Search Documents

By K. Hodgson, J. P. M. Hojem, N. G. W. Cook

Already about one-third of South Africa's coal is mined at depths exceeding 100 metres. Almost all this mining is done by the bord and pillar method. Conventional design procedures call for ever larger pillars as depths of workings increase, resulting in the loss of large amounts of coal and reductions in productivity. Barrier pillars are in general use to ensure against large collapses. The presence of these strong pillars would allow a more efficient design of the bord and pillar layout to yield improved extraction ratios by using smaller, yielding, pillars between the bords. Knowledge of the complete load- displacement curves for such pillars is a prerequisite for the design of such a system. A 100-MN, stiff jacking system for measuring the complete load-displacement curves of pillars with cross-sections of up to 2 m X 2 m is described. The jacks are installed in a slot cut across the central plane of symmetry of a pillar, thereby ensuring that the stress distribution in the pillar during a test, especially at its contacts with the roof and floor, is identical to that caused in a similar pillar by convergence across the seam. Preliminary results in the form of complete load-displacement curves for test pillars of about 1.5 metre square section are given.

By C. D. Stahl, E. E. Templeton, R. F. Nielsen

It has been customary, in predicting saturation changes, to use the Leverett fractional flow formula", obtained by eliminating the unknown pressure gradient from the generalized Darcy equations for the separate phases. The formula presents difficulties in the case of counterflow, since the "fractional" flow may be negative, greater than unity, or, in the case of a closed system, infinite. Recently, it has been shown by several authors that the corresponding equations (with capillary pressure and gravity terms) for actual flow of the phase may be used just as well. These equations are in agreement with Pirson's1 statement that, if the two mobilities differ considerably from each other in a closed system, the flow is largely governed by the lower value. The present study was undertaken because of an apparent lack of experimental data on gravity counter-/low with which to test the theory. A 4-ft sand-packed tube in a vertical position was employed. Electrodes for determining saturations by resistivity were spaced along the tube, one phase being always an aqueous salt solution. Air, heptane, naphtha, or Bradford crude oil was used for the other phase. A reasonably uniform initial saturation was set up by pumping the phases through the system, alter which the tube was shut in and saturation profiles obtained at definite intervals. Cumulative flows over certain horizontal levels were obtained by integration of the distributions; hence, differentiation of the cumulative flows with respect to time gave instantaneous flow rates. To compare experimental and theoretical flow values, capillary pressures were assumed given by the final saturation-distribution curve. The upper part corresponds to the "drainage" region and the lower part to the "imbibition" region, where trapping of the nonwetting phase occurred. While calculations indicated that the capillary pressure saturation function and, probably, the relative permeability saturation functions changed during the segregation, the relation of the measured rates to saturation distributions are in general accord with the frontal-advance equation. It appears that the Darcy equations, as modified for the separate phases, are generally valid for counterflow due to density differences. The usual method of predicting saturation changes, which involves a continuity equation and the elimination of the unknown pressure gradient from the flow equations, should therefore be applicable. However, the need for advance knowledge of drainage and and imbibition "capillary pressures" and relative permeabilities during various stages presents difficulties. INTRODUCTION The present study was undertaken because of a seeming lack of experimental data relating to vertical counterflow of fluids of different densities in porous media. In particular, it was desired to determine whether data obtained from these laboratory tests were in accordance with certain mathematical treatments of counterflow which have been proposed. The gravity "correction" has been incorporated into the flow equations (and, hence, into displacement theory) nearly as long as both have been used. field4 and laboratory5 data have generally borne out the validity of the theory as applied, for instance, to downward displacement by gas, with all fluids moving downward. However, the modifications for counterflow have only recently been pointed out. 2-3 It has been customary to use fractional flow rates instead of actual flow rates in displacement calcuIations. In the case of counterflow, this results in negative values, values greater than unity and, when rates are equal and opposite, in infinite values. As pointed out by Sheldon, et a1,3 and by Fayers and sheldon,2 actual flow rates may be used just as well. The fact that these may be of opposite signs for the two fluids does not present any difficulty.

Minutes of meeting held at the Moth Hall, Witbank on 13th November, 1969. There were present eleven members: Mr J. Meintjes (in the chair); Messrs I. E. van Aswegen, O. T. Wright, A. W. L. Brereton, A. Bain, J. Brook, P. J. Beukes, C. H. Coxon, B. F. v.d. Merwe, A. C. Hofmeyer, G. E. Carlyon. Six Associate Members: Messrs E. J. Jackson, J. N. H. Pritchard, R. E. Powell, W. Weber, R. Smith, B. T. Hosking. One Student Member Mr M. J. de Beer. Seven visitors. The Chairman reminded members of the intended visit to Barberton. Dr Stander, Director of the National Institute for Water Research, gave an interesting talk, illustrated with slides and a short film, on the conservation and reclamation of water in South Africa. After question time, Mr Hector, Witbank Town Engineer (visitor) thanked Dr Stander. The meeting closed at 7.10 p.m.

