Search Documents

By Donald E. Redmon

This Bureau of Mines report reviews injury experience in the metallic mineral industries for 1966-67. For each of the years, 27 tables summarize disabling work injuries by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By Forrest T. Moyer

All general measures of the safety record of the coal mining industry worsened appreciably in 1970. Injury experience for the year was 260 fatal and 11,552 nonfatal injuries at respective frequency rates of 1.00 and 44.40 per million man-hours of worktime. The fatality total was 57 higher and the rate of occurrence was 18 percent higher than the corresponding figures of 203 fatal injuries with a frequency rate of 0.85 in 1969. The worsened fatality record in 1970 resulted primarily from a major disaster (a single accident which results in the death of five men or more) on December 30, 1970, that killed 38 men. There were no major disasters in 1969. The total of 11,552 nonfatal injuries in 1970 was the highest annual total since 1960. It was 1,635 higher and the frequency rate was 6 percent higher than the corresponding totals for 1969 of 9,917 nonfatal injuries occurring at a rate of 41.76. The injury severity rate of 8,308 days lost or charged per million man-hours was 13 percent worse than that of 7,359 in 1969. Similarly, the average severity of 183 days lost or charged per injury in 1970 was 10 days or 6 percent higher than in 1969. Aggregate worktime of 260.2 million man-hours and production of 609.8 million tons in 1970 were, respectively, 10 and 7 percent higher than in 1969. An average of 144,480 men were at work on an average of 227 active days in 6,316 mines and 544 mechanical cleaning plants during 1970.

Jan 1, 1973

By Ivor Hawkes

The purpose of the development described in this report and as stated in the contract work statement is to "design, develop, fabricate, test and demonstrate, and deliver to the government permissible low cost cylindrical stress gauges and associated components capable of measuring change of stress as a function of time in underground coal mines. The cylindrical stress gauges shall be suitable for installation in bore holes". The technique adopted for measuring rock stress changes is to preload a steel cylinder diametrically across the sides of a 1-1/2 in diameter bore hole and detect deformation of the cylinder from stress changes in the rock, by means of a vibrating wire transducer. By calibration, changes in the period (time for one wire oscillation at the natural frequency) of a high tensioned wire stretched diametrically across the cylinder in the direction of load application are related to stress changes in the rock. To completely evaluate the stress field change in the plane of the bore hole, three gauges set at an angle to each other are required.

Jan 1, 1973

The mine surveillance and communication system hereafter described provides continuous local and remote monitoring of several parameters critical to normal mine operation at each of ten underground sites in the Bruceton Research Mine. The techniques employed are well proven and have been care-fully chosen to provide the best solution to the technical problems involved while giving special attention to economic considerations.

Jan 1, 1973

By D. Randolph Berry

The objective of this program was to develop a system to extinguish coal mine fires by remote sealing of the underground passageways. The system developed had to be versatile enough to function under a wide range of operating conditions, including large variations in passageway geometry, depth of mine, water conditions, both in the mine and at the surface, and rubble in the mine passage. The system developed had to include instrumentation for the remote probing of the passageway prior to sealing, a system for sealing the mine passages, and instrumentation for remote monitoring of the quality of the seal during and after construction. These objectives were successfully achieved during this program. The remote mine sealing capability of the system was satisfactorily demonstrated in a field test conducted at the Eastern Associated Coal Corporation Federal No, 1 Mine in Grant Town, West Virginia.

Jan 1, 1973

By Donald E. Redmon

This Bureau of Mines report examines the injury experience in the quarrying industry For the years 1966-67. Twenty-eight tables for each year are presented in which disabling work injuries are summarized by department, source of injury, extent or disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

As part of the Phase I study activity, a questionnaire was sent to a representative sampling of mining companies to obtain information on the uses, use conditions, personnel policies and other user concerns associated with front-end loaders. On-site visits to several of the mining companies were also parried out and the questionnaire was used during these visits as well. Five major areas were dealt with in the user questionnaire. These included: 1) Front-End Loader Critique - An open-ended form was employed to permit the mining companies to describe the particular things they liked and disliked about front-end loaders, in general, and/ or specific models in particular. 2) Usage - A form indicating the functions performed by front-end loaders and the numbers, makes and models of front-end loaders being used by mining companies. 3) Environment - A form where the user indicated the various types of conditions encountered in their use of front-end loaders. 4) Personnel - A form for describing factors pertaining to the qualifications of front-end loader operators. 5) Miscellaneous and Comments - A form permitting the user to comment on his feelings toward standardization of front-end loader operator stations.

Jan 1, 1973

By Howard E. Parkinson

In 1969, new coal mine health and safety legislation was enacted in the United States. As a result of this legislation, the Department of Interior, Bureau of Mines has carried out communications research aimed at developing whole mine communications for increased safety and efficient operation. The research has advanced and many promising results are now being demonstrated to the mining industry. However, there remains a challenge to further improve wireless communications within the mine workings and through the overburden above the workings. The objectives for future research and development will be discussed, together with the physical and operational constraints that new mine communication systems must face.

