Search Documents

By Joseph D. D?Annunzio

The report on cut and cover construction as assembled by the Organization for Economic Co-operation and Development covered 17 different countries based on a total of just under 400 individual replies of which about 30% of the replies were from the United States. In general, the review of replies to the questionnaire led to the impression that cut and cover construction is a very inadequate method which needed many improvements. This unfavorable judgment, however, resulted in the manner in which questions were asked rather than in the method itself, It can be concluded that the cut and cover construction method has proved itself as an excellent method and that it has reached a high degree of technological perfection, but inadequacies stilt exist, and for purposes of complete evaluation, comparisons with mining tunnelling methods should be carried out. The principal problem in cut and cover construction is the interaction during construction between the construction process and the existing use of the surface and subsurface environment. The greatest impediments to cut and cover construction have little to do with the physical works being constructed, but more with creating a site in which the work can be performed. Utility relocation, traffice maintenance, and protection of existing structures are major problems for the construction contractor, and too frequently receive insufficient attention in preconstruction planning and design. Some OF the areas in which research should be undertaken are as follows:

Jan 1, 1970

By E. Ryba, D. J. Michel

SAMPLES of REZn2 (RE = rare earth) intermetallic compounds prepared by a variety of techniques have been shown to exhibit an extensively twinned micro-structure.1-4 We have recently conducted compression tests at room temperature on specimens of HoZn2 prepared by a powder metallurgy technique.' The microstructures of specimens before and after testing are shown in Fig. 1. The "before" specimen, Fig. l(a), shows the basic twin structure of this material. Fig. l(b) shows the microstructure of the "after" specimen just below the fracture surface and reveals considerable cross-twinning as well as additional

Jan 1, 1970

By James E. Lawver, James L. Wright

This paper describes the design of a cell used to measure the electrical conductivity, or the reciprocal resistivity, of granular materials. It also establishes a quantitative relationship between the electrical conductivity and the electrical separation of selected mineral samples. It is estimated' that the free world produces about 13 million tons of mineral concentrates a year by electrostatic or electrodynamic methods. At least 95% of these concentrates are produced by corona discharge type machines that separate minerals by exploiting the differences in their electrical conductivity. But, what is meant by the electrical conductivity of a mineral? How large a difference in the electrical conductivity of two mineral species is necessary to effect a separation? Just what is the role of conductivity in electrical separations with regard to capacity and selectivity? There is a considerable amount of information in the literature on both the mechanisms of conduction and the values of the electrical conductivity of pure single-crystal mineral specimens. In addition, some insight into the role of mineral conductivity can be obtained by referring to a Bureau of Mines publication' in which 95 minerals have been grouped as conductors or insulators as a function of temperature. The classification was made on the basis of the percent of weight that reported as "conductors" in an electrical separator. But, as is often the case in the mineral industry, practical application leads theory — and there is little useful information in the literature giving any kind of quantitative relationship between electrical conductivity and electrical separations. The problem is a bit complex because electrical conductivity per se — which can be rather easily measured on large, single grains — is not sufficiently informative to permit quantitative predictions of the separability of the mineral system. Practical "high-tension"* separations are made at such feed rates that the band of minerals on the rotor is multilayered in thickness. Thus, the effective conductivities of minerals as seen by a high-tension machine include particle-to-particle contact resistance, which is often a controlling factor in making a separation. This is particularly true when the mineral grains are coated with slime or with a dielectric surface film. From a high-tension separation viewpoint, one is actually concerned with the time required for corona-charged grains to lose enough charge so that the centrifugal force acting on the particles exceeds the image force holding the grains to the rotor. This calculation requires a knowledge of the effective mineral conductivity s. (The conductivity of the metal rotor is sufficiently greater than that of the minerals so that it need not be considered in charge decay calculations.) The charge density at time t can be approximated by the relaxation equation.3 where t 5 charge density at time t r, - charge density when t = 0 cr e total electrical conductivity £ = permittivity The time required for the charge density to fall to l/e of its initial value is called the relaxation time and is numerically equal to €/n. AS defined here, u is the conductivity of an element of homogeneous grains making contact with each other and with a grounded rotor. This paper deals with the design of a conductivity cell used to measure a, or its reciprocal p, the electrical resistivity. CELL DESIGN Initial test work was performed with a cell recommended by ASTM.4 Since the reproducibility with the ASTM cell was not satisfactory, it was decided to

