Search Documents

By Joseph Cervik

Coal is a soft and brittle material. Drilling rates in the Pittsburgh coalbed using a drag bit exceed 3 ft/min at 2,500-pound thrust. However, maintaining the bit on a horizontal trajectory or parallel to bedding planes to attain lengths of 1,000 feet is difficult. This Bureau of Mines report presents a drill string configuration that can be guided through the coalbed. The angle of the borehole is measured periodically and by proper combinations of bit thrust and rotational speed (r/min), bit trajectory can be lifted or dropped to keep the bit in the coalbed. An example of a hole drilled to 2,126 feet is presented to show levels of thrust and rotational speed used to lift or drop the bit, the seemingly unexplainable events that occur, and the strategy used during drilling. Thrust levels during drilling range from 600 to 2,500 pounds. Hydraulic motors powered by a 30-hp, 440-volt motor provide ample power for drilling horizontal holes 2,000 feet long.

Jan 1, 1975

By G. B. Misra

While investigating on the aerodynamic resistance of airways supported with peripheral timber sets, at regular intervals, the following theoretical equations were developed by the author to estimate the resistance coefficient of such airways: [ ] for S < 1, where f is Darcy-Weisbach resistance coefficient of the airway, C is modified drag coefficient of the supporting member, D is equivalent diameter of the bare airway, 8 is ratio of the approach velocity over the sets to the average velocity of the bare airway, A is cross-sectional area of the bare airway, a is projected frontal area of the sets, A., is cross-sectional area of the air stream at the vena contracta inside the set, S is spacing of the sets, f, is resistance coefficient of the bare airway, l is length of aerodynamic influence of sets, p is perimeter of the bare airway, p, is setted portion of the perimeter of the bare airway, pe is unsetted portion of the perimeter of the bare airway, and P shielding factor. The equations were verified experimentally in a model rectangular airway supported with one- (bars), three-, and four-piece sets of square-section timber of three different sizes and were found to hold true. The work has been further extended to one-, three-, and four-piece sets of round timber of 2.6, 3.2, and 3.8 cm diam with the same experimental set up. Tests have been carried out for spacings of 25, 50, 75, 100, 150, and 200 cm over a regime of flow defined by the Reynolds number (with respect to the equivalent diameter of the bare duct) ranging from about 1.5 X 106 to 5 X 106 using the same experimental techniques. The values of f are calculated in the manner indicated in [Ref. 1]. Unlike with square-section timber, the resistance coefficient f of the airway setted with round timber shows a distinct variation with the Reynolds number of flow. This conforms to observations made by Sales and Hinsley.2 In order to have a comparable value of f for all types of sets with all sizes of timber, it was necessary to select the value of f at a fixed Reynolds number of flow. Since f is chiefly a function of the drag coefficient of the sets, the appropriate Reynolds number RE is that with respect to the diameter of timber in the set. Considering the diameters of timber used and the regime of flow over which measurements were made, f was chosen at a value of RE = 20,000 in all cases. The f vs. S curves are maximal in nature and in conformity with theory, the f vs. 1/S curves are straight lines up to a value of S = 1 beyond which they show a distinct flexure. The observed values of 1, the length of aerodynamic influence of sets, agree with the relation 1 = 42 e, developed for square-section timber sets, thus suggesting that the shape of timber has little influence on the length of aerodynamic influence. The value of the modified drag coefficient CD for round timber was calculated in the same way as for square timber in Ref. 1, taking the contraction factor Z = 1.5 for round-edged constrictions. CD has an average value of 0.96 with a standard deviation of 6.08% as compared to the free stream drag coefficient of 1.2 at RE = 20,000 for long cylindrical obstructions The shielding factor [ ] is plotted against S/1 in [Fig. 1]. The curves are more or less independent of the size of timber, but are different for the different types of sets, possibly due to their different degree of symmetry. Values of f calculated by the author&apos;s [Eqs. 1 and 2], using experimental values of CD&apos; and [ ] and taking I = 42 e, are plotted in [Fig. 2] against experimentally measured values of f for different types of sets with different sizes of round timber. The values agree closely with a standard deviation of only 5%, thus establishing the veracity of the theoretical equations developed by the author for round timber as well. A comparison was made between the Xenofontowa4 equations (the only other reasonable relations available for the estimation of the resistance coefficient of supported airways) and the author&apos;s [Eqs. 1 and 2] by comparing in [Fig. 3] the values of the resistance coefficient f computed by the Xenofontowa relations with those experimentally measured by the author. In order to make