By J. Duran

Mining at Newmont Mining?s Phoenix?s Mine is currently done by surface operation in the Fortitude and Bonanza pits at a combined rate of approximately 100 kt/d (110,000 stpd). A portion of the orebodies targeted by these pits was mined previously by underground mining methods, dating back to the mid-to late-1800s. Most of the underground workings (voids) are located in the west central area of the Bonanza pit. The surface operation requires excavation through voids, and there is a risk of pit floor subsidence that has to be addressed. This article presents a review of the risk mitigation measures that were implemented to reduce risks to people and equipment working in the area.

The sphere of operations of dry crushing has been so much enlarged of late years that the following notes with reference to its advantages and limitations, and also some practical results in connection with the crushing of gold ores will probably be of service to the members of the Institute. Until recently, with one notable exception that of the Mt. Morgan Gold Mine, dry crushing has only been practiced to a very limited extent in Australasia, and elsewhere it might be said to belong to industries other than mining Its sphere of usefulness depends on the fact that the' product is delivered in a dry state without the separation of the finer particles from the coarser to any appreciable extent, thus enabling the following advantages to be achieved with different ores.

By R. S. Conti

The US Bureau of Mines (USBM) has developed an inflatable feed-tube seal (IFTS) for high-expansion foam generators. The IFTS is a lightweight, portable, rectangular inflatable bag that can be used by firefighters to rapidly seal large openings, such as those in underground mines, and to simultaneously provide a feed-tube for a high- expansion foam generator. Thus allows fire-fighting foam to freely flow to the fire site and control or extinguish the fire. Studies indicated that a high-expansion foam plug will travel 183 m (600ft) down an entry with a 4.5% rise in elevation, before leakage of foam from around the inflatable partition.

By H. A. Jr. Koch, C. A. Hutchinson

Miscible phase displacement of oil from reservoirs has been emphasized in the past few years. The reason for this emphasis lies in the high oil recovery attainable by this process. Removal of capillary effects in the reservoir leads to recoveries approaching 100 per cent in the area contacted by the miscible phase. The miscible slug process is one means of obtaining a miscible displacement. Here a band or slug of I,PG is injected into the reservoir prior to gas injection. The idea is to maintain the band of LPG "wedged" between the gas and oil phases and thus achieve a miscible phase displacement. A second method lor achieving miscibility is through the injection of a gas which is not miscible with the reservoir fluid but which develops a zone of miscibility in [he reservoir through mass trans-ier with the reservoir oil.' This mass transfer results in either an enrichment of the lean injected gas by intermediates from the oil or an enrichment of the oil by intermediates from a rich injection gas or one that has been enriched on the surface by LPG addition. We are interested here in discussing the process in which miscibility is developed at the displacement front by the evaporation of interrnediatcs from the oil phase into the gas phase. This process "builds up" its own slug of miscible material at the displacement front and therefore does not require the injection of LPG to obtain miscibil-ily. Each process has its own area of applicability. Generally, the high pressure gas process is applicable only with reservoir fluids which con-!ain a high concentration of inter- mediates. If the high pressure gas process is technically feasible at pressures less than 4,500 psi, it is probably more desirable economically than the slug process. The slug process has broad applicability in the shallower reservoirs and with reservoir fluids which contain a relatively low concentration of LPG and natural gasoline constituents. This paper deals with some new concepts of the high pressure gas injection process where it is proposed that flue gas can be substituted for hydrocarbon gas without sacrificing our goal of miscibility. MECHANISM Introduction Considerable effort has been devoted to study of the mechanics ot the high pressure gas injection proc-one generalization result-ing from some of these studies was that the composition of the injected gas is relatively unimportant in establishing the miscibility pressure* for a given reservoir fluid. This generalization is correct for the composition range of gases typically encountered in the field. Two such gases are a gasoline plant tail gas containing 85 per cent methane and 15 per cent ethane, and a field separator gas containing 70 per cent methane and 30 per cent heavier components. The most important factor which sets the miscibility pressure in the operation is the reservoir fluid composition, particularly the concentration of LPG-natural gasoline constituents. The injected gas is the agent by which the LPG-natural gasoline constituents are concentrated at the displacing front to create a miscible displacement. Based on these results, it appeared feasible that some inexpensive gas, such as flue gas, might be substituted for hydrocarbon gas for use in the high pressure gas process. A re-examination of the phase relations of the high pressure gas injection process should clarify the principle behind using flue gas (essentially nitrogen) as an injection gas. Three Component Diagram The phase relations of the high pressure gas injection process have been illustrated by the use of the three component diagrams.'," In Fig. 1 we have arbitrarily represented the multi-component reservoir system by three components; methane, ethane through hexane, and heptanes plus. The solid curve ABC is the phase boundary curve. It represents the locus of compositions which have fixed saturation pressure at a fixed temperature; the lower branch AB shows bubble point compositions, the upper branch BC, the dew point compositions. Point B is the coniposition of the critical mixture at this temperature and pressure. The dashed lines (tie lines) connect vapor and liquid compositions which are in equilibrium. Let us consider Reservoir Fluid D which we wish to displace in 21 miscible manner by gas injection. Let us further restrict the discussion to the case where miscibility between an injection gas and the reservoir fluid at the displacement front is developed by gas enrichment in the reservoir. For this case, any gas whose composition lies between Points C and E on the right side of the three component diagram can be used to give a miscible displacement of Reservoir Fluid D. This is true because the more mobile injected gas moves faster than the displaced oil and is in continuous contact with virgin oil at the displacement front. This leads to a continuing enrichment 01' the gas at the displacement front by evaporation of the C, - C,