Jan 1, 1970

By L. J. West, R. M. Perrry

This chapter describes the rock mechanics studies performed for a high cut at a nuclear power station in Pennsylvania. Two units presently are being constructed on the Susquehanna River. When these units are completed, they will generate approximately 2100 MW of electricity. It was necessary to excavate about 1 million cu yd of rock to prepare the site. This excavation resulted in a high cut on the west and north sides of the station area with a maximum height of about 200 ft. The location of the high cut with respect to the plant facilities is shown on Fig. 1. The recommended slope angles ranged from 1 ½ (horizontal) to 1 (vertical) for the upper residual soil to ½ to 1 for the deeper competent rock. Because of the significant height of this cut and the fact that the slope is immediately adjacent to the proposed nuclear facilities, extensive stability analyses were performed prior to, during, and after excavation to evaluate the steepest angle at which the slopes could be safely cut. The studies consisted of evaluating both qualitatively and quantitatively all apparent factors which could affect the stability of the slopes. These factors include the strength of the material, the zones of weak material which are present along the planes of schistosity, the prominent joint systems, the ground water, and postulated seismic effects. FIELD AND LABORATORY STUDIES A comprehensive program of field explorations was performed to evaluate the geologic characteristics of this site. This program consisted

Jan 1, 1970

By J. R. Emery, D. F. Coates

"FOUR PAPERS ON CEMENTED BACKFILL were given at the Annual General Meeting of The Canadian Institute of Mining and Metallurgy in 1970:Weaver, W. S., and Luka, R., ""Laboratory Studies of Cement-Stabilized Mine Tailings"".Pasieka, A. R., Beattie, H. F., and Espley, G. H., ""Cemented Hydraulic Backill within the Falconbridge Group of Companies"".McLeod, P. C., and Schwartz, A., ""Consolidated Fill at Noranda Mines Limited (Geco Division)"".Clement, W. P., and Sokoloski, R., ""Pumping Cemented Backfill"".These four papers give the impression of a development in mining technology that has been substantially completed. Somewhat over ten years ago, The Inter-national Nickel Company of Canada, Limited and Falconbridge Nickel Mines Limited started experimenting with the addition of Portland cement to mill tailings to produce improved backfill and cheaper floors for scraping. Shortly after, the Canada Cement Company Limited (now Canada Cement Lafarge Ltd.), with full support of the two mining companies, started an extensive research program to provide the technologic-al data necessary to exploit what was obviously going to be a significant development in mining technology."

Jan 1, 1970

By John R. Zelonka

Models made by encasing strain-gage networks in epoxy are described and evaluated. With this technique relatively complex models can be constructed in which any number of gages can be located and alined precisely. Although the gages are an integral part of the model matrix, they create no important mechanical or thermal stresses. Model construction techniques and experimental data proved reproducible and reliable. In addition, the sGlution obtained with these models to the problem of the state of stress around a circular hole in a plate subject to a plane stress condition was in agreement with theoretical, photoelastic, and finite-element solutions.

