Search Documents

By P. Hazebroek, C. S. Mathews, E. E. Allen, H. C. Lefkovits

A rigorous study was made of the behavior of reservoirs composed of horizontal layers, unconnected except at the well and filled with a compressible fluid. The report is presented in two parts. Part I deals with the practical implications of the results obtained; Part 11 contains the mathematical derivation of the solution. The main portion of Part I is concerned with application of the results to reservoirs composed of two layers. Relative rates of depletion of the layers are studied, and it is shown that differential depletion between layers exists in the transient stage of the reservoir, which generally is of an order of magnitude longer than the transient stage in a single-layer reservoir. In the transient stage, the more permeable layer is depleted faster than the less permeable. However, the reservoir approaches a steady-state situation where both layers contribute equally to production. Theoretical build-up curves from such reservoirs are presented, and the influence of a skin effect and flow into casing and tubing are also evaluated. The build-up curves are predicted to have, first, the familiar logarithmic straight-line section and, subsequently, a rising and flattened section. The results found are compared with an extension of an approximate theory, and it is found that this simplified theory is applicable over most of the life of the reservoir. Extensions to reservoirs containing more than two layers are indicated, and examples of the performance and build-up curves for three-layered reservoirs are presented. The theoretical results on build-up curves were applied to field examples of such reservoirs, and satisfactory results were obtained. From the build-up curve, the pemeability-thickness product, the wellbore damage and the static pressure are obtained. However, it apparently is not possible to determine the properties of the individual layers from the combined build-up curve. A large number of reservoirs have been found where the producing formation is composed of two or more layers of differing physical characteristics, such as permeability and porosity, and where also the thicknesses of the layers differ. Since in general a differential depletion should exist between the layers of such reservoirs, it would be advantageous to know the amount of the differential depletion under a given production history. It also would be valuable to know the pressure behavior, because it could be undesirable to produce a reservoir in such a manner that the pressure in one of the layers would have fallen below the bubble point of the oil at a time when another layer might still be virtually undepleted. The determination of static pressures in shut-in wells with slow build-up is another feature of importance in layered reservoirs. If the behavior of the reservoir differs appreciably from the predicted behavior of a single-layer reservoir, the type of analysis for build-up curves suggested for single-layer reservoirs is not applicable. Several authors have treated the problem of finding the pressure and production characteristics of multilayer reservoirs. Horner treated the problem of n layers in an infinite field, the layers being connected only at the well. Tempelaar-Lietz2 has presented an approximate treatment of the characteristics of a bounded reservoir composed of two layers of different permeabilities and equal thicknesses. Homer gave no information on differential depletion between layers, and the treatment of Tempelaar-Lietz was not applicable for prediction of pressure build-up behavior. In addition, it was thought that a more rigorous treatment than the one by Tempelaar-Lietz would be valuable in determining the range of validity of this solution. The present study, therefore, was made of a bounded reservoir composed of two or more layers,

By P. K. Parhi

The extraction of nickel has been carried out by the hollow fiber membrane technique using D2EHPA as the mobile carrier from the manganese nodule leach liquor after separation of Cu(II), Zn(II) and Co(II). The experiments were designed according to central composite design (CCD), which is a response surface methodology. The process parameters used for the experimental design were: pH, concentration of D2EHPA in the membrane phase, flow rate and H2SO4 concentration in the strip solution. Based on the analysis of variance, a reduced quadratic model was found to best fit the experimental data. The process parameters were optimized to maximize the nickel flux and the optimized conditions were flow rate: 630 mL/min; pH: 6.37; D2EHPA: 1.15 mol/L (1,150 mol/m3) and H2SO4: 2.39% (430.2 mol/m3), for a maximum nickel flux of 7.08 x 10-5 mol/m2.s, which was in good agreement with the actual Ni flux of 6.99 x 10-5 mol/m2.s.

