Search Documents

By Anastasia Alksnis

Pyrrhotite is an iron deficient, low nickel content sulfide mineral that is commonly associated with pentlandite, a nickel-rich sulfide; and are both main components of the nickel ore mined in Sudbury. Pyrrhotite tailings generated in the concentration of Ni ores are stored in tailing reservoirs and presents serious environmental risks including acid mine drainage. This study investigated the potential of converting pyrrhotite into a valuable resource through the use of fluidized bed roasting, in which the mineral will be oxidized to produce iron oxide and SO2 gas. These products can then be used to create iron for high-grade steel and elemental sulfur. Thermogravimetric analysis of Sudbury pyrrhotite was performed to study the oxidation kinetics, supporting the feasibility of this process. Further, energy and materials balance was carried out to establish the basic parameters of a possible roasting process.

By Richard E. Ray, George N. Aul, Fred Garcia, William P. Diamond

Increasing longwall panel dimensions, particularly face width in gassy coalbeds, may result in unexpected increases in methane emissions. To investigate this problem, continuous longwall face emission monitoring studies were conducted at two adjacent mines operating in the Pocahontas No. 3 Coalbed, where longwall faces were to be extended from 229 to 305 m (750 to 1,000 ft). It was predicted by regression analysis of methane emissions data from 229 m (750 ft) wide longwall faces that extending faces to 305 m (1,000 ft) would increase methane emission rates by only 7 percent (0.6 m3/min (20 cfm)), to 8.6 m3/min (304 cfm) at the VP-1 Mine. In contrast, it was predicted that extending faces at the VP-3 Mine could increase methane emissions by as much as 13 percent (1.8 m3/min (65 cfm)) to 16.1 m3/min (567 cfm). The geologic and mine design factors influencing the variation in face emissions between the two mines will be discussed.

By Sean Gallagher, Christopher A. Hamrick, Arnold C. Love

Twelve subjects participated in an investigation of the biomechanical stresses of asymmetric lifting in stooped and kneeling postures. Three factors were manipulated in this study: Posture (stooped or kneeling), height of lift (35 or 70 cm), and weight of lift (15, 20, or 25 kg). Subjects were required to lift or lower a box every 10 seconds for a period of 2 minutes. Electromyography (PIG) of eight trunk muscles was collected during a lift in this period. The PIG data, normalized to maximum extension and flexion exertions in each posture, were input to a biomechanical model and used to predict compression and shear forces at the L, level of the lumbar spine. Results from the EMG-driven biomechanical model indicated that compression was greater when lifting to a higher shelf (p < 0.001), and indicated a significant interaction between posture and the weight of the lifting box (p < 0.01). Peak lateral shear was not significantly affected by any main effects or interactions (p < 0.05). Anterior shear was increased with increasing height of lift (p < 0.001), and also by the posture x weight interaction (p c 0.01). A multivariate analysis of variance (MANOVA) indicated a complex relationship for recruitment of the eight trunk muscles, with the triple interaction being significant (p < 0.001). The results of this investigation will be used to evaluate safe loads for lifting in these restricted postures.

By Henry Wurtz

Observing in the Engineering and Mining Journal, of January 16th, 1875, page 35, a report of a brief discussion upon the nature and origin .of this unique and interesting coal, I take the liberty— on thus finding it a subject of interest to members of the Institute, and especially as my name came into this discussion—to cornmunicate some results which may serve at least to overthrow certain erroneous ideas that have prevailed. While I would not claim to -have made much approach to an understanding of this mineral—the whole of what I call Apozoic Mineralogy being as yet dark and almost unknown ground—yet I believe I have shown that few minerals of such importance and abundance, and so long before the world, have been so singularly misunderstood. On first examination of a sample of the substance to which the name of carbonite has been given, my surprise was not small, at failing to recognize in it one individual characteristic of true coke; neither the hardness, lustre, color, streak, porosity, sonorosity, structure, fracture, nor any of the so-called "pyrognostic" characters. Indeed, comparison with any coke, or variety or modification thereof, seemed altogether fantastic. Therefore the controversy regarding supposed trap dykes, whose existence at the locality is denied by some, seems useless, as we have no question of a natural coking, there having been no coking at all.

