives of this Institution. Thank you very much, indeed, and Gentlemen, will you please show your appreciation in the normal way." (Applause). Professor J. de V. Lambrechts, Mr R. Hemp and Dr A. Whillier then contributed to the discussion. (These contributions will appear in a later issue of the Journal.) PAPERS OPEN FOR DISCUSSION The Vice-President: "Listed on the agenda are papers open for discussion. I would suggest that anyone wishing to contribute to these papers submit their contributions to the Secretary in writing." CONCLUSION The Vice-President: "I wish to thank members and visitors for their attendance, and now declare the meeting closed." The meeting closed at 5.30 p.m

By William M. Courtis

Since many accounts of Silver Islet Mine, in Lake Superior, have already been published, it is supposed that the members of the Institute are familiar with the location and character of the mine. To many, however, a more detailed account of the ore and manner of treatment will, perhaps, not be without interest. The extraordinary richness of Silver Islet ores, and the difficulty of obtaining correct assays, induced the company to erect smelting works of its own. Accordingly, ground was broken at Wyandotte; Mich., early in the spring of 1871, and the work was pressed on with indomitable energy by Captain E. B. Ward of Detroit, as president, and Mr. Thomas MacFarlane, the discoverer of Silver Islet, as superintendent of the works, so that by July 1st the works were so far completed that smelting could be commenced. The intention was to work Western ores with those from Lake Superior, since the latter contain but a small amount of lead. Hence the capacity of the works is much larger than is needed for the present yield of the mine. The planned process for treatment was smelt-

By O. Norman Lotter

The formulation and use of mixed collector suites in sulphide flotation can be traced back as far as 1957 with the work of Glembottskii and his co-workers in Moscow. The subject was reviewed by Lotter and Bradshaw in 2010, and proposed a synergy between ideally-selected different reagent types to deliver improved performance, in particular the in situ catalysis of a xanthate to dixanthogen by a dithiocarbamate. Correctly formulated for a particular application, an optimally arranged mixed collector suite delivers the following improvements to the flotation process: • An increase in the flotation kinetics • Improvement in coarse, or middling, particle recovery • Reduction in total dosage requirement • Best results are found from testing the ratios of the collectors. This is of critical importance. In all an optimally formulated mixed collector system usually delivers an increase in paymetals recovery of 1–4% absolute, with a gain in concentrate grade in the range 10–20% relative. In recent years, the addition of semi-conductor theory and associated electrochemistry has contributed significantly to this toolbox by way of identifying optimum domains of Eh and pH for the flotation of individual minerals. In the case of mixtures of minerals, this is where the mixed collector system delivers significant value by way of presenting a mixed set of collector radicals and dimers in a common Eh and pH domain for overall performance. This calls on a fundamental understanding of organic chemistry, mineralogy, semiconductor theory, and electrochemistry. Whereas the selection of grinding media type effectively influences the Eh, the pH can be easily controlled by pH modifiers. The theory of this system, and some industrial case studies, are discussed.

By John J. Sammarco

Mining, traditionally a low-tech industry, is now utilizing surprisingly complex programmable electronic (PE) systems. The functional safety of PE-based mining systems is an international issue and concern. From 1995 to 2001, there were 11 PE-related mining incidents reported in the U.S. and 71 PE-related mining incidents reported in Australia. These incidents are due, in part, to unprecedented levels of system complexity. The National Institute for Occupational Safety and Health (NIOSH) is addressing this issue of system complexity by conducting research to develop a quantitative complexity assessment methodology based on Normal Accident Theory (NAT). The methodology models the behavioral interactive complexity at the level of system requirements. A graph-theoretical approach is used for creating quantitative metrics from Software Cost Reduction (SCR) dependency graphs. This complexity assessment methodology will help realize simpler, safer systems that will be easier to validate and verify. The methodology will benefit mining and other industries as well.