By Brian P. Stapleton, Bill M. Stewart, Joel R. Warneke, Curtis C. Clark

Of the 28 accident/injury classifications listed by the Mine Safety and Health Administration, handling materials is second only to roof falls in terms of generating the highest number of reportable accidents in active underground coal mines. Two materials-handling activities that cause numerous injuries each year are the categories of “handling supplies or material, load and unload” and “moving power cables.” Mechanization and mine worker activity training are two methods that can aid in preventing these injuries. This paper describes three mechanical methods—the mobile manipulator, the in-mine hoist, and a cable-handling system—being developed and tested at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. Two of the devices are specifically designed for loading, unloading, and moving supplies and materials, and the third device is for handling trailing cables in the confined spaces of coal mines. Also described are safety solutions developed for underground coal mines geared to showing miners safe and unsafe ways of performing various materials-handling tasks.

By J. B. Scott, J. L. Popham, H. F. Coffer, J. J. Reynolds

This paper concerns field experiments to define the areal extent, orientation and thickness of an artificial fracture in the Sacatosa field, Maverick County, Tex. The fracture was made by a sand-oil treatment of 176,-000 gal of lease crude containing a fluid-loss additive and 270,000 lb of 20-40 mesh subangular Poteet sand. The well was perforated with a jet gun, consisting of six shots in a single plane. Fourteen test holes were drilled at various locations around the fractured well. Drill-stem tests, Micro and Sonic Logs, coring and sampling of formation cuttings were used to determine the presence of the fracture in these holes. The test holes were drilled at distances up to 250 ft in a radial pattern around the fractured well. In addition to fracture areal extent and orientation, sand grain size before and after fracturing, erosion of perforations and fracture thickness were studied. INTRODUCTION The orientation,12 areal extent3, 4 and thickness5-9 of artificially induced fractures in reservoir rock by hydraulic means have been discussed in great detail in the oil industry in recent years. Methods for initiating vertical"' and horizontal" fractures have been tested in the laboratory and the field. Although the methods used give successful well stimulation, good field data on the physical characteristics of the fracture are lacking in the literature. It is recognized generally that properties of a fracture, such as thickness, sand placement in the fracture" and shape, may vary from reservoir to reservoir. This paper gives data on size, orientation and sand placement in a large fracture initiated in a single plane in Sacatosa field, Maverick County, Tex. It is not intended as a speculative study; rather, it is restricted to actual field data on fracture properties. No attempt is made to prove that the same type of fracture occurs in all wells. The field procedure was to drill 14 test holes at various locations around the fractured well. By employing several different testing techniques, the presence of the fracture and some of its characteristics were determined. These techniques as well as the results obtained are discussed in detail in this paper. DESCRIPTION OF FRACTURE TREATMENT N. J. Chittim Well No. 37-1, completed in the San Miguel No. 1 sand, Sacatosa field, Maverick County, Tex., was chosen for the field study. The San Miguel sand is a tight, well consolidated sandstone with an average porosity of 23 per cent. The permeability ranges from 0.1 to 10 md, with a median permeability of 2.3 md. The sand thickness averages 23 ft and is located at depths of 1,150 to 1,700 ft throughout the field.I3 The fracture treatment performed on Well 37-1 was as follows. 1. The well was drilled to a depth of 1,438 ft with native mud, and 51/2-in. casing was set and cemented to the surface. 2. The casing was perforated at 1,349 ft with a fracture-initiating jet gun. This gun consists of six shots, 7/16-in. diameter in a single horizontal plane. The jets were oriented in two groups of three, 180" opposed. The perforating device was designed to initiate a fracture perpendicular to the wellbore.