Jan 1, 1975

By B. Dimitriades

The Bureau of Mines measured the reactivities of 19 hydrocarbons known to be prominently present in automotive exhaust and ambient air in a smog chamber. Results agreed well with those obtained using two other smog chambers. Reactivity scales were developed for hydrocarbons and aldehydes using the results of this work and those of a previous study. Application of the reactivity scales to automotive exhaust samples gave fair agreement between predicted and observed rate-of-N02-formation values; however, predicted and observed ozone yields were neither in agreement nor did they correlate well. This lack of correlation for ozone yield was attributed to the inappropriateness of (1) the individual component reactivity data, (2) the reactivity classification scheme used, and (3) the linear summation method. In seeking to understand this problem and to develop more appropriate reactivity scales, the data were examined from a reaction mechanism standpoint, and further studies were suggested.

Jan 1, 1975

By Allen M. Newcome

The Ohio valley division of consolidation coal company has incorporated two new aspects within its coal mining concern. A new communication system, thru the cooperation of the c. & p. Telephone company, has been established in each of our mines with its central control in the general office building. In conjunction with this system, a Texas instruments 960 a computer has been incorporated into the system. The purpose for our computer is to provide modernization and improvement to our safety, production and maintenance programs. Thru proper use, the computer will help eliminate inaccuracies and inefficiences that have previously caused inaccurate analysis of problems. Due to federal requirements for more reliable communications in underground mines, Ohio valley division is making a concentrated effort to improve its communication systems. Systems such as the magneto phone and trolley phone have been looked at more critically. It was found that these systems are being used well beyond their limits. With these facts in mind, division personnel started looking for a system that would have these built in advantages: ease of maintenance and installation, increased reliability, low cost, and an inherent ability as a multiple use system.

Jan 1, 1975

After more than 20 years dependence on bituminous coal as a primary fuel for generating electricity, the Pennsylvania Power and Light Company initiated a one-year study on the economics of building an electric generating station using anthracite as a fuel. The study will be completed in December 1976. If the feasibility study so indicates, PP&L will consider installing four 400,000 kilowatt generating units for scheduled commercial operation in 1985. Each unit would consume up to one million tons of anthracite annually. Anthracite generally is more difficult and expensive to extract than bituminous coal, but it has a significantly lower sulfur content than the bituminous coal currently being used by PP&L, thereby eliminating the costs of installing sulfur emission controls at generating stations. Moreover, significant reductions in transportation costs may be realized because the utility&apos;s operating territory is situated in the center of the anthracite region in northeastern Pennsylvania. These advantages may indicate that the use of anthracite is more economical than bituminous coal to PP&L. ASBESTOS -Asbestos production in the U.S. dropped again in 1975 until it was just two-thirds of that in 1973. This was in spite of the very strong demand caused by the Quebec strike. The 7-month strike of the asbestos miners in Thetford Mines, Quebec cut off 55 percent of the normal supply of U.S. consumers. Apparent domestic consumption was less than 75 percent of that in 1974. The wage settlement will probably result in a 20 percent increase in asbestos prices.

Jan 1, 1975

By Wayne D. Gould

Planning for a project does not start with the announcement of the approval for a project. Planning actually begins when the project is only a prospect and it involves the years of experience of many people because their expertise influences the final decisions. In partial anticipation of the Pinto Valley project, as well as a search for improvement in the Copper Cities operation, two projects were undertaken. The first project was to substitute one 26" cyclone for three 20? cyclones in the single stage grinding circuit. The second project was to replace the Hunt air flotation cells with 300 cubic foot mechanical cells. The 300 cubic foot cells were just being introduced, consequently two types of cells were selected for testing. The results from both projects influenced the decisions on equipment for the Pinto Valley project.

Jan 1, 1975

By L. R. Plitt, M. K. Kim

The collecting properties of the fatty acid type collectors for barite were studied using zeta potential measurements, infrared spectroscopy, and Hallimond tube flotation tests. Based upon the experimental results, an adsorption model has been formulated which emphasizes the predominant role of the hydrocarbon chain in collector adsorption.

Jan 1, 1975

The morning session opened at 9:00 a.m. and was presided over by Carlyle F. Gronning, Chairman, Industrial Commission, State of Utah, Salt Lake City, Utah. The first speaker was John A. Fagnant, Vice President-Sales, Kemmerer Coal Company, Frontier, Wyoming. Subject - "Open Pit Coal Mining, Western States." Mr. Fagnant is a graduate of Colorado School of Mines, 1937 Degree, Metalurgical Engineer His career in the mineral industry began at the Arthur Mill of Kennecott Copper Company. For nine years he was with Allis Chalmer Company in Milwaukee, Wisconsin as a Sales Engineer in the Mining Machinery Division. Following five years in private business, he joined The Kemmerer Coal Company as a special projects engineer specializing in coal carbonization. He was assigned the job of Sales Manager in 1968 and promoted to Vice President of Sales in 1970. Member of A.I.M.M.E.