By P. H. Dudley

I have taken the liberty of calling the researches herein mentioned industrial, to distinguish them from those strictly scientific, where every known appliance is used to insure accuracy in determining principles. The industrial researches are made to ascertain wherein we have failed to embody, in practice, the principles which have been fully demonstrated by the more purely scientific investigations. So far the researches have been mostly confined to the conditions of combustion as used in locomotive furnaces, although we have examined, to some extent, furnaces under marine and stationary boilers. The products of complete combustion are gases, and, knowing what we should have, it is at once shown by analyzing the products whether the desired reactions are taking place. In spite of imperfect furnaces, lack of system in the arrangement of grate-bars and exhaust nozzles, the results are not altogether vitiated, because the analyses are not closer than one-tenth of one per cent., as under the present conditions it is hardly possible to collect gas exactly under the same conditions at different times. All of &apos;our industrial operations have developed in the past few years so rapidly, nearly all of them paying, that,, until within the past three years, comparatively little attention has been given to their economy outside of the profession. Great corporations have not asked and considered the question in earnest, can we utilize our heat so as to produce the same effect at less cost? The applications of heat are so extensive, entering into every branch of industry, the principal power used to carry on metallurgical processes, to conduct transportation, that its econonlical generation becomes of universal importance; in fact, its economical generation and application is the leading industrial question of the day. It is stated by those who have given the subject much attention, that in our best steam-engines not over 10 per cent of the theoretical value of the fuel is utilized, and upon locomotives it is far less, probably not exceeding under the most favorable circumstances 5 or 6 per cent. In recent experiments made with the dynagraph, in drawing trains upon the Lake Shore and Michigan Southern Railway from Cleveland to Erie, 941/2 miles, we found the force required to draw a stock train of 709 tons to be 2,498,396,320 footpounds, exclusive of the force to move the locomotive itself. We

By W. A. Heitbrink, J. D. Ashley, R. E. Gresh, J. A. Organiscak, A. B. Cecala

Many different types of mobile equipment used in surface coal mining utilize enclosed cabs to protect equipment operators. The overburden removal process is extremely dusty and can cause excessive exposure to respirable dust, especially crystalline silica. After equipment is used for years, many components of the enclosure deteriorate and its effectiveness is greatly reduced. This report discusses a cooperative research study performed on an Ingersoll Rand DM45E surface drill, retrofitted with a new Sigma pressurization and filtration system. Respirable dust concentrations were substantially reduced from 0.64 mg/m3 during pre-testing to 0.05 mg/m3 during post-testing with the new system, representing a 92% reduction in dust levels in the drill cab. This new system appears to be a very well-built and sturdy device, well-suited for the mining industry.

By H. K. van Poollen, H. C. Bixel

A treatment is given of the transient pressure behavior of a well located at the center of a circular region surrounded by a radial discontinuity. On either side of the discontinuity, the values of permeability, viscosity, compressibility and porosity are uniform but may be different from those on the other side of the discontinuity. The results are obtained by solving a pair of finite difference equations. The numerical solution to these equations is obtained using a digital computer. The results are compared with previously published, approximated analytical solutions to the same problem. Solutions, presented graphically, show pressure decline for constant rate fluid production. The range of variables studied include dimensionless time from &apos;0.001 to 100 and storage capacity ratio from 0.001 to 1,000. The well behaves as if it were in an infinite reservoir for dimensionless times less than 0.25. Reservoir properties near the well can be estimated in the usual manner. An overlay technique is used to match an experimental curve with one of the theoretical curves. It is possible to estimate the distance to a discontinuity by substituting the actual time t and the corresponding dimensionless time tD at which a match occurs into the equation a = (0.000264 tk1/tD , µ1 cI)I/2 where kI/ I µI cI is the diffusivity near the well, and may be estimated from data taken at early time. Several buildup curves are computed. These curves show that for early shut-in times, correct values for transmissibility are obtained from conventional analysis. However, erroneous values of static reservoir Pressure are obtained unless data at large shut-in times are taken. INTRODUCTION A mathematical treatment of the transient pressure response of a well located at the center of a region bounded by a circular discontinuity is given. Within a region (Fig. 20) the properties of both the rock and the fluid are considered to be constant on either side of the discontinuity. While these properties are considered constant, they may be different on opposite sides of the discontinuity. A discontinuity of this type could be a fluid-fluid contact or a sudden change in rock characteristics such as thickness, porosity or permeability. Analytical solutions to this problem are available. 1-3 However, they are so involved that they are of little practical use. An approximate solutionl is available but the range of times over which it is valid has not been specified. A numerical solution to a pair of finite difference equations is used to obtain the solution given in this paper. PREVIOUS WORK One of the first solutions to the problem was published by William Hurst.1 Hurst considered unsteady-state flow of fluids through two sands in series with different mobilities in each sand. He used Laplace transforms to obtain a solution for a single well located at the center of the circle enclosing the first of the two sands. In this case, the solution for the pressure change in Region I (Fig. 20) is2

