Search Documents

By Byoung Whie Lee

In order to investigate the change in surface energy as a function of cold work ad environment, the contact angles between a liquid and the surface of elec-tropolislzed aluminum with various degrees of cold work were measured. Specinlens cut from aluminum rod (99.99 pct Al) were annealed at 600°C for 24 hr and then cold compressed parallel to the drawing di-rectzon of the rod in increments of approximately 10 pcl from 0 to 70 pct. The sections, taken transversely to the drawing direction, were mechanically and electro chemically polished. Contact angles between the sessile drop of distilled water, glycerin, and glycol and the specimen surface were measured optically. The differences in interfacial energy were calculated from the contact angle data. The effects of chemical washing and surface roughness of the specimen on the contact angle were also studied. The liquid contact angle was a linear function of the degree of cold working (D) ad changed markedly with differed liquids. THE plastic deformation of polycrystalline metals induces a preferred orientation in crystal structure. A preferred orientation changes the atomic density of a metal surface. This change in surface atomic density brings about the changes in surface interactions of the metals."' Also, the plastic deformation of metals raises the internal energy by increasing the stored energy.' Consequently, the total Helmholtz free energy of the metal increases and, in turn, the surface free energy of the metal. In order to study the effect of plastic deformation on solid surface phenomena, the liquid contact angle of a sessile drop made on cold compressed and elec-trochemically polished aluminum was measured. The preferred orientation in aluminum, due to uniaxial compression, is known to be [110] direction parallel to the compression axis. However, this description is only a first approximation of a rather complex orientation. In actuality, half the crystallites are more than 10 deg from this orientation, regardless of the amount of compression." For randomly oriented fcc crystals, the average surface atomic density can be calculated as follows: The number of atoms in a unit volume is 4/a3, where a is a lattice constant. Hence, the number of atoms per unit surface area is about (4/a3)2/3 = 2.52/a2 However, when the preferred orientation took place along [110] direction, the surface atomic density is as follows: The area of (110) plane of a unit cell, considering ridges and valleys, is BYOUNG WHlE LEE, Member AIME, is Research Metallurgist, Atomic Energy Research Institute of the Republic of Korea, Seoul, Korea. Manuscript submitted May 29, 1968. IMD 2 x J2- a x Ga = 6a2 Since this plane contains 4 atoms, the surface atomic density is 4i6a2 = 2.3/a2 Upon changing from random to preferred orientations, the surface atomic density decreases about 10 pct. The increase in the stored energy and the change in surface atomic density due to plastic deformation would certainly alter the surface tension of a metal. EXPERIMENT High purity aluminum rod of 6-mm diam (99.99 pct Al, obtained from Johnson, Matthey & Co., Ltd, London, England) was cut into sections approximately 1 cm long. The transverse cross section was mechanically polished. Then, the specimens were annealed in air at 600°C for 24 hr. Thus, eight annealed specimens were uniaxially compressed at room temperature from 0 to 70 pct of cold working with an increment of 10 pct. The extent of cold working was determined by the percentage of reduction in axial length to the original length. The specimens were further polished mechanically and, then, electrochemically with the Modern Battelle Type 1 electropolishing solution with a current density of 0.3 to 0.4 amp per sq cm and an electrode potential of 8 to 12 v at the solution temperature of 78" to 82°C for approxirr~ately 5 min. The Modern Whlte Diffusing Screen \t/ --------------- re Goniometer for Mercury Lamp ^-^ Sessile Drop ¦=• Condenser c=> Microscope l_*~_i bJ Mlcromster Filer with Protmcter Fig. 1—Schematic diagram of apparatus set-up for liquid contact angle measurement.

