Search Documents

By Kihong Park, Matthews C. Habjan, Arthur L. Miller

New Mining Safety and Health Administration (MSHA) regulations limit the mass concentration of airborne diesel particulate matter (DPM) or, more specifically, the concentration of elemental carbon (EC), in underground mines. The mine operators are responding by introducing a variety of controls to reduce DPM in the mines, potentially including the evaluation of new maintenance procedures to reduce underground mine vehicle emissions. There is currently a lack of an inexpensive and dependable method to directly measure the DPM concentration emitted from the vehicle tailpipe. To that end, this work demonstrated a simple field portable method for estimating the mass concentration of elemental carbon exiting the tailpipe of a diesel engine using a direct reading photometer. Simultaneous measurements of tailpipe exhaust were made with a Thermo Electron Personal DataRAM 1200 photometer (particulate mass concentration based on light scattering) and by analyzing PM2.5 and PM1.0 samples collected on quartz fiber filters using the National Institute of Occupational Safety and Health (NIOSH) method 5040 (mass concentration of EC via thermal-optical method). Results indicate surprisingly good correlation (R2 ) 0.97) of the two methods when the data are adjusted for relative humidity (RH) and corrected using an empirically generated calibration factor. Although preliminary, it may be possible to implement this method in maintenance shops to monitor emission trends and to compare emissions of various vehicles in a fleet. Such data will be useful for fleet planning to meet new air quality standards.

By R. E. Jenkins

The Bell Canyon member of the Delaware Mountain group has yielded quite a large number of fields in which completion and production problems have been numerous and complex. Reserves are difficult to estimate due to the problem of evaluating the formation water saturation, and the feasibility of water flooding is questionable. Extensive laboratory investigations were undertaken to determine if normally measured rock and contained fluids properties could account for many of the peculiar characteristics of the formation. A statistical study or routine core-analysis data was made. Capillary-pressure data were obtained by several techniques. Fresh-water and brine permeabilities were measured and relative permeabilities of oil, water and gas were determined. Some qualitative wetta-bility tests were performed, and the petrography of a few thin sections was studied. The results of this work are presented, with typical or average data shown for each test. The permeability -to- water characteristic of the Delaware was found to be abnormally poor. Correlations of laboratory and field performance data indicate high water saturations in much of the formation. Pore geometry is highly uniform. INTRODUCTION The Delaware formation has undergone extensive exploration and development in the past few years. This has resulted in the discovery of quite a number of fields—producing oil for the most part. A large percentage of the productive wells have produced water along with the oil. Often there is no apparent pattern for the percentage of water cut experienced. In several instances vertical displacments of over 200 ft have been established between communicating wells in which the formation appears to be about the same, yet the structurally high wells yield a much higher water cut than the lower wells. Drill-stem tests have contributed little to well completion because they nearly always show small amounts of water (usually mud filtrate), regardless of what is produced later in the life of the well. Other formation evaluation methods have had no more than limited success in indicating ultimate productivity. Consequently, predicting the type of fluid productivity of Delaware wells has been very difficult. Hydraulic fracture treatments are almost universal, and unstimulated Delaware wells have not exhibited the productivity that normally would be expected of wells with the specific permeabilities encountered. Some operators have indicated that their Delaware wells need frequent re-stimulation. The uncertainty of reservoir water saturations reported for the Delaware has made difficult the task of evaluating oil in place in the reservoirs and estimating primary recovery. The unreliability of this data also will cause feasibility studies for water flooding or other secondary-recovery methods to be problematical. Several opinions have been voiced to explain why the Delaware performs as it does. Chronically poor well completions, dynamic water and tilted water tables, capillary inequi-libria, peculiar relative permeability characteristics and oil-wetness are among the suggested reasons. The dual purpose of this paper is (1) to describe the principal rock characteristics, and (2) to present an evaluation of those characteristics so that approaches can be made to explain the irrational behavior of wells completed in the Delaware. STUDY OF ROUTINE CORE-ANALYSIS DATA A statistical study of routine core-analysis data has been made to relate fundamental rock properties and characteristics of the formation to well productivity. For the most part, well production data were obtained from operators and augmented by production data from commercial information services. Only data which were available in detail and which were considered to be accurate were used. The core data used were obtained on samples from the perforated or open interval only and, thus, may not always represent the total productive interval in a well. All the core-analysis data included in this study are from the Bell Canyon member of the Delaware and were obtained by "plug-type" techniques, as opposed to whole-core or full-diameter techniques. Porosity values were obtained by the summation-of-fluids technique, permeability values are air permeabilities corrected for slippage to an equivalent liquid permeability, and the oil and water contents were determined by means of a high-temperature downdraft retort. All the procedures used are discussed at length in Ref. I. The core-analysis data were sorted