Jan 1, 1973

By K. L. Paciorek

The aim of the present study is to determine on a gram per gram basis the toxic products of the thermal oxidative degradations of selected compositions. Four families of materials were investigated under the subject contract namely polyvinyl chloride and neoprene compositions, rigid urethane foams I and woods. Three methods were employed to conduct the thermal oxidative degradations: a sealed system (quiescent environment) I a stagnation burner arrangement (dynamic environment) I and a flow-through apparatus (dynamic I but less severe than stagnation burner conditions). The majority of tests were conducted using the first two systems; only limited experiments were carried out employing the third decomposition procedure. All decomposition was done at temperatures of 370 -4000C I the higher temperature being used in the stagnation burner. It has to be stressed that the nature of the products and the relative product concentration are temperature dependent. Thermogravimetric and differential thermal analyses were performed to supplement and extend the above delineated studies and to explore the feasibility of using these analyses as a method for material differentiation.

Jan 1, 1973

By Walter I. Enderlin

To economically extract ore from great depths in the earth while sustaining an acceptable working environment will require the development of new technology and equipment, involving large capital expenditures. Moreover, careful analysis and advance planning will be required. But, the literature is lacking in data pertaining; to the thermal properties of various host rocks and to quantities of heat generated by various underground heat sources. This types, of data is required to forecast nine heat loads during advanced planning and design. This thesis sets forth a practical method for evaluating underground sources of heat in deep mines and provides an improved information base. Moreover, seven topics for further research are recommended. The heat sources considered are: wall-rock, ground water, adiabatic compression, equipment, service lines, blasting, metabolism, curing of cement, and oxidation of sulfides and timber. Seven deep metal mines with high production rates and high heat loads were visited to obtain data necessary to assess their thermal environments. Mine records were examined, wall-roc:, temperatures were measured and a survey of the mine ventilating air and mine drainage was performed. Also, the thermal conductivity of wet and dry specimens of the host rock were measured in the laboratory. Data analysis disclosed that rock heat and adiabatic compression account for stout 60 per cent of the mine heat load at depth. Equipment currently contributes approximately 20 per cent; however, to offset increasing costs with depth, increased mechanization is anticipated. The treat from ground water averages 19 per cent and the contribution from blasting, metabolism and cement is negligible. Also, approximately [0] per cent of the increase in the enthalpy of the ventilation air is in the form of latent heat. Moisture, however, did not significantly affect the thermal conductivity of the rock specimens measured in the laboratory. Also, from the data, it is evident that a negative correlation exists between the thermal conductivity of the host rocks and the per cent of the heat load derived from the wail-rock. Furthemore, steady state heat flow renditions may be assumed in airways where there has been no major changes in the ventilation system for a period of two years or more. Under these conditions, the author found it more convenient and reliable to compute heat influx using the steady state equation for heat flow into a cylinder, rather than Carrier's method for transient heat flow, which is so often used.

Jan 1, 1973

A prototype EM Location System was fabricated and tested at the Geneva Mine near Dragerton, Utah. This system consisted of six manpack transmitters and six manpack receivers covering the frequency band from 900 Hz to 2900 Hz as well as a six channel receiver designed for use, in a helicopter. Tests showed that EM signals from lightweight (3/4 lb) transmitters could be detected both on the surface and from a helicopter through as much as 4450 ft of relatively high conductivity (2 X 10- 2 mhos/m) overburden. Furthermore, the resulting field strength profiles could be used to determine source location to within 150 ft of the actual surveyed location in the mine. Modifications were made to a Monitoring, Locating and Communications System being tested at the Bruceton Mine, Pittsburgh, Pennsylvania. These modifications have improved the performance and quality of the paging and voice telephony mode of the system. Subsurface receiver modifications have improved reception of voice downlink signals.

Jan 1, 1973

By Donald E. Redmon

This Bureau of Mines report reviews injury experience in the nonmetallic mineral industries (except stone and coal) for 1966-67. For each of the years, 23 tables summarize disabling work injuries by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By Forrest T. Moyer

In 1969, the number of fatal injuries in the coal mining industry was lower than in any previous year and the number of nonfatal injuries was lower than in any preceding year except 1968. Fatal injuries in 1969 totaled 203 with frequency rates of 0.85 per million man-hours of worktime and 0.36 per million tons of coal These rates were new annual lows. Nonfatal injuries totaled 9,917 with frequency rates of 41.76 per million man-hours and 17.42 per million tons. The severity rate for fatal and nonfatal injuries combined was 7,359 days lost or charged per million man-hours. The average severity was 173 days lost or charged per injury. These statistics represent the injury experience of an average of 133,302 employees per day working an average of 225 days in 5,955 coal mines for a total of 237-5 million man-hours worked and a coal output of 565 2 million tons