By Minna Rämä

Iron containing leach residues like jarosite and goethite from electrolytic zinc production contain many valuable metals and harmful substances. These metals and substances should be removed in order to obtain an acceptable, stable and reusable product, and maximize economic feasibility as well as minimize environmental footprint. In this work, the processing of jarosite leach residue was studied in laboratory scale experiments under oxidizing and reducing conditions at high temperatures. First, the pretreated material was melted and oxidized to produce a melt of metal oxides. Second, the oxide melt was reduced in CO–CO2 atmosphere. Target after the reduction step was to obtain a clean slag and a liquid metal or speiss phase that collects the valuable metals, such as silver. The kinetics of the thermal processing were studied for determining optimal times and conditions for the aforementioned process steps. The preliminary results show that the process is thermodynamically feasible, and the desired phases can be obtained in the experimental conditions investigated.

By Steven J. Page, John A. Organiscak

Airborne dust generation is one of the byproducts of coal mining, processing, and handling. The amount of airborne total dust (ATD, respirable size and larger) and airborne respirable dust (ARD) generated is of primary interest for designing the level of engineering controls needed for adequate dust abatement. Laboratory crushing experiments were conducted in a wind tunnel with a roll crusher to identify relationships among crushing parameters, product size, coal rank properties, and airborne dust generation. Through the first series of experiments, the effect of primary and secondary breakage processes on both product size and airborne dust generation was examined. Through a second series of experiments, the effect of coal rank properties on product size and airborne dust generation was studied using a uniform crushing process with secondary breakage. Laboratory results indicate that secondary breakage of a particular coal notably increases the specific amount of ATD generated, while negligibly impacting the specific amount of ARD generated. A strong positive relationship was identified between the specific amounts of ATD and ARD generated during the primary breakage process (with minimal secondary breakage), but a negligible relationship was observed between the same two variables when secondary breakage was introduced into the crushing process. This indicates that most of the ATD and ARD is generated from the primary breakage, while secondary breakage has a more of an influence on generating additional amounts of larger sized ATD. Additional experiments involving the uniform crushing of eight different bituminous coals showed that the coal rank, expressed as the inherent moist fuel ratio (MFR = fixed carbon =(volatile x inherent moisture)), had diverse relationships between the product size created and the amount of airborne dust generated. As bituminous coal rank or MFR increased, the amount of coal product fines < 250 gm increased while the mass percentage of ATD and ARD liberated from these < 250 µm product fines decreased. Air dry loss (ADL) moisture in the coal was found to be inversely related to the dust cloud electrostatic field, influencing dust liberation from the coal product fines. Since the MFR was directly related to the dust cloud electrostatic field, opposite the ADL-electrostatic field relationship, the diverse relationships between the product size created and the amount of dust liberated from the < 250 µm product fines were explained. Finally, 12 to 14 times more ATD was generated as compared to the ARD generated during these experiments. These results should provide a fundamental basis for initial estimation of the airborne dust loading requirements of engineering control methods for coal crushing.