Jan 1, 1970

By John R. Keith

Lead and zinc contents of elm, maple, and oak trees and of soils in which the trees grew were determined in samples from the Upper Mississippi Valley mining district, and from an area outside but contiguous to the district. The lead and zinc analyses of plant materials served to differentiate the mineralized and nonminer-alized areas. Stems contained about two times as much lead and about two to five times as much zinc as did leaves taken from the same stems. Lead and zinc analyses of all soil horizons could be used to differentiate between the two areas. Soils at most sample sites in the mineralized district seemed to be more reliable than plants for geochemical prospecting and are a more practical sampling medium. Soil samples from areas with thick loess cover, however, failed to indicate the presence of mineralized bodies whereas tree samples from the same sites contained anomalous amounts of lead and zinc. It is suggested that in areas of thick loess cover, plant samples could be used in prospecting for lead and zinc. The important part that plants play in the cycling of elements through the soil horizons is well-known. The concentration of elements in the upper soil horizons by the action of plants has been called the Goldschmidt enrichment principle.' The fact that plant species vary greatly in their ability to concentrate particular elements in their tissues is also well-known.' Agricultural literature has dealt extensively with relationships of the major nutritive elements in soils and plants3 The extent, however, to which plant actions cycle the minor nutritive and the nonmetabolic elements in the soil has not been adequately investigated. Lead is non-nutritive and toxic to plants, whereas zinc is a micronutrient in low, but toxic in high, concentrations.4 This report presents the results of a biogeochemical study concerned with the amounts of lead and zinc in some plants and soils that occurred both within and adjacent to the Upper Mississippi Valley lead-zinc district. Field work for this study was done in the summers of 1961 and 1962. SAMPLE TARGETS AND CHEMICAL ANALYSES Geologic and physiographic descriptions of' the district have been made by Heyl 5 and several other authors in a series of U.S. Geological Survey (USGS) reports and quadrangle maps.6-I Sedimentary rocks, mostly dolomite, limestone, shale, and sandstone, of Cambrian, Ordovician, and Silurian age predominate in the area. Mineral deposits are of the vein and cavity-fill type; the principal ore minerals are galena and sphalerite. Vegetation of the area was characterized by Curtis1 6 as southern hardwood forest interspersed with patches of oak savanna and prairie. Plant genera typical of the eastern United States Temperate Zone, including ash, cherry, dogwood, elm, hackberry, hickory, maple, oak, and other woody and herbaceous genera, are present. The natural vegetation has been greatly modified by agricultural, logging, and mining operations. The species of the original flora are present, but not in their former relative abundance. Soils of this district belong, for the most part, to the Brunizem and Gray-Brown Podzolic great soil groups. The Brunizems are the soils developed under prairie vegetation.'' The Gray-Brown Podzolics are the soils developed under deciduous forests,18 They are derived from both bedrock and from loess parent materials, and

Jan 1, 1970

By Pierre Dosmond

In ore mining technology, the loading and hauling operations are undoubtedly the area where the most spectacular progress has been made during the last twenty years. I shall draw some examples from the Eastern France iron ore mines which I how well and whose production of 62 million tons for 1962 and 1963 constitute a worthwhile experience worldwide. The iron ore deposits of Lorraine are of sedimentary origin. They contain many mineralized horizons with workable seams situated from 330 to 830 ft. in depth. The dip of these seams is generally less than six percent. Their thickness varies from 6 to 23 ft. All seams are not workable throughout the whole area of occurrence, but in some mines there are five mineable seams in the same vertical section, with from 5 to 20 ft. of barren ground intervening between them. The iron content of the mineral varies from 28 to 36 percent. Specific gravity of the ore is 156 lb. per cu. ft. m place and 100 lb. per cu. ft. blasted. Reserves of iron ore in the Lorraine region are estimated at six billion tons with an iron content of more than 28 percent. These mines operate by means of rooms and pillars process, with pillar robbing; the final recovery is very good and averages 90 percent. Some years back, competition from richer, imported ores incited these mines to make constant efforts to increase their productivity and reduce mining costs, thus placing them in a leading position in mining technology, as evidenced by the dramatic evolution of their output per manshift (Figure No. 1).

