Search Documents

By R. H. Jacoby, V. J. Berry, R. C. Koeller

The experimental phase behavior of several field gas-condensate systems, one field volatile oil system, and a series of synthetic systems having gas-oil ratios from 2,000 to 20,000 scf/bbl stock tank oil was measured. The data were used to calculate the depletion performance of the field systems at their respective reservoir temperatures and of the synthetic systems at various temperatures. The results of the performance calculations were used to prepare correlations of total stock tank oil and separator gas in-place, and the amount of each recovered by primary depletion. Data needed to use the correlations are initial gas-oil ratio, initial tank oil gravity, reservoir temperature and reservoir pressure. The correlations presented should be useful for estiinating recovery from reservoirs producing volatile oils or rich gas condensates having gas-oil ratios from about 2,000 to 30,000 scf/bbl of stock tank oil. INTRODUCTION Prediction of depletion performance for gas-condensate reservoirs usually requires extensive laboratory work or lengthy phase-behavior calculations. For many small gas-condensate bearing zones the expense of such work is often not justified. Furthermore, where large holdings are involved, it is useful to have estimates of future oil and gas production in advance of the results of a laboratory analysis, even if such work is ultimately planned. For these reasons, it would be of value to have a method for rapidly estimating the depletion performance of gas-condensate reservoirs from the type of field data usually available. Few data on the reservoir depletion performance are available for the purpose of developing correlations. The increasing number of gas-condensate discoveries and the advent of high-speed computers have stimulated the development of methods for predicting performance. Such calculated performance data have been shown to be reliable and are becoming accepted as a basis for reserve estimates and for engineering studies. It therefore seems satisfactory to use results of performance predictions themselves for the purpose of developing the desired correlations. Such an approach is described in this paper. Several rich natural gas-condensate systems (gas-oil ratios of from about 3,600 to 60,000 scf/bbl) and one natural volatile oil system were studied (2,363 scf/bbl). In addition, to provide a more systematic basis for correlating purposes, a series of related, synthetic reservoir fluid mixtures was also studied (GOR's from about 2,000 to 25,000 scf/bbl). The purpose of this paper is to show how the recovery of oil and gas by primary depletion may be estimated from surface gas-oil ratio, reservoir temperature and pressure, and tank oil gravity. procedure Experiments Companion samples of gas and oil were collected from the high pressure separators in nine different fields at the time of their discovery. These samples were each recombined in accordance with the respective producing GOR to reproduce the reservoir fluids. Eight of these fluids, designated F-2 through F-9, were rich gas-condensate systems at the respective reser-

By Larry Patts, Michael J. Brnich

Approximately 45% of U.S. coal is produced from underground mining. The use of diesel engines to power under- ground mining equipment has steadily increased over the past four decades in an effort to improve mine safety and productivity. Several advantages realized with the use of diesel-powered mining equipment in underground coal mines are listed in Table I. The primary disadvantage of using diesel equipment in underground coal mines is that diesel exhaust emissions can contaminate mine ventilation air. The major constituents of diesel exhaust are gaseous emissions (which include carbon monoxide, carbon dioxide, oxides of nitrogen, sulfur oxides and unburned hydrocarbons) and diesel particulate matter (DPM). The Mine Safety and Health Administration (MSHA) has incorporated threshold limit values for all gaseous components of diesel exhaust into their regulations. These have been established by the American Conference of Governmental Industrial Hygienists.

