Search Documents

By E. Hoek

INTRODUCTION Rock slope stability research has been in progress for the past four years at the Royal School of Mines in London under the sponsorship of a consortium of 23 companies* with interests in open pit mining. This paper reviews the principal aims and achievements of this research project. In order to assist the reader in following these details, the basic philosophy underlying the formulation and direction of this research project is discussed. DISTRIBUTION OF RESPONSIBILITY In open pit mining, the economic necessity of keeping waste rock removal to a minimum generally means that the mine slopes have to be excavated to the steepest possible slope angle. On the other hand, excessive steepening of these slopes can induce failures, which may negate the economic benefits that have been aimed at and which may also result in loss of life and damage to equipment. Consequently, where slope failures are likely to prove to be a problem, an evaluation of the stability of the slopes to be created should be included as part of the overall pit design. How is the stability of a rock slope evaluated? When this question was examined, during discussions on the research policy to be followed at the Royal School of Mines, it was clear that relatively few satisfactory techniques were available in a form that would be comprehensible and therefore useful to the practical mining engineer. It was recognised that the research project must be directed towards two distinct aims: a) The evaluation of existing techniques for rock slope stability analysis and the provision of new techniques where these existing methods were found to be inadequate and b) The presentation of the results of this evaluation and research in a form that would be useful to engineers without specialist training in rock mechanics. It was soon realized that a university based research team, however large and efficient, could not achieve these aims without the co-operation and assistance of mining engineers,

Jan 1, 1972

By Ritchie AS

The principles of chromatographic and electrophoretic separations are described in simple non-mathematical language. Brief details of the analytical procedures and of equipment are given. Partial analyses of rare earth elements in monazites from four localit- ies in New South Wales are compared with analyses from other localities. The presence of uranium in two of the monazites is recorded. The occurrence of rare earths in nature is outlined and its geological significance is indicated, A low capital cost method of analysis of rare earths in monazites is Introduced.

Jan 1, 1972

By James Douglas

For the past several years, inflation has placed increasing pressure on our economic system. The total effect of inflation is complex when combined with other factors which affect the economics of equipment. A mathematical model is described herein which can be programmed on a computer to determine the effect of inflation on economic life and profits after taxes. The computer output results in graphic plots which clearly show the relation of various percentages of inflation to life and profits. Inflation has become a common topic of conversation in the recent past. What is it and how can it be measured? What effect does increased inflation have on equipment policy? Research now in progress at the Construction Institute at Stanford University is beginning to unravel some of the mystery of inflation. As a start, let us answer the first question by defining the word inflation. The dictionary says that inflation is "an increase in the volume of money and credit relative to available goods resulting in a substantial and continuing rise in the general price level. It appears, in fact, that we are in an inflationary spiral which is "a continuous rise in prices that is sustained by the tendency of wage increases and cost increases to act on each other." 3 Inflation behaves just like compound interest. It takes more dollars of future years to buy an equal amount of a given commodity, be it a material or a service. Let us assume an annual inflation rate of 5 percent. Assume that 1Associate Professor of Civil Engineering, Stanford University, Stanford, California. 2Webster's Seventh New Collegiate Dictionary, Springfield, Mass., G. and C. Merriam Co., 1969. 3Ibid.

Jan 1, 1972

By A. J. Strazisar

The Bureau of Mines conducted a laboratory investigation to study the effectiveness of low-pressure steam and water spray in suppressing respirable dust at the tips of a saw-type cutting wheel. Suppression efficiencies were found to be proportional to the amount of the water or steam applied at the cutter tips. For equivalent water output rates, a maximum efficiency of approximately 80 percent was reached for both steam and water spray. Results from the steam and water spray tests showed an increase in suppression efficiency with an increase in particle size of 1 to 8 micrometers. The data indicate no advantages for using steam as a dust suppressant.

Jan 1, 1972

By A. Becker, C. Gauvreau, L. S. Collett

"A scale model was designed to simulate the airborne Barringer INPUT time domain electromagnetic system. The amplitude of the response to a vertical conductive dyke varies considerably with the conductor's thickness conductivity product (TCP). The response increases from a minimum detectable level at a TCP of about 2 mhos, rises to its maximum value at a dyke TCP of 15 mhos and then falls again so that conductors with a TCP exceeding 500 mhos would probably remain undetected. Measurements made with both standard receiver coil configurations (maximum or minimum coupled) indicate comparable effectiveness for both systems, either from the viewpoint of vertical conductor detection or from the viewpoint of discrimination against overburden anomalies."