By Tyler Rockley, Cara Rosen

Blasting at a granite quarry in eastern Maryland produces elevated air blast readings that can fall into the cautionary zone for the state of Maryland environmental regulations on a semi-regular basis. When designing blast patterns in this quarry, challenging geology creates rough and uneven blast faces that can be difficult to capture with 2D laser profiling fully. Utilizing several methods known to manage high air blast results like pattern adjustments, decking, and timing changes have not achieved consistent outcomes. Accurately capturing and modeling this geology is the key to controlling high air blast. 3D modeling and profiling by drone is the solution to understanding accurate face profiles and real minimum burdens. Using 18 months of blasting data and air blast results to establish a baseline, the comparisons between blasts designed with 2D profiling and blasts designed with drone 3D profiling show improvement in air blast levels. Additionally, shots with completed drilling were drone profiled to understand precise amounts of burden for each borehole. This 'audit' of a blast allows for custom loading of explosives, accommodating the amount of burden present on the blast face. 3Dprofiling is not a new tool in the blasting industry, but a drone alleviates some of the restrictions ground systems face. Controlling and managing air blast, as it pertains to face burdens, requires an understanding of those burdens from all angles. A drone provides that distinct level of insight. The results of this study indicate that drone profiling is managing the customer's air blast readings, allowing the customer to maintain their license to operate within the community.

By J. B. Cheatham, R. B. Paslay

Rock stresses and steady-state flow rates induced by the pressure gradient associated with the flow of formation fluid into a borehole have been analytically determined for a permeable, elastic material saturated with an incompressible fluid. In this analysis, the material properties and loading are considered to be symmetric about the axis of the borehole and independent of axial position. For Case I the material is assumed to have uniform permeability in the radial direction, whereas for Case 11 the permeability is assumed to have been reduced in a localized region adjacent to the hole by either normal well completion and production operations or deliberate plugging during air drilling. Results of a numerical example indicate that, in the absence of plugging, the rock shear strength must be approximately two-thirds the formation fluid pressure in order to prevent rock failure. The required rock strength is high for small radial zones of plugging and decreases as the region of reduced permeability becomes larger; however, a depth of plugging can be reached beyond which there is no real gain in strength, although the flow rate can be further reduced. INTRODUCTION During normal production of oil from a well, it is often desirable to increase the production rate of the formation fluid by increasing the pressure gradient through the formation adjacent to the borehole. Depending upon the magnitude of this pressure gradient and strength of the rock material, this production-rate increase can cause sloughing of the hole wall. In many cases, the production - rate increase can result in excessive sand production, increased wear of production equipment, lost production time and expensive workover jobs. In addition, the phenomenon of increased rock bit penetration rate with the use of a gaseous instead of a liquid drilling fluid has been observed in oilfield drilling operations and experimentally demonstrated by various investigators for several years. The improvement obtained by employing this technique can be quite significant and offers apromising method for reducing drilling costs. However, air drilling is currently limited to geographical locations where high-capacity water-bearing formations are not encountered. This limitation has prevented widespread adoption of air-drilling techniques, because the water influx into the borehole interferes with efficient removal of the drilling cuttings and usually results in a condition such that the bit becomes "balled-up" or stuck in the hole. In an attempt to remove the water - intrusion limitation from air drilling, various chemical and mechanical water shut-off methods have been proposed. Goodwin and Teplitzl suggested one such proposal whereby the permeability of the water-bearing rock structure was reduced in the vicinity of the borehole. Although the development of a shut-off method based upon this approach would certainly be welcomed by the oil industry, it is conceivable that, under certain conditions of the pressure gradient, strength of the rock material and depth of the modified permeability zone, a stress field can be created that will result in an unstable hole. As part of their study, an analytical solution is given for stresses in an idealized model of a hole and the surrounding rock material. The purpose of the present study is to extend the analysis of Goodwin and Teplitz to gain more insight into the details and consequences of excessive production rates and formation water shut-off. In particular, simplified models of these problems have been analytically examined, which makes possible the evaluation of the type of stress fields that can be anticipated as a result of these production and drilling practices. Both problems solved concern the determination of the steady-state volume flow rate of the formation fluid and the resulting steady-state stress and displacement distribution in a hollow, cylindrical configuration. The cylinder of Case I, corresponding to the production-rate problem, consists of a material with a constant permeability from the inside surface to the outside surface; the cylinder of Case 11, corresponding to the water shut-off problem, consists of a material with a constant permeability from the inside surface to an intermediate concentric cylindrical surface and a second constant permeability from the intermediate surface to the outside surface-