Jan 1, 1970

By K. Tangri, M. Chaturvedi

The addition of 0.5 wt pct Cu to Zr-2.5 Cb alloy increases the as -quenched hardness of the hexagonal martensitic a' phase, produced by water-quenching bccß-Zr phase, by about 35 pct. This strengthening has been attributed to the solid -solution hardening of the matrix. On aging ternary martensite, a' phase reverts to equilibrium a and Zr2Cu and ß-Cb precipitate out, mainly at the twin and grain boundaries, causing a secondary hardening of the matrix. COLD-worked Zircaloy-2 pressure tubes have been in use in power reactors for a considerable period of time. The search for a better material led to the development of Zr-2.5 wt pct Cb alloy which in the quench-aged condition develops 50 pct more strength than that of cold-worked Zircaloy-2, however, its corrosion resistance in water and steam in the temperature range of 316" to 400°C, in absence of neutron flux, is inferior to that of zircaloy-2.' Work carried out by Ells et al.1 and Dalgaard2 has shown that the corrosion properties of Zr-2.5 wt pct Cb alloy can be considerably improved by the ternary addition of 0.5 wt pct Cu. This paper is concerned with the effect of 0.5 wt pct Cu on the formation of martensitic a and its aging characteristics in a Zr-2.5 wt pct Cb alloy. MATERIALS AND EXPERIMENTAL TECHNIQUES Zr-2.5 Cb-0.5 Cu (referred to as the ternary alloy) and Zr-2.5 Cb (referred to as the binary alloy) alloys, supplied by the Chalk River Nuclear Laboratories of the AECL were used. The detailed chemical analysis is given in Table I. Cold rolling and swagging with frequent intermediate anneal of 1000°C were used for the initial fabrication of the alloys. All the heat treatments were carried out after the specimens were wrapped in zirconium foils and encapsulated in silica tubes under a vacuum of 5 x 10-6 mm of Hg. For optical metallography and hardness measurements specimens were mechanically and then chemically polished in a 45 pct HNOj, 45 pct HzO, and 10 pct HF solution. Hardness was measured on a Vickers hardness tester using a 10-kg load. For each specimen at least fifteen indentations were made in order to obtain a representative value. The phase identification and structural analysis were carried out using X-rays and electron diffraction techniques. Wires of 1.5 mm diam reduced to 0.12 mm diam by chemical etching were used for making Debye-Scherrer powder patterns using Cu Ka radiation in a 114.6 mm diam camera. Carbon extraction replicas were prepared by etching the specimens, after depositing a layer of carbon on the metallographic specimen, in one part HF and thirty parts ethyl alcohol. Thin films were prepared by electropolishing heat-treated 3/4 by 1/2 by 0.005 in. thick strips using a modified Bollman-Window technique. The 10 pct perchloric acid-90 pct methyl alcohol bath was kept at -50°C and polishing was done at 5 to 10 V. The thinned specimens were washed in ethyl alcohol at -30º to -40°C and dried between filter papers. Replicas and thin films were examined in a Phillips 300 G electron microscope. For resistivity measurements thin strip specimens 0.02 by 0.3 by 10.0 cm long were used. The potential leads were spot welded to the specimens in order to maintain a fixed length for the initial and the final resistivity measurements. The resistivity was measured by a Kelvin bridge in a temperature controlled room. The temperature was maintained at 72º ±1°F and the accuracy of the resistivity measurements was 0.03 µa-cm. RESULTS As-Quenched Structures. In order to produce a homogeneous matrix to study the precipitation reaction the solution-treatments of both the alloys were carried out in the -field region. From the Zr-Cb phase diagram due to Lundin and cox3 ß/a + ß phase boundary for Zr-2.5 wt pct Cb alloy is 820°C. Ells et al.1 have reported this boundary for Zr-2.5 Cb alloy containing 1100 ppm 0 to be at 920°C. Also, the addition of 0.5 wt pct Cu reduces this temperature by 50°C. Therefore, the solution-treatments were carried out at 1000°C to ensure that the alloys were in ß-phase region. The soaking time was 1 hr and the specimens were water-quenched. The as-quenched hardness of the binary alloy was 245 Vpn whereas, that of the ternary alloy was 330 Vpn. The X-ray diffraction studies indicated that the as-quenched structure of both the alloys consists of martensitic hexagonal phase a', with a c/a ratio of 1.591, and some retained ß-Zr. The presence of a' phase was further confirmed by thin film electron microscopy. Electron micrographs of typical ß-quenched structures of the ternary and the binary alloys are shown in Figs. 1 and 2, respectively. Fig. 3 shows the diffraction pattern from an area similar to that shown in Fig. 1. Although, the as-quenched hardness of the ternary alloy is about 35 pct greater than that of the binary alloy, the structure of both the alloys seems to be the same. The matrix of both alloys is heavily twinned and shows very few dislocations. Furthermore, there is no evidence of any precipitation taking place in either of the two specimens during quenching from the solution-treatment temperature. Aging Behavior of Martensitic a'. The aging kinetics of the ternary alloy were followed by resistivity and hardness measurements. The as-quenched values

Jan 1, 1970

By R. M. Asimow, J. J. Svitak

Tile crilical resoll,r,d shear stress, CRSS, for slip of slow1y cooled Ag-All single crystals was measured at 201K. Tlze importance of short-range order and Suzuki sogregalion was inrestigated by deter~rlining llze ciic.cl of quenching on the CRSS. Thr obserz.ed rfrtenching effects were generally small and indicate that short-range ordcr and Slczuki srgregation do no1 account for n significant portion of the solid-solution strengthening in this system. However, all alloys slzozcwi yield drops ulhich rilere heat- lreat nrenl-sensiline THERE have been a number of mechanisms proposed to explain alloy strengthening in the Ag-Au system. The effectiveness of some of the proposed mechanisms, especially those that depend on Suzuki segregation1" or on short-range order,2-6 SRO? should be strongly dependent on heat treatment. Since internal friction investigations in this system indicate that there is stress-induced order,' we must also consider the possibility of local atomic rearrangement or short-range ordering in the stress field of a dislocation. There is not complete agreement whether these mechanisms should be most effective in raising the flow stress, in causing yield drops. or some combination of these two effects. This work was undertaken to determine the effects in the Ag-Au system of mechanisms that depend on segregation or order by using known but drastically different cooling rates following a high-temperature treatment. By comparing the critical resolved shear stress, CRSS, for slip measured after a very slow cool and again after a fast cool (quench) of the same crystal, it is possible to determine the effect of cooling rate on CRSS* and on yield drops. The single-crystal CRSS was determined at several compositions because there has been no data published across the phase field since the publication of room-temperature flow stress by Sachs and Weerts.' EXPERIMENTAL PROCEDURE Starting with materials of 99.999 pct purity, single-crystal specimens of random orientation 1.25 mm square by 4 cm long were prepared with 0, 10, 14, 25, 30. 50, 70. 75. 80, 90. and 100 at. pct Au. Crystals were grown in an inert atmosphere using a modified Bridgman technique with a growth rate of 1.5 cm per hr in a gradient of 3°C per cm. To obtain a maximum practical degree of SRO, the crystals were cooled at a rate of 275'C per hr to about 310°C and then cooled at 6°C per hr to approximately 200°C. Specimens were tested in tension immersed in an alcohol bath at -72°C (201°K) at a strain rate > = 0.003 mm"1 to determine the CRSS (7). The activation volume of several crystals was determined from the flow stress increment (72 - T1) for a tenfold increase in strain rate. The total shear strain varied from 0.05 to 2.3 pct but was generally less than 0.4 pct. After testing, each crystal was then held at 500°C for 10 min, quenched into brine at -35°C and. after storage at -71°C for 1 day, retested in tension using a procedure identical to that of the first test. The quenching apparatus, see Fig. 1, was designed to enable accurate temperature control and rapid quenching while preventing specimen contamination and accidental deformation. Test data from a specimen with a fine thermocouple spot-welded to it indicated a cooling rate of 104C per sec. The relatively low heat-treatment temperature was chosen to minimize quenching defects caused by a large vacancy

