Search Documents

By J. C. Bartlett

As American students of mining, philosophy, philology, music, history, or art have found it necessary or highly advantageous to supplement their course of study at home by a residence of some years at a foreign university, so, ever since mining has been practiced in this country in any other than a rude and wasteful manner, many American students of mining have sought in London or Paris, but chiefly in the Academy of Freiberg, Clausthal, or Berlin, such infor-

NEW BOOKLET FOR POTENTIAL ENGINEERS A new booklet "Professional Careers in Engineering" for issue to high school students who are considering engineering as a profession has been prepared for general distribution. The booklet is intended to help high school students to decide whether a career as a professional engineer would appeal to them, and to tell them how to set about becoming a professional engineer. Copies of the booklet may be obtained free of charge by writing to: The Federation of Societies of Professional Engineers, P.O. Box 5907, Johannesburg.

By S. Holtermann

Through the process of Riverbank Filtration (RBF), the Louisville Water Company plans to obtain a higher quality source of water for their B.E. Payne Water Treatment Plant (WTP) by means of four collector wells located in the alluvial aquifer along the bank of the Ohio River. The collector wells are connected to a 2,850 L/s (65 mgd) pumping station by a 2,362 m (7,750 ft) long, 3 m (10 ft) finished diameter tunnel located in limestone and shale bedrock, which is approximately 45 m (150 ft) below the surface. High tunnel boring machine (TBM) production rates were achieved in this moderately weak bedrock; most of the tunnel only required support in the crown. An unanticipated water-bearing fault and unanticipated ground behavior proved challenging and required quick thinking to minimize impacts to construction. Tunneling conditions are discussed in detail, together with the methods used for overcoming the groundwater and ground behavior challenges. The tunnel is expected to be completed in April 2009.

By Michael J. Sapko, Samuel P. Harteis, Eric S. Weiss

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) recently conducted full-scale explosion experiments; these experiments evaluated the strength characteristics of various seal designs used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests were conducted within the multiple entry section of PRL’s Lake Lynn Experimental Mine (LLEM) employing the only currently accepted test method endorsed by the Mine Safety and Health Administration (MSHA) for seal design in American mines. These explosion tests are labor-intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. Therefore, the PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in-situ testing of seals in an operating mine. Two chambers within LLEM and one within the Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from tests in these chambers compare favorably with those from the large-scale explosion tests in the multiple entries. Preliminary size-scaling relationships for predicting the strength of standard seal designs as a function of entry size is also presented. In addition to testing seal designs at the required 20 psi static pressure level, the new facilities also allow for the determination of the seal’s ultimate failure pressure. This new approach shows promise as an alternative evaluation method for improving mine sealing technologies which, in turn, will enhance the safety of the underground personnel.

By R. P. Rothwell

AT this our first meeting I beg to call the attention of the members of our Institute to what is certainly a question of the greatest possible importance to the industries we represent; and more particularly to the welfare of the coal and iron trades: I refer to the enormous waste of coal in mining and in its preparation for market, as now practised in our anthracite coal-fields. I t is a fact which many of you can certify to, that we are wasting fully me-half of all the coal in the veins we are now working, and there are cases, which might be mentioned where this proportion, immense as it is, has been greatly exceeded. The popular belief that our deposits of anthracite coal are "practically inexhaustible," is very far from being founded on facts. On the contrary, supposing the present rate of increase in the production to be maintained, it is probable that a maximum yield for our coal-fields would be attained in about fifteen years ; there are in fact some of our smaller basins where the principal veins are nearly exhausted and the production has already attained its maximum. There are others, again, where the depth attained-and it must be borne in mind that we commenced working at the surface outcrop moderate though it is (scarcely ever reaching eight hundred feet), has so increased the cost of mining as to imperil the capital invested, and though it requires but little foresight to predict the time when the difficulties of mining will be very considerably increased by reason of the greater depth, greater quantity of water, fire-damp, and other fruitful sources of cost, yet, ignoring these recognized facts, we continue to waste more than one-half of the coal where it is obtained with the least danger, expense, and trouble, that is, near the surface-either above water-level or at a moderate depth . below it. The inspection of almost any accurate mine map will satisfy you that, on an average, we leave fully one-third. of the coal in the ground as pillars to support the roof; in some places more than one-third thus remains, while it is very rare that less than one quarter is left. In almost every case this coal is absolutely lost, for it will very rarely pay to reopen gangways and lay roads to it after that portion of the mine has been abandoned. Is it necessary in all cases to support the roof, and where it is, may not some artificial