By T. Egleston

During the last winter we have been actively engaged in the School of Mines in search for boracic acid. This has been owing to the fact that Mr. M. W. Iles, assistant in the qualitative laboratory, has discovered a test for that substance which makes its discovery exceedingly simple instead of being, as previously, very difficult. It consists in powdering the mineral, calcining it, then moistening it with sulphuric acid, and heating on a platinum wire until the sulphuric acid is expelled. It is then moistened with glycerin and made to take fire. If boracic acid is present it infallibly gives a green flame. It is not at all surprising, under such circumstances, the test being so easy, that boracic acid has been found by the students in a great many cases where its presence was not previously suspected, and in some where its detection was previously too difficult to warrant looking for it. We were not prepared, however, for its discovery in Lake Superior iron ores, and were disposed at first to think that a mistake had been made. After, however, it had been frequently reported in these ores it was considered worth while

The Institute was founded in 1894 as the Chemical and Metallurgical Society of South Africa. In 1904 it was reconstituted as the Chemical Metallurgical and Mining Society of South Africa and in 1956 it became the South African Institute of Mining and Metallurgy. The objects of the Institute are to advance the science and practice of mining and metallurgy, to afford opportunities for the interchange and recording of knowledge of mining and metallurgy and to ensure high standards of professional conduct and competence. Membership benefits include monthly issues of the Journal of the Institute, monthly General Meetings at which papers are read, symposia, excursions to mining and industrial concerns and the use of club facilities at Kelvin House. Technical journals received on an exchange basis are available to members at the Johannesburg Public Library. The current membership of the Institute is over 1,600. Membership applications are accepted from suitably qualified persons and the requirements for entrance to the various grades of membership are summarised below. Fellows shall not be less than 30 years of age, shall be university graduates in pure or applied science or shall produce evidence to the satisfaction of the Council that they have successfully completed a co-ordinated course of study in pure or applied science of at least three years' duration at an approved university or institution deemed by the Council to be of equivalent status. Members shall have been employed in senior technical positions in important mining or metallurgical undertakings for at least five years or they shall have practised as mining or metallurgical consultants for at least five years. They shall be practising their profession at the time of application. Entrance fee R10.00, Annual subscription RI7.00. Letters of designation: F.S.A.I.M.M. Members shall be not less than 25 years of age and shall be university graduates in pure or applied science, or shall have successfully completed co-ordinated courses of study in pure or applied science of at least three years' duration. They shall have been engaged in work of an approved technical character in the mining or metallurgical industries, of which not less than two years shall have been in positions of responsibility. A candidate shall be practising his profession at the time of his application. Entrance fee R8.00, Annual subscription RI5.00. Letters of designation: M.S.A.I.M.M. Associates shall be not less than twenty-five years of age, and shall have been engaged in positions of responsibility in, or associated with, the mining or metallurgical industries for periods of not less than three years. If, however, the candidate for admission to the higher grade of Associate, is at the time of his application, already a Student, he need satisfy the Council only that he is, at the time of his application, engaged in a position of responsibility in or associated with the mining or metallurgical industries. In all cases the applicants shall satisfy the Council that they are fit and proper persons to become Associates. Entrance fee R8.00, Annual subscription R15.00. Graduates shall be not less than 21 years of age and shall be university graduates in pure or applied science, or have completed co-ordinated courses of study in pure or applied science of at least three years' duration at an approved university or institution. They shall not remain Graduate members after attaining the age of 30 years without the permission of Council. Entrance fee R2.00, Annual subscription R10.00. Students shall be persons not less than 18 years of age who are being educated or trained in a manner approved by the Council, to occupy a technical position in or associated with the mining or metallurgical industries and who, furthermore, shall not have attained the qualification required for a higher grade of membership. They may remain Students until they have obtained the necessary qualifications for transfer to a higher grade of membership, but not after the end of the Institute's financial year in which they attain the age of 28 (twenty-eight) years. They shall then transfer to a higher grade to retain membership of the Institute. The Council may relax the provisions of this clause in such cases as it considers appropriate. Entrance fee nil; Annual subscription R3.00. Other. The Council has the power to elect to the grade of Fellow or Member, candidates who may not fulfil all the requirements for entrance to these grades but whose status, professional achievements and practical experience in mining or metallurgy justify such election. Applications. Requests for membership application forms should be addressed on the attached form to the Secretary, South African Institute of Mining and Metallurgy, P.O. Box 61019, Marshalltown, Transvaal.