Jan 1, 1970

By H. A. Halupka, I. A. Mozer

"At its plant in San Juan, Peru, Marcona Mining Company operates two grate pelletizing furnaces for the agglomeration of 3.5 million long tons of magnetic concentrates annually. Line One, installed in 1963, was built by Lurgi as a downdraft process furnace utilizing a furnace fan for the recuperation of hot gases from the cooling zone. This line was modified in 1966 to include both updraft drying and downdraft drying, and the original roof burners were converted to side-wall burners. Line Two, a Dravo-Lurgi furnace with an annual capacity of 2.4 million long tons, was built in 1966. This line, in contrast to the modified Lurgi furnace, employs direct recuperation of hot gases from the cooling zone and utilization of process gases from the firing zone for updraft drying.At its plant in San Juan, Peru, Marcona Mining Compa-ny operates two grate pelletizing furnaces for the agglo-meration of 3.5 million long tons of magnetic concentrates annually. Line One, installed in 1963, was built by Lurgi as a downdraft process furnace utilizing a furnace fan for the recuperation of hot gases from the cooling zone. This line was modified in 1966 to include both updraft drying and downdraft drying, and the original roof burners were converted to side-wall burners. Line Two, a Dravo-Lurgi furnace with an annual capacity of 2.4 million long tons, was built in 1966. This line, in contrast to the modified Lurgi furnace, employs direct recuperation of hot gases from the cooling zone and utilization of process gases from the firing zone for updraft drying. 5 per cent increased capacity, 30 per cent lower fuel oil consumption, and approximately 400 per cent reduction in grate bar and pallet corrosion. Firing of the pellet bed was improved by conversion from roof to side-wall burners. This modification also permitted utilization of monolithic refractory in place of pre-fired shapes, thereby improving over-all furnace availability and reducing refractory stock requirements from 154 different shapes to 18.Data are presented to compare operating performance of the Dravo-Lurgi furnace and the modified Lurgi furnace. These data show 30 per cent lower fuel oil consumption and 10 per cent higher capacity per unit grate area for the Dravo-Lurgi furnace, which also averages higher availability due to greater operating flexibility."

Jan 1, 1970

By John V. Beall

Thai means free. Historically accurate, as the country has never been subjugated by foreign occupation, the name "The Land of the Free" also seems to fit the attitude of the people. At the Bangkok airport, without so much as a kopkhun (thank you), travelers are found behind, beside and in front of ticket counters. A pretty Thai face on TV calls flights in English and Thai. Baggage disappears with alarming rapidity and your reporter and spouse despaired of ever being reunited with it. But at the entrance, all the parts came together and there was even a limousine from our hotel, The Oriental. Driving downtown English style, we noted that there were four lanes of traffic occupying the space we would allow for three lanes. Motorcycles and enclosed three-wheel motorcycle taxis were much in evidence, but the occasional water buffalo held up the slow lane. In the city, men wore European-type slacks and shirts but the women were colorful in traditional ankle-length wraparound skirts.

Jan 1, 1970

By Nathaniel Arbiter

After almost 60 years of application in this country froth flotation is still by far the most important process for concentrating metallic ores as well as a number of nonmetallic ores including fluorspar, phosphate rock, and potash. Its use on iron ores and coal is increasing. In the metals groups the largest plants and the greatest progress are found in copper and molybdenum mills, and the section of this paper that deals with applications will be found most pertinent to that field. During its long reign the flotation process has passed through several phases of evolution and has achieved progress in economy, efficiency, and simplicity of operation. Much of today's success in the flotation of low-grade ores can be attributed to that progress. Even more important to us than our ability to cope with today's conditions are tomorrow's problems, which we can contemplate with some prescience and confidence. Our annual production of copper, lead, zinc, and molybdenum--to mention only the most important metals occurring in the U.S. as sulphides--must be held at a high level in the face of a declining grade of ore. It is probable that the tonnage of such ores mined and processed will double in this country before the turn of the century. Not only will many of the existing flotation mills be enlarged again and again, but larger mills will be built here and abroad to meet our needs. At this moment, in fact, there are at least three proposed new foreign mills or expansions that envision 100,000 tons daily milling rate on copper ores. Table I (1) shows the trend in copper ore grades in U.S. in recent years:

Jan 1, 1970

By S. S. Lisnyak, B. D. Lichter

An important question in the study of the "hot corrosion" phenomenon (i.e., accelerated oxidation of Ni-Cr-base and Co-Cr-base "superalloys" in the presence of sulfur) is the condition of formation and physico-chemical properties of different sulfides in the system Ni-Co-Cr-S. seyboltl has observed the presence of ((chromium-rich" sulfides of compositions M3S4, and M2S3 in the scales of superalloys after hot corrosion; however, as he points out, much confusion exists as to the identity of sulfides found on Ni-Cr and Co-Cr alloys. According to the literature,&apos; ternary sulfides, e.g., NiCr2S4, (monoclinic structure) and CoCr2S4 (spinel structure) exist in these systems. Therefore, it is likely that these compounds are found in the scale of alloys undergoing hot corrosion. At present this possibility has not been discussed in the literature. Accordingly, we have begun investigation on the properties of ternary sulfides and their mutual interaction. The magnetic and electrical properties of pure NiCr2S4 and pure CoCr2S2 have been previously determined."-&apos; In the present work we have studied the interaction between these sulfides at high temperatures by means of X-ray diffraction and magnetic susceptibility. The measurements were carried out at room temperature after appropriate thermai treatment of samples at high temperatures. For alloys containing the three elements nickel, chromium, and cobalt this interaction may be of importance in the study of the hot corrosion phenomenon. The compounds NiCr2S4 and CoCr2S4 were prepared from stoichiometric amounts of the elements and CoS in the case of CoCr2S4. Samples were mixed and sealed in evacuated silica tubes, slowly heated to 900&apos; to 100O°C, and held at temperature for a total of 120 hr (NiCr2S4) or 80 hr (CoCr2S4) with intermediate re-grinding~. X-ray diffraction showed a pure spinel structure for CoCr2S4 and a monoclinic structure for NiCr2S4. Samples of mixtures of the two ternary sulfides were prepared with different compositions, see Table I. Samples were heated for a total of 80 hr at 900&apos;C in evacuated silica tubes, with one intermediate regrind-ing. The capsules were slow-cooled to room temperature in the furnace. Samples for X-ray diffraction were prepared by placing powder on a glass slide with vaseline. Dif- fractometer traces were obtained on a G.E. XRD-5 diffractometer using a chromium tube and vanadium filter (40 kv and 31 ma). The size of the spinel unit cell was determined from the eight highest angle peaks (80 deg < 2b < 160 deg). Calculated lattice parameters were plotted vs cos B . ctn 0 and extrapolated to 6 = 90 deg. Measurements of the magnetic susceptibility were carried out at room temperature using the Faraday method in a magnetic field of 3000 G and using a Cahn RG automatic microbalance. The system was calibrated from the well-established susceptibilities of platinum and palladium: (Xpt = 0.968 x 10-6 g-1 and Xpd 7 5.04 x 10~6 g-1). The weight of samples were approximately 0.200 g. X-ray diffraction patterns for unsintered mixtures showed Bragg peaks from both the spinel (CoCr2S4) and monoclinic (NiCr2S4) structures. After sintering no monoclinic peaks were observed in samples containing up to 40 mol pct NiCr2S4. However, the spinel peaks were displaced to higher angles with increasing