By James Vaughan

Australia is a major miner of ore that requires hydrometallurgical processing. According to the 2016 US Geological Survey Minerals Commodities Summaries, the country is 1st for aluminium (bauxite) and lithium, 2nd for gold, zinc and cobalt, 4th for nickel and silver, and 6th for copper mining, not to mention its wealth in coal and iron ore. In this paper, examples of recent Australian hydrometallurgical activities are summarised. Then, selected research projects from the University of Queensland hydrometallurgy research group are profiled. The projects profiled are related to fundamental aspects of processing bauxite with organics and reactive silica as well as the development of a synergistic hydro- and pyrometallurgical process for copper. The process context and motivation for the research is introduced, key results are highlighted with the associated relevant references.

By Joseph C. Zelanko, Anthony T. Iannacchione

One of the most difficult and longstanding engineering problems associated with coal mining is the catastrophic failure phenomenon known as coal mine bursts (known in the United States as bumps). For more than 70 years, researchers and practitioners have attempted to determine whether this destruction observed underground is caused by stress conditions within the coal pillar or from distant seismic sources in the mine roof and floor strata. The role of confinement and the extent of failure in solid pillars and panels have also proven difficult to define. These are important issues, since control solutions need to be based on a fundamental understanding of the problem. Obsenations by U.S. Bureau of Mines researchers over the last decade have helped to clarify certain aspects of these issues. Microseismic sensors and geomechanic field measurements have located areas of excess energy release, identified stress conditions in coalbeds close to failure, and recorded the response of mine structures prone to bursts. In the present study, data available for a range of U.S. bursts were considered in an effort to evaluate both common and distinctive features. Although the attempt revealed little commonality, encouraging results were produced by categorizing coal bursts by source mechanisms. When a coal burst is thus categorized, differences in environmental factors-such as geology, stress fields, and mining methods-are highlighted, and viable control strategies are readily recognized.

By Peng Gao

Coal-based reduction followed by magnetic separation is an innovative technology used in processing refractory iron ores. Given that size is essential to the separation of the metallic iron from the gangue, the morphology of metallic iron particles and their evolution during coal-based reduction are investigated in the present work. The size of the metallic iron particle increased from 128.76 µm to 565.70 µm when the reduction time increased from 20 min to 60 min at 1,225° C and C/O (i.e., the amount of coal addition in terms of the gram-atomic ratio of the fixed carbon in the coal added to the combined oxygen in iron oxides) of 2.5. Based on our microstructural and metallographic analysis, the iron ore reduction process can be divided into three stages: (1) metallic iron particle formation, (2) iron oxide reduction and metallic iron assembly and (3) metallic iron particle growth. Almost all iron oxides are reduced to metallic iron in the second stage. These newborn metallic iron particles are energetically active and able to assemble and grow, and are eventually separated from the gangue. The large metallic iron particles benefit the subsequent magnetic separation process.