By Jun Enriquez

Kennecott Utah Copper aims to extend anode furnace campaigns to more than three years. As part of that goal improvements are sought on anode-furnace tuyere-area refractory performance. Kennecott and Praxair developed high pressure nitrogen refining for the Oxidation Stage which shortened anode furnace fire refining cycles by up to two hours per cycle. Future developments include optimizing the Reduction Stage’s steam-gas reforming and achieving coherent jet tuyereless refining.

By Frederick Prime

TO an association like the one before which I read this paper, few questions can be more important and constantly recurring than the following, viz.: "What economy can be effected in the manufacture of American iron?" And it is the one with which I purpose to deal in this paper ; premising, however, that my object is merely to indicate the direction in which an answer should be sought for, rather than to give it myself. This subject may be divided into two parts, "Economy in the production of pig-iron," and "Economy in the manufacture of wrought-iron ;" but it is to the former alone that I shall confine myself this evening.

By R. Karl Zipf

Multiple seam mining interactions caused by full extraction mining, whether due to undermining or overmining, frequently involve tensile failure of the affected mine roof. The adverse ground control conditions may prevent mining for both safety and economic reasons. Prior researchers have identified the geometric, geologic and mining factors controlling multiple seam mining interactions. This numerical study examines the mechanics of these interactions using a modeling procedure that 1) incorporates the essential constitutive behavior of the rock such as strain-softening of the intact rock and shear and tensile failure along bedding planes and 2) captures the geologic variability of the rock especially the layering of weak and strong rocks and weak bedding planes. Specifically, the numerical study considered the effect of vertical stress, interburden thickness, and the immediate roof quality of the affected seam in both undermining and overmining situations. The models show that for overburden-to-interburden thickness (OB/IB) ratios of less than 5, interactions do not occur, and that for OB/IB more than 50, extreme interaction is a certainty. In between, the possibility of an interaction was found to depend on gob width-to-interburden thickness ratio, site specific geology and horizontal stress to rock strength ratio in addition to the OB/IB ratio. The models also showed that horizontal stress was profoundly altered well above or below a full extraction area and that these changes are likely to influence the success or failure of multiple seam mining. The role of horizontal stress in multiple seam mining interactions has received little attention in prior investigations. Four factors control the mechanics of multiple seam mining interactions: 1. vertical stress concentration 2. horizontal stress concentration 3. stress re-direction 4. bedding plane slip bands A combination of vertical and horizontal stress increase and high stress gradients in the vicinity of full extraction areas re-orients principal stresses into a very unfavorable direction. This seemingly small stress re-orientation has a profound adverse effect on bedded rock.

The Registrar has requested us to publish the following notices: COUNCIL'S POLICY REGARDING LATE APPLICATIONS IN TERMS OF SECTION 18(4) (b) OF THE PROFESSIONAL ENGINEERS' ACT, 1968 (ACT NO. 81 OF 1968) Laat aansoeke om registrasie as Professionele Ingenieurs Die Suid-Afrikaanse Raad vir Professionele Ingenieurs (SARPI) vestig die aandag daarop dat daar 'n mistasting bestaan oor die vraag of 'n persoon sonder erkende ingenieurskwalifikasies wat nie in 1969 aansoek gedoen het om registrasie as professionele ingenieur nie, nie meer aansoek mag doen nie. Diegene wat voor 14 Februarie 1969 minstens 3 jaar aanvaarbare ingenieurswerk gedoen het kan nog oorweeg word. Die werk moet egter voldoen aan die standaarde deur SARPI neergele: dit Suid-Afrikaanse Road vir Professionele Ingenieurs DIE WET OP PROFESSIONELE INGENIEURS, 1968 (WET NO. 81 VAN 1968): JAARGELD: 1972/73 BOEKJAAR Kragtens die bepalings van Artikel 18(9) (b) van die Wet verval die Registrasie van 'n persoon wat as 'n ingenieur of ingenieur-in-opleiding geregistreer is as sodanige persoon versuim om die voorgeskrewe jaargeld binne ses maande nadat dit betaalbaar word, te betaal. Aandag word ook vriendelik daarop gevestig dat persone wat kragtens Artikel 18(4) (b) van die Wet geregistreer is (dit wil se persone wat nie oor 'n erkende akademiese kwalifikasie beskik nie) en wat toelaat dat hulle registrasie verval, moontlik nie weer vir registrasie in aanmerking sal kan kom nie. Vir persone in hierdie kategorie is dit dus van kardinale belang om toe te sien dat hulle jaargeld binne die voorgeskrewe tydperk betaal word.