By E. R. Spencer, E. R. Bauer

Previous studies and research efforts have shown that noise-induced hearing loss (NIHL) is a problem in the U.S. mining industry. In response, researchers at the National Institute for Occupational Safety and Health (NIOSH) have been conducting a cross-sectional survey of equip­ment noise and worker noise exposures in the mining industry to estimate the potential for NIHL within the mining community. One commodity recently surveyed was the extraction of sand and gravel from surface pits and by dredging. To address the potential for NIHL in the sand and gravel industry, sound levels on and around the dredges and processing equipment were recorded to iden­tify areas of high noise levels. Full-shift worker dosimetry, in conjunction with task observations, was documented to determine the relationship between exposure and source. This paper presents research examining noise on dredges used in several surface mine sand and gravel operations and in the processing facilities. Results indicate that there are areas on the dredges (crane, suction pumps and diesel engines) where sound levels greater than 90 dB(A) are pres­ent. In addition, crushers and screens used in the processing of the sand and gravel also generate sound levels greater than 90 dB(A). Although no surveyed worker exceeded the Mine Safety and Health Administration’s (MSHA’s) permissible exposure level (PEL) of 90 dB(A) eight-hour time-weighted average (TWA8), laborers, mechanics, oilers, helpers, pickers and greasers are the workers most likely to be exposed to hazardous sound levels and to thus develop NIHL over time

By Motohisa Kanda

The time and amplitude statistics necessary to adequately describe electromagnetic (EM) noise in mines are illustrated through computer software techniques. They are 1) Allan Variance Analyses (AVA), 2) Interpulse Spacing Distributions (ISD), 3) Pulse Duration Distributions (PDD), 4) Average Crossing Rates (ACR) , and 5) Amplitude Probability Distributions (APD) . These statistics are illustrated using data taken from a rather large store of raw analog data recorded in operational mines. The curves generated for the illustrations characterize the noise environment in the mines from which the corresponding data were taken, and should aid in the design of reliable communication systems for such mines.

By H. H. Rachford, J. Douglas, D. W. Peaceman

A numerical solution of equations describing two-phase flow in porous media shows promise in providing a technique for predicting the displacermet from satlds of oil by water or gas. The description includes the influence of relative permeability, fluid viscosities and densities, graviry, and capillary pressure, and, tholrgh tested ortly for two-dimensional cases, should be eqlmlly applicable in three-dimensional geometry. Two memorical methods ore presented: the first method is quite general in its applicability; the second method can be used only with certain types of boundary conditions but requires less computing. Comparisons of computed results with data from Inhoratory models are presented. These data were taken on a water flood of a strarified model and on water floods of a five-spot model for favorable and unfavorable mobility ratios. On the stratified model, excellent agreement with recovery at breakthrough was obtained; agreement with recovery after breakthrough was poor. In the five-spot model, good agreement was obtainecl with recovery at and after breakthrough. The purpose of this paper is twofold: first, to present a reservoir engineering method requiring knowledge only of rock geometry and the normally measured rock and fluid properties for calculating the multi-dimensional flow of water displacing oil from porous, water-wet rock containing connate water; and, second, to investigate the validity of the method by comparing results of calculations with previously observed displacements in laboratory models. The availability of such a verified technique of reservoir analysis would afford major advantages. First, it would demonstrate that the fundamental macroscopic concepts of two-phase fluid mechanics, i.e., relative permeability and capillary pressure, yield an adequate description of the physical process. Also, since most reservoir rocks appear to be water-wet and contain connate water along with oil, it would provide a method of technical and economic value for calculating the course of oil displacement by water directly from measured reservoir and fluid properties. It is important to emphasize that the calculation is subject only to the limitations of detail and precision of reservoir information, but not to limitations introduced by simplifying assumptions. Further, it would providc almost the only means of examining the influence of factors such as the size and extent of reservoir inhomogeneities and uncertainties in the basic reservoir data. Knowledge of this influence is essential in stating quantitatively the detail required to define a reservoir and in establishing the relation between the uncertainty in the definition of reservoir properties and the reliability of predicted performance. Moreover, in the process of solving a particular problem much detailed information would become available about the displacement process. For example, at each point in the reservoir for all stages of the displace ment. the calculations would yield not only the water and oil saturations but also the direction and magnitude of fluid velocities and the local fluid mobilities. Such dctail is potentially of great value in giving insight into the mechanics of particular displacements. The development of such a method has long been the goal of research in the application of numerical an-alysis to petroleum reservoir enginecrinz. The most complete treatment of the displacement process published to date is that of Douglas. Blair, and Wagner,' which, however, was limited to flow in a single dimension. The method presented in the present work is hascd on the numerical solution of a finite difference analogue of the multi-dimensional differential system describing the displacement process. Although current work has considered only displacement of oil by water from water-wet sands, the differential system for other immiscible displacements, such as gas displacing oil with which it is in phase equilibrium, is quite similar. It should therefore be expected that the technique described will be applicable to displacement by gas as well. The description of the simultaneous flow of fluids through porous media in terms of relative perrncability and capillary pressure has been adequately discussed in the literature and standard textbooks. Sec, for exampje, Muskat. Chapter VII.'