By W. W. Whitaker, C. W. Manry, R. H. McLean

In an eccentric annulus, cement may favor the widest side and bypass slower-moving mud in the narrowest side. Tendency of the cement to bypass mud is a function of the geometry of the annulus, the density and flow properties of the mud and cement and the rate of flow. Bypassing can be prevented if the pressure gradient protluced from circulation of the cement and buoyant forces exceeds the pressure gradient necessary to drive the mud through the narrowest side of the annulus at the same velocity as the cement. In the absence of buoyant forces, one requirement for this balance is maintenance of the yield strength of the cement greater than the yield strength of the mud multiplied by the maximum distance from the casing to the wall of the borehole and divided by the minimum distance. If the yield strength of the cement is below this value, bypassing of mud cannot be prevented unless buoyant forces or motion of the casing significantly aid the displacement. INTRODUCTION Successful primary cementing leaves no continuous channels of mud capable of flow during well treatment and production. Prevention of channels requires care. Tep-litz and Hassebroek provide evidence of channels of mud after primary cementing in the field.' Channeling of cement through mud in laboratory experiments has also been reported.'-' Recommendations for improving the displacement of mud include (1) centralizing the casing in the borehole,'-" 2) attaching centralizers and scratchers to the casing and moving it during displacement,18 "3) thinning the isolating the cement by plugs while it is circulated down the casing,%( (5 establishing turbulence in the cement," and (6) holding the cement slurry at least 2 lb/gal heavier than the mud and circulating the cement slurry at a very low rate of flow.' Although much has been written about the above parameters, the relative importance of each has not been well defined. In this investigation, the mechanics of mud displacement are described through results from analytical models and experiments. The model chosen — a single string of casing eccentric in a round, smooth-walled, impermeable borehole — is analagous to casing centralized in a borehole which is not round and to placing more than one string of casing in a borehole. In each, some paths for flow are more restricted than others. A fluid flowing in the borehole may seek the least restricted, or most open, path. This tendency for uneven flow can lead to channeling of cement through mud unless preventive measures are taken. The analytical models describe channeling and give means of balancing the flow. Experimental data test the analytical models and illustrate effects of motion of the casing, differences in density and mud's tendency to gel. Results are encouraging. Piston-like displacement of mud by an equal density cement slurry is possible through proper balance of the flow properties of the mud and cement slurries to the eccentricity of the annulus. The more eccentric the annulus, the thicker must be the cement relative to the mud. If proper balance is not achieved. bypassing of mud by cement cannot be prevented without assistance from motion of the casing or buoyant forces. Increasing the rate of flow can help to start all mud flowing but cannot prevent channeling of cement through slower moving mud in an eccentric annulus. Thinning the cement slurry tends to increase channeling although the extent of turbulence in the annulus may be increased. Description of flow in an eccentric annulus begins in the next section. It is assumed that (1) the casing is eccentric and is stationary, (2) the mud and cement slurries have the same density and (3) the gel structure of the mud has been broken and the mud and cement follow the Bingham flow model. Effects related to these restrictions will be discussed. FLOW PATTERNS SlNGLE FLUID IN ANNULUS Flow of a single fluid through an eccentric annulus is illustrated in Fig. 1. Part A shows laminar flow of a Newtonian fluid. This distribution of flow was calculated by Piercy, Hooper and Winney.' In fully developed turbulent flow, the velocity distribution around the annulus is less distorted, but the flow still favors the widest part of the annulus Parts B, C and D of Fig. 1 are a qualitative representation of the flow of a Bingham fluid. The yield strength of the fluid increases the severity of bypassing compared to Newtonian flow. At a very low rate of flow, all flow is confined to that portion of the annulus which has the minimum perimeter-to-area ratio. The fluid shears on the perimeter of that area when the pressure gradient multiplied by the area just exceeds the yield stress of the fluid multiplied by the perimeter. Whether or not the minimum perimeter-to-area region encompasses all of the annulus or only a part (as shown in Part B) depends on the geometry of the annulus. If only a part begins to flow, increasing the rate of flow increases the area flowing until finally there is flow throughout the annulus.

By Michael Zachariah, Art Miller, David Kittelson, Gib Ahlstrand

This report describes an investigation in which we used iron-doped diesel fuel to generate metal-bearing diesel particles and a subsequent analysis of the particles using transmission electron microscopy (TEM) and energy-dispersive spectroscopy (EDS). For this study, DPM was generated by a 1.5-L diesel engine and the fuel was doped with ferrocene to enhance the level of iron in the system. The exhaust particles were collected on TEM grids and analyzed using the Philips CM12 TEM/EDS instrument. Results show that when the iron-to-carbon (soot) ratio (Fe/C) in the engine is low, the exhaust particles have morphologies similar to those for the undoped case, but at a threshold Fe/C value of 0.013 (for this engine), homogeneously nucleated metallic nanoparticles are formed and begin agglomerating. The number and size of these nanoparticles increase with level of doping. Metal-bearing particles that span a wider size range are also formed. Agglomeration of metallic and carbon particles is observed in two distinct modes: attachment of iron primary particles (5–10 nm in diameter) to carbon agglomerates, and coagulation of iron agglomerates (20–200 nm in diameter) with carbon agglomerates. Results of this work imply that as new engine technologies reduce soot levels in the engine and/or levels of trace metals in the fuel are increased, the generation of metallic nanoparticles may ensue, creating a potential health concern. Keywords: Nanoparticles; Particulate emissions; Metallic particles; Metal emissions

By Scott Rosenthal, Kyle Murphy

This paper discusses the trials and tribulations of obtaining Velocity of Detonation (VOD) readings in small diameter blast holes in an underground mine. Montana Technological University (Montana Tech) obtained a time-domain reflectometer (TDR) type VOD monitoring unit. Purchase of the VOD monitor was justified on verifying explosives performance used in Montana Tech’s practical underground mining class and provide a teaching aid for the school’s rock fragmentation class. Before demonstrating the unit to students, we figured we better learn how to use it first so we give the students an appropriate experience. Our first learning was in obtaining the correct coaxial cable for the VOD monitor and how to properly terminate the cable. Once the cable was on-site and terminated, VOD testing could commence. Use of the VOD monitor was tested underground in small diameter holes (1.5-inch, 38 millimeter) pneumatically loaded with ANFO. After a few failed trials, and follow-up discussions with the supplier, VOD readings were obtained for the ANFO loaded holes. Additional readings were obtained for a pre-split product and detonating cord to satisfy our curiosity that the unit was performing as specified by the manufacturer. This paper will share our learnings in the hopes that others can benefit.