Jan 1, 1972

By R. V. Higgins

A numerical method is presented to calculate the pressure distribution in a petroleum reservoir that has irregular boundaries. The computer program is straightforward and requires minimal data preparation. The method can also be used to determine pressure distribution in many other types of underground reservoirs. In this method, the grid solution of the fluid-flow equations in a reservoir that has regular boundaries (previously published) was expanded to handle irregular boundaries. The computer program locates grid points at the irregular boundaries. The method of mirror images is then used to form a special stencil to determine the pressure at each of these points. Two examples are presented to demonstrate the applicability of the method for virtually any reservoir configuration.

Jan 1, 1972

By J. Graham Eby

"This paper describes the development and some typical applications of Wemco's large-capacity flotation machines, the No. 120 and the No. 144, with volumes of 300 and 500 cubic feet, respectively. During the 1960's, it became obvious that low-grade orebodies would be mined at high tonnage rates - plants and grinding mills would be larger, which would create a demand for larger flotation equipment. To meet this demand, Wemco developed a single-mechanism, 300-cubicfoot cell, having five times the volume of the standard No. 66 cell. The average production rate of the No. 66 cell on porphyry copper ore was 100 tpd per cell; and it was our intention that the No. 120 (300-cu. ft) cell would handle 500 tpd per cell, with at least equal metallurgical results and power consumption per ton. The success and industry acceptance of the No. 120 cell has since led to the development of a larger cell, the No. 144, having a volume of 500 cubic feet."

Jan 1, 1972

By I. R. Jonasson, R. W. Boyle

"Current interest in the distribution of mercury in the natural environment comes from quite different, though not unrelated, sources. Mercury has long been an important metal in many industries and has, therefore, been much sought after by mining interests. The presence of mercury traces in the various media of the natural environment, namely soil, rock, air, water and vegetation, is exploited by geochemists not only to find mercury and polymetallic ore deposits, but also to find most other types of economic metal mineralization. More recently, however, mercury has caught the attention of health authorities and environmental scientists who are becoming increasingly concerned over the hazards of mercury wastes and the danger these present to the environment and to man. It is now apparent that the trace quantities of mercury, considered so important and helpful to exploration geologists, can be concentrated in the biosphere to such levels as to present considerable problems for ecologists. This article summarizes most of the available data on mercury contents in materials of geological interest and presents average normal values for rocks, ores, minerals, soils, sediments, waters and plants. The geoch.emical cycle for mercury in nature is presented and the mechanisms of mercury migration around the cycle are discussed."

Jan 1, 1972

By Fred N. Kissell

Methane-flow and pressure data taken from a mine in the Pocahontas No. 3 coalbed are compared with flow rates from lump coal obtained in laboratory experiments. From this, it is concluded that the main source of gas is the intact coalbed rather than a "crushed zone" near the working face. The permeability and sorption capacity of the intact coalbed are calculated and gas emission rates are theoretically accounted for.

Jan 1, 1972

By F. G. Horino

This report presents the theory and design of a stiff loading machine used by the Bureau of Mines. The machine incorporates three high-strength steel columns as the restraining member in parallel with the specimen. The theory presented gives the basis of design and the dimensions of component parts of the machine. Laboratory verification of the theoretical stiffness is described using three different setups involving a hydraulic jack and spacers and confirms the stiffness calculations to within 1 percent. Experimental techniques, testing procedures, and special equipment designed for determining the complete stress-strain behavior of NX cores of both hard and soft rock are described. Typical test data are presented as force-displacement curves for two rock types, a marble and a granite.

Jan 1, 1972

By A. G. Naguib

In essence, any magnetic separator operates on the basis of imparting a preferential magnetic force on particles of higher magnetic susceptibility which are to be separated from particles of lower magnetic susceptibility. A certain amount of directional deviation to the particles takes place thus allowing for collecting each category of particles separately. The forces in action on particles in a wet magnetic separator of the established designs can be analyzed in a simple manner as shown in Figure 1.