By Frank Firmstone

By Steve Skelhorn

Over the recent years, major advances have been made in design of precast concrete segmental tunnel liner. Starting from basic, parallel sided rings, we now have state of the art, universal rings incorporating custom tapers to suit individual requirements. At planning stage, the ring diameter is normally fixed and the ring geometry is one of the first items to be assessed. Obvious factors such as TBM layout and curve radius can constrain geometry; however, there others factors that should be considered in order to optimize production. This paper takes a look at the history of the segmental rings and criteria for ring selection, including: general ring geometry;; individual segment geometry; ring taper, and ring width. This paper also explores optimization of ring with a focus on constructability.

By Tom Szaraz

Part of a major sewer expansion for the City of Columbus, Ohio. The Big Walnut Outfall Augmentation Sewer?Part II (BWOAS) consists of 13,200 feet of tunnel of 12-foot tunnel passing mainly through glacial deposits with a water head of up to 2 bar. A Lovat RME167SE was used to drive this tunnel with steel fiber reinforced precast segmental liner used for support. This paper will discuss the concepts for tunnel sup-port and TBM selection, the problems encountered with the TBM sealing systems and the solutions used to repair the machine.

By P. E. Baker

A paper by A. S. Odeh' expounds a capillary-flow theory which purportedly provides a mechanism whereby relative permeability depends on oil-water viscosity ratio and may be greater than unity for high viscosity ratios. Core-measurement results are presented to support the theoretical development. This paper presents arguments to indicate that (1) the theoretical treatment is basically incorrect, (2) data reported are insufficient to support the conclusions and (3) literature cited does not support the theory or the conclusions. PROPOSED MECHANISM The essence of Odeh's theory is that oil flows as a filament along the central portion of a straight, uniform capillary of radius r filling the tube to a radius ri. Surrounding the filament of oil is an annulus of water in which exists vortex motion but no net flow. The water is described as being in "microscopic but not macroscopic" motion. The oil filament is aided in its flow by moving upon the water vortexes as if on roller bearings. This process is presented as a steady-state flow condition. The first objection to the existence of vortexes in the presumed water layer is that the theory provides no mechanism whereby they can be established. This fact was mentioned by C. F. Weinaug in a discussion published with Odeh's paper. The capillary contains no irregularities or obstructions, and the water is not presumed to be in turbulent flow. Apparently, cylindrical symmetry is assumed; therefore, the supposed vortexes must be toroidal, the line of zero velocity being a circle concentric with and in a plane perpendicular to the axis of the capillary. This is a rather difficult picture to accept. The author referred to Yuster's statement' that he had observed the "spinning in place" of otherwise immobile water. Yuster's article does not describe the conditions under which this motion was observed or the means used to observe it. However, the article does make clear that the observed motion was not in a straight, uniform capillary but, rather, apparently oc-cured in some kind of dead-ended pore space. Obvious- ly, such a report cannot be considered as support for Odeh's concept of two-phase capillary flow.