By E. F. Johnson, V. O. Naumann, D. P. Bossler

A method is presented for calculating individual gas and oil or water and oil relative permeabilities from data obtained during a gas drive or a waterflood experiment performed on a linear porous body. The method has been tested and found both rapid and reliable for normal-sized core samples. INTRODUCTION Individual oil and gas or oil and water relative permeabilities are required for a number of reservoir engineering applications. Chief among these is the evaluation of oil displacement under conditions where gravitational effects are significant, such as a water drive or crestal gas injection in a steeply dipping oil reservoir. Numerous proposed methods of obtaining relative permeability data on reservoir core samples have been too tedious and time consuming for practical use, or have yielded questionable and sometimes inconsistent results. A method has been developed by which the individual relative permeability curves can be calculated from data collected during a displacement test. The method is based on sound theoretical considerations. Using this method, with a properly designed experimental procedure, relative permeability curves can be obtained using core samples of normal size (i.e., 2 to 3 in. in length and 1 to 2 in. in diameter) within a few days after receipt of the core. In a recent publication D. A. Efros1 describes an approach to the calculation of individual relative permeabilities that is based on the same theoretical considerations. We believe the approach described in the present paper is more adaptable to practical application than the method implied by Efros. In addition, comparisons with independently determined relative permeabilities are furnished to substantiate the reliability of the new method. DERIVATION Previously the theory of Buckley and Leverett as extended by Welge2 as been used to calculate the ratio of relative permeabilities. In the derivation which follows, this theory is further extended to permit calculation of the individual relative permeabilities. The theory assumes two conditions which must be achieved before the method is applicable. They are that the flow velocity be high enough to achieve what has been termed stabilized displacement,3 and that the flow velocity is constant at all cross sections of the linear porous body. In stabilized displacement the flowing pressure gradient is high compared with the capillary pressure difference between the flowing phases. The high pressure drop insures that the portion of the core in which capillary effects predominate will be compressed to a negligibly small fraction of the total pore space. The assumption of constant flow velocity at all

By Jürgen F. PH. D. Brune, Alex C. Smith, Michael A. Trevits

Underground coal mine fires in the United States continue to present a significant hazard to the safety and health of mine workers. The leading causes of mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion The National Institute for Occupational Safety and Health (NIOSH) is conducting an in-depth program of research to address mine fire prevention, early and reliable fire detection and mine fire suppression and control technologies. One segment of the research portfolio is focused on remote methods for addressing coal mine fires. This research is important because remote methods represent the primary means of fighting a mine fire when conditions are too dangerous to fight the fire directly underground. Technologies under investigation include remote methods for installing ventilation control devices (mine fire seals) and remote methods for suppressing the fire using, the injection of inert gas, gas-enhanced foam and jet engine exhaust gases into the fire zone. This paper presents a summary of remote mine firefighting technologies used in the U.S. and the results of completed NIOSH research.

In the past few years the hydraulic aspects of rotary drilling have received considerable attention. It is generally recognized that accurate prediction of circulating pressures is desirable, particularly in those areas where a delicate pressure balance is necessary to prevent both blowouts and lost circulation. For calculation purposes the standard hydraulic equations for the pipeline flow of Newtonian fluids have been altered to facilitate similar calculations for non-Newtonian or plastic fluids.'.' This latter classification includes most colloidal types of drilling muds. Two properties: plastic viscosity, un, and Bingharn yield value, Y,, are commonly used to define the flow characteristics of a plastic fluid. These are commonly obtained with multispeed viscosimeters such as the Fann V-G meter.3 Normally these measurements are obtained at some surface temperature, and are not corrected to circulating temperatures for calculation purposes. This may result in considerable error, particularly in the laminar flow calculations which comnlonly apply to the drill pipe-borehole annulus. The purpose of this study was to investigate the effect of temperature on the flow properties of some water-base muds. A laboratory model Fann V-G meter was used for measurement of viscosities, yield values and gel strengths. An aluminum water jacket with O-ring seals was machined to fit around the mud cup of the Fann meter. All mud samples were prepared by thorough mixing in a Hobart mixer. Viscosity and gel strength measurements were made with the Fann meter using standard procedures. Flow properties of muds were studied at 80, 120, 160 and 180°F. The compositions of the test samples are given in Table 1. The typical effect of temperature on the flow properties of these drilling muds is illustrated by Fig. 1. It was found that plastic viscosity and apparent viscosity decreased with an increase of temperature. However, the curves were not linear, and did not appear to follow any definite trends or patterns. Yield point data showed much more scattering.' Since a usable method for predicting drilling mud flow behavior with temperature was desired, an attempt was made to find a simple relationship between these variables. The basic approach used by Havenaars for predicting the same effect on turbulent viscosity resulted in Fig. 2, which shows that