By Lisa Steiner, Robin Burgess-Limerick

Working with or near underground coal mining equipment is hazardous because of the multiple sources of energy and adverse environmental conditions. Of the 4169 injuries reported to Coal Services during the three years to June 2005,447 were associated with continuous miners, 232 with LHD (load-haul- dump) vehicles, 140 with shuttle cars, and 140 with personnel transport - a total of 959, or 23% of all injuries reported during the period. An analysis of the injury narratives accompanying these injury claims highlights a number of opportunities for controlling injury risks. Using the frequency of reported injuries for the prioritisation of risk control strategies has limitations because of the tendency to underestimate the importance of relatively uncommon but potentially high consequence events. Injury reports also underestimate the contribution of risk factors such as whole body vibration, which have a long-term cumulative contribution to an elevated risk of injury. However, taking these limitations into consideration, the results of the injury narrative analysis suggests the following hazards as the highest priority for elimination or control: • handling continuous miner cable • strain while bolting • slipping off continuous miner platform • inadvertent or incorrect operation of bolting controls, and operation of controls while a person is in a position of danger • hitting potholes or other roadway abnormality • collisions while driving underground vehicles

By C. E. Kemp, A. B. Dyes

Results of a field research project on the thermal recovery of oil by movement of a combustion front are presented. This field test was conducted in the South Belridge field, This The war paitern was a Southsing1e 2.5-acre five-spot pattern in the 700-ft deep Tulare sand. Results of this project indicate the technical feasibility of producing high viscosity, low-grallity crude oils by thermal means. It was demonstrated that heavy oils could be moved rapidly over considerable distances by thermal drive, and that high percentage recoveries of oil could be effected. The bulk of the oil recovery came after arrival of the burning front at a production well. However, rapid corrosion and high-temperature failure of conventional pipe and equipment both below and above surface occurred. Stainless steels gave more satisfectory performance under these conditions than did conventional steels. Oxygen was seldom observed in gas from wells ahead of the burning front, and it appears that the front was continuous throughout the life of the experiment. INTRODUCTION During late 1953 and early 1954, industry-wide attention was focused on the thermal recovery of oil by movement of a combustion front through an oil zone. Two separate Oklahoma field tests were described in publications by Kuhn and Koch, and Grant and Szasz. To obtain basic information needed for making engineering and economic appraisals of commercial recovery of heavy oil by this thermal recovery method, a new field research projecta3,4 was started May 31, 1955. Twelve oil companies contributed to this project with General Petroleum Corp. as operator. Since combustion recovery experiments* with heavy oils in other areas had been conducted in small patterns,"' an important purpose of this test was to determine whether the process could be operated in a pattern of near-commercial well spacing. The south Belridge field, located 30 miles north of Taft, Calif., was chosen because its oil sands are similar to many heavy oil sands which typically have low primary recovery and leave a large amount of oil in place. such fields are not particularly suited for common secondary recovery methods. DESCRIPTION OF TEST SITE The test interval was a Tulare sand at a depth of about 700 ft. Nine test wells were drilled, cored and completed from Oct., 1955, through Jan., 1956. The initial pattern shown on the map, Fig. 1, consisted of an injection well (II)', four producing wells (1P-4P), and four observation wells (IT-4T). An old well (81) was also recompleted for use as an observation well. The area enclosed by the original four production wells was 2.5 acres; the distance from the injection well to each production well was 233 ft. During the combustion period, Well 5P was drilled to replace Well 2P, and Well 6P was drilled to replace Well 3P. The new wells were 25 ft beyond the old production wells along a diagonal from the injection well, and resulted in an increase in pattern area to 2.75 acres. Isopachs are shown in Fig. 1. The average thickness of the oil sand in the test pattern was 30 ft. Fig. 2 presents two cross sections through the test pattern. Oil sand is represented by white and claystone by gray. The dashed lines indicate layers of conglomerate grading to claystone. The sand thickness was fairly uniform throughout the test pattern except in the 1P area. The sand body dips gently from the northwest to southeast, about 3 degrees from horizontal. The sand is unconsoli-dated, and grades from very fine material to pebbles as large as 2 in. in diameter. Table 1 presents the average initial properties of the formation. The in-place porosity of 37 per cent was estimated from the porosity of coke-consolidated cores taken after combustion. Original core analyses data were adjusted to 37 per cent, giving pore volume saturations of 60 per cent oil, 37 per cent water, and 3 per