By Pradip

Bastnaesite, a rare-earth fluocarbonate, was separated from associated calcite and barite gangue minerals in the Mountain Pass, CA rare-earth ore beneficiation plant by froth flotation using fatty acids (tall oil) collector, lignin sulfonate depressant and soda ash modifier after high-temperature (steam) conditioning with reagents. Starting with a feed grade of 7.6% REO, concentrates having a grade of 65% REO can be produced at a recovery of around 80%. A detailed investigation consisting of Hallimond tube microflotation experiments, bench-scale tests with a laboratory Denver flotation cell, and predesigned plant campaigns was made to delineate the underlying surface chemistry involved in this separation and to develop an alternate reagent scheme to enhance the selectivity of separation for this ore. Our results clearly demonstrate the superiority of alkyl hydroxamates to the conventional fatty acid collectors that were being used in the plant. Our study also indicates the possibility of achieving the desired selectivity with alkyl hydroxamates even at room temperature, thus obviating the need for steam conditioning. A critical review of the literature on rare-earth mineral flotation suggests the possibility of designing a more selective reagent combination for the beneficiation of Mountain Pass rare-earth ore, using a methodology based on ab initio molecular modeling computations.

By H. D. Outmans

A method has been developed for determining the relative water wet-tability (fraction of the surface wet by water) of porous media. This method involves the adsorption of methylene blue dye from an aqueous solution onto the solid surfaces of rock contacted by the injected dye solution. Experiments on Berea snndstone cores have shown that water-wet cores adsorb a large amount of dye from solution. In oil-wet cores, however, the injected aqueous dye solution is prevented from contacting the adsorptive surfuces by a film of oil and virtually no dye is adsorbed. This method was tested by experiments on mixtures of water-wet and oil-wet sand. Using the dye adsorption method, it was possible to determine quantitatively the fraction of water-wet and oil-wet sarzd in such mixtures. The dye adsorption test is readily applied to determinitrg the relative water wettability of fresh oilfield cores. The cores are not extracted before testing. Observed values of the wettability of field cores tested to date have varied from 100 to 6 per cent water wet. INTR OD UCTIO N Recent articles1 ' have emphasized the important role that wettability plays in almost all phases of reservoir rock behavior. It has been shown that wettability has a profound effect on the interstitial water saturation, residual oil saturation, capillary pressure, relative permeability, waterflood behavior, and resistivity index of oilfield cores. A quantitative investiga- tion of the effect of wettability on these core properties is severely handicapped by the lack of a simple technique for measuring the wettability of a porous medium. If such a technique were available, it would provide investigators with a means of gaining insight into the distribution of phases within a core. A number of qualitative methods of estimating wettability are known. These include contact angle measurements, flotation tests and studies of displacement pressure: imbibition7 and relative permeability data.' Using these tests, it is usually possible to classify a core as water-wet, oil-wet, or some intermediate degree of wettability. One recently proposed method involving measurement of nuclear magnetic relaxatione offers promise of determining quantitatively the fractional wettability of cores. The equipment is rather elaborate and necessary treatment of the cores before testing probably alters the natural wettability. This latter point also applies to most of the cited qualitative methods. This paper presents a new technique for determining water wettability of cores; it is based on measurements of the dye adsorption capacity of the core. This method has the advantage of requiring relatively simple equipment and involves minimum handling of the core before testing. It is important to distinguish between the various concepts of wettability referred to in the literature. The term "wetting" is defined by Bartell as that phenomenon which occurs when a solid and liquid phase come in contact in any manner so as to form a solid-liquid interface. A preferentially water-wet solid is defined by Jennings in terms of the