Jan 1, 1970

By Roland W. Rammler

With oil consumption increasing more rapidly than known reserves in industrial countries, there has been a growing interest in the production of synthetic crude oil. The main starting materials for such production are coal, oil shale and tar sand, all of which occur in enormous quantities in North America. A process sequence suitable for all three of these starting materials incorporates a preliminary retorting step to produce oils for subsequent hydrotreating. For this retorting step, a technique known as the Lurgi-Ruhrgas process has proven highly efficient. The process has been commercially used for the flash carbonization of coal and has also been tested in pilot- plant experiments with oil shale and tar sand.

Jan 1, 1970

By C. J. Sullivan

"The outlook for supplying the world's metal needs in the next twenty-five years is good, although in several cases basic costs are likely to increase with rising demand. Metal prices calculated at a constant dollar from 1900 to the present show that for nickel, copper, silver, lead, zinc and tin, prices -and presumably production costs -fell from 1900 to the early 1930s. Since then, they have generally risen, apparently reflecting some depletion in relation to demand. This tendency has been accentuated since the post-World War II adoption of managed, full-employment, growth economics, which have resulted in a sharp escalation in world demand for metals. (Abandonment of such policies, apparently now under consideration in North America, would, of course, affect the pre-dictions of this paper.) Nevertheless, metal prices generally are still below those prevailing in 1900. Exploration potential exists for disseminated ores of many metals still thought of as characteristic of lode and vein deposits. These include uranium, silver, gold, tin and nickel and, to a lesser extent, lead and zinc. Considering the discovery potential for some principal metals in relation to expected demand and prices, I would tend to rate them as follows: molybdenum, zinc, lead, uranium, silver, gold, tin, nickel and copper."

Jan 1, 1970

By Carl E. Norman

An investigation of geologic structure on macroscopic, mesoscopic, and microscopic scales was conducted on near-surface igneous and metamorphic rocks in which the existing stress field was determined by in situ methods. A consistent NE-SW orientation of the maximum compressive stress in the horizontal plane at four of five test localities appears due to the intrusion of NW-trending diabase dikes. Structural features at the mesoscopic scale show no consistent directional relationship to determined stress directions. Petrofabric diagrams of open microfractures show preferred orientations, but these are not consistently related to the orientations of larger structural features, such as joints, foliation, or mineralized shear zones. However, at five of six test sites the preferred direction of microfractures occurs nearly perpendicular to the maximum principal stress directions; an anomalous parallel relationship exists at a test site in an intrusive rock body. The results suggest that the open microfracture subfabric may provide a means for gaining information on the directional properties of stress fields. Such information can be obtained from oriented cores taken from holes which exceed the approximate 100-foot depth to which other in situ methods are presently limited.

Jan 1, 1970

By A. E. Dwight, Paul A. Beck

Known CsCl-type phases in transition metal alloys are shown to be formed preferentially at an electron concentration of approximately 6; a tetragonally distorted version of the CsCl structure is stable at -e/a = 6.5. The relationship of the distortion to electron concentration is verified by experimental data for the quasibinary systems Time ,Os) , Ti(Re,Ir), and Ti(Re,Pt) and the ternary system Ti-Ru-Rh. It was noted some years ago1j2 that the occurrence of CsC1-type ordered structures in equiatomic binary alloys, AB, of transition metals correlates with the location of the component elements in the periodic table. One of the components, A, must be to the left and the other component. B, must be to the right of the chromium group. It was pointed out2 that the CsCl structure does not occur in CrFe. is metastable in VFe,3 and is stable in TiFe up to high temperatures, and that this progressively increasing stability may correspond to an increase in electron transfer between the two components and to a correlated decrease of the magnetic moment associated with the iron atoms. Such a decrease was in fact later demonstrated by Nevitt. 4 The binary CsC1-type phases that are formed by a transition metal with either another transition metal or a lanthanide are listed in Table I. Thirty-three of these phases occur at an average electron concentration (average number of electrons outside of closed shells) of e/a = 6. The five phases that are formed at an electron concentration of e/a = 5.5 appear to be borderline cases. This is suggested for instance by the fact that TiRe is bcc. without any long-range order, while TiTc (at the same electron concentration) has a CsCl ordered structure. Six of the undistorted CsCl phases formed by transition metals with one another have an average electron concentration of e/a = 6. 5. Table I. With the exception of Zr4,Rhs4 and Hf48Rh52. the B component in these phases is a first long-period transition metal, i.e.. iron or cobalt. TiNi. with an electron concentration of e/n = 7, appears to undergo transformation at around room temperature to a more complex ordered struct~re.~ The five other CsCl structures known to occur at e/a = 6.5 have either scandium or a lanthanide metal as the A component; the difference in the elec-tronegativity and in the e/a ratio between the component elements is in these phases very large, A(e/a) - 7, and they may be expected to have a rather strong ionic bond component. Presumably the ionic bond stabilizes the CsCl-type structure at the equiatomic composition and it overrides the electron concentration requirement. When the B element is not from the first long period and the A component is not a rare earth metal. equiatomic (AB) alloys of transition metals with an average electron concentration of e/a = 6.5 in most cases have a crystal structure closely related to the CsC1-type, but slightly distorted tetragonally, Table I. This was first found6 for VRu, NbRu. and TaRu. It was noted6 that the undistorted CsCl structure is also stable in the three systems. but at a lower electron concentration, near e/a = 6. In these systems this requires a deviation from equiatomic stoichiometry. which is otherwise ideally suited for the CsC1-type structure. A similar situation was later found in the Ti-Rh7 and the Ti-Ir systems. 8 The Ti-Rh alloys undergo a second distortion and become orthorhombic when the rhodium content becomes somewhat larger than 50 pct. As mentioned previously. TiRe does not have the CsC1-type ordered structure. In order to investigate how close TiRe is to the borderline of stability of the