Jan 1, 1970

By J. E. Hanafee, G. J. London

MANY studies of the deformation behavior of materials under a superimposed hydrostatic pressure have shown that materials brittle at ambient pressure behave in a ductile manner under pressure. Thus, with a metal such as beryllium which possesses relatively low ductility, but otherwise exhibits quite useful physical and mechanical properties, hydrostatic pressure may be particularly useful for both forming beryllium shapes and studying its deformation behavior. In fact, it has been found1"4 that polycrystal-line beryllium in both ingot and powder form appears to behave in a more ductile manner on a macroscopic level in a hydrostatic pressure environment, and it has been suggested2 that this is due to activating a new slip mode. Furthermore, Andrews and Radcliffe5 have found pressure induced nonbasal dislocation activity in hot pressed beryllium. Recently6 it has been shown in "c-axis" compression tests under hydro-static pressures up to 28 kbars that the shear stress needed to cause slip with a Burgers vector out of the basal plane (pyramidal slip) does not change with increasing pressure in beryllium with a purity of some 99.5 pct. This material is equivalent or more pure than the beryllium used in the previous pressure studies. Thus, it appears, as suggested by Inoue et al.,3 that the hydrostatic pressure affects the fracture stress rather than the stress necessary to activate pyramidal slip in beryllium. However, in "c-axis" pressure tests on high purity 12 zone pass beryllium (˜50 ppm total impurities) the macroscopic compression stress needed to cause pyramidal slip was considerably lower than that at ambient pressure.6 It has further been shown that alloying beryllium with nickel and copper in the range 2-5 wt pct also favors the occurrence of pyramidal slip in "c-axis" compression tests,7'8 while lower amounts of nickel and copper do not have significant effects. In the present study the combined effect of hydrostatic pressure and alloying high purity beryllium on the shear stress needed to cause pyramidal slip has been ascertained. A 2.5 wt pct Cu alloy was selected as the first alloy to study as this level of copper did favor pyramidal slip at room pressure. A high purity (12 zone pass) single crystal of beryllium 0.3 by 0.1 by 0.1 in. was cut and polished by an orientation and lapping technique8 so that the top and bottom compression surfaces were parallel and within 3 min of arc to the (0001) plane and the sides parallel to the {l010} and {ll20} planes. In these compression specimens, therefore, the resolved shear stress was nearly zero on both the basal and prism planes, and slip was restricted to pyramidal systems. Analysis of slip traces on the two lateral surfaces served to accurately identify the active slip planes.6'9 The pressure unit was a modified piston-cylinder device fitted with a manganin transducer coil arrangement which continuously monitored and recorded the hydro-static pressure. The load on the specimen was measured by a strain gage load cell which operated entirely within the pressure chamber. This load cell was calibrated before and after each pressure cycle at room pressure in situ and the calibration did not vary more than ±1 pet. These techniques and devices have been previously described in more detail.6 Successively higher compressive stresses were applied to the single crystal under a superimposed hydrostatic pressure until fracture occurred. The strain rate was (4.5 ± 2.0) x 10-6 sec-1 and the average rate of pressure application and release was approximately 0.3 kbars per min. As the load on the specimen was applied by the piston which was used to increase the hydrostatic pressure, the pressure increased during the compression test. This increase ranged from 0.0 to 0.8 kbars, and the maximum hydrostatic pressures are quoted in Fig. 1. The lateral surfaces of the specimen were examined in a light microscope after each pressurization/stress cycle so that the stress at the onset of {1122} pyramidal slip could be ascertained. Post compression height measurements allowed the plastic strain in the specimen to be evaluated to within 0.03 pct. The resulting compression stress-plastic strain curve is shown in Fig. 1 with results of a "c-axis" test on a similar Be-2.5 wt pct Cu single