advancing contact angle in the solid water-oil systems. Brown and Fatt regard fractional wettability as the fraction of the total surface area that is preferentially oil-wet or water-wet. However, none of these definitions adequately describes the type wettability measured by the dye test. This calls for the introduction of a new term, "relative water wettability", which we define as the fraction of the total surface area of a core contacted by injected water. DESCRIPTION OF METHOD The ability of a porous medium (especially the clays) to adsorb large quantities of surfactants, dyes, etc., is well known. It is reasonable to assume that a substance can be adsorbed from solution onto a solid surface only if the solution contacts the surface. In this connection Shapiro" has shown by experiments on silica gel that completely dry gel will adsorb methyl red dye from a benzene solution. On the other hand, if a film of water more than several molecules thick is present on the silica gel, the adsorption capacity of the gel for the dye is drastically reduced. Thus, a study of the dye adsorption capacity of cores should give some clue as to the fluid distribution on the surface of the core. TEST OF METHOD As a qualitative check on this theory, dye adsorption tests were run on similar Berea sandstone cores (Table 1, Cores 1-5). Cores saturated initially with water and flooded with 0.01 per cent aqueous methylene blue adsorbed 0.58 mg dye/gm of core. Similar cores saturated initially with water, driven to irreducible water with oil, and then flooded with the same dye solution also adsorbed 0.58 mg dye/gm of core. Another core, treated with a 5 per cent Dri-Film solution, dried and saturated with oil (Soltrol) adsorbed no dye when the dye solution was injected. These tests confirm

By Sung Jin Han

Magnesia-based refractory is generally used in an electric arc furnace (EAF) due to its relatively high corrosion resistance and strength at high temperatures. However, the magnesia refractory is attacked by EAF slag and thus the lining life continuously decreases. Thus, it is significant to identify the interfacial reaction between magnesia refractory and FeO-rich EAF slags. In the present study, the influence of FeO-rich slag on the corrosion behavior of MgO refractory was evaluated. The (Fe,Mg)Oss layer was observed at the slag-refractory interface and its thickness increased with increasing content of FeO in the slag. The specific reaction phenomena and formation behavior of (Fe,Mg)Oss layer were evaluated by thermochemical computing program, FactsageTM7.0.

The compliance sampling method for coal mine dust in the United States has not changed appreciably in the last 30 years. A call for more frequent sampling with immediately available results is leading to new instruments that may supplement or replace the existing sampler. This report discusses two such instruments that provide immediate results of dust levels. The first, called the Respirable Dust Dosimeter (RDD), is designed to supplement the existing U. S. cyclone compliance sampling method. It uses the pressure drop across a filter to provide an inexpensive screening type of measurement. The RDD has been tested in the laboratory and a limited number of coal mines. Side by side testing has compared the RDD performance with personal coal mine samplers in triplicate area sample measurements. Results show that the differential pressure of specific filtration media can be an effective surrogate for respirable mass. Data show that there is a dependence on coal type and an effect of relative humidity. There also appear to be two distinct responses related to coal type. For specific coals the coefficients of determination, R2, are better than 0.9. For general use the detector tube, using laboratory generated calibration curves, can be used to estimate respirable dust levels. However, a calibration to a specific coal type may substantially improve the accuracy. Another sampler in development is called the Personal Dust Monitor (PDM). Designed to give compliance quality accuracy, the PDM uses the frequency change of a vibrating element to measure dust and give immediate feedback of results. Results of laboratory comparison of the prototype PDM sampler to personal gravimetric samplers indicate R2 values of better than 0.99 for three different coal types. Work is in progress to package the components into a person-wearable unit combined with a cap lamp system with a total projected weight of less than 1.4 kg (3 lbs).