Jan 1, 1970

By Norman Weiss

There was a time in the early history of man&apos;s use of metals when ore could be directly reduced to usable form by the use of fire. In those days the term "milling," or its many synonyms signifying the concentration of an ore&apos;s metallic con- tents before smelting, was little known. Centuries later, even before Agricola, or even before the Greek and Roman civilizations, simple means were found to concentrate metallic minerals that possessed special characteristics such as high specific gravity, hardness, magnetic response, or simple appearance. In this way, the art of milling became valuable to civilization because it eliminated most of the cost and labor of transporting and melting the worthless nonmetallic part of an ore. As civilization became more dependent upon metals and solid fuels, the art of ore dressing (one of our synonyms) increased in importance and complexity, until today it has become a gigantic industry firmly based upon a mature but rapidly advancing technology. Technically trained people are needed in growing numbers to serve this industry.

Jan 1, 1970

By C. R. Whitney, G. N. Maniar, D. R. Muzyka

Previous results have shown that Pyromet 860, an Fe-Ni-base heat-resistant alloy, is stable at temperatures as high as 1500°F for aging times as long as 100 hr. This Paper describes the results of long-time creep-rupture testing at 1050" to 1400°F at various stress levels. Times as long as 37,660 hr were employed. The effects of time, temperature, and stress on the precipitates and their morphologies were studied by optical and electron microscopy, X-ray and electron diffraction, and microprobe techniques. phase, containing cobalt, nickel, and molybdenum, was detected after extended exposures from 1200" to 1400°F and careful study was performed to describe the kinetics of its formation in this alloy. µ phase formation apparently has little effect on the elevated-tem-perature properties of Pyromet 860. For times as long as 500 hr at 1300°F and below, with µ phase present, m significant effects on ambient temperature properties were noted. For longer times at 1300°F and after 1400°F exposure, the effects of u phase on ambient temperature tensile strength properties are not clear due to y&apos; effects and grain boundary reactions. Electron-vacancy, N,, numbers were calculated using different methods described in literature and correlated with the present findings. In the selection of alloys for use in gas turbine applications, structural stability ranks as a primary criterion. High-temperature strength and cost are also of major concern. With these factors in mind, Pyromet 860 alloy, an Fe-Ni-base superalloy was designed. This alloy combines the cost advantages of Fe-Ni-base alloys such as A-286, 901, and V-57 with improved strength and structural stability&apos;1,2 and no tendency to form the embrittling cellular 77 phase. A previous study3 reported on the stability of Pyro-met 860 at temperatures from 1375" to 157 5°F and times up to 100 hr. That study showed that the y&apos; precipitates increased in size and separation and decreased in number with an increase in time or aging temperature. No deleterious phases were found to occur. In the present work, samples from four production heats were subjected to long-time creep-rupture testing at 1050" to 1400°F at various stress levels. Various heat treatments were used on the starting samples and tests were run up to 37,660 hr. The effects of time, temperature, and stress on the precipitates and their morphologies were studied by optical and electron microscopy, X-ray and electron diffrac- tion, and microprobe techniques. Electron vacancy numbers, Nv , calculations were made by TRW.4 Experimental results are correlated with the Nv data used to predict occurrence of intermetallic phases such as a phase. EXPERIMENTAL PROCEDURE Mechanical Tests. Material for the present study came from four production size heats of Pyromet 860 alloy, weighing from about 3000 to about 10,000 lb. All of these heats were made by vacuum induction melting plus consumable electrode vacuum remelting. The nominal analysis for this alloy is compared with the actual analysis of the four heats in Table I. Sections of these heats were forged to 9/16-in. round bar,3/4-in. square bar, 3-in. round bar, 4-in. square bar, and a gas turbine blade forging about 16 in, long, about 6 in. wide, and weighing about 20 lb. In general, all forging of this alloy is done from a 2050°F furnace temperature. Longitudinal test blanks were cut from the centers of the smaller bars, from mid-radius positions for the 3- and 4-in. bars, and from the air foil of the gas turbine blade and heat-treated according to the procedures outlined in Table 11. Heat treatment A is the "standard treatment" recommended for this alloy for best all-around strength and ductility. Heat treatment B is a modification of treatment A for improved tensile strength at moderate temperatures. The treatment coded C was designed for treating large sections according to a procedure previously described.&apos; Heat treatment D was developed to yield optimum stress relaxation characteristics at 1050°F for a steam turbine bolting application. After heat treatment, the test blanks were machined either to plain bar creep specimens with a gage diameter of 0.252 in., to combination smooth-notched stress-rupture bars with a plain bar diameter of 0.178 in. and a concentration factor of Kt 3.8&apos; at the notched section, or to notch-only specimens. All specimens conformed to ASTM requirements. Metallography. Most of the creep-rupture tests were continued to failure. A few bars were fractured as smooth or notch tensiles after creep-rupture exposures. After fracturing, ordinary metallographic sections were made primarily in gage areas adjacent to fractures to represent a "high-stress" region and through specimen threads to represent a "low-stress" region. All metallographic sections were made in a longitudinal direction with respect to the test specimen axes. For optical microscopy, the samples were etched in glyceregia (15 ml HC1, 5 ml HNO,, 10 ml glycerol). For XRD analysis, the phases were extracted electrolytically in two media: 20 pct &Po4 in H20 for selective extraction of y&apos; and 10 pct HC1 in methanol for carbides and other phases.