By William Gleason

The evolution of technology has made the world a more connected place. It continues to change the way we power our homes and vehicles and is leading to a future that seems to be limitless. Limitless as long as we can continue to supply the minerals necessary for technology to produce better iPhones, more efficient electric cars, better wind turbines and sophisticated national defense systems. These minerals, dubbed critical minerals, have surged in importance in every corner of the world and, on Aug. 3-4, they were topic of conversation at the Critical Minerals 2014 conference in Denver, CO. The conference, hosted by SME and the Australasian Institute of Mining and Metallurgy (AusIMM), looked at critical minerals from every angle, from where they are found to what the future might be. Among the minerals that have been called critical are rare earths, a collection of 17 minerals that have become increasingly important as technology continues to advance in everything from communications to energy to national defense. Leading off the conference, David Abraham, senior fellow at the Institute for Analysis of Global Security, explained that, like many people, he is relatively new to rare earths. Unlike most people, though, Abraham developed more than a passing interest in the minerals and has since travelled the world to understand the role of rare earths ? where they are found, how they are mined, how they get to market and, eventually, what applications they are used in. Following his travels, he said he returned concerned about the sector and how the industry will keep up with the demand that only seems to be growing in the modern world. And, Abraham noted, that it is not just the developed world that is driving demand. It stretches even to places like Indonesia, where the average annual income is about $3,000/year. Yet, the nation is one of the most active places in the world for social media with a population that is wired in with all kinds of electronics. The problem facing the sector is, and has been for a long time, and especially since 2010, supply of the minerals. At one time, China produced about 98 percent of the world?s supply and controlled the sector completely. In 2010, as the world began to demand more rare earths and develop other sources, China announced an export ban on rare earths. This changed the game completely, from the production lines all the way to the floor of the U.S. Congress.

By Youn-Bae Kang

In order to overcome weak points of steel for its engineering applications, in particular, for environmentally benign, energy-efficient, lightweight engineering systems, a number of new steels have been proposed, especially to improve strength-to-weight ratio (specific strength). Mass production of these steels, however, has encountered a serious roadblock particularly in the steel refining and casting processes. This is because their chemistries and cleanliness requirements are vastly different from those of the conventional steels, and thus an incremental improvement of the prevailing process technologies is found hard to meet the requirements. In this study, a new process is proposed, which employs inert gas bubbles in the shroud nozzle, liquid steel drops in the degassing chamber, and the siphon transport for continuous casting. The proposed process which integrates the final refining and cleaning steps prior to casting is expected to be a technologically disruptive innovation on the conventional counterpart. The effectiveness of the individual steps is discussed with experimental results.