By R. C. Davis, R. F. Berry, G. W. White, B. T. O’Connell, L. A. Stacha

The formation density logging tool provides a radioactivity measurement that yields formation densities in situ. The relationship between bulk density and porosity is well understood. With knowledge of grain and fluid densities, porosity may be computed from the indicated formation bulk densities in shale-free formations. The porosities thus determined may be used with a resistivity log for water-saturation determinations. One technique utilizes a density vs resistivity plut. A plot of density vs Sonic-log transit time is used for porosity determinations in shaly sands. This method is particularly suited to wells drilled with oil-base or salt muds. In shale-free formations, comparisons of density values nnd neutron-log readings are used to identify lithologr and, thus, to select appropriate values of grain density for porosity computations. Through the use of Formation Density, Sonic and neutron logs, the interpretation problems caused by complex matrix lithologies are simplified. Other applications of the Formation Density log are found in the identification of minerals in evaporite deposits and in yield determinations of "oil shales". INTRODUCTION Widespread field application has demonstrated that the measurement of formation density is a useful and revealing technique for well logging. Responding to the bulk density variations of the formation, the Formation Density log affords valuable data on the porosity, lithology and fluid content of the formations. Although not without its own limitations, the Formation Density tool may provide effective interpretation under conditions that hamper or preclude the use of other porosity devices. When used in conjunction with other devices, such as the Sonic or neutron, complex matrix conditions may be better understood, defined and evaluated. A previous paper&apos; described the valuable contribution of the Formation Density tool in the logging of empty, or gas-filled, holes. The purpose of the present paper is to describe applications of the device in liquid-filled holes. THE FORMATION DENSITY TOOL The Formation Density tool was devised to measure the bulk densities of formations in situ. Actually, the device responds to electron density, but in the overwhelming majority of cases of interest, the electron density is very closely proportional to the bulk density. In other cases appropriate corrections can be made if necessary. Comparisons of log-derived densities with true densities for the more common matrix minerals are shown in Table 1. The tool consists of a gamma-ray source and detector mounted in a skid which, during the logging operation, is in contact with the borehole wall (see Ref. 1 for schematic). Gamma rays are emitted by the source and diffused through the formation. The number of diffused gamma rays reaching the detector at a fixed spacing from the source are counted. An increase in counting rate by the detector indicates a decrease in bulk density in front of the skid. Conversely, a decreased counting rate signifies an increase in bulk density. A measurement of hole diameter, between the face of the skid and that of the eccentering arm, is recorded simultaneously with the measurement of diffused gamma rays. Since the tool is a wall-contact device, the size of the borehole has little influence, provided good contact is maintained with the wall of the hole. Only in extremely large or small boreholes does the actual diameter become significant. However, for most accurate measurements the borehole size should be taken into account. Fig. 1 presents the departure curves for the conversion of counting rate to bulk density for liquid-filled holes of various sizes. It is of utmost importance that the skid maintain good contact with the wall of the hole. If, due to roughness or caving, there is mud between the skid and the formation, the tool will include in its response the relatively low-density mud, and the apparent density reading will be too low. Normally, permeable beds do not cave appreciably, so that reliable readings are usually available for zones of interest. Nevertheless, the caliper reading over the zone of interest should be examined for any wall roughness. When mud cake exists between the skid and the formation, the Formation Density log sees it as part of the formation. When thick mud cakes exist, a correction is required. For best results in wells having thick mud cakes,

By H. S. Price, D. A. T. Donohue

The system of equations describing displacement of a hydrocarbon liquid by a hydrocarbon vapor in a porous medium where mass transfer takes place between the phases is solved numerically for a variety of gas injection processes. Even though the method of solution is quite general, only systems with three hydrocarbon components are considered. Computer simulations of displacement processes wherein mass transfer between phases is both considered and neglected are compared, and it is shown that neglecting mass transfer can give pessimistic displacement efficiencies. INTRODUCTION The role of the gas displacement process in the recovery of petroleum has been subjected to a series of detailed analyses; as a result, a number of predictive models have been published in the literature. However, because of major simplifying assumptions, most of these models do not completely represent the physical system. As a result, the effect of making the simplifying assumptions is unknown. Therefore, a complete representation of this process — one without major simplifying assumptions —should lead to a fuller understanding of the process, and perhaps to methods of improving it. The general method of developing a model for two-phase fluid flow in a porous medium is to solve simultaneously the continuity equation, the energy equations and the equation-of-state for each phase under the prescribed initial and boundary conditions. For an isothermal system, the energy equations reduce to the momentum equation. Darcy&apos;s law. However, since natural gas is the vapor state of the reservoir liquid, interphase mass transfer may take place with concomitant changes in both the intensive and extensive thermodynamic properties of each phase. It is this phenomenon that has often been omitted in previous mathematical models. An additional relation, then, which accounts for mass transfer between the phases, must be included with the other equations to specify a complete model. Completely formulating the equations to be solved is not a difficult task1 but obtaining their solution has been intractable up to now. Availability of large-memory, high-speed digital computers now makes an attack on this formidable problem possible. This paper presents a preliminary study of the problem. Since this investigation is intended to be exploratory, it is restricted to the linear, horizontal, isothermal, two-phase viscous flow of oil and gas in an oil reservoir. In the early development of predictive models of this process, the reservoir system was considered as a unit and various forms of the material balance equation were proposed.2-4 Pressure and saturation gradients were then added in the Buckley-Leverett model.5 The Buckley-Leverett formulation considered the fluids to be incompressible; thus, the mathematical model reduces to a steady-state system. In the 1950&apos;s, studies incorporating numerical techniques were being published.6-9 These mathematical models differed in the efficiency of finite difference techniques, the inclusion or exclusion of capillarity or the number of space dimensions considered. To solve these nonlinear, partial differential equations, each phase was considered to be homogeneous with time; therefore, mass transfer between phases was neglected. The effect of mass transfer on the gas displacement process was first reported by Attra. 10 He simulated the one-dimension flow system by a series of cells in each of which the fluids were equilibrated during a time step. In addition, the pressure throughout the system during each time step was predetermined and constant-phase velocities were calculated according to the Buckley-Leverett incompressible fluid flow model. Welge et al.11 developed a model for the displacement of oil by an enriched gas where composition is considered to be a dependent variable. Fluid