Jan 1, 1970

By H. E. Cline, E. F. Koch, J. L. Walter

It has been postulated and, in a few instances shown, that some kind of dislocation structure will be present at semicoherent interfaces to accommodate small lattice mismatches. In the present study of the NiAl-Cr eutectic, regular arrays of interface dislocations are observed at the boundary between the chromium-rich rods and the NiAl-rich matrix. The networks were examined by transmission electron microscopy and selected area diffraction. The rods and the matrix have a crystallographic relationship in which all directions and planes of the two phases are parallel. The dislocation networks are cmposed of a<100> dislocations lying on the intersections of the cylinders with (100) planes. Dislocations forming hexagonal rather than square arrays are also observed at certain areas of the network. The morphology of the network is consistent with the interpretation of mismatch being accommodated by interface dislocations in the cylindrical geometry. The measured spacing between dislocations was used to calculate an apparent lattice mismatch between the phases (˜0.35 PCt)interface network energy (-140 ergs per sq cm), and network strengthening (-10,000 psi). It has been proposed by Frank and Van der Merwe1 that dislocations should be present at the boundary between two semicoherent crystallographically related phases. The role of the interface dislocations would be to reduce the internal stresses, caused by the mismatch in atomic spacing across the interface. Such dislocations have been observed at the interface between expitaxially grown films and Substrates.2-4 Interfacial dislocations have also been observed at precipitate-matrix interfaces.&apos;-&apos; Directionally solidified eutectics have been shown to have semicoherent phases1&apos; and would, therefore, be expected to have interfacial dislocations as found by Weatherly at a lamellar fault in A1-A12Cu.11 The NiAl-Cr eutectic appeared to be a promising system to examine because both phases are cubic, the lattice mismatch is small, and the phases are crys-tallographically related. Furthermore, the eutectic is easily thinned for transmission microscopy. Indeed, interfacial dislocations were observed and this report describes the nature of the dislocation networks in the boundary between the NiAl-rich ma-trix-phase and the fine chromium-rich rods.21 I) EXPERIMENTAL PROCEDURE Ingots, 3/4 in. in diam and 6 in. long were made by melting in vacuum and casting under argon using 99.9 pct pure material. The composition, in at. pct, was 33 pct Ni, 33 pct Al, and 34 pct Cr. The ingots were then placed in A1203 crucibles on a water-cooled base, melted by means of induction, and withdrawn from the hot zone at the rate of 1 in per hr under argon.* * T his material was first directionally solidified in this laboratory by E. R. Stover Slices were taken perpendicular to the growth direction of the directionally solidified ingot for metallography and for transmission electron microscopy. The electron transmission samples were thinned mechanically, then thinned electrolytically in A-2 electrolyte* *A-2 electrolyte: 62 ml perchloric acid, 700 ml ethanol, 100 ml butylcellosolve, 137 ml distilled H20. until a hole appeared in the foil. 11) EXPERIMENTAL RESULTS A) Optical Microscopy. The microstructure, viewed on a plane perpendicular to the growth direction, is shown in Fig. 1. The structure consists of cells or colonies of parallel chromium-rich rods in the NiAl matrix. The cells occur when there are impurities present12 or, in a ternary eutectic, if the composition is slightly off the eutectic composition. The axis of the chromium-rich rods is parallel to the growth direction except near the cell boundaries. Here the rods may assume angles to the growth direction; however, examination shows that the crystallographic relationship between the rod and the matrix remains the same. Fig. 1 includes cell boundaries where the rods formed at a large angle to the growth direction. The variation of rod position across the cells made it possible to Fig. 1-Structure on plane perpendicular to growth direction. Rods near cell walls are at large angle to growth direction. Magnification 315 times.

Jan 1, 1970

By Nilsson C

Man has always been and will always be part of his environment, in ,a good, bad or indifferent manner. Until quite recently, this environment has been the atmospheric boundary layer above the land masses, and to a limited extent the air-sea interface of the oceans. Since the days when he lived in caves, he has built up a wealth of observations on these two environments,-with ever-increasing scientific precision which unfortunately until quite recently was completely insufficient for modern capabilities of data analysis. Consequently, in a sense, he has left in his wake thousands of years of missed, opportunities for making exact observations and increasing his understanding. The data of the past are lost and he has to be satisfied with what he can assemble from now on when his environ- ment, largely as a result of his actions, is exhibiting more and more rapid variations in time; in other words, time series of observations of phenomena are required, the length of which is critical for most purposes of analysis.