By Lin Li

A reliability based analysis method for a drilled shaft stabilized slope system is presented in this paper. In the past effort, a deterministic method using the limiting equilibrium method of slices for determining the global factor of safety of a slope reinforced by a row of drilled shafts was developed using the soil arching concept. The drilled shaft stabilization mechanisms for the slope were treated as the drilled shaft induced soil arching, which reduces the driving forces on the down slope side of the drilled shaft. The effect of drilled shafts induced soil arching on the reduction of the driving stresses in the limiting equilibrium slope stability analysis was quantified by the load transfer factor through extensive finite element simulation studies. A semi-empirical equation was also developed for expressing the load transfer factor as a function of the soil properties, including strength parameters and unit weight as well as the slope geometry and soil profile, the location and spacing of the drilled shaft, and the dimension of the drilled shaft. However, due to the inherent uncertainties of the soil properties and the model error of the semi-empirical load transfer equation, a modification of the deterministic method into a probabilistic method is developed in this paper. The Monte Carlo statistical method is used to generate random variables for the soil strength parameters based on the prescribed probability characteristics, including mean, COV, and the probability distribution function. In addition, the modeling error of the load transfer factor is also treated as a random variable in the Monte Carlo simulation method, in which the mean, COV, and probability distribution function for the bias of the semi-empirical equation are used. The developed theories were coded into a computer program for analyzing complex slope geometry and slope profile conditions. Two examples are shown in the paper to illustrate the analysis results of the developed probability approach for determining the reliability of a drilled shaft stabilized slope system.

By F. W. Jessen, N. Mungan

The plastic flow characteristics of clay water suspensions were first recognized by Binghaml in 1916 and further studied by Ambrose and Loomis' in 1931-1932. Many physical and chemical properties of clay suspensions are deeply influenced by particle size distribution as well as by the exchange cation. Separation of a number of fractions is particularly helpful in making a detailed study of a suspension. A limited amount of work has been conducted on the effects of particle size on specific properties of mud drilling fluids. A knowledge of particle size distribution is essential for a better understanding of fundamental properties of clay suspensions, particularly viscosity and gel strength. The purpose of this investigation was to study the effect of particle size on the viscosity and gel properties of clay suspensions and to determine any changes in mineral composition accompanying variation in size. EXPERIMENTAL PROCEDURE Numerous methods may be used to fractionate a poly-dispersed clay suspension into nearly mono-dispersed systems. Particles larger than 44 micron (325-mesh) may be obtained by wet screening. For sizes from 44 to 1 micron, the fractionation may be accomplished by sedimentation, elutriation plus microscopy,' or turbidimetry.6 When dealing with systems which contain a major portion of particles below l-mi-cron size, slit ultramicroscopy,7 centrifuge methods of Svedberg,5 eams,9 and McBain,l0 and X-ray methods" may be employed. The Sharples super centrifuge has been proved suitable for the economical separation of suspended particles of submicron range.12,13,14 Three-hundred and forty-five gal of 1 per cent by weight Aquagel suspension was mixed in a high-speed 5-gallon mud mixer and the suspension was allowed to stand in 5-gal glass bottles for 30 days to assure full hydration. All particles larger than 44 microns were removed by wet screening. Five fractions in the range of 44 to 1 micron were obtained by sedimentation. The Sharples super centrifuge method described by Hauser and Reed.13 Norton and Speil,14 Ha user and Lynn,15 and Hauser and Schachman,10 as employed to yield five fractions of submicron size. A super centrifuge operation chart prepared by Fancher, Oliphant, and Houssierre12 was used to determine operating conditions for the desired particle ranges. The clay suspension, after removal of all material above 1-micron size, was centrifuged. During rotation of the bowl, the particles were deposited on a thin plastic liner which fit closely inside the bowl. After passing 5 gal of suspension through the centrifuge, the liner was removed and the particles on the liner were scraped off, remixed and recentrifuged. This was repeated five times. Thus, Fractions H, I, K, and L were obtained. The finest fraction, M, remained in an approximately 0.4 per cent suspension. Water was evaporated under reduced pressure from this suspension to yield the finest particles. Results of the fractionation are included in Table 1. In order to achieve proper orientation and humidity conditions for X-ray diffraction analysis, the following procedure was employed. The dilute suspensions were placed on glass slides and allowed to dry at room temperature. This was repeated several times. Previous to measurement each sample first was placed in a water desiccator for half an hour and then allowed to stand for 15 minutes at room temperature. thus yielding an equilibrium condition of about 52 per cent relative humidity. The relative humidity of the room in which the X-ray diffraction was carried out was maintained at approximately 50 per cent so that there was no change in the spacings during the X-ray examination. Samples