Jan 1, 1975

By E. C. Winegartner

In producing and selling coal, the coal company is faced with many different parameters by which the quality of its product is evaluated. One type, which we choose to call the economic parameters, includes moisture, ash, sulfur, and Btu&apos;s. These are reasonably well understood by both the coal supplier and the customer, and the dollar values can be placed on them. This is the group of parameters of primary interest to most purchasing agents buying coal. A second group of parameters governs how the coal will behave in the boiler itself and is of primary concern to the engineers designing the boiler and to the men who must operate and maintain it. Since we have not yet learned to put dollar values on these parameters, they generally show up in coal contracts simply as cutoff points, the purchaser simply saying that he will not accept coal outside of certain limits.

Jan 1, 1975

By K. A. Natarajan, I. Iwasaki

The influence of dissolved oxygen and the Pt - Pt-O reaction on the measurement of redox potentials in solutions containing ferrous-ferric couple was examined. Current-potential curves were used to illustrate the shift in measured potentials toward the oxygen potential in oxygenated and deoxygenated systems at low concentrations of ferrous and ferric ions. The ranges of concentrations of the ferrous-ferric couple, in which the interference from oxygen and the platinum-oxygen reactions becomes significant, are illustrated through the mixed potential mechanism.

Jan 1, 1975

By C. A. Wilson

The Bureau of Mines started a continuing program to investigate and evaluate analytical techniques to assist governmental agencies to select simple, rapid, reliable methods for crude oil spill identification. Six crude oil samples were analyzed to evaluate gas-liquid chromatography, atomic absorption spectrophotometry, infrared spectoscopy, sulfur and nitrogren determinations, mass spectrometry, nuclear magnetic resonance spectroscopy, and ultraviolet spectrophotometry. Samples were studied from the following selected fields: El Morgan, Egypt; Duri, Indonesia; Minagish, Kuwait; Bachaquero, Venezuela; Gach Saran, Iran; and Prudhoe Bay, Alaska. These samples were chosen to represent high-production fields that are likely to be involved in oceanic transport. Over 50 years of Bureau of Mines analytical research on petroleum served as the basis for evaluation of the experimental results to determine which of the methods are effective techniques to identify crude oil spills. Gas-liquid chromatographic analysis, atomic absorption spectrophotometric analysis, and sulfur-nitrogen determinations are recommended as the most useful of the techniques investigated.

Jan 1, 1975

The mineral chromate is the sole current source of commercial chromium Chromite varies compositionally within limits permitted by the formula ((Mg,Fe,Zn,Mn)(A1,Cr)2O4) No chromate has been mined in the United States since 1961 In the past, almost all the chromate mined in the United States came from Alaska, California, Maryland, Montana, Oregon, and Pennsylvania, with about one-half of all production coming from Montana Primary chromate deposits occur only in certain kinds of ultramafic or closely related anorthositic rocks The two major types are stratiform (layered) and pod-shaped The Stillwater Complex of Montana is the largest known United States resource It is a stratiform deposit where several exposed zones of high-iron chromiferous material extend in length Since there is no commercial chromate mining in the United States, there are no environmental problems related to underground mining

Jan 1, 1975

By Robert G. Bottge

Hard rock mining has grown in importance in the Yukon Territory during the last 10 years while Alaskan hard rock mining has declined. One asbestos deposit in Alaska is dormant, but an asbestos deposit 55 miles to the east in the Yukon Territory is being mined by the Clinton Mine Div., Cassiar Asbestos Corp., Ltd. In this Bureau of Mines report, the economics of mining in the two locations were derived using the Clinton mine as a model. Both deposits were assumed to be of equal size and mined by similar methods. Conventional open pit mining and processing methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The estimated cost for the mine, mill, and support facilities in Alaska was about 30 percent more expensive than that in the Yukon Territory. The higher labor rates in Alaska were the primary contributor to the higher construction costs; freight rates added only slightly to the total costs. Approximately two-thirds of the additional annual costs of operating in Alaska were for wages and fringe benefits. The price required for the Alaskan asbestos fiber was $356.65 per ton compared with $287.44 for Yukon fiber, plus or minus 20 percent. A 12 percent discounted cash flow rate of return, 100 percent equity financing, and a rapid writeoff of assets were assumed.