By Larry G. Stolarczyk

[STATES REPORT Mining Research Mine Health and Safety Research for Period Ending 30 September 1980 PROGRAM Wireless MF Communication System DATE STARTED January 1980 TPO (USBM) Robert I. Chufo (PSRC) CO ( USBM) Alan G Bolton, Jr, (Mr. Patrick Neary RESEARCH AREA Industrial Type Hazards SCHEDULED COMPLETED Phase I 29 September 1980 Phase II 29 June 1981 Phase III 29 April 1982 Subject OBJECTIVE Development of demonstration Hardware. for medium frequency mine tireless communication system.]

By John M. Tinsley, Calvin D. Saunders, H. K. van Poollen

In the past few years much con-sideration has been given to the evaluation of the effect of hydraulic fracturing on the productivity of wells. Generally, these studies included the evaluation of fracturing materials, fracture extension and formation damage due to the use of various fracturing fluids. Only little consideration has been given to the characteristics, and in particular the flow capacity, of the fracture itself and its effect on well productivity. This paper presents the results of laboratory investigations pointed toward fie evaluation of the efficiency of various fracrures with special emphasis on the flow capacity of these fractures. Data presented in this paper are the results of both an electrical model study and physical testing. Under consideration are (I) effect of overflush, (2) premature production of well after treatment, (3) "tailing-in" with coarse sand near the end of the treatment, (4) effect of propping agent size and concentration, (5) reduction in effective frac-ture permeability caused by formation caused by formation fines, silt and clays, and (6) effect of various fluids on formation strength and competency. The results of this investigation indicate that the flow capacity of a fracture is affected by any or all of the various parameters mentioned above. The authors believe that a better understanding arid utilization of these factors should result in more efficient formation fracturing. INTRODUCTION Hydraulic fracturing has become almost a standard practice of many companies for stimulating production from old and new wells. Although most companies utilize this service, techniques of application vary widely between companies and areas. Probably too often when a well in an area responds favorably to a particular technique all future wells in the same area are treated in a similar manner. Possibly a modification of the technique would result in a further production increase. Variables, of which many are extremely difficult to evaluate from field results, hamper the selection of procedure changes. Attempts are being made by a number of organizations to analyze statistically treating techniques from production data. This is a very worthy and necessary approach but very possibly laboratory investigations may aid in evaluating some of the variables which tend to affect the results of a fracturing treatment. Some of the factors cannot be studied from practical field experience and only laboratory tests can show the possibilities which might exist. One of the factors which appears to be of major concern today is the flow capacity of the created fracture and how it can be changed. Papers on this general subject have been primarily concerned with the size of propping agent and the extent of fracture. Papers have also been written on the possible permeability damage to formations by fracturing fluids. In addition, it might be possible that another type of flow restriction is prevalent. This would be a restriction of flow through a sand-packed frac- ture caused by foreign materials integrating within the propping agent. This paper presents preliminary data obtained in an attempt to evaluate the effect of some factors affecting flow through sand-packed fractures. No attempt is being made to offer a fracturing technique adaptable to all areas and conditions, but to furnish data tending to show the possible effects which might be caused by variations in procedures and materials. PROPPING AGENT PERMEABLLITIES A hydraulically induced fracture containing sand as a propping agent may theoretically be classified as a packed-sand system. The flow of fluids through such packed systems has been the subject of much research. Although there have been numerous methods proposed for the evaluation of such systems, most writers agree on the general properties affecting their flow capacity or permeability. These properties include porosity, particle size, sphericity and the roughness of the particle. In some methods of evaluation . the particle size and sphericity terms are combined to produce an equation which is a function of the surface area of the particles. In this study the permeability of various fracturing sands was both measured and calculated. The apparatus for the permeability measurements consisted of a 52-in. Lucite tube with a 2.5-in. ID. A screen and drain plug were fitted in the bottom of this tube to retain and hold the sand in place while allowing fluid flow. Two pressure taps consisting of thin, highly perforated