By G. R. Marchant, B. K. Loveday

A mathematical model has been developed for flotation circuit simulation. This model was designed to investigate the effect of varying the circulating loads and to determine whether an improvement in overall efficiency could be gained by a size separation prior to flotation. Model parameters were obtained by regression to plant data. Highly correlated parameters in the model were combined to reduce the number of parameters so that the need for excessive data gathering was eliminated. Mass balance smoothing was used to obtain a consistent data set for regression. The results of the simulation indicate that for the same grade of concentrate, an increase in copper recovery of 0.6 per cent may be possible by increasing the circulating loads. The results of the simulation also indicated that recleaning of the plus 200-mesh material may be beneficial.

By Karen Dawson

This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.

By M. A. Trevits, I. R. Houlison, A. C. Smith, T. P. Mucho

Timely and rapid intervention to underground combustion events (fires, explosions, and spontaneous combustion) is the key to the successful control of the mine atmosphere and restoring of a coal mine to production. The focus of this paper is the utilization of a GAG 3A jet engine system to combat either large out-of-control fires or to render an entire mine inert when access to problem areas is difficult or impossible. This system is based upon a Soviet designed agricultural jet engine which consumes aviation fuel with oxygen (O2) from the intake air and exhausts combustion gases, primarily carbon dioxide (CO2) and water (H2O), along with the nitrogen (N2) from the air and small amounts of carbon monoxide (CO) and hydrogen (H2). The system is designed to approach stoichiometric combustion (ideally, pure burning that scavenges all the oxygen from the intake air). Therefore, these exhaust gases are almost entirely “inert gases”- i.e., gases which do not contribute to, and in fact, can suppress the combustion process due to the lack of oxygen. Other methods to inert mine areas have been used in the US and internationally, but these methods usually use low flow inertisation equipment or methods. Use of these low-flow inertisation equipment and methods has been successful in proactively rendering gob areas inert and has the ability to inert the entire mine workings. Due to the low flow rate, however, a substantial period of

By M. W. Kennedy

Prediction of the thermal duties of copper coolers in freeze lined furnaces is challenging. Where copper coolers are immersed in liquid slag the heat transfer is often defined by a natural convection cell immediately adjacent to the wall, in the absence of other factors producing forced convection. Slag coolers are typically not fully immersed, slag temperature, liquidus and superheat can vary, and bath levels may change significantly with batch tapping, leading to substantial variations in radiation heat fluxes. Radiation heat transfer is discussed with reference to the non-obvious impact of slag liquidus on radiation losses in the exposed cooler sections. Reference is made to literature and the results of analytical and FEM models.

By Augusto Viana Leandro Teixeira

Rare Earth Elements (REE) are fundamental for modern life products and green technologies. Supply constraints and the price peak of 2011 boosted intensive research for alternatives for processing and separation. Complex monazite- type, rare earth ores usually contain high acid consumption impurities, such as iron and aluminum, and radioactive thorium in their composition. These impurities are not removed by conventional concentration processes due to fine, micro-level association between the REE carrying minerals and the gangue minerals. This work presents a selective process route for REE extraction from iron-rich, monazite ores. The process involves sulfation by addition of concentrated sulfuric acid and pyrohydrolysis at temperatures of approximately 700–750 °C. Experimental results show REE extraction higher than 70% and low iron (below 5%) and thorium extraction (below 10%). A method based on thermogravimetric analyses was shown to be adequate to predict the behavior of a given ore sample in the sulfationselective pyrolysis-leaching process.

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

Polysaccharides have been used as depressants for naturally hydrophobic talc in the flotation of base metal sulfide ores, precious metal sulfide ores and platinum group metal (PGM) sulfide ores. The results of this surface chemistry study confirm guar gum as a preferred polysaccharide for talc depression in the flotation of these ores. In addition to the practical application of the research results, the surface chemistry results are of academic significance, providing further information to understand how polysaccharide depressants function in these complex sulfide flotation systems.