By Peter Kovalchik, Ed Kwait, T. Michael Durr

1. BACKGROUND Many research projects on engineering controls for noise reduction in mining were conducted by the former U.S. Bureau of Mines, mostly under contracts from 1972 through 1986.1 Contracts were awarded to determine which mining equipment was responsible for worker noise exposure over the permitted Federal Regulation level of 90 dBA for 8 hours. Dominate noise sources, for each piece of equipment was also determined. The final goal was to develop engineering noise controls for those pieces of equipment and then evaluate them. This was the general approach taken in each research project or contract. This paper deals with what is known about the control of noise from continuous miners, one of the most commonly used underground mining machines. A literature review on continuous miners revealed that the relevant noise sources were divided into four categories: conveyor, cutting head, drive train, and motor noise. The dominate noise sources reported were the conveyor noise and the cutting noise.2 Conveyor noise consists of impacts and scraping at various locations on the conveyor structure. These impacts are associated with discontinuities on the top and bottom decks, impacts between the chain and the tail roller, impacts on the sidewalls at path points of discontinuity under horizontal pivot, and impacts on the flex plate.3 Scraping occurs along the entire length of the chain conveyor. The other dominate source, the cutting of coal, has also been addressed in past research.4, 5, 6 The research presented in this paper only addresses the controls associated with the conveyor. The literature suggests several effective treatments for noise control: retrofitting the chain conveyor with a urethane coating or a urethane sleeve on the chain flights, using a urethane coating or urethane sleeve on the tail roller, constrained layer damping of the decks, and the use of a modified take up plate.7, 8 However, the in-mine durability of these concepts has yet to be proven for the conveyor system. This paper analyzes extensive noise and urethane durability testing on a Joy 14CM9 continuous miner’s conveyor assembly, tail roller, and bottom plate conducted at the Pittsburgh Research Lab facilities. It will also discuss the initial underground testing results for the urethane-coated conveyor flights and tail roller.

By S. C. Tadolini, T. M. Barczark

Mines in the western United States have had limited choices for standing support. Wood cribs were often too soft and unstable. The introduction of the Can support in the earl v 1990s provided an effective alternative, (lilt/ it remains the dominant form of tail¬gate support. Water-filled prestressing cells are now used to cap the Can and preload it to provide an active roof load. The Cluster Prop, consisting of three timber wedge props bundled to¬gether; provides more capacity than (m equivalent sized Call support and improves transport efficiency. However the Cluster Prop is less stable and does not maintain a consistent load throughout its loading profile. Pumpable roof supports are another alternative support, but the \&apos; have not been proven in high deformation en¬vironments. This paper compares the performance characteristics o f these various support systems.