Jan 1, 1970

By Thornton L. Neathery

The low-grade talc deposits in Tallapoosa County, Alabama, are associated with a mafic-ultramafic rock complex that is part of a widely distributed schist and gneiss group. These rocks form a synform structure overlying Inner Piedmont lithology. Paragenetic sequence of the Tallapoosa talc is interpreted as enstatite-anthophyllitetalc. Talc occurs as massive boulders formed by the alteration of enstatite-anthophyllite and as finely disseminated discrete particles in the enclosing saprolite matrix. Weathered rock reaches depths as great as 60 feet. The quality and quantity of the talc, however, are variable. Mineral analyses of the talc-bearing samples, by petrographic grain count, indicate a talc content of 16 to 26 percent. Most of the talc occurs as plates or scales that are moderately stained with limonite. Fibrous talc also occurs in the deposits and is often mistaken for anthophyllite asbestos which is intimately associated with the talc. The size, shape, and occurrence of the talc deposits precludes any method of min¬ing other than open-cut. A small-scale mining operation began in the district in 1969. Potential capacity of the operation is 5, 000 tons per year. Inferred reserves, based on field investigations, are placed at approximately 8 million tons. Approved for publication by the State Geologist, Geological Survey of Alabama.

Jan 1, 1970

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment these off-process waters require excessively large areas for containment. To discharge the waste water into natural waterways would contribute to stream pollution and likely would not be permitted. In Bureau of Mines experiments conducted in the Twin Cities Metallurgy Research Center&apos;s 900-lb/hr pilot plant, approximately 85 percent of water requirements for the flotation-based treatment of a Michigan nonmagnetic taconite were met by reclaimed water. Water reclamation of the off-process streams from flotation was accomplished by controlled additions of lime, sodium carbonate, and a synthetic flocculant to reduce turbidities to <1,000 ppm equivalent Si02, while maintaining a Ca(II) content of 516 ppm in the finished effluent. Flotation concentrates of good quality were obtained using the reclaimed water. The cost of chemicals used in water reclamation was approximately equal to the savings in flotation reagents attributed to recycling of the water.

Jan 1, 1970

By J. R. Cahoon, H. W. Paxton

The mechanical properties of unidirectionally solidified A1(rich)-Mg and A1(rich)-Cu castings containing up to 15 wt pct solute have been determined with re -spect to the volume fraction of interdendritic eutectic. Pioperties were determined in the directions pumllel and Perpendicular to that of solidification; the volume fraction of eutectic was varied between the "as-cast" and equilibrizcm amounts by approperiate heat treatment following solidification. The principles of fiber strengthened composites and dispersion strengthened materials are adapted to explain the mechanical properties of these castings. It is generally accepted that castings often have inferior mechanical properties when con~pared to wrought products. However, there is little quantitative data available concerning the factors which make apparently sound castings weak and/or brittle. The relative ease and inexpensiveness of the casting process have always been attractive and, therefore, an understanding of the factors which contribute to the mechanical properties of castings would seem desirable. Such an understanding may lead to an improvement in the mechanical properties to an extent where castings would become competitive in applications where presently only wrought products are considered to have the requisite properties. Such an understanding could also improve the reliability of present cast products. Much of the recent research on castings has centered about determining the extent of segregation in cast alloys. Macrosegregation, particularly inverse segregation, has been studied in some detail 1-8 and a considerable understanding of microsegregation has been obtained.9&apos;10 The effect of solidification rate on dendrite spacing and on the amount of interdendritic eutectic in binary alloys has been established, particularly for Al(rich)-Cu alloys.""0 However, the extension of these ideas to relate the amount of interdendritic eutectic, concentration gradients, micro-segregation, dendrite spacings, and so forth, to the rnechanical properties has been limited. Dean and spear" have related the mechanical properties of an Al-Si-Mg alloy, A356-T62, to the dendrite spacing and have shown that the mechanical properties improve with decreasing dendrite spacing. Passmore et al.12 have shown that annealing at high temperature improves the mechanical properties of Al(rich)-Cu al- loys and Archer and Kempf 13 have shown that an Al-1 pct Mg-1.75 pct Si alloy behaves in a similar manner. Ahearn and Quigley 14 have shown that high temperature homogenization also enhances the mechanical properties of an SAE 4330 steel. However, in the above investigations, no underlying reasons were suggested for the improvement in mechanical properties. The purpose of the present investigation is to relate the mechanical properties of castings to some of the solichfication variables and to derive some equations by which calculations of the mechanical properties may be attempted. In particular, the effect of the amount of interdendritic eutectic and the effect of stress direction with respect to that of solidification on the mechanical properties will be considered. The Al(rich)-Mg and Al(rich)-Cu binary alloy systems were chosen for study. The A1-Mg system was chosen because its constitutional relationships are such that large volunles of eutectic (up to 24 vol pct) may be obtained in the as-cast condition and then be completely dissolved by subsequent heat treatment at about 440°C. This allows a comprehensive study relating the mechanical properties of castings to the amount of interdendritic eutectic. Also the Al(rich)-Mg eutectic is almost a single phase 15 which should make the experimental results more amenable to theoretical interpretation and calculation. The A1-Cu system was chosen for study because of the large amount of related information available concerning segregation, dendrite spacing, and so forth. Unidirectionally solidified castings were used throughout the investigation so that the effect of solidification direction with respect to the direction of applied stress could be determined. THEORETICAL It is well known that upon solidification of binary alloy castings, the nonequilibrium amount of eutectic which forms is given by 10 where fe o is the weight fraction of eutectic, Cs is the solid solubility of solute at the eutectic temperature, k is the equilibrium partition coefficient, and C, is the average composition of the alloy. In the development of Eq. [I], it is assumed that the effects of inverse segregation and diffusion in the solid are negligible, and that no porosity is present. If the casting is homogenized at a high temperature for a long period of time, some (or all) of the eutectic is dissolved and the amount of eutectic for this "equilibrium" condition may be calculated directly from the constitutional diagram. By appropriate intermediate annealing, the