By Frank E. Chase, John L. Ellenberger, Christopher Mark

The nature of competition in the coal market tends to deplete the most favorable coal reserves first, and forces subsequent development of mines in more extreme ground conditions such as those associated with multiple-seam mining. In fact, 70% of the United States coal reserves are in multiple-seam situations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop mine design algorithms that will result in safer multiple seam mines. This paper presents an overview of multiple seam issues in the central Appalachian coalfields. To date, more than 50 case histories have been analyzed from 20 operating mines in Eastern KY, Western VA, and Southern WV. Each case history is classified according to the degree of multiple-seam interaction, ranging from no apparent interaction to severe interaction with direct impacts on mine safety and resource recovery. The case histories are also examined with regard to amount and geologic characteristics of interburden and overburden, and design stability factors. The sequence of mining has also been found to be critical when the lower seam is fully-extracted. This paper compares current case histories to traditional rules of thumb. In addition two situations were modeled using LaModel software. LaModel has been upgraded to import pillar grids and topographic data from AutoCAD files. The cases presented demonstrate vertical stress capabilities of LaModel.

This International Mine-Surveying Conference will take place in Budapest (Hungary) from 5 to 14 June, 1972. Detailed information can be obtained from the Mine-Surveying Working Committee of the Hungarian Mining and Metallurgical Society. Write: OMBKE Bányaméröi Munkabizottsag Budapest, V., Szabadsag ter 17, Hungary. SYMPOSIUM ON NICKEL The 'Gesellschaft Deutscher Metallhiitten-und Berglaute' is holding a Symposium on nickel on 24-25 September, 1970 at Wiesbaden, on the occasion of the G.D.M.B. Annual Meeting. Some 24 papers will be presented by metallurgists from many important companies around the world. Information may be obtained from The Secretary, G.D.M.B., Postfach 210, 03392 Clausthal-Zellerfeld, German Federal Republic. VISIT TO THE COUNCIL FOR SCIENTIFIC AND INDUSTRIAL RESEARCH On 23rd June, 1970, members of the Institute visited the C.S.I.R. in Pretoria. More members had booked for this tour but the current flu epidemic caused cancellations which was unfortunate. The visit was organised with military precision, which prevented detailed discussion of any particular subject, but provided a bird's eye view of a large number of interesting projects. The visit was packed with interest for all and those requiring further information were invited to contact the relevant divisions afterwards. Or Denkhaus welcomed the delegates and stressed the importance of integrating research efforts with industry's requirements. An excellent colour and sound film was shown which depicted the work of the Rock Mechanics division. This showed very clearly methods used for preparing rock samples and demonstrated the machines and instruments for the various tests. It made one realise the extent to which this research has been integrated with the actual mining situation. The fullscale experiments underground showed the failure of pillars under applied loads and were very interesting. This is undoubtedly a film which all mining people should see. After the film the rock mechanics laboratories were visited where the actual machines were seen and described. We then visited the metal and strength mechanics sections where the metallurgists were able to see some interesting experiments and tests. We also visited the Aeronautics Research group where a large 1 000 hp wind tunnel was inspected. We were told enough about this to realise something of the complexities involved in the design and operation of a closed circuit tunnel of this type. The tunnel is used for tests on models which are necessary for the design and modification of aircraft. After a very excellent lunch at the C.S.I.R. recreation centre, the delegates attended two lectures-one by Mr. Mandersloot of the Chemical Engineering group, who outlined the varied functions of this group and told us something of their work. Of particular interest was the research into the suitability of various South African manganese ores for dry cell batteries. Work on the thickener settlement studies interested the metallurgists. The second lecture was given by Mr Donaldson of the National Building Research Institute. This Institute has about ten divisions each of which covers a particular aspect of building research. The work of the soil mechanics division was described in detail and illustrated by coloured slides. This was particularly interesting and demonstrated clearly how building failures result from lack of attention to detail of construction where unstable soil conditions exist. Cracks in walls of compound blocks brought the subject home forcibly to the mining delegates. This division has also caried out important work on sinkholes and sUmes dams and produced some positive results. Altogether the visit was most interesting and enjoyable. It was made more worthwhile because the emphasis was on the work being carried out and not on just seeing the laboratories. The Institute is greatly indebted to the C.S.I.R. and its staff for the very excellent arrangements made.