By Jan Steinhoff

The design options of a gravity separator are still limited and rely on the study of settling behavior. A methodology will be presented where an experimentally given inlet droplet size distribution (DSD) is the basis for the calculation of the dispersion layer in a gravity separator. A pilot-scale continuous gravity separator is presented and CFD (computational fluid dynamic) results are validated. A transmitted light measurement technique for the determination of the DSD is presented up to a holdup of 15% dispersed phase. The resulting DSD was in the range of 20–2000 μm depending on flow rate and phase ratio. Furthermore, correlations of the real DSD with the settling behavior of the dispersion in a settling cell are discussed. The new approach to the description of gravity separators will be presented and the applied CFD methods showed good results with the system water/paraffin.

By Sean Gallagher, Thomas G. Bobick

The Bureau of Mines performed a pilot study examining the effects of posture on back strength and Maximum Acceptable Weight of Lift (MAWL) on six healthy male subjects (M = 32 years + 4 SD). Six hack strength measurements (3 static and 3 dynamic) were made while the subjects were kneeling and standing. In addition, these subjects (who were unaccustomed to lifting in these postures) volunteered to participate in a study of psychophysically determined NAWL in both postures. Results of the back strength tests showed a significantly lower peak torque per body weight output in kneeling versus standing hack strength measurements for five out of six test comparisons (p < .05). Subjective estimates of lifting capacity in the kneeling posture were significantly lower than those for the stooped posture (p < .05). The results of tests of hack strength and lifting capacity in these two postures provide useful information to consider in determining the physiological and psychophysical stresses imposed by these

By Zhigan Deng

Cooling crystallization was used to separate iron (III) and nickel (II) from acidic sulfate solution produced by leaching of molybdenum-nickel black shale. The effect of K2SO4 concentration, crystallization temperature, solution pH and crystallization time on recovery of nickel (II) and precipitation of iron (III) was investigated, in order to obtain effective separation of nickel and iron. The optimum parameters determined were as follows: 200 g/L K2SO4, 10 °C crystallization temperature, solution pH of 0.5 and 24 h crystallization. Under these conditions, 97.6% nickel (II) was recovered as K2Ni(SO4)2, 6H2O crystals and only 2.0% of the total iron (III) was precipitated. Recrystallization yielded K2Ni(SO4)2, 6H2O crystals with a purity of 98.4%.

By S. J. Page, J. A. Organiscak

Airborne respirable dust surveys were conducted at six surface coal mines to investigate the effectiveness of dust control methods used on rotary rock drills and bulldozers. Dust controls commonly used on drills include a dry dust collection system, exhausting from a shrouded area around the collared hole, and an enclosed drill operator cab, filtering airborne dust from the cab. Bulldozers are also typically equipped with an enclosed operator cab as a dust control measure. Airborne respirable dust sampling was conducted near each equipment&apos;s source of generation and inside its enclosed cab. Silica analysis was performed on the dust samples to determine the percent silica content in the dust generated at the six mining operations. An additional eight- month follow-up of dust sampling was also conducted in the enclosed operator cabs of several rock drills and bulldozers. Data were analyzed for long-term variability of accepted control methods to abate dust and silica levels. The highwall rock drill was the major and most variable dust source as compared to the bulldozer, generating dust levels, on average, one order of magnitude higher than dust levels of the bulldozer. Four of the six drills surveyed had dust containment and capture problems at the shrouded drill table above the lple. Repairs or modifications to three of the drill dust collection systems were shown to reduce dust levels by more that 50% next to the shrouded drill table. The enclosed operator cabs provided more than 90% and more than 40% lower dust levels than at the dust source for the drill and bulldozer, respectively. Long-term sampling of several of these highwall drills and bulldozers showed that the dust levels in the drill cabs were frequently higher than 0.2 mg/m3 and more variable than in the bulldozers. The bulldozer dust levels were frequently below 0.2 mg/m). Future research should focus on improving some of the deficiencies present in the drill&apos;s primary dust collection system, and developing quality control methods to ensure the integrity of enclosed cab protection for equipment operators.