By A. H. Heim

A method and apparatus for measuring gas porosities of rocks are described. The apparatus can be assembled from commercially available components. In principle, measurements are made by volume substitution at constant pressure. The maximum error is not more than 0.3 porosity per cent. Typical results are given. INTRODUCTION Determining the porosity of rock samples is one of the most important and yet most varied types of measurement in core analysis. Among the many techniques devised are the so-called "gas porosity" methods. An old and well known example is the Washburn-Bunting method.' The U. S. Bureau of Mines2-' described and later improved the apparatus for a now widely used method generally known as the "Boyle's law" method. In the present form of the Washburn-Bunting method,' the volume of air in the pores of a rock sample at atmospheric pressure is extracted and then collected in a graduated burette at atmospheric pressure. The volume of air is read directly as the pore volume of the sample. The absolute error in reading the collected volume of gas is independent of the total volume; thus, the relative error is larger when the volume is small, as it is for rocks of low porosity. In addition, the sample after measurement contains mercury, which limits its use for other analyses. The Bureau of Mines (or Boyle's law) method measures directly the solids volume of a sample from which the pore volume and porosity are derived, using a separate measurement of the bulk volume. Gas at a few atmospheres pressure is introduced into a sample chamber of known volume containing the rock sample. The pressure is accurately measured. Following, the gas is expanded into a burette at 1 atm, and the gas volume is read directly. From the initial pressure p, and the final pressure p2 and volume v,, the initial gas volume v1 is calculated using Boyle's law; that is, p1v1 = p2v2. Volume v, minus the volume of the empty sample chamber is the solids volume of the sample. The accuracy of the method is limited, unless corrections are made, by deviations of the gas from the "ideal" gas-law behavior assumed in the simple form of Boyle's law. The purpose of the present paper is to describe a method for measuring the gas porosity of a rock which avoids many of these difficulties. Gas volumes are measured directly with the same accuracy as the bulk volumes. Pressures of at least an order of magnitude larger than those of previous methods are employed to insure rapid penetration of the gas into the sample. While special equipment may be built to apply the method, the porosimeter may be constructed as well from commercially available components. For simplicity, the apparatus described will be referred to as the "Constant-Pressure gas porosimeter". THE CONSTANT-PRESSURE METHOD Fig. 1 shows schematically the arrangement of components comprising the present Constant-Pressure porosimeter. Briefly, the method is one of volume substitution and may be considered a null measurement. Omitting (for the present) some of the operational details, the method of measurement consists of the following three steps. 1. After evacuation, the volume of the measuring system (a ballast chamber, a manifold, two gauges and their connections) up to the sample chamber is filled with gas to a high pressure (- 1,000 psi). A sample of the gas at this pressure is trapped in one side of a sensitive differential pressure gauge to serve as the reference pressure for subsequent steps. 2. The evacuated sample chamber containing the rock sample is opened to the measuring system. As the gas expands into the chamber, the resulting decrease in pressure unbalances the differential pressure gauge. 3. The pressure is restored by means of a mercury volumetric pump. The volume of mercury injected exactly equals the free or void volume of the sample chamber (volume of empty chamber minus the solids volume of the rock within). From the injected volume and the known empty chamber volume, the solids volume is obtained and the porosity calculated. The pressure and the volume occupied by the gas are the same before and after opening the sample chamber. Expansion and compression of the gas are incidental operations and do not enter into the calculation of porosity. By the pressure balancing or nulling, the free volume of the sample chamber is merely substituted by an equal and measured volume of mercury. Since the measurements are at constant pressure, there are no compressibility corrections necessary for the sample chamber.