By Dennis Cox, Stephen P. Signer, Joanne Johnston

A method to assist in the evaluation and selection of roof bolts using in situ measurements of roof bolt loading has been developed by researchers of the Spokane Research Center, National Institute of Occupational Safety and Health. Both axial and bending forces are measured by strain gauges at many locations along the length of fully grouted bolts during various stages of mining. This information is then used to (1) predict bolt loading for variations in bolt spacing, grade, and diameter, (2) calculate the design changes necessary in zones where bending loads are high, and (3) determine if bolt length is adequate. Results from several case studies of full-column bolt loading in coal mine gate roads are used to illustrate the design method. This knowledge will give design engineers a tool for the selection of roof support systems that will improve underground safety by reducing roof bolt failures.

Proceedings of the Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry, Montreal, June 1970. The Ninth International Symposium on Techniques for Decision-Making in the Mineral Industry was sponsored by The Canadian Institute of Mining and Metallurgy, McGill University and Ecole Poly technique. The programme included 71 papers on various topics, as follows: Market Analysis and Logistics Planning; Quantification of Geological Variables; Blending; Capital Investment Decisions; Mining; Financial and Economic Analysis; Search for Mineral Deposits; Market Forecasting and Strategies; Operations Research in Process Modelling; Ore Reserve Estimation; Management Information Systems; Optimization and Control of Mineral Processes. In addition to general sessions, a special feature of the Symposium was Executives' Day, which was held to provide top and middle management with a broad understanding of the usefulness of decision-making techniques and their role in the mining organization. Panel Discussions and two keynote speakers provided a review, in non-technical terms, of the areas in which decision-making techniques have proven valuable. The present volume contains 65 papers submitted for publication, along with a complete account of the Executives' Day discussion. It is broadly divided according to the above subject headings. Approximately 550 pages, illustrated. Price: $15.00; $12.00 to students, plus 50 cents for handling costs. Order now from CIM headquarters: Canadian Institute of Mining and Metallurgy, 906-1117 Ste. Catherine St. W. Montreal 110, Quebec.

By P. J. Root, J. E. Warren

An idealized model has been developed for the purpose of studying the characteristic behavior of a permeable medium which contains regions which contribute significantly to the pore volume of the system but contribute negligibly to the flow capacity; e.g., a naturally fractured or vugular reservoir. Unsteady-state flow in this model reservoir has been investigated analytically. The pressure build-up performance has been examined in some detail; and, a technique for analyzing the build-up data to evaluate the desired parameters has been suggested. The use of this approach in the interpretation of field data has been discussed. As a result of this study, the following general conclusions can be drawn: 1. Two parameters are sufficient to characterize the deviation of the behavior of a medium with "double porositym from that of a homogeneously porous medium. 2. These parameters can be evaluated by the proper analysis of pressure build-up data obtained from adequately designed tests. 3. Since the build-up curve associated with this type of porous system is similar to that obtained from a stratified reservoir, an unambiguous interpretation is not possible without additional information. 4. Differencing methods which utilize pressure data from the final stages of a build-up test should be used with extreme caution. INTRODUCTION In order to plan a sound exploitation program or a successful secondary-recovery project, sufficient reliable information concerning the nature of the reservoir-fluid system must be available. Since it is evident that an adequate description of the reservoir rock is necessary if this condition is to be fulfilled, the present investigation was undertaken for the purpose of improving the fluid-flow characterization, based on normally available data, of a particular porous medium. DISCUSSION OF THE PROBLEM For many years it was widely assumed that, for the purpose of making engineering studies, two param- eters were sufficient to describe the single-phase flow properties of a producing formation, i.e., the absolute permeability and the effective porosity. It later became evident that the concept of directional permeability was of more than academic interest; consequently, the degree of permeability anisotropy and the orientation of the principal axes of permeability were accepted as basic parameters governing reservoir performance. 1,2 More recently, 3-6 it was recognized that at least one additional parameter was required to depict the behavior of a porous system containing regions which contributed significantly to the pore volume but contributed negligibly to the flow capacity. Microscopically, these regions could be "dead-end" or "storage" pores or, macroscopi-cally, they could be discrete volumes of low-permeability matrix rock combined with natural fissures in a reservoir. It is obvious that some provision for the inclusion of all the indicated parameters, as well as their spatial variations, must be made if a truly useful, conceptual model of a reservoir is to be developed. A dichotomy of the internal voids of reservoir rocks has been suggested.7,8 These two classes of porosity can be described as follows: a. Primary porosity is intergranular and controlled by deposition and lithification. It is highly interconnected and usually can be correlated with permeability since it is largely dependent on the geometry, size distribution and spatial distribution of the grains. The void systems of sands, sandstones and oolitic limestones are typical of this type. b. Secondary porosity is foramenular and is controlled by fracturing, jointing and/or solution in circulating water although it may be modified by infilling as a result of precipitation. It is not highly interconnected and usually cannot be correlated with permeability. Solution channels or vugular voids developed during weathering or burial in sedimentary basins are indigenous to carbonate rocks such as limestones or dolomites. Joints or fissures which occur in massive, extensive formations composed of shale, siltstone, schist, limestone or dolomite are generally vertical, and they are ascribed to tensional failure during mechanical deformation (the permeability associated with this type of void system is often anisotropic). Shrinkage cracks are the result