Jan 1, 1970

By H. E. N. Stone, B. L. Daniell

This paper examines the cracking behavior on chemical reduction of three types of ore/oxide briquette mixtures. The complex sintering/hardening atmosphere was replaced by 100% oxygen and the blast furnace atmosphere by a 5/95 hydrogedsteam mixture which was used isothermally at 700°C for a constant, arbitrary time. Cracking has been assessed by measurement of reduction expansion or increase in specimen diameter as a result of chemical reduction and a subjective index based on appearance and friability. Oxidized briquettes of iron ore concentrate crack on reduction&apos;-3 in a manner which parallels the degradation of sinter in the Linder test. In the present work, the cracking behavior on chemical reduction of three types of ore/oxide briquette mixture has been studied. Firstly, LD converter fume with additions of silica; secondly, Oxfordshire ore with ferric oxide; thirdly, ferric oxide with separate additions of silica, alumina and lime. Motivation for the first-mentioned experiments lay in the improvement of the fume as furnace feed; for the second, in assessing the tolerance of a finely divided ferric oxide as a base for low melting point additions. The third series provided additional information. In this work, the complex sintering/hardening atmosphere is replaced by 100% oxygen and the blast furnace atmosphere is replaced by a 5/95 hydrogen/ steam mixture used isothermally at 700°C for a constant arbitrary time. The particular reduction conditions were known from previous experience3 to be capable of disclosing any tendency to cracking. Cracking has been assessed by measurement of reduction expansion (i.e., increases in specimen diameter as a result of chemical reduction) and a subjective index based on appearance and friability. Generally

Jan 1, 1970

By Kurt F. Weitz

"The number of materials that can be classified as fillers covers an extremely wide range: this paper outlines those fillers of the industrial mineral type that find extensive application in the paint and plastics industriesIn the paint industry, mineral fillers are known as extender pigments. Extenders are added to paint and plastic compositions to (1) lower the cost and (2) rein-force or modify the physical properties of a composition.Commonly used extenders are classified according to chemical type and discussed in terms of the change in physical properties that they impart to a paint or plastic film. Available cost reductions and data on the consumption of extenders in the Canadian paint industry are also included."

Jan 1, 1970

By Allen L. Hatch

A survey of all phases of the world&apos;s lead and zinc production in 1968 from ore through to refined metal was conducted by sending questionnaires to individual companies ad the results of this survey are tabulated at the end of the paper. The paper goes on to review changes in the geographical distribution of the world&apos;s lead and zinc mine and metal production and in the trading patterns of raw materials, present and future utilization of metal production capacity, developments in metal smelting and refining processes and the growing importance of marketing, product development and research in the 1950&apos;s and 1960&apos;s.

Jan 1, 1970

By Douglas D. Donald

The financial analyst&apos;s job is to make an objective appraisal of the investment opportunities which exist within the various industries under his supervision within the context of the economic model provided by his firm and the a climate of investor sentiments. Industry analysis is critical. When a major investment trend develops, usually the stock of all companies within the specific industry react in the same direction. I should emphasize here, however, that an investment trend is influenced by the economic outlook, but economics is not the only determinant - investor psychology and arbitrary political factors may be of equal or greater importance. Part of our job is to recognize trends early and determine whether they are valid. Following industry analysis, the analyst must examine the specific companies within that industry since some companies usually react more violently than others to industry trends, whether they be favorable or adverse. To simplify the process of evaluating an investment opportunity, it is convenient to isolate three types of factors which have a bearing on every sort of business although the degree of influence of each factor may vary from industry to industry. These categories are, 1) independent or external factors insofar as they are beyond the control of corporate management, 2) interdependent factors insofar as influence may be exerted by industry-wide action, and 3) dependent factors covering the area of internal decisions which are basically under the control of the individual corporate managers. Although the title of this paper, "The Corporate Use of Cash Flow," is only one segment of the third category, it may be useful to continent on the first two categories as well. The independent factors may be either economic or governmental. The economic factors include cyclicality which may be very high in the case of the basic commodity industries or relatively low as in the case of utilities. Underlying growth rates, another independent factor, may range from the business equipment industry with an annual growth rate of 14% through the electric utility industry with a growth rate of about 7% per year to the