By Elaine T. Cullen

Miners, like many skilled blue-collar workers, are not traditional learners. They have not always been successful in classroom-type settings, preferring to learn on the job in a hands-on environment. U.S. law requires that miners have a minimum of 8 hours of safety training annually, plus 40 hours for underground miners and 24 hours for surface miners when they enter the industry. However, miners rarely view this training time positively. In fact, it has been called “safety jail” by many, who regard it as a time to get a little extra sleep While mining has become far safer in the past 100 years, it is still a dangerous occupation. The Office for Mine Safety and Health Research, a part of the National Institute for Occupational Safety and Health (NIOSH), has funded a project for the past 4 years to address this challenge. The purpose of the research was to find a way to develop effective safety training for these people. Miners are born story tellers. They share “near miss” stories, stories about master miners they have known, and stories about how things used to be. These stories not only pass along information about what will happen if a miner fails to respect the mining environment, they also instruct listeners in the culture of mining and the values that it embraces. Stories, it seems, are a way to get safety messages across to miners, especially inexperienced ones, and using older, wiser miners in these stories is an obvious choice. This paper will discuss how a series of training videos was developed, how “master miners” and story lines were chosen, and how the resulting videos have been received in the mining industry.

By R. Simon

The sources of energy dissipation for concentrated loadings on rock are considered in an attempt to account for the experimentally measured magnitude of the work required to break out a unit volume of rock from the free surface of an essentially semi-infinite medium. It is concluded that most of this work probably represents the elastic strain energy developed by the loading in a much larger volume of rock beneath the loaded region than the volume of the rock fragment broken out to the side of the loaded region. This strain energy is largely dissipated in the form of stress waves generated by the high rate of unloading produced by the propagating cracks. The energies associated with the formation of the new surfaces of the cracks and with the stress waves generated directly by the loading process are computed to be negligibly small. Possibilities for improving the utilization of energy to drill rod. subject to the geometrical limitations imposed by down-hole operation, are discussed. It is pointed out that any such possible improvements would probably have to be differential ones, since each rock configuration of more favorabIe loading geometry that can be created down the hole is accompanied by a complementary configuration of less favorable loading geometry. INTRODUCTION Dislodging each cubic inch of rock from the bottom of the hole by the action of a bit requires the expenditure of an amount of energy that varies from approximately 5,000 in.-lb to approximately 100,000 in.-lb, depending on the hardness of the rock, or, more technically, upon its fragmentation strength.1 In this paper we will discuss (I) why the energy expended in drilling is so large, (2) what happens to this energy upon completion of the drilling process, and (3) what are the possibilities for reducing the magnitude of the energy required to drill rock. DETERMINATION OF ROCK DRILLING ENERGY The volume of rock removed per unit time from the bottom of a hole of diameter D is evidently (7/4)D2R, where R is the rate of penetration of the bit. If P is the rate at which work is done by the bit on the rock at the bottom of the hole, the energy required to break out a unit volume of rock is given by: Ev =(4/p) P/D2R............(i) For rotary drilling, of either the rolling-cone or drag-bit varicty, P = 2pLN, where L is the torque resistance to rotation at the bottom of the hole and N is the rate of rotation of the bit. L is essentially the same as the torque measured at the rotary table only when drilling in shallow holes. The energies expended in rotating the drill string against the frictional resistance of the walls of the hole and and against the viscous drag of the drilling fluid are extraneous to the subject under consideration, although these may be much greater in magnitude than E, when drilling in a deep hole. For percussion drilling, P = fE where f is the percussion frequency and E is the work done on the rock per impact. The latter quantity can be both computed and measured for a percussion drilling machine. 2 (Under satisfactory drilling conditions, defined in terms of ranges of numerical values of certain dimensionless parameters, E is only 30 to 50 per cent less than the impact energy of the striker.2) Alternatively, E, may be measured directly by dropping chisels shaped like bit edges, backed by rigid weights, onto the surfaces of laboratory rock samples of effectively semi-infinite extent. Under these circumstances, essentially all of the impact energy is converted to work done on the rock, and the relationships among volume of rock broken out, chisel shape, impact energy and indexing distances can be obtained.3 The values of the energy required to break out a unit volume of rock under favorable circumstances are substantially in agreement for rotary drilling, percussion drilling and drop testing at atmospheric pressure. The energy per unit volume is a quantity of the order of magnitude of roughly twice the com-pressive strength of the rock as measured by a uniaxial loading test. The phrase "order of magnitude" in this paper means from about 1/3 as much to 3 times as much; i.e., the energy per unit volume may range from roughly the same up to several times