By John J. Sammarco

Computer-related accidents have caused injuries and fatalities in numerous applications. Normal Accident Theory (NAT) explains that these accidents are inevitable because of system complexity. Complex systems, such as computer-based systems, are highly interconnected, highly interactive, and tightly coupled. We do not have a scientific methodology to identify and quantify these complexities; specifically, NAT has not been operationalized for computer-based systems. Our research addressed this by operationalizing NAT for the system requirements of safety-related computer systems. It was theorized that there are two types of system complexity: external and internal. External complexity was characterized by three variables: system predictability, observability, and usability -the dependent variables; internal complexity was characterized by modeling system requirements with Software Cost Reduction dependency graphs, then quantifying model attributes using 15 graphtheoretical metrics the independent variables. Dependent variable data were obtained by having 32 subjects run simulations of our research test vehicle: the light control system (LCS). The LCS simulation tests used a cross-over design. Subject perceptions of these simulations were obtained by using a questionnaire. Canonical correlation analysis and structure correlations were used to test hypotheses 1 to 3 - the dependent variables predictability, observability, and usability do not correlate with the NAT complexity metrics. Five of 15 metrics proposed for NAT complexity correlated with the dependent data. These 5 metrics had structure correlations exceeding 0.25, standard errors < 0.10, and a 95% confidence interval. Therefore, the null hypotheses were rejected. A Wilcoxon signed ranks test was used to test hypotheses 4 to 6 - increasing NAT complexity increases system predictability, observability, and usability. The results showed that the dependent variables decreased as complexity increased. Therefore, null hypotheses 4 to 6 were rejected. Lastly, this work is a step forward to operationalize NAT for safety-related computer systems; however, limitations exist. Opportunities addressing these limitations and advancing NAT were identified. Lastly, the major contribution of this work is fundamental to scientific research - to gain knowledge through the discovery of relationship between the variables of interest. Specifically, NAT has been advanced by defining and quantifying complexity measures, and showing their inverse relationship to system predictability, observability, and usability.

By Mike Dry

Conventionally, lithium-bearing brines are processed via solar evaporation, chemical purification, and either electrolysis to lithium hydroxide or precipitation of lithium carbonate. Lithium-ion battery technology and electric vehicles are forecast to greatly increase the demand for lithium, but not all lithium-bearing brines are amenable to the conventional extraction process and new approaches are being developed. The chemistry associated with conventional lithium extraction is outlined and two new approaches are discussed.

By J. P. G. Pretorius

The size effect in tests of the compressive strength of coal specimens differs from predictions based on the Weakest Link theory. Predictions of the size effect in tensile tests on lengths of cotton yarn and glass fibre, the behaviour of which is analogous to the weak link process, also differ from observations. This discrepancy is shown to be caused by the correlation between the strengths of the unit lengths in a composite specimen. The Weakest Link theory is reformulated as the Weakness Correlation theory to account for such correlation. It is shown that weakness correlation is found in rock and it is concluded that at least part of the discrepancy between the predicted and observed size effect in rock strength tests could be attributed to this correlation.