Jan 1, 1973

By G. E. Bobeck

The first year's work of a proposed three-year study of the effects of the exposure of coal mine roof rocks to the mine atmosphere has been completed. The project has been terminated. The goal of the project was to determine if possible the mechanism or mechanisms by which coal mine roof rocks interact with the mine atmosphere and weaken, and coupled with mechanical stresses, ultimately fail. The scope of the study was limited to the effects of environmental factors on the deterioration of the rocks. While mechanical stresses may play an important role in the interaction of environmental factors, stress effects were excluded from the study. In order to study the effects of environment on coal mine roof rocks, samples were obtained from several coal mines in the western states. The rocks forming the roofs of most of the mines visited were shales of varying composition. These shales were subjected to numerous tests to determine how the rocks changed with time after exposure. In addition, the identity of the minerals present in the shales was determined by x-ray diffraction analysis and by thermal analysis as well as by optical microscopy

Jan 1, 1973

By Horace T. Reno

This information circular surveys the iron are industry of the world. It presents a comprehensive statistical record through 1970 of the U.S. iron ore industry and world trade patterns. The supply position of the United States and the other principal industrial countries of the world are summarized; detailed information is given on iron are production, consumption, imports, exports, mine capacities, substitutes, properties, and uses. There is a generalized discussion of the technology of mining and smelting iron ore, with a selected bibliography on the current state of these arts. The circular contains a summary economic account of world iron are resources, and discussions of the structure of the domestic and principal foreign mining industries, iron are mine employment and labor productivity, research and development, legislation, government programs, and strategic factors.

Jan 1, 1973

By Rudolf E. Greuer

Every mine contains inflammable materials, either in form of the minerals mined or in the form of brought-in supplies. Although great efforts are made to make mines as far as possible fireproof and to prevent ignition sources, the possibility of mine fires, like that of other accidents, will always continue to exist. Detailed statistics are available for coal mines. They show (65,112) that the number of major mine fires in the USA over the last 20 years has remained more or less constant with approximately 50 per year. The same number is reported (26) for the British coal mines. Other countries (147) report about 1 major fire for every 10 million tons of coal production. Conflicting data are published on the number of fatalities caused by fires, presumably because frequently deviating opinions on the cause of death exist. On the average (82,99) 4 miners are killed per year in the US and in the British coal mines. Although this number is much smaller than that for several other causes of fatalities, one must keep in mind that almost every small fire can develop into a large disaster.

Jan 1, 1973

By Lyman C. Hitchcock

The objective of this program was to determine the minimum luminance requirements for underground coal mining work from the working face to the first transfer point. The resulting data encompasses 114 visual tasks from conventional continuous and longwall mining methods representing the salient visual tasks found in the jobs listed. Cutter Operator Roof Bolter Face Drill Operator Airdox Operator Longwall Jackman Shuttle Car Operator Loader Operator Shot Fireman Continuous Miner Operator Longwall Head Conveyor Operator Longwall Tail Conveyor Operator

Jan 1, 1973

By Robert Stefanko

This report, rather than attempting to replace previous annual reports, supplements, and more importantly, coordinates and summarizes the entire effort. Even with such restrictions, the report is voluminous and, therefore, a decision has been made to divide it into two parts. The first volume is basically narrative and includes tabular results and analyses. The second volume is in appendix form giving detailed information. Together, they permit a logical discussion of all aspects of the project (Volume I) without cumbersome distractions but, at the same time, provide all the details to permit others to evaluate and explain the results or develop similar research programs (Volume II). The aim of the original proposal was basically to develop instruments and techniques and then make measurements of suitable power parameters, ground fault currents and ground resistance beds. With such information available, it was possible to develop a meaningful simulator which would permit investigating electrical systems and components on paper without costly trial and error procedures in the third year, a cable splice testing program was added to the project. While there were the usual delays attendant in such original research, these objectives were achieved.

Jan 1, 1973

Electrical trailing cable used to power coal mining machinery is frequently damaged in usage because of tensile strain or crushing effect of mining machines running over the cable. One of the repair problems is finding the exact location of a short or open in this cable so it may be spliced or otherwise repaired. The U.S. Bureau of Mines and FMC corporation signed Contract No. H0 122011 in August, 1971, to develop instrumentation for finding faults in coal mine trailing cable. This report describes performance of several existing instruments as trailing cable fault locators and also construction details and performance records of several cable fault location instruments that FMC designed, built and tested as part of this project.

Jan 1, 1973

U.S. Bureau of Mines contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment", was an investigative effort involving: ? Study of the fire problem on large mobile mining equipment ? Identification of equipment most prone to fire, to serve as a design case example ? Design of an improved fire protection system ? Demonstration of the developed system This effort was performed during the period June 1972 through May 1973, and was conducted in two phases. Phase I, June through November 1972, was devoted to identifying the fire problem and developing and evaluating design criteria. Phase II involved translating the design into hardware and demonstrating its effectiveness during actual fire tests, first on a wooden mockup of a truck, then on an operating truck at a working mine site.

Jan 1, 1973