By D. M. Beeson, G. D. Ortloff

Water-propelled banks of carbon dioxide recovered both high- and low-viscosity crude oil substantially in excess of that recovered by water flood in linear flow model experiments. The increase in oil recovery is explained by oil swelling and viscosity reduction. Additional oil was recovered by solution gas drive at the end of the carbon dioxide floods when the model systems were depres-sured. This study was an investigation of the use of a water-driven carbon dioxide bank to recover crude oil. Techniques involving the injection of carbon dioxide have aroused con-siderable interest in recent years among methods considered for increasing oil recoveries. A number of investigators have studied the process in the laboratory1-' and in the field.7,5 Laboratory studies referenced indicate that carbon dioxide in conjunction with water flooding recovers more oil than does water flooding alone. These re- ports diverge widely, however, in stating magnitude of improvement. We believed that a water-driven carbon dioxide bank would increase recovery of crude oils by two mechanisms: viscosity reduction and oil swelling. Due to reduction in the oil viscosity caused by solution of carbon dioxide, displacement efficiency should be improved. In addition, the residual oil should be highly swollen by the carbon dioxide held in solution. Thus, the final residual oil saturation, in terms of stock-tank oil, would be lower than in the absence of carbon dioxide. To test this hypothesis, experi-

By C. P. Lazzara, R. A. Franks, G. F. Friel, J. C. Edwards, J. J. Opferman

A series of four coal combustion experiments was conducted at the National Institute for Occupational Safety and Health's (NIOSH) Pittsburgh Research Laboratory (PRL) in the Safety Research Coal Mine (SRCM) to evaluate the response of fire sensors to a small 0.61 m square smoldering coal fire which transitions to flaming combustion in the presence of diesel emissions. An optical path smoke sensor alarmed earlier than a point type diffusion mode ionization smoke sensor which alarmed prior to a CO alert value of 5 PPM above ambient. The presence of steady state diesel emissions resulted in a decrease in the optical smoke sensor analog output voltage signal by less than 1.4 pct for the three coal fire experiments in which a diesel engine was operating, whereas the ionization smoke sensor output decreased between 10.8 and 26.7 pct after the initial surge of the diesel engine. A commercial diesel discriminating fire sensor did not alarm for a fire in the one experiment for which it was used. The results of the experiments demonstrated that an optical path smoke sensor might be used to detect a coal fire under the experimental conditions considered of starting a diesel engine followed by a slowly developing coal fire.

By F. H. Deily, D. S. Rowley, R. J. Howe

By T. Gupta, T. Ghosh

Rare earth elements (REEs) and their compounds are essential in a multitude of mundane and sophisticated applications such as renewable energy technologies, catalysts, medicine, and defense applications. The global supply deficit could be attributed to the destabilization of REE market that has, as a result, incentivized indigenous production of REEs. Cost-effective and environmentally benign opportunities are being explored for the production of REEs from non-conventional mineral sources including coal and coal by-products to stabilize the supply chain. Coal from Healy coal mine and Wishbone Hill deposits in Alaska have been quantified for REEs and were found to possess elevated total REE concentrations as compared to world average levels (60– 70 ppm). The objective of the study was to concentrate the REEs in the froth phase by froth-flotation of the fine size fraction (< 75 μm). A Box-Behnken design of experiment was employed to ascertain the main and interaction effects of operational parameters on response variable by analyzing 3D response surfaces. Experiments were carried out to maximize REE recovery and concentration by modeling and optimization of three operating variables (frother dosage, pulp density (% solids), and collector dosage). Based on the results, the optimum flotation conditions for maximum recovery at an elevated concentration of REEs in the froth fraction was obtained at 4.2% solids and 32.7 ppm of frother dosage for Healy sample and 10% solids and 37.9 ppm of frother dosage for Wishbone Hill coal sample. The quadratic relationship between the input and response variable was found to be independent of collector dosage suggesting good surface hydrophobicity and floatability of the two coal samples.