Jan 1, 1970

By D. O. Hobson, P. L. Rittenhouse

We have recently found that many lots of Zircaloy-2 and -4 tubing tested in tension deform to cross section shapes that are "polyhedral" rather than circular. The noncircular cross sections seem to result from a circumferential variation in plastic proper -ties and, therefore, in texture. We examined the diffracted X-ray intensity from (OOOl), {1010), {ll20}, and {1011} planes parallel to the tubing surface around the entire circumference. Tubing that deformed to a circular cross section showed <5 pct variation in diffraction intensity around the circumference from any of these planes. Greater intensity variations were found for all the tubing materials that developed non-circular cross sections during deformation. In each instance the number of intensity maxima and minima was consistent with the number of sides of the &apos;polyhedral" cross section. THE effects of crystallographic texture on the mechanical properties of zirconium, zirconium alloys, and other anisotropic hexagonal materials such as titanium and hafnium have been intensively studied. If the natural crystallographic anisotropy of these materials could be controlled by selected fabrication operations, a material could be produced with a texture, or preferred orientation, in which the maximum strength directions are in the stress directions of the structure. The permissible stress levels of the structure could then be increased. Rittenhouse and Pickle-simerl have shown that highly textured Zircaloy-2 plate can vary from 52,000 to 70,000 psi in tensile yield and from 62,700 to 122,000 psi in compressive yield strengths as a function of specimen orientation. Similar texture effects have been observed in Zircaloy tubing, whose mechanical properties differ depending upon whether the tubing has basal poles predominantly radial or tangential and upon the mode of testing. These same texture effects might be troublesome if the texture in the tubing is not uniform around the tube walls. This paper is concerned with the effects of nonuniform texture on the strain behavior of commercial Zircaloy tubing. BACKGROUND Previously, various lots of commercial Zircaloy tubing were tested under selected stress conditions as part of a program to determine the four quadrants of the yield locus. One of the testing procedures was uniaxial tension and it is the influence of texture variations on the tensile deformation behavior of the tubing that is of interest here. The effect of texture on the strain behavior in tubing is very apparent from a uni-axial tensile test.2 This behavior is illustrated schematically in Fig. 1 for three different tubing textures: 1) basal poles predominantly in the radial direction; 2) basal poles predominantly in the tangential direction, and 3) basal poles equally distributed between the radial and tangential directions. In the first example most of the grains are oriented for prism slip to operate to allow axial lengthening and diametral reduction of the tube. Reduction in wall thickness requires {1122} twinning, a more difficult operation than slip.* In the second example, the texture is such that *The singleCrystal analogy will be used quite often in this paper when strong texturesare being discussed. The textured material is assumed to react as if it were a single crystal aligned in the same orientation and under the same stress system as the predominant texture._____________________________________________ prism slip operates to give axial lengthening and wall thinning. Diametral reduction requires twinning and again should be more difficult to accomplish. A specimen with basal poles equally distributed between the radial and tangential directions should exhibit about equal diametral and wall strains.* Table I shows the *Diametral strain is accomplished by a combination of circumferential and longitudinal strains. But, for the purposes of this paper, it will be considered as a strain causing a change in the length of a specified diameter.__________ strain behavior of two lots of tubing with different textures. The first tube has a texture with basal poles equally distributed between the radial and the tangential directions. The ratio of true thickness strain to true diametral strain is almost unity. The second tube has a predominantly radial basal pole texture and it is apparent that most of the total strain has occurred by diameter reduction, just as one would predict. There is over three times as much diametral strain as thickness strain. RESULTS We found that specimens from certain lots of commercially fabricated tubing did not retain round cross sections during uniaxial testing. Instead, the speci-

Jan 1, 1970

By F Kelly

"A central composite experimental design was used to determine empirical relationships between the operating variables of a ball mill and the characteristics of the ground products. The independent variables selected for the study were the work index and size distribution of the feed material, the feed rate and the pulp density. The measured responses included product size distribution, product surface area, viscosity of pulp discharge, weight of dry solids in mill, mill time constant and emitted sonic vibrations. The ball mill was operated continuously in open circuit during each experimental run.Multivariable regression techniques were used to derive linear empirical models from the experimental results. Of the four factors studied, the grindability of the feed material significantly affected every measured response. The size distribution of the ground product was affected significantly by the feed rate and the size distribution of the feed, but not by the pulp• density. Feed throughput capacity and pulp density were significant to the viscosity of the pulp discharge, the weight of solids in the mill and the mill time constant. Significant first-and second-order models are given for the above relationships. The relation-ships between the characteristics of the sonic vibrations of the operating mill and the various dependent variables have not as yet been established."