Jan 1, 1972

By John E. Caffrey

United States Steel Corporation began mining coal in southern West Virginia at the turn of the century, and until the late 40's production was confined to underground mines. Surface mining was initiated in our southern West Virginia -holdings as a means of recovering coal that could not be obtained by underground mining methods. After observing and evaluating surface mining methods employed by other companies, some of which operated on lands of U. S. Steel on a lease basis, we undertook the establishment of a surface mining operation. Our method, as, initiated in the early 50's, remains basically the same today. Variations have come about primarily by equipment modifications. The method consists' of a pioneer cut to establish the coal outcrop, a drill bench for drilling, blasting, and removal of the overburden from the top of the coal. The land is rugged except for the flood plains of some of the larger streams. The mountains have steep slopes, averaging 30 degrees, with relatively sharp ridges and very narrow valleys,. Geologically, the coals_ lie in the Pocahontas formation of the Pottsville group in the Pennsylvanian system. This means that the coals in our area of operation lie at the base of. The coal measures in the Appalachian range. The coal that we have mined is primarily the Pocahontas nos. 3 and 4 seams. We have mined negligible amounts of other seams in the Pocahontas groups above the no. 4 seam. The Pocahontas no. 3 seam, which is the lowest mineable seam geologically in this area, lies anywhere from 700 feet below: the valley floor up to 400 feet above the floor. This is occasioned by the Anticlinal formation which gives us grades Of about 9% at the anticline, decreasing to about 1 to 1-1/2% on the extreme flanks. We have the opportunity to engage in surface mining where the coal seams intercept the surface above the valley floors.

Jan 1, 1972

A brief review of currently available "commercial" information on methods of treating ilmenite s to produce high titanium content "upgrades" is made. In this back- ground the CSIRO/Murphyores Process is described and its relationship to other methods Discussed.

Jan 1, 1972

By E. E. Malouf

For centuries small amounts of copper have been recovered from acid mine-drainage waters. In recent years, the expansion of copper-bearing waste dump leaching for copper recovery has established a technological basis that is rapidly converting the art of copper leaching' into a science. Leaching of copper, whether from copper-bearing ore or waste, follows well established chemical reactions. These reactions are commonly in an acid circuit, but where leaching of copper is to be made in rock that is a high acid consumer, ammonia and ammonia carbonate, as well as cyanide leach solutions, can be used effectively. Current hydrometallurgical processes are being applied at an ever increasing rate to recover the trace amounts of copper in copper mine waste by in-place leaching. Currently approximately 300, 000 tons of copper are produced annually in this manner where as recently as ten years ago, only one-eighth of this amount of precipitate copper was produced.. Where copper occurs as an oxide in higher concentrations as to be classified as an ore rather than waste, then the hydro-metallurgical processes are applied as percolation or agitation leaching in vats, pachuca tanks, or prepared heaps. This approach gives better control over the recovery of the leach solutions, particularly in the processes where ammonia or cyanide leaching agents are to be used.

Jan 1, 1972

By G. M. Ritcey, B. H. Lucas

In the conventional alkaline leaching of concentrate containing nickel, copper and cobalt, copper is usually removed from the system, prior to nickel reduction, by sulphide precipitation. A new process is described for the selective extraction of copper and separation from cobalt and nickel, using liquid-liquid extraction. General Mills LIX-63 dissolved in a kerosene diluent is the extractant. Trace amounts of co-extracted cobalt and nickel are easily removed by a scrub treatment, and copper is recovered from the extract by sulphuric acid stripping, thus providing a solution amenable to the oroduction of electrolytic copper. Estimated processing costs are included together with a proposed flowsheet.

Jan 1, 1972

By R. L. Schmidt

One of a series published by the Bureau of Mines covering research investigations in rock drillability, this report of field drilling results extends earlier laboratory findings and provides a relatively simple procedure for predicting percussive drilling rates with reasonable accuracy. Two percussive drills mounted on a truck were used to drill a total of 25 rock types, and the results were used to develop a prediction equation. The equation was tested on a set of unrelated laboratory percussive drilling data, and the comparison between predicted and actual rates is shown in tabular form.