By Henry M. Howe

I wish to present to you a few thoughts on some of the phenomena and laws of iron smelting. Owing to the great complexity of the subject, to the great variety of points to be taken into consideration, many of which are very poorly understood, and to the meagreness and even conflictoriness of our information with regard to some of the most important laws which govern the subject, the fruits of such thoughts as I venture to offer you must be received as speculations, not as facts. Nevertheless, in discussing old phenomena from new standpoints, thus furnishing a metallurgical parallax, if I may say so, these theoretical speculations may have their value in helping to a clearer comprehension of the phenomena and laws we now know, and in suggesting new lines of inquiry. While an increase of height in blast furnaces is not always followed by increase in their power of production, experience proves that it tends to increase it; for while we have many cases of short furnaces producing more iron than longer ones, yet enormous productions, such as those of the Lucy and Isabella furnaces of Pittsburgh, and of the furnaces of Esch sur l&apos;Alzette, in Luxembourg, have never been reached in short furnaces. We may safely infer that height is an element essential to great production, though of course not the only essential element, and that, in the case of high furnaces which are not capable of great production, some other essential element is wanting. Moreover, experience teaches that within limits increase of height tends to increase the producing power in a still higher ratio. Thus, in the Esch furnace, which is 19.8 meters (65 feet) high, 393 tonnes (or 387 gross tons) of 31 1/2 per cent. Ore

By Launa G. Mallett, Dana Reinke, Charles Vaught, Michael J. Brnich

As mines become safer and major disasters fewer, the number of experienced emergency responders is decreasing. This decrease will create a gap in response expertise which could have serious ramifications during future mine disasters. While working toward safety goals which may make emergency response obsolete, it would be reckless not to acknowledge that the potential for disaster still exists and that the protection of miners in such circumstances must remain a priority. The Mine Emergency Response Interactive Training Simulation (MERITS) is a computerized mine emergency simulation that meets a variety of needs. It allows personnel in leadership positions to test their knowledge and skill. Groups of individuals composed of representatives from mining companies, labor, and government agencies can practice working together during the simulated mine emergency much in the same way an actual emergency would require. An individual could also run the program to enhance his or her response skills. With this training tool, responders will be able to learn from their mistakes before facing situations with potentially catastrophic consequences. This paper discusses MERITS and its use in providing command center training.

By John Fulton

THE increase in the production of iron has been accompanied by a growing demand for an improved quality, and more especially at the present time, in the manufacture of Bessemer steel, which is rapidly becoming an important branch of industry. This has led the makers of pig iron to a careful investigation of the composition of the materials from which their metal is produced, the inquiry being greatly assisted by a cordial alliance of science and practice. Formerly, chemical science was held in abeyance, or admitted in a hesitating experimental way ; but now it is received as a valuable auxiliary, and its decisions are accepted as final and conclusive. It is called on to assist the iron-maker in determining the quality of his stock, and to detect the presence of injurious elements in his fuel, ores, flux, or iron. The object of this paper is to submit the method now in use at the furnaces of the Kemble Coal and Iron Company in the Broad Top coal and iron region, for removing, by a process of crushing and washing, slate and other impurities from coal, designed, when coked, for furnace fuel. It is not contemplated to claim very advanced progress in this work, believing that it is susceptible of improvement, but to show that some progress has been made in a comparatively new field, and it is hoped in the right direction, since coke is probably destined to become the principal fuel in the metallurgy of iron. The Broad Top coal region occupies an isolated geographical position, standing 25 miles east from the Alleghany field. It is associated with the latter by the structure of its coal, and more closely with the Cumberland field by a similarity in the quality of coal.

By Wing Ka Ng

Substitution of pulverized coal injection by solid biocarbon fuel has the potential to achieve substantial reduction in GHG emissions associated with blast furnace ironmaking. A systematic evaluation was conducted on the performance of solid bio-carbons produced from a single raw biomass source using different pyrolysis technologies. The potential of solid biocarbon in reducing GHG emission of the blast furnace ironmaking process is strongly influenced by its O/C mass ratio. In order to achieve substantial GHG reduction, it is necessary to replace coal injection by solid biocarbon having a low O/C mass ratio. The pyrolysis technology and conditions employed are key parameters influencing O/C mass ratio of the resultant solid biocarbon. Close collaboration between steelmakers and solid biocarbon producers is critical for producing suitable solid biocarbon fuel to replace pulverized coal injection. A successful partnership should pave the way in achieving substantial reduction in GHG emissions of the blast furnace ironmaking process.