Jan 1, 1970

By H. E. Cline, D. F. Stein

A fine lamellar structure with interlamellar spacings ranging from 0.I to 3.7 was Woduced by high-speed directional solidification and used to study the interaction of dislocations with an array of bimetallic bound-am.es. The tensile flow properties were measured at elevated temperatures and the results interpreted in terms of an image force model. As the width of the plates decreases the strength increases according to a Hall-Petch relation, suggesting pile -ups. Considerable strengthening was also observed at elevated temperatures. In recent years composites containing a strong but brittle phase and a ductile but weak phase have been studied extensively in the search for a high-strength material with adequate ductility.&apos; However, the strength of these composites has been limited to a volumetric average of the strengths of the component phases. In this paper we will show that a composite made by directional solidification of a Cu-Ag eutectic has strength properties that substantially exceed the strength of either of the metals in the composite, and an explanation for this increased strength will be presented. The Cu-Ag eutectic is a near ideal material to study for several reasons. The eutectic structure is made up of alternate plates of silver-rich and copper-rich phases with the same crystal structure.2&apos;3 In addition, the mechanical and elastic properties of silver4 and copper5 are known over a wide range of temperatures and the eutectic microstructure is stable to nearly the melting point.6&apos;7 Therefore, the properties of the eu-tectic are readily comparable to various theories involving the mechanical properties of copper and silver. The experiments consisted of producing directionally solidified Ag-Cu eutectic material, determining the structure and performing tensile tests at different temperatures and strain rates. EXPERIMENTAL A) Solidification and structure. A cylindrical ingot 2.2 cm in diam and 15 cm long was prepared from 99.999 pct pure materials and cast in argon. The ingot was placed in an alumina crucible and was direc-tionally solidified at 7 x 10"4 cm per sec in a Bridg-man apparatus in argon. Metallographic examination at both ends and along the length of the ingot showed a uniform structure that consisted of fine alternate plates of silver- and copper-rich phases. The plates were aligned parallel to the growth direction, as shown in the longitudinal section, Fig. 1, and were in small randomly oriented domains of parallel plates as viewed in a transverse section, Fig. 2. Four smaller ingots 0.175 in. in diam were solidified at speeds of 2Xlo-&apos;, 4.4 xlo-&apos;, 4.4 x 10-3, and4.4x10-4 cm per sec to produce a range of lamellar spacings. Replica electron micrographs were taken to resolve the individual plates as shown in Fig. 3. The copper-and silver-rich plates in the larger ingot were about

Jan 1, 1970

By John E. Husted

Universities have education as their primary purpose. This appears to be an innocuous statement with simple meaning. In an age of conflicting semantics, however, cords and meanings are often lost or changed. The term education is often broadly expanded to encompass any form of learning process, or the accumulation of knowledge, and even to the beneficial application of knowledge to man&apos;s problems, hence one find that education in universities is not solely the formal process of texts, lectures, recitations, and testing by a batch process known as class room teaching. Despite critics of education batch is spelled with an "a", instead of an "o" - at least we hope so If one defines teaching as causing to learn, then the learning objectives may necessitate a variety of approaches within the teaching concept and research is among those favored at the graduate and some undergraduate levels. Research has been among the glamour words and certain fields such as oceanography and space science have had more than their share of glamour. Unfortunately, industrial mineral research has not had the competitive drawing power of enamoring students of the "note" generation in terms of glamorous accomplishment. Research today usually requires sophisticated equipment and such equipment is expensive, both for initial purchase and operation. Again, administrations, be they industrial, government, or academic, usually require

Jan 1, 1970

By James H. Russell

Alkalized alumina (an active form of sodium aluminate) has been considered as a sorbent for the removal of sulfur dioxide from industrial flue gases. Four rate equations, each based on a different mechanism, were compared with the results of thin-bed sorption tests. It was found that each equation agreed with the experimental results, within experimental variance, over most of the range of sorption studied. First-order rate equations were generally satisfactory in explaining both sorption and regeneration. It is concluded that the equations developed are adequate for the design of commercial fluidized beds for the sorption of SO2 from industrial flue gases and regeneration of the alkalized alumina.

Jan 1, 1970