By G. J. Wilson

Review of difficulties experienced in drilling directional wells in the offshore Grand Isle Block 43 field showed most failures of drill pipe, drill collars and casing to have been associated with excessive dog-legs. Alleviation of difficulties was approached by synthesizing theoretical and practical concepts in a planned dog-leg control program. Preventive measures necessary to control dog-leg severity and corrective measures used to reduce unacceptable doglegs are discussed. When other measures fail, deliberative measures as outlined can be employed after the probable cumulative fatigue damage to be sustained by the drill pipe has been determined. Results of a program successful in virtually eliminating problems stemming from excessive dog-legs indicate that control of dog-leg severity in directional wells is feasible and will cause no decrease in the over-all drilling rate. INTRODUCTION Prompted by an increasing frequency of drill pipe, drill collar and casing failures, a study of 50 directional wells representing 592,000 ft of hole, including 444,000 ft of deviated hole, drilled in the offshore Grand Isle Block 43 field was conducted in early 1965. A number of drill pipe washouts and six keyseating problems were recorded and a detailed review was made of 16 failures which had required fishing effort in 10 of the 50 directional wells drilled prior to June, 1965. These problem wells are exemplified by Wells G and F for which pertinent data are shown in Figs. 1 and 2. Data pertaining to all of the 16 failures are summarized in Table 1. Inspection of these data shows most of the problems to have been associated with dog-legs in excess of theoretical limits suggested by Lubinski' and excessive dog-legging is indicated to have been concomitant with whipstocking in several of the problem wells. Results of the investigation agreed with those reported by Schenck2 who had concluded that problems could be expected when dog-leg severity exceeded limits proposed by Lubinski. Since Schenck had demonstrated the desirability and feasibility of drilling directional wells without excessive dog-legging, a dog-leg control program was established in June, 1965 for wells drilled in the Grand Isle Block 43 field. This paper reviews the methods by which theoretical and practical concepts were synthesized to develop a program of preventive, corrective and deliberative measures which virtually eliminated problems stemming from excessive dog-legs in directional wells. Dog-legs of a magnitude causing no damage are referred to as permissible +1CONTINENTAL OIL CO. HARVEY, LA.

By H. D. Outmans

The author applies the theory of hydrodynamic stability to fluid flow in porous media and concludes that the displacement of miscible liquids is stable if the stability coefficient, as defined by Eq. 19.2 or Eq. 27.0, is positive. The conclusion is invalid, however, since it is based on a faulty argument. To demonstrate this, the reader is referred to Eqs. 4.1 through 4.5 of the paper which describe, in differential form, the first-order disturbances c, u, v, w and p. In these same equations, cx, cz, gl, g3 and are functions of the stable concentration c. This concentration c is known and depends on x, z and t (the author assumes cy = 0). It follows that cx, cz, gl, g3 and µ are also functions of x, z and t. With this in mind, we turn to Eqs. 8.1 through 8.5 which were derived from Eqs. 4.1 through 4.5 by substituting Eq. 6.0. The significance of this substitution is that the author thereby limits the solutions of Eqs. 4.1 through 4.5 to equations of the form of Eq. 6.0. Eqs. 8.1 through 8.5 represent an infinite linear system with five unknowns: c, u, v, w and p. The coefficients cx, cz, gl, g3 and µ in this system are known at each point and at each instant; the coefficients containing derivatives of f are unknown. If this infinite linear system in c, u, v, w and p is to have a nontrivial solution, then it is indeed necessary (as the author states) that the determinant of the coefficient matrix of Eqs. 8.1 through 8.5, i.e., ( A 1, be equal to zero. This condition, however, is not sufficient. A non-trivial solution exists if, and only if, the rank of the coefficient matrix of the entire infinite system is smaller than five. In other words. all minors of order five must vanish and only if all the coefficients in Eqs. 8.1 through 8.5 are constant is this equivalent to the condition |A| =0. Constant coefficients means that gl, g3 and µ, for instance, are constant; and, since they depend on c it follows that c must be constant. We conclude that the condition I A I = 0, on which the author bases his calculations, is necessary and sufficient for a nontrivial solution only if the concentration c is constant. In other words, the author does not investigate the stability of a miscible displacement but, rather, only the stability of the flow of a homogeneous liquid. Using the initial condition and the fact that the coefficients are constant, we find

By A. J. Hudson, M. R. Yenchek

Faulty insulators on mine trolley/track haulageways may allow the flow of leakage currents into the mine roof and ultimately result in combustion of the local roof material. The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), has devised a passive means to detect overheating insulators on direct current systems. The detector consists of a spring-loaded cartridge that ejects a reflective streamer of white Teflon tape when subjected to elevated temperatures. The cartridge assembly can be easily installed over the outer metallic shell of an existing trolley line insulator. If an insulator overheats due to ground leakage currents, the visible streamer alerts mine personnel traveling on the haulageway.