By A. T. Iannacchione

Designing coal pillars to provide resistance against overburden and gob loads has long been an aim of rock mechanics engineers. This requirement has become more imperative as greater overburdens are encountered and when mining in stiff coal-bearing strata. Current design procedures rely on theories of coal pillar behavior that take into consideration a common hypothesis. This hypothesis states that the elastic core is surrounded by an inelastic yield zone. The distribution of stress at low-to-moderate pillar loads has been effectively defined by this hypothesis. However, it suffers greatly when applied to large width-to-height (w/h >lo) coal pillars under considerable overburden (>500 m) . In these situations, the hypothesis says the elastic core can achieve unrealistic stress states giving the pillars extremely high calculated strength. A growing body of field studies has shown this is not the case. It has become clear that same other mechanism must be involved. It is the purpose of this paper to discuss the importance of an interface slip mechanism between the coal- bed and the surrounding strata in controlling the extent and pattern of stresses and deformations in a coal pillar.

By Emery Chilton, Charles Taylor, Mark Senk, Linda McWilliams

Three-axis ultrasonic anemometers are used to study airflow in the NIOSH ventilation gallery where ventilation in an underground mine is simulated. In this study, performance characteristics of this anemometer are evaluated and the effects of sensor orientation and sampler location on flow readings are examined. The study results provide guidelines for more effective use of the ultrasonic anemometers in the ventilation gallery.

By Steven J. Schatzel, Robert B. Krog

Frictional ignitions are defined as the ignition of a flammable mixture of methane and air that is initiated by frictional heating. Ignitions created through the addition of energy from open flames and exposed electrical circuits are not included in this analysis. Energy released in a roof fall that creates a spark and ignites a methane mixture would be considered a frictional ignition. Frictional ignitions represent the majority of all ignitions in underground coal mines. Over the study period of 1983 to 2005, a total of 1993 ignitions were reported in underground bituminous coal mines in the United States, of which 1589 were frictional ignitions. Reportable ignitions to the Mine Safety and Health Administration (MSHA) are any unintentional occurrences of flame underground regardless of duration. Frictional ignitions were reported in 155 mines and 13 states. Continuous miners represented the largest source for frictional ignitions with 1090 (68.6% of all frictional ignitions). Longwall mining operations represented the highest concentration of frictional ignitions during this study period with 1365 frictional ignitions (85.9% of all frictional ignitions). The 17 mines with the most frictional ignitions were all longwall mining operations and had 1130 frictional ignitions (307 from the shearer) that represented 71.1% of the total. In 1983, mines with frictional ignitions represented 6.9% of operating underground mines and 36.6% of total underground coal production. The percentage of operating underground mines with frictional ignitions and their total production has increased steadily and in 2005 represented 9.8% of active mines and 46.2% of underground coal production. The three coalbeds with the highest number of frictional ignitions (Blue Creek, Pittsburgh No 8, and Pocahontas No 3) had 1049 ignitions that represented 66.0% of all frictional ignitions. The three states with the highest number of frictional ignitions were Alabama (710), Virginia (247), and Pennsylvania (242) that represented 75.5% of the total. Frictional ignitions peaked in 1991 with a high of 114. In 2005, only 34 frictional ignitions were reported. If only frictional ignitions that occur at the face are considered, there have been no fatalities since 1983. Since this time, there were 33 ignitions that caused 53 workers to lose a total of 2912 working days. When including ground falls, then there have been four frictional ignitions with one incident causing two fatalities and injuring eight workers. From 1983-1991, underground productivity and the number of frictional ignitions increased. However, productivity continued to increase from 1991-2000 while total frictional ignitions fell, thereby disproving this connection between productivity and frequency of frictional ignitions. Ninety percent of all frictional ignitions occurred in underground coal mines that liberated more than 393 L/s (1.2 MMcfd million cubic feet per day) of methane through the main ventilation system. Although methane production is not the determining factor for the occurrence of frictional ignitions, it is a good indicator of the anticipated frequency.

By Eric J. Foell, Hjalmar Thiel, Gerd Schriever

Environmental studies for the mining of polymetallic nodules (PN) from the deep sea may be traced back for some 35 years.