Jan 1, 1970

By Willard L. Hunter

Four solvent extraction systems were studied to determine their efficiency jor extraction and separation of tantalum and columbium. Aqueous feed solutions of varying HF-HCl concentrations and metal content were contacted with equal volumes of cyclohexanone, 3-methyl-2-butanone, and 2-pentanone and solutions of varying HF-H2S04 concentrations were contacted with equal volumes of 2-pentanone. One multistage continuous test was made in a polyethylene pulse column using cy clohexanone as the organic phase. In each system studied, columbium and tantalum purities in excess of 95 pct with respect to each other were obtained in single-stage tests at low acidities in the feed solution. Separation factors ranging from 1700 to 2400 were obtained when rising HF-HCl mixtures in the aqueous phase. Best results were obtained when a solution of HF-H2S04 was used as the aqueous phase and 2-pentanone as the organic phase. A separation factor in excess of 6000 was obtained in one stage with aqueous solution concentrations of 2 _N HF and 2N H2S0,. When acid concentrations were increaszd to 52 HF and 10 _N H2S0,, 99.9 pct of the tantalum and 98.2 pct of the columbium initially present in the feed solution were transferred to the organic phase. The separation of columnbium and tantalum obtainable by means of the solvent extraction systems presented in this paper was found to corn -pare favorably with other systems, including the HF-H2SO4-methyl isobutyl ketone system currently used by most producers for the extraction and separation of these metals. TANTALUM and columbium are always found together in minerals of commercial significance, although the proportion of the two metals in ores varies within broad limits. Columbium is estimated to be 13 times more abundant than tantalum. Five methods generally employed for the separat:ion of these metals are: 1) fractional crystallization (the Marignac process),2 2) solvent separation, 3) fractional distillation of their chlorides, 4) ion exchange, and 5) selective reduction. Of these methods, the one currently used by industry to the greatest extent is that of solvent separation. One of the early technical developments in solvent separation of tantalum from columbium was reported by the Bureau of Mines: the HF-HC1-methyl isobutyl ketone system; data were presented for both laboratory and pilot-plant experimentation.3 Of twenty-eight organic solvents tested for their ability to extract tantalum from an HF-HC1 solution of columbium and tantalum, 3-pentanone (diethyl ke-tone), cyclohexanone, 2-pentanone, and 3-methyl-2-butanone were chosen for further study. Data on the HF-HC1-diethyl ketone system has been published4 and data describing the use of cy clohexanone, 2-pentanone, and 3-methyl-2-butanone as the organic phase are included in this report. RAW MATERIAL The source of tantalum and columbium oxides for this study was (&apos;Geomines" tin slag from the Manono Smelter, Cie Geomines, Gelges, S.A., Congo. In order to extract the valuable Ta-Cb content, the slags were carbided, chlorinated, and the sublimate from chlo-rination was hydrolized and washed free of chloride with water. The washed material was air-dried and stored in a stoppered container. Throughout the paper, "feed material" refers to this mixture of hydrated oxides which was employed because of its high solubility in aqueous solutions. Typical analysis of the hydrated oxides is shown in Table I. I) HF-HC1-CYCLOHEXANONE SYSTEM Batch Separation. Effect of Acid Concentration. To determine the effect of varying the acid concentration upon the transfer of tantalum and columbium, a series of tests was made in which approximately 2.5 g of feed material was added to 25 ml solutions of 2, 4, 6, 8, and 10 N HF and 0 through 5 N HC1. Tantalum pentoxide concentration of the solu%ons was approximately 21 g per liter and columbium pentoxide was 14 g per liter. These starting solutions were shaken with equal volumes of cyclohexanone in 100 ml polyethylene bottles for 30 min. The phases were carefully separated in 125 ml glass separatory funnels. The time of contact of the solutions with the separatory funnels was kept at a minimum to reduce silica contamination. The measured phases were separated into 400 ml polyethylene beakers and the metal contents of each were precipitated by addition of an excess of ammonium hydroxide. Precipitate from each phase was filtered on ashless filter paper, ignited at 800" to 1000°C for 45 min, weighed, and analyzed by X-ray fluorescence.5 Data tabulated in Table I1 and illustrated in Fig. 1, show that maximum separation of tantalum from columbium for each HF concentration was obtained with no HCl present. The purest tantalum product was obtained with some HCl present. The highest separation factor was obtained at 2 N HF and