By Brian G. White

The Coeur d&apos;Alene Mining District of northern Idaho is remarkable for its number of large ore bodies and for the amount of its historical production of lead, zinc and silver (Fig. 1). Since veins were first discovered in 1884, more than 127 Mt (140 million st) of ore have been produced from narrow, high-grade veins. Mining continues at the Lucky Friday, Galena and Sunshine mines (Fig. 2). All have been in production for decades. At these mines, more efficient mining and exploration techniques have reduced costs while adding significant new reserves. Even the old Bunker Hill Mine, where ore was first found in 1875, continues operation on a limited basis, partly involving production of world-class pyromorphite specimens. Until recently, the Coeur Mine was also a profitable silver producer. Other large producers have included the Star-Morning, Hecla, Page, Standard-Mammoth, Hercules and Gold Hunter mines (Fig. 2). The first deposits were discovered by prospectors who spilled over from the Murray gold mining district, 24 km (15 miles) to the north. The Bunker Hill Mine was founded the year after the first veins were discovered. Bunker Hill has now operated for more than 100 years. Production includes 2.3 Mt (2.6 million st) of lead, 1.1 Mt (1.2 million st) of zinc and 4.1 kt (132 million oz) of silver. Total district production through 1996 (Springer, 1997) amounted to 7.3 Mt (8.1 million st) of lead, 3 Mt (3.3 million st) of zinc, and 34.5 kt (1.109 billion oz) of silver. This record establishes the district as the largest recorded producer of silver in the world, while also yielding major quantities of lead and zinc. Only Potosi, Bolivia, may have produced more silver, although records are unclear. Despite the district&apos;s longevity, historic production and current activity, the published literature on the district lags behind with regard to recent concepts of district geology. The most recent comprehensive US Geological Survey (USGS) bulletins (Hobbs et al., 1965; Fryklund, 1964) are dated. Much research in the last half century has been short-lived or geographically restricted because the district is large and its geology is complex - and even this research tends to remain unpublished. Thus, it has been difficult for in- [ ]

By Cary Hirner

The Metropolitan Water Reclamation District of Greater Chicago (District) is in the final phase of completing the Calumet System component of the Tunnel and Reservoir Plan (TARP) by bringing the Thornton Composite Reservoir online by 2014. The Thornton Composite Reservoir will provide nearly 30 billion liters (7.9 billion gallons) of additional storage for minimization of combined sewer overflows(CSO) and flooding in the Chicago metropolitan area. The project requires that the existing 6.7 m (22 ft) diameter Thorn Creek tunnel conveying overbank flood flows is re-routed and connected to the Thornton Composite Reservoir. This paper presents the components of the Thornton Composite Reservoir and specifically the detailed evaluation of a drill-blast tunnel. Other project features include an access shaft, control gate, energy dissipating structure, bulkheads, and live tunnel connection. The construction contract will be procured in late 2009.

By J. Chilton

The fact that methane ignitions continue to occur at the mining face indicates that monitoring with machine-mounted methanometers does not always indicate the presence of high methane concentrations. Methane concentrations at the face change quickly due to changes in airflow. By measuring these changes in airflow, it may be possible to predict changes in face methane levels more quickly. Currently there are no techniques or instruments to accurately measure airflow in by the mouth of the ventilation curtain or tubing. Tests conducted in the NIOSH ventilation test gallery compare the data provided by one-, two-, and three-axis ultrasonic anemometers. The effects of changes in airflow direction and turbulence on instrument readings are discussed, and guidelines are given for selecting the type of instruments to be used for monitoring airflow near the mining face.