By D. E. Menzie, D. L. Dauben

This paper discusses the physical parameters involved in the slow flow of high molecular weight polymer solutions in porous media. The interacting effects of polymer properties and porous media properties on flow performance are considered. Experiments were conducted with the polyethylene oxides, with molecular weights ranging from 200,000 to over 5,000,000. Frontal advance velocities ranged from I to 30 ft/day. The porous matrix consisted of a flow cell packed with glass beads. Polymer solutions were characterized by viscosity and normal stress measurements. Under certain conditions, unexpectedly high flow resistance was observed. This behavior was observed to be a function of flow rate, pore size, polymer molecular weight and concentration. The polymer solutions exhibit "dilatant" flow behavior in porour media in contrast with the pseudo-plastic behavior in simple flow systems. A theoretical ex-planation of such behavior is presented. INTRODUCTION The use of polymers in the injected water of a waterflood increases oil displacement efficiency by reducing the mobility (k,/pu) of the driving phase. A reduced driving phase mobility results in improvements in the areal sweep efficiency and in the vertical coverage in stratified reservoirs. This mobility reduction may be achieved by a permeability reduction, a viscosity increase or by a combination of the two. Early attempts at increasing the injected water viscosity were not successful because of the poor economics involved. The use of such materials as glycerin, sugar or glycols to increase water viscosity was not economically feasible. Attempts in using certain naturally occurring polymers were not too successful because of the high polymer losses to the rock. A high molecular weight, partially hydrolyzed polyacry-lamide was introduced 3 years ago as a waterflood additive.&apos;,&apos; Initial work by Pye&apos; indicated that the presence of these polymers in dilute concentrations decreases the water mobility 5 to 20 times more than would be expected from measurements of the solution viscosity. Such an effect would be of obvious economic value since only a small polymer concentration would be required to accomplish a large reduction in water mobility. This research was designed to study the basic flow mech anisms of polymer solutions in porous media. The interacting effects of polymer properties and porous media properties on flow performance are considered. This study indicates some of the conditions under which these interactions can lead to significant mobility effects. is valid only for Newtonian fluids. For polymer solutions and other non-Newtonian fluids the equation must be modified to consider that viscosity is a variable quantity. Modification of the Darcy equation to include non-Newtonian effects has been the subject of several recent investigations."" The modifications generally adopt a rheological model. such as an Ellis or Dower law model. to Dorous media by defining some characteristic channel radius. Most of these studies showed the porous media flow behavior to be predictable from viscometric data. Investigations involving the flow of high molecular weight polyacrylamide solutions through cores have generally encountered the high flow resistances reported previously by Pye. This high flow resistance has generally been attributed to an in-depth permeability reduction, as evidenced by a reduced permeability to water which has displaced polymer solution from the porous media. Marshall and Metzner" report high flow resistances, which they attribute to viscoelastic effects. In this paper, the effects of polymer molecular weight, pore size, flow rate and concentration are considered. The polymers used are the polyethylene oxides known as Poly-ox. This class of polymers was used because of its availability in a wide range of molecular weights and because of its known ability to propagate well through porous media. THEORY PHYSICAL PROPERTIES OF POLYMER SOLUTIONS The polymer molecule dissolves in water by means of hydrogen bonding, but retains some of its own structural identity while in solution. Nonionic polymers, such as polyethylene oxide, are generally considered to have a random coiling configration. This type of molecule has the ability to "sequester" or hold a large volume of solvent within its coils in a manner similar to that of a sponge. The random coil is easily deformed and under an applied stress

By L. McWilliams, L. D. Patts, J. D. Noll, S. E. Mischler

Elemental carbon (EC) is currently used as a surrogate for diesel particulate matter (DPM) in underground mines since it can be accurately measured at low concentrations and diesels are the only source of submicrometer EC in underground mines. A disadvantage of using EC as a surrogate for DPM is that the fraction of EC in DPM is a function of various engine parameters and fuel formulations, etc. In order to evaluate how EC predicts DPM in the underground mining atmosphere, measurements of total carbon (TC; representing over 80% of the DPM) and EC were taken away from potential interferences in four underground metal/non-metal mines during actual production. In a controlled atmosphere, DPM mass, TC, and EC measurements were also collected while several different types of vehicles simulated production with and without different types of control technologies. When diesel particulate filters (DPFs) were not used, both studies showed that EC could be used to predict DPM mass or TC. The variability of the data started to increase at TC concentrations below 230, µg/m3 and was high (>+20%) at TC concentrations below 160 µg/m3, probably due to the problem with sampling organic carbon (OC) at these concentrations. It was also discovered that when certain DPFs were used, the relationship between DPM and EC changed at lower DPM concentrations.