By V. Blet

Rare earth elements (REE) are regarded today as highly critical raw materials but currently lack suitable recycling processes. A combined hydro- and pyrometallurgical process aimed at REE recovery from used NdFeB permanent magnets was recently developed by the CEA. The process integrates the physico-chemical treatment of magnets, followed by a solvent extraction step for the recovery and intra-REE separation using a selective extractant. A subsequent pyrometallurgical treatment via molten chloride salt electrolysis allowed the isolation of pure Dy metal. Technical-economic assessment and life-cycle analysis were also conducted. Following this first successful demonstration, a new project aimed at the recovery of REE from end-of-life nickel-metal-hydride batteries is currently being developed in association with industrial and academic partners. The project aims at evaluating from an experimental and economic perspective different processes converging at the production of value-added products such as cermet materials for catalytic applications, purified REO concentrates, or metallic alloys.

By John Durkin, Harry Dobroski

This paper presents a general overview of the Bureau of Mines&apos; programs in the areas of operational and post-disaster communications. These programs encompass both hardware developments and system evaluations. Topics discussed include a new visual paging system compatible with existing pager phone lines, a means of modifying commercially avail able pager phones to permit selective paging and message leaving, a multiplexed telephone system that uses twisted shielded pair and requires no central control, medium frequency hardware developments, and a manual for mine communications. Research has continued in the area of post-disaster location and communications. This research is based on seismic and electro- magnetic techniques. Each has been extensively studied and field tested to better understand its ability to perform effectively. A brief description is given of the post-disaster program. Results are promising and provide insight into future areas of research.

By R. Karl Zipf, Kousick Biswas

The main objective of occupational health and safety research is to minimize or eliminate the events that may cause fatal or non-fatal injuries to human workers. A commonly used technique is to devise an “incident prevention plan”, which is more often the product of thorough investigations of past reported incident events. Incident documentation and methodical reporting and systematic and thorough data collection, often help identify the root cause of the incident – in other words, the etiology of the incident. These retrospective analyses of the incidents can efficiently identify the future steps to take to achieve the objective of minimizing occurrence of “events of interest”. This paper introduces a novel technique – “Taxonomic Analysis”, which identifies the root causes of an event (an incident in this case) and can provide future direction for corrective measures to reduce the probability of occurrence of the event. A taxonomic analysis involves systematic and organization of data based on observation, description, and classification. This paper utilizes the rock fall related incident narratives, available with the Mine Safety and Health Administration (MSHA) database (1984-1999), for a taxonomic analysis. The study found that 67.6% of groundfall incidents occurred in supported areas with the remainder (32.4%) in unsupported areas. Some form of rock mass failure appears to cause about 50% of groundfall incidents, although in 39.7% of the overall groundfall incidents or two-thirds of those involving rock mass failure, the exact nature of the rock mass failure could not be determined from the narratives. Human activities factors such as scaling or barring down, drilling or bolting, and setting timbers or cribbing accounted for another 34.5% of the groundfall incidents. Finally, support system failures made up the remaining 15.5%. Results from this taxonomic analysis may suggest focus areas toward which preventive measures and future research activities could concentrate.

By Carl Sunderman, Steve Signer

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed several new tools for evaluating roof support performance. A miniature data acquisition system (MIDAS) was developed that can collect readings from up to 16 strain gauges at regular time intervals and store the readings for later retrieval. Three LED lights change from green to yellow, then red, based on the reading levels and/or rates of change of rock movement. This feature can be used to warn miners of rock instabilities. The system can be used with any strain-gauged support (resin bolt, friction bolt, cable bolt) or with a newly developed rock strain strip (ROSS) developed by NIOSH to measure rock strain. A ROSS is grouted in a hole drilled adjacent to the rock support to be evaluated; the deformed shape of the ROSS provides anchorage on either side of the strain gauges. Data from both laboratory tests and field evaluations are presented that describe the capabilities of both the MIDAS and ROSS instruments.