By L. Xia

Sodium silicate(s), also known as “water glass”, are one of the oldest and most widely used industrial chemicals. Its first use in Canadian operations can be traced back to around 1925, which coincided with early use of xanthates in mineral flotation. Silicate functions as a sulphide and non-sulphide gangue mineral dispersant, depressant and modifying reagent in grinding and flotation operations. It is believed that soluble sodium silicate promotes selectivity of value added sulphides against gangue minerals, resulting in both grade and recovery improvement. This paper seeks to link improved grade/recovery to the interaction characteristics of minerals and the sodium silicate. A systematic study was performed with individual mineral species, an artificially designed model ore and the feed ore from a copper flotation operation. The function of sodium silicate was evaluated in the context of colloidal chemistry and linked to mineral surface chemistry. Measurement of pulp rheology and mineral zeta potential identified that sodium silicate works as a dispersant. The dispersion is accomplished by increasing a mineral’s net surface charge, resulting in a change in slurry viscosity. Bench scale laboratory flotation tests suggest that better dispersion leads to a diminished interaction of chalcopyrite with gangue. The improved Cu grade and recovery then are likely in response to an increased accessibility to collector along with a linked increase in particle bubble attachment resulting in better separation efficiency. ToF-SIMS surface chemical analysis of the flotation samples found a higher proportion of sodium silicate on minerals from the flotation tailings relative to the concentrates. Moreover, attachment of sodium silicate appears to be mineral specific; the data indicates that sodium silicate favours the surface of gangue phases over the value sulphides.

By Krishna Parameswaran

This paper illustrates sustainability considerations in copper hydrometallurgy using examples of practices at ASARCO LLC, an integrated U.S. primary copper producer. Using the classic Brundtland Commission development of sustainable development, i.e., “development that meets the needs of the present without compromising the ability of future generations to meet their own needs,” the paper discusses how copper hydrometallurgical processes can be sustainable. The examples used to illustrate sustainable development and related concepts include: water conservation opportunities in milling and leaching operations; implementing green chemistry and promoting product stewardship in the electrorefining of copper.

The February General Meeting of the Branch was held at the St. Helena Club on Wednesday, 19th February, 1969. Present were: Twelve members: Mr J. G. Kirchner (Chairman of the O.F.S. Branch), Messrs J. N. Saunders, N. A. Honnet, L. O. W. Leimer (Committee Members), Messrs R. C. Espley-Jones, J. W. Wilson, A. T. Lewis, A. von Holdt, L. J. Thorne, C. Mostert, V. O. Steed, H. H. Schellhorn. Nine Associate Members: Messrs E. R. Penny, G. T. C. Emere, M. Forster, K. Pearce, R. B. Sutherland, D. E. Couperthwaite,A. H. Edwards, M. D. de Lange, G. ,R. Still. Four Graduates: Messrs M. H. Smith, N. Mayer, T. R. Stromsoe, T. A. Ward. Four Affiliates: Messrs D. S. Robinson, L. D. Hulley, R. B. Smith, R. L. Soll11s.One Student: D. R. Fleming. Twenty-three Visitors. Total present: 53. Apologies were received from Messrs C. R. Netscher, A. Leger and V. C. Barnes. MINUTES OF PREVIOUS GENERAL MEETING The minutes of the General Meeting held on 15th November, 1968 and which were published in the February Journal, were taken as read and their adoption moved by Messrs J. N. Saunders and N. A. Honnet. There were no matters arising from the minutes. GENERAL BUSINESS The Chairman reminded members of the forthcoming visit by the Branch to the Dudfield Works of the Anglo-Alpha Cement Company, to take place on Wednesday 16th April. TALK ON ROCK MECHANICS The Chairman called upon Mr J. W. Wilson to address the meeting on the subject of the practical applications of rock mechanics to mining. Mr Wilson used a slide projector to present his subject in a most interesting and instructive manner which eventually resulted in much useful discussion taking place. The Chairman then called upon Mr A. von Holdt to thank the speaker. CLOSURE After thanking the speakers, the Chairman thanked members and visitors for their attendance and closed the meeting at about 10 p.m., after which refreshments were served.