Jan 1, 1970

By M. M. Wong, D. E. Couch, G. M. Martinez

The Bureau of Mines electrowon hafnium metal with an average oxygen content of&apos; 150 ppm at 700°C from an electrolyte containing 27 wt pct LiCl, 62 wt pct RbCl, and 11 wt pct HfC14. The average anode and cathode current efficiencies were 90 pct at anode and initial cathode current densities of 86 amp per sq ft. Haf-nium metal with an average oxygen content of 440 ppm was electrowon at 800oC from an electrolyte containing 90 wt pct KC1 and 10 wt pct HfCl4. The average anode and cathode current efficiencies were similar to those obtained in the LiCL-RbCl-HfCl, electrolyte. The chlorine gas given off at the graphite anode was vented through either a silica or a graphite tube to prevent cell corrosion. THE current method for the commercial production of high-purity hafnium is the thermal decomposition of Hfl4.1 The iodide method is not adaptable to continuous process techniques. Nettle, Hiegel, and Baker2 studied the electrorefining of hafnium from hafnium sponge containing 800 ppm oxygen. They failed to obtain hafnium with 600 ppm oxygen in their initial deposits and obtained AEC specification for oxygen only after 75 pct of the soluble hafnium had been removed from the electrolyte. Calculations using their data indicated this was approximately 4 lb of hafnium. The electrolyte was then used to produce approximately 3 lb of hafnium with a low oxygen content. However, no data are shown concerning the amount of anode material initially used or what percent of it was dissolved, therefore, results are not suitable for evaluation of a continuous operation. In general, it was not possible to consistently obtain low oxygen content metal with the electrolytes described by Nettle, Hiegel, and Baker. Wong, Hiegel, and Martinez3 investigated the electrorefining process for hafnium and showed that even by strict control of electrolyte composition only relatively low oxygen reduction could be obtained. The oxygen contained in the hafnium anode material tended to transfer to the cathode deposit and only a limited purification was possible. Both the "iodide" and the "electrorefining" processes depend upon hafnium sponge as a starting material. The sponge is normally produced by magnesium reduction of HfC14 &apos; and does not meet AEC specifications for hafnium metal. Since only 30 pct of the anode feed could be utilized3 in the electrorefining cells, the Bureau of Mines developed an electrowinning process. HfC14 was used as the feed material for the electro-winning process described in this report. Many of the electrolytes used in the electrorefining studies3 ap- peared to be suitable carrier-electrolytes for HfC14. However, in the initial studies on electrowinning, it was desirable to use electrolytes that had low solidus temperatures and could be operated over a wide temperature range to investigate parameters of the process. Therefore, electrolytes containing LiC1, NaC1, KC1, RbC1, CsC1, and HfC14, in various combinations were explored. EQUIPMENT Chlorinator. Hafnium carbide was chlorinated to produce HfC14 in the batch-type chlorination shown in Fig. 1. Chlorination temperatures were measured with a thermocouple placed in the center of the HfC charge. A flow meter was used to monitor the helium and chlorine. The exhaust side of the silica chlorina-tor tube was equipped with a flask for collecting organic material released during the initial heating of the HfC. The temperature of an internal heater, which extended from the HfC14 condensing flask to the hot end of the chlorinator, was adjusted to prevent the HfC14 from condensing before entering the collection flask. Helium and excess chlorine were exhausted through the lid of the collection flask to an aqueous NaOH solution. Sublimer. Initial studies were conducted using a sublimer, Fig. 2, made by placing a 13/8-in. OD nickel thimble 11 in. long, inside a 11/2-in. ID nickel bell 12 in. long, and locking it in place. This unit was loaded with HfC14 and partially immersed in the molten electrolyte for sublimation directly into the electrolyte. In another sublimer shown in Fig. 3, the HfC14 was contained in a "resin reaction flask". Quartz wool, previously heated to 600aC, secured between two nickel wire screens, was placed just above the HfC14 powder. The lid contained a vacuum outlet, a gage, an argon inlet, and an air-cooled pipe for condensing the HfC14. This sublimer was evacuated and heated. The sublimation temperature was not critical and the sublimer operated satisfactorily at all temperatures between 250" and 350°C. Electrolytic Cell. The electrolyte chamber, Fig. 4, was made of mild steel 8-in. schedule 20 pipe, 30 in. long. The exterior was metallized with a Ni-Cr alloy. The electrolytes were contained in a 16 gage nickel or iron liner with a nickel heat shield on top. The cell was heated by a resistance furnace. A 21/2-in. ID by 25 in. long air lock was connected to one port of a two-port cell cover assembly through a slide valve. The cover assembly of the air lock was electrically insulated from the cell and was equipped with a rubber sleeve that provided for the passage of the cathode lead. This allowed the cathode deposits to be removed and a new nickel cathode to be introduced without allowing air to enter the cell. A tube-rod assembly was bolted to the other port on the cell cover assembly and was sealed by a packing seal. The tube-rod assembly consists of a graphite

Jan 1, 1970

By K. A. Natarajan

Platinum electrodes are not inert as originally thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g., in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measurements in water-oxygen, iron-water-oxygen and manganese-water-oxygen systems. Stability relations between Fe++ and Fe(OH)3 and between Fe(OH)2 and Fe(OH)3 were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions.

Jan 1, 1970

By J. M. Glass, C. D. Sholtess

We at Hughes Tool Co. are extremely proud of the quality of the hardware and techniques introduced through our efforts in tunnel-machine development and of the ready acceptance of them by manufacturers and contractors throughout the world. All of us who attended the conference and who are represented in the book, we believe, anticipate an increasing need for improved methods of underground excavation. The development of such methods will permit the further exploitation of our underground resources plus providing underground space for transportation and habitation at a rate compatible with demand. We hope that our comments, derived from the application of Hughes Tool Co.&apos;s rotary boring experience, may provide a better understanding of the boring method as a possible avenue through which the desired improvement in underground excavation may be attained. We hope you may also become aware of some of the problems Hughes, as a pioneer developer of raise, shaft, and tunnel-boring equipment, must face prior to further major undertakings in this very interesting field. Our task is to acquaint you with the present status of the Hughes Tool Co. development program as it relates specifically to tunnel-boring machines. We feel this task can best be accomplished by a brief review of the general sequence of events leading to and constituting an equipment development program and more specifically the manner in which these events have occurred to either influence or further our boring-machine development program. The development of a machine to accomplish a certain function or series of functions is usually a very long and tedious process to which any number of individuals must contribute, perhaps over a period of centuries. Of particular irony is the fact that often those who contribute most generously do not necessarily reap the greatest immediate benefit. A marketable ma- chine will, however, result from a sequence of events such as these: 1) A problem or need is defined. 2) An idea is born to eliminate the problem.

Jan 1, 1970