By W. Hurst

What is entailed here is the extension of the sinzplified material balance formulas to encompass interference between oil fields. As previously reported, the ex-plicitness as so revealed for the cunzulative pressure drop as a function of all factors contributing to its change in the material balance equation, is now transcribed through the inter-conzmunicating aquifer to effect an increased pressure drop on an adjoining field by interference. Such is performed by mathematical analyses and the application of the Laplace transformations. What is accomplished is that the reiteration problems previously associated with interference studies are nullified, since volumetric changes for the fluids in situ are automatically adjusted by the explicitness so expressed, and what pertains to the superposition principle applies only to the impeded water drive upon a su.bject field, which is likewise incorporated in the over-all pressure drop that results. The mathematics treats with the rigorous solution of the problem, as well as with methods easily amenable to numerical interpretation by the practicing engineer. In all cases, however, what is deduced for areal extents, reveal interference between wells when time becomes large that further substantiate the analyses. Probably of equal significance, all variables and for/nation characteristics are accounted for. This applies to the differences in PVT analyses that occur from field to field and the physical parameters associated with the lithology of the reservoirs. The latter is deduced from a rigorous interpretation of the unsteady-state flow problem for sands of different permeabilities in series. Thus, what purports to be a trial-and-error calculation to include variations in sand conditions within the intercommunicating aquifer to define water drive has little importance compared to the designation of such paranzeters at the reservoir to constitute the essential criteria. INTRODUCTION In a recent publication, the reader has been introduced to the simplified material balance formulas,&apos; It has been shown that the complexities formerly associated for identifying and determining reservoir pressure in the material balance relationship can be resolved by treating with the Laplace transformations, the inversion of which reveals pressure as an explicit function of all factors contributing to its change. For an under saturated oil reservoir, this constitutes an integrated effect from the inception of production; and for a saturated oil reservoir, such represents a survey traverse. However, what is most important, for the first time we are able to express the pressure change in a reservoir directly to the oil, gas and water produced, and to the physical parameters of the formation, in the same manner that reservoir pressure has served in the past to define well interference — which opens up this avenue of endeavor for investigating interference between oil fields. The occurrence of interference is by virtue of the juxtaposition of two or more oil reservoirs producing in the same aquifer. Thus, in any one field, the extended production so incurred creates a pressure lowering in the field, as well as in the aquifer, which can now be transcribed by these simplified material balance formulas to the adjoining reservoir to observe the increased pressure change so induced. These effects are retroactive from field to field, to reveal a pressure drop far in excess of normal depletion to evidence the interference pattern that can result. Such is the purpose for the present undertaking — to develop the mathematical physics treating with this phenomenon of interference between oil fields, employing the simplified material balance formulas. Since Ref. 1 often will be referred to in the text, it is identified as "The Simplification", in the same connotation that another paper has been referred to as the "Laplace Trans-formation. However, the amount of material to be covered in these passages is substantial; therefore, the total emphasis will be placed upon developing these fundamental ideas treating with interference rather than attempting to offer work curves, which always can be prepared. For the practical application of these simplified material balance formulas that form the framework of the present development, the reader will find a comprehensive treatment in the Appendix of Ref. 1, illustrating a factual field example. In essence, what is proposed by this presentation is to make available to the practicing engineer a simplified means to treat with interference between oil fields, independent of the complex machine computations that have attended such undertakings in the past. As the problem unfolds, a common pattern will be discernible, whereby the many reiteration processes that previously required computing devices are eliminated.