By A. M. Skov, L. F. Elkins

First response to large-scale water flooding in the fractured very low permeability Spraberry sand has led to a new unique cyclic operation. Capacity water injection is used to restore reservoir pressure. This is followed by marly months production without water irzjection and the cycle repeated. Expansion of the oil, rock and water during pressure decline expels part of the fluids but capillary forces hold much of the injected water in the rock. At least with reservoir pressure restored and with partial water flood development, field performance has proved this cyclic operation is capable of producing oil from the nzatrix rock at least 50 per cent faster and with lower water percentage than is imbibition of water at stable reservoir pressure. INTRODUCTION The Spraberry Field of West Texas presents unusual problems for both primary production and water flooding. Extensive interconnected vertical fractures in the fractional-md sandstone permitted recovery of oil on 160-acre well spacing, but they made capillary end effects dominant. Primary recovery by solution gas drive is less than 10 per cent of oil in place. The concept of displacement of oil from the sand matrix by capillary irnbibition of water has led to field techniques which promise greatly increased oil recovery. Free exchange of laboratory research, reservoir information and results of field pilot tests among the various companies has been very important in development of this technology. Five units covering a total of 170,000 acres have been formed for water flooding, and 10 other areas covering an additional 175,500 acres are in various stages of unitization. Part of the Driver Unit reaching fillup first has demonstrated very unusual waterflood behavior and indicated numerous operating problems that will develop within and among the various units. SPRABERRY ROCK AND PRIMARY PERFORMANCE The Spraberry, discovered in February, 1949, is a 1,000-ft section of sandstones, shales and limestones with two main oil productive members: a 10-15 ft sand near the top and a 10-15 ft sand near the base. In part of the field some thinner intermediate sands are oil productive, and others are water bearing. All sands have permeabilities of 1 md or less and porosities of 8-15 per cent. Ordinary core analysis and electric and radiation logs are ineffective in differentiating between oil productive and nonprcductive sands. Sands capable of containing producible oil are best identified by mercury injection capillary pressure measurement and, in some cases, by core water saturation. About 3,500 wells have been drilled in the 500,000-acre trend. Vertical fractures were observed in practically all Spraberry cores. Continuity and interconnection of fractures were confirmed by pressure interference among wells during early development.' Major fractures trend northeast-southwest as indicated by oriented cores and confirmed by five fluid injection tests, by analysis of the pressure transients observed during development,''' and by three interference tests in the Driver Unit Water Flood reported herein. Fracture spac- ing probably averages inches to a few feet. Spraberry wells typically produced 100-400 BOPD initially after hydrauLic fracture treatments. By 1962 oil production had declined to an average of 12 bbl/well/day, near the economic Limits of operation. Reservoir pressure had declined from 2,300 psi initially in the Upper Spraberry and 2,500 psi in the Lower Spraberry to 500-1,000 psi. Partial closing of the fractures with declining reservoir pressure is believed to be the cause of such low oil production rates at these relatively high reservoir pressures. Cumulative recovery of 208 million bbl of oil is 80 to 90 per cent of that recoverable by primary means. Performance of the entire reservoir is summarized in Fig. 1. IMBIBITION WATER FLOODING By 1952 reservoir performance indicated low primary recoveries. Most engineers, expecting serious channeling of injected fluids through the fractures, held little hope for secondary recovery. With its extensive background of research on the fundamentals of fluid flow within reservoir rocks, Atlantic's Research and Development Division on short notice in 1952 conceived that displacement of oil by capillary imbibition of water into the rock might significantly increase Spraberry recovery. Laboratory data reported by Brownscombe and Dyes scaled to probable reservoir conditions showed potential waterflood recovery equal to or greater than primary recovery with a 10-15 year flood life.= A pilot test using three 40-acre injection wells, one central producing well and 18 surrounding observation wells demonstrated technical feasibility of the process. Injection of 1.5 million bbl of water from November 1952 to August 1955 proved water entered the rock and displaced oil

By W. R. Phibbs

The blast furnace of the Columbia Steel Corpn., at Ironton, Utah, was put in blast April 30, 1024, and its operation has presented some interesting problems. The coke for the furnace is furnished by 33 Koppers Becker type ovens of 15 tons capacity each. The coal is shipped from the company's mine at Columbia, Utah, which is approximately 123 miles from Ironton, and is probably the highest volatile coal that is being coked for blast furnace use in this country. The analysis of the coal is: PeR Cent. Moisture................................................. 3.90 Volatile.................................................. 39.00 Fixed carbon............................................ 51.10 Ash............................................... 6.00 Sulfur................................................. 1.07 The analysis of the coke is: PeR Cent. Volatile.................................................. 0.55 Fixed carbon............................................. 89.70 Ash...................................................... 9.75 Sulfur................................................... 1.05 The coke is light and of a fingery construction, but is very fast burning. A screen test of the coke as loaded into the skip tubs at the furnace shows the following: Per Cent. On 2 in.................................................. 17.90 On 11/2 in................................................ 41.78 On 1 in.................................................. 27.80 Through 1 in............................................. 12.52 The by-product yields are as follows: Gas................................. 11,000 cu. ft. per ton of coal Sulfate............................... 30 Ib. per ton of coal Tar.................................. 12.65 gal. per ton of coal Motor fuel........................... 3.00 gal. per ton of coal Average B. t. u. in gas................. 567