By Larry G. Stolarczyk

1.0 FRAMEWORK FOR COMPARISON This document describes the decision factors that bear on the selection of the modulation process for the wireless underground medium frequency (MF) communication system. The selected modulation process must satisfy the Bureau of Mines stated objective of improving general communications within an underground mine. The improvement being sought includes the development of a wireless communication technology of measurable benefit to both mine safety and mine productivity. The improvement will allow wireless communications paths to exist between roving miners. The wireless communication paths will also be made compatible with the existing underground telephone system to extend paging and voice communication throughout the underground mine. The new wireless equipment will include man-pack, vehicular, repeater, and base station transceivers. Repeaters and base stations will feature coupling networks for interfacing with the existing telephone circuits. Frequency modulation (FM) and single sideband (SSB) modulation processes are analyzed in view of the special conditions associated with underground mining. Of primary importance is the tremendous electrical noise generated in an operating mine that could adversely affect communications quality. High noise coupled with high attenuation rate of near field signals forces the communication system to be inherently short range. Fortunately, near field signals can propagate over great distances on underground wires and cables. The framework for comparison is generated by presenting all factors that

By D. O. Wyble

Five water-driver fields, for which pressure predictions had been made within a few years after discovery, were re-studied when four to five years of additional pressure and production data became available. It was fortnd that forecasts of the pressure in water-dri~fe reservoirs may be subject to considerable unccrtainty. Predictions car be erroneous when there is insufficient presswe history to define the cllaracteristics of the aquifer, and when there are errors in the pressure, production or geologic data. INTRODUCTION The efficient operation of an oil or gas reservoir requires that the important characteristics of the reservoir be determined soon after its discovery. It is especially desirable to evaluate the pressure-production relationship quickly, for this relationship provides a basis for deducing the type of production mechanism that is operative, and for making pressure predictions. The pressure predictions, in turn, provide a basis for calculating efficient rates of production, determining whether water or gas should be injected, etc. The importance of pressure prediction is such that forecasts should be made as accurate as possible, and the limits of error well defined. Historically, pressure forecasts for some fields have proved very accurate, while for others the forecasts were so erroneous that they resulted in the adoption of wrong, or at best, unnecessary production practices. Pressure predictions made for water-drive fields are especially subject to error. Accurate forecasting for these fields requires that much be known not only about the reservoir proper but about the adjacent water-filled rock as well. The water-containing rock, or aquifer, may extend for many miles, and often there is only meager data regarding its thickness, permeability and porosity. Much of the information must be inferred from the previous pressure behavior of the reservoir. A brief pressure history may provide little information about the characteristics of the aquifer. Hence, pressure predictions made early in the life of water-drive fields can be incorrect. The work described in this paper was done to determine the degree of reliability which can be expected of pressure predictions made within a few years after water-drive fields are discovered. Five fields, for which the original pressure predictions had been based on less than seven years&apos; history, were re-examined with the aid of four to five years of additional pressure data. Where the predictions were inaccurate, the reasons for failure were ascertained. The studies were accomplished by use of the electric reservoir analyzer.&apos; The analyzer was first adjusted to repeat the original pressure-production match using the same values for the various parameters as were used in the original study. Then, the actual production rates experienced during the time elapsed since the initial study were set into the analyzer, and the pressure behavior indicated by the machine for this period was compared with that which actually OCcurred. Where the pressure profile traced out by the analyzer deviated from the observed field behavior, the analyzer was readjusted to obtain a better over-all match. The old and the new solutions were compared to determine the reasons for any differences. COMPARISON OF PREDICTED RESERVOIR PRESSURE BEHAVIOR WITH ACTUAL PERFORMANCE Field A The original pressure-production match is entirely adequate as evidenced by the pressure match of the field&apos;s history subsequent to Jan., 1952 (see Fig. 1)&apos;.