Jan 1, 1972

By B. J. Scheiner

Oxidation procedures based on the chlorine-hypochlorite system were investigated for improving gold recovery from carbonaceous gold ores. The oxidation pretreatment prior to cyanidation was accomplished by (1) addition of sodium hypochlorite to ore pulp, (2) by addition of chlorine to ore pulp, and (3) by generation of hypochlorite in situ by electrolysis of a brine solution used to pulp the ore. Gold extraction of 90 pct was achieved by cyanidation of carbonaceous ore that had been pretreated with 20 Ib per ton sodium hypochlorite at 50° C for 4 hours. Similarly, pretreatment of the ore pulp with 35 1b chlorine per ton at 24° to 30° C and 15 hours reaction time resulted in 89-pct gold extraction by subsequent cyanidation. Concomitant studies showed that electrolyzing the pulp prepared with a brine solution was equally as effective as electrolyzing hypochlorite and chlorine for oxidizing carbonaceous ore constituents that are deleterious to cyanidation. Gold extraction of 90 pct was obtained by electrolysis when 275 lb of are was treated at 200 amp for 7 hours in an 8-to 10-pct salt solution. Power consumption was in the range of 60 kwhr per ton.

Jan 1, 1972

By L. A. Haas

S02 reduction with CO was studied in an integral flow reactor at a nominal flow of 0.5 liter per minute. Reactant gas contained 3 percent SO2, 6 percent CO, and the balance He. SO2 conversion was determined for three different types of catalysts. The first consisted of 16 commercial catalysts used for various chemical syntheses. Only the commercial catalysts which contained transition metals in alumina removed more than 30 percent 80a at temperatures below 510° C. Two other types of catalysts were prepared in the laboratory either by pelletizing equal amounts of powdered alumina and transition metal oxides or by impregnating commercial alumina tablets with transition metal ions. Regardless of preparation techniques, Cr and Fe in alumina were the two best catalysts. The observed results suggest that an intermediate (SCO) is formed by the interaction of surface metal sulfides and carbonyls. Alumina then catalyzes the interaction of SCO with S02 to form the end products (sulfur and carbon dioxide). Over 80 percent S02 was removed at 460° C with 2 grams alumina impregnated with 2.5 percent iron.

Jan 1, 1972

By F. Michael Wahl

With the exception of reports on commercial deposits of kaolin, fuller's earth, and other specialty type clays, there is little published information on the extent, properties, and potential uses of the clay resources of Florida. Recent studies by the Florida Bureau of Geology in cooperation with the University of Florida and the U.S. Bureau of Mines have proven the existence of two extensive Miocene clay deposits, one in peninsular Pinellas County and the other in southeastern Charlotte County. Drilling and subsequent testing of the clays from these deposits indicate their potential for economic development. Both deposits consist of montmorillonite type clays, have an average thickness of 25 to 35 feet, and are overlain by unconsolidated Pleistocene sediments. Preliminary firing tests indicate that the clays from Pinellas County are a potential raw material for lightweight aggregate production. The clay has good bloating characteristics across an acceptable temperature range with a resultant aggregate density of less than 1.00 specific gravity. The clays from Charlotte County have poorer natural bloating characteristics but might well be used after treatment or with additives. The economic potential and locations of both deposits emphasize the need for locating similar clay resources in the state that might have economic potential so that land use planning and subsequent urbanization will not prohibit their development.

Jan 1, 1972

By John H. Smith

Because of increased pressure from Federal & State Regulatory Agencies, most acid flows will require some sort of treatment prior to being discharged to receiving streams. In many industries, the volumes of liquors are large and their acid content varied. Pressure to minimize costs of waste treatment equipment and land usage makes development of a treatment process incorporating these desires mandatory. "Standard" methods of acid neutralization with lime have been known for years, however, the volume and characteristics of the resultant precipitated solids can create a disposal problem. Also, when standard lime treatment is used, the settling characteristic of the precipitated solids is normally slow. In some instances, the necessity of added dissolved solids removal, (such as iron, needing aeration) add to the problem of concentrating neutralized solids. In a paper published in the September 1970 issue of "Coal Age," *the results of extensive test work by personnel of the Homer Research Laboratories of Bethlehem Steel Corporation, Bethlehem Pa., were reported. This paper dealt specifically with development of a flow sheet to treat acid mine drainage (hereafter referred to as AMD) from coal mine operations. Regulations on discharged water required basic pH and low dissolved iron content after treatment. Liquid flows of over 9 MGD from

Jan 1, 1972