By R. Karl Zipf, Christopher Mark

Highwall mining continues to grow in importance as a coal production method from U.S. surface mines. It may account for as much as 4% of the total U.S. coal production, according to one recent estimate. Analysis of Mine Safety and Health Administration (MSHA) accident and injury statistics shows that, overall, highwall mining has maintained an admirable safety record. Its fatality and injury rates are comparable to those for other surface mining methods, and are significantly lower than those for underground mining. No mining method is risk free, however. Highwall mining injuries have been associated with handling materials, slips and falls, machinery, powered haulage, and other types of incidents. But perhaps the greatest risk, to both personnel and equipment, is from ground control. The two most significant ground control hazards are rock falls from the highwall and equipment entrapment underground. Highwall Stability Ensuring highwall stability through proper ground control engineering is of paramount importance to safe highwall mining operations. The only fatality to occur during the last five years at a highwall mining operation was due to highwall collapse. There have also been numerous near-misses, several of which have involved extensive damage to equipment. In the central Appalachians, where the majority of highwall mining occurs in the U.S., hillseams are the most prominent geologic structures that affect highwall stability. Hillseams (or mountain cracks) are near vertical fractures in the rock that are formed in response to natural weathering and erosion of hillsides. They extend hundreds of feet down from the surface. They typically run parallel to the hillside, but they can also extend across narrow points or ridge lines. The hazard arises when rock slabs that form along the hillseams detach and fall away from the highwall face (See Figure 1). [ ] Unfortunately, it is impossible to control the location of hillseams or reliably detect their presence within a highwall. There are, however, a number of measures that can be taken to minimize the risk of failure associated with hillseams: Planning-Most operators choose to skip those areas of the highwall where a prominent hillseam daylights (See Figure 2). Existence of such areas is known for several weeks in advance of highwall mining; therefore, planning engineers can adjust the layout of highwall mining panels to locate barrier pillars within areas of questionable highwall stability. [ ] Inspection and monitoring-Daily inspection of the benches above the active highwall mining area is a prudent precautionary measure. A crack in a bench immediately above a highwall miner is shown in Figure 3. Simple displacement monitors may be useful for detecting movement along cracks that may precede a significant life-threatening failure. New tools, such as slope monitoring radar, may also prove useful in detecting motion of the rock slopes above active highwall mining operations. Good blasting practice-Most surface coal miners in the central Appalachians use pre-splitting and the familiar halfbarrels are routinely seen throughout the pits. Shorter delays along the face and longer delays between rows can direct more of the blast force parallel to the face, potentially doing less damage to the wall rock. In addition to pre-splitting, decreasing the burden, spacing and charge weight in drill holes close to the highwall will also decrease damage to the wall rock. Decreasing the highwall slope angle-Decreasing the highwall slope angle from 90° (vertical) to 70°-80°, especially in areas of known hillseam concentration, could eliminate the hillseam hazard (See Figure 4). Angled highwalls are routinely employed in many Midwestern surface mines and in some

By Sean Gallagher, William S. Marras, Alan S. Litsky, Deborah Burr

This paper describes a comparison of the fatigue failure responses of older versus younger lumbar spine cadaver motion segment specimens. These specimens were repeatedly subjected to loads simulating those experienced by the spine in lifting a 9 kg load in different torso flexion postures (0, 22.5, and 45 degrees of flexion). An older sample of 36 motion segments (average age 81 years + 8 SD) is compared with a younger sample of 18 motion segments (average age: 47 years + 9 SD) with respect to the number of cycles to failure and results of survival analyses evaluating the effects of flexion and bone mineral content with and without the younger data set. Compared to the older sample of spines, the younger sample exhibited many more cycles to fatigue failure in all the torso flexion conditions (10020 versus 8267 average cycles to failure in 0 degrees flexion, 7124 versus 3262 in 22.5 degrees flexion, and 3229 versus 263 cycles to failure in 45 degrees flexion). The increased cycles to failure in young specimens is likely due to the increased bone mineral content (BMC) in younger motion segments (30.7 g + 11.1 g per motion segment versus 27.8 + 9.4 g). Cox regression analyses modeling both flexion effects and BMC indicate that betas are similar when just older spines are modeled and when younger specimens are included in the analysis. Betas for survival analysis models with and without younger specimens generally show little change for flexion (2.716 versus 2.756 for 22.5 degrees [0 degrees referent], 3.926 versus 3.380 for 45 degrees [0 degrees referent]). Bone mineral content shows a similar protective effect in both models (Betas: -0.127 versus -0.087). Overall, comparison of the models indicate that risk ratios are similar for 22.5 degrees flexion, slightly increased for 45 degrees flexion and slightly more protective influence predicted for BMC in the combined sample versus the older sample alone.