By R. L. Slobod, C. Gatlin

This .study defines the basic mechanism of the mis-cible displacerrzent of oil and writer from porous Medici by various water-driven alcohol .slugs. Three distinct alcohol slug processes were .studied. Considerable data concerning the quanity of alcohol required for oil recovery were also obtained. All data were obtained in a 1-in. diameter, 100-ft long, unconsolidated core. The porosity of this system was 35 per cent. and the permeability was approxitrlately 4 darcies. Total core pore volume wax 5,716 cc. All displacements were conducted at a constant injection rate of 5 to 6 cc//min, which corresponds to a frontal advance of 5 ro 6 ft/hr. The first portion of this paper is concerned with 111 use of one alcohol—isopropyl—a\. the slug material. Isopropyl alcohol (IPA) is completely miscible with both oil rind water; however, miscibility of the threc-component systems, oil-water-IPA, requires a relutively. high concentration of IPA. Hence, the displocement is not of the misoible type unless the IPA concentration is maintained above some critical value. A slug of IPA equal to only 13.5 per cent of the pore volume was jound to be sufficient to obtain complete recover?, of residua1 naphtha. In later studies two distinct process variations were developed. The firsr of these utilized methyl alcohol (MA) and IPA as slug materials. It was shown that methyl alcohol may he substituted for IPA at the front and rear of the slug with no loss of oil recovery. A .slug of 4 per cent MA-4 per cent IPA-4 per cent MA was sufficient for complere oil recovery. Because MA is considerably cheaper than IPA, this represents an important step toward economic application. A .second process variation used normal butyl alcohol (nBA) and MA as the composite slug, the nBA segnzent being injected first. This technique requires the smallest total slug size (approximately 10 per cent) of all processes studied. The high cost of nBA, however, precludes commercial application. It is possible that this basic process, subject to changes of alcohol type, may lead to a commrercicil process. INTRODUCTION Within the last 10 years, considerable study has been devoted to the general mechanics of miscible phase dis- placements in porous media. These studies have. in general, dealt with two-component displacernent. All reported field trials to date have been modified gas drives of one type or another. These utilize either lean gas at high pressure, rich gas at lower pressure or an LPG slug. The irreducible water content of the reservoir remains immobile during these processes. Although these techniques hold great promise. certain drawbacks do exist. Poor areal sweep efficiency, inherent in any displacement having a highly unfavorable mobility ratio, is one disadvantage. Furthermore, the miscibility of all processes which use gas is dependent on pressure. These pressure limitations may prohibit application to shallow reservoirs. There are also many areas where large quantities of LPG and natural gas are not readily available. These factors emphasize the need for improved techniques. The alcohol slug process is also a miscible-phase displacement process. It differs from the previously mentioned two-component techniques, however, in that both the reservoir oil and water are displaced by the slug. This behavior is a consequence of the miscibility of certain oil-water-alcohol systems. In the simplest case, a relatively small volume (slug) of an alcohol (such as isopropyl) is injected into the system. Water is then used to drive the slug through the medium. Thus. three components—-alcohol. oil and connate water-—exist at the front side of the slug. Miscibility is obtained at some alcohol concentration, this being dependent on the solubility of the particular system. Miscibility is maintained within the slug until the alcohol concentration falls below that value required to maintain miscibility. When miscibility is lost, the process reverts to a water flood. Certain inherent benefits of this technique are apparent. High pressures are not necessary to obtain miscibility in these liquid systems. Furthermore, water is a more desirable driving agent than gas because of the improved mobility ratio and the attendant improvement in areal sweep efficiency. The main disadvantage is, of course, the relatively high cost of alcohols. The use of an alcohol slug to recover reservoir oil is not a new idea." &apos; However, this process has received only limited study, presumably due to the lack of industrial interest caused by the seemingly prohibitive cost of alcohols. The main purpose of this study was to investigate the mechanism of the displacement of oil and water by various alcohol slugs and to develop process modifications aimed toward possible commercial application.