Jan 1, 1975

By Charles W. Trettel

Confined explosives upon detonation produce a chemical reaction generating expanding gases that result in fragmentation of matrix a chemical to mechanical transition. A 100% energy conversion during transition is difficult, if not impossible, to achieve. There are numerous variables that affect energy transition. Although fragmentation is the most often used criteria to determine shot efficiency, the escaping energy profile provides additional data as to the efficiency of a blast. Escaping energy can also have deleterious effects in the form of ground motion.

Jan 1, 1975

By Robert B. Crookston

Oil from shale has been produced in foreign countries for more than a hundred years; however, except for short-lived, small operations, no commercial quantity of oil shale has yet been produced in the United States. Efforts to develop a viable oil shale process have been underway domestically for many years. At the present time, with the need for energy so urgently upon us, almost a dozen development ventures are underway or planned in Colorado and Utah. Of these several ventures, only Colony Development Operation has completed the development, testing and design of a ready-to-go 50,000 barrel per day com¬mercial project. Colony is a joint venture of the Atlantic Richfield Company, Ashland Oil Company, Shell Oil Company and The Oil Shale Corporation, more commonly known as TOSCO. TOSCO is the exclusive licensor of the TOSCO II retorting process and other oil shale technology, which includes mining, crushing and spent shale disposal techniques. This paper will deal, however, with only the materials handling aspects of the commercial oil shale operation. Oil shale handling for this infant industry is unique in that an understanding of the physical characteristics of the ore and the demands on material handling to the plant must he understood. Colony Development has completed ten years in the research and development of techniques and processes for mining, crushing and retorting raw oil shale and the disposal of spent or processed shale. A great deal has been learned about oil shale, in many cases confirming our intuitive analyses and the work of others, but more specifically we have brought it all together to a point where equipment performance and the specifications have been established and a design for the first commercial plant is now mature.

Jan 1, 1975

By W. T. Westbrook

This Bureau of Mines report contains methods for analyzing iron are for total iron, ferrous iron, metallic iron, silica, manganese, aluminum, calcium, magnesium, phosphorus, titanium, carbon, sulfur, moisture loss, and ignition loss by wet chemical methods. Some are modifications of standard umpire methods; others have been developed by the Bureau of Mines to provide a com-bination of speed and accuracy. They are suitable for a high volume of samples and/or control situations, and for situations in which instrumental results must be verified. These methods have been used to analyze taconites, native ores, some foreign ores, and metallurgical products.

Jan 1, 1975

By Trudinger JP

Mt. Newman Mining Company Pty. Ltd.3 oper ates the Mt. Whaleback iron ore mine in the Ham- ersley Iron Ore Province of Western Australia. The present rate of production of high grade hematite iron ore is 33 million tonnes per year. Mining is by open cut quarrying,with 15m high benches. The present quarry operations will be extended to a large oval pit to win over 1400 million tonnes of iron ore. The pit slopes will extend up to 500m in depth and the perimet- er of the slopes will exceed 15km. Sixty per- cent of the ore is below the water table, which presently lies 45m below the general plain level Dames & Moore, rock mechanics consultants designed the pit slopes during early mine devel- opment to ensure an economic and safe operation.

Jan 1, 1975

By S. L. Crouch

The application of a simple, two-dimensional computer technique for evaluating rock burst potential in cut-and-fill stopes was investigated. The principal purpose of the study was to compare the effectiveness of high-modulus fill and destressing as aids in the control of rock bursts. Two conclusions that are probably of general applicability are drawn. First, high-modulus fill is ineffective as a means of increasing the mine stiffness and acts to control rock bursts only if it supports enough load to reduce substantially the stresses on the unmined vein material. Second, destressing is most effective if it is performed when the vein material is near the point of failure.

Jan 1, 1975

By Donald I. Kurth

The Bureau of Mines conducted experimental work on comminuting coal. The size distributions of coarse fragments and fine particles were obtained under different modes of energy application--drop, impact crushing, wedge impact, compression, and shear tests. Four levels of energy application were used in the impact crushing and wedge impact tests. Airborne dust and respirable air-borne dust distributions were obtained for the impact crushing and wedge impact tests. Analyses of nonairborne dust and coarse fragment-fine particle distributions were carried out on impact, wedge, compression, and shear tests. The experimental size data on nonairborne dust were fitted to normal, log-normal, power law, Weibull, log-Weibull, and exponential distribution functions. Both the nonairborne dust and the coarse fragment-fine particle size distributions are best described by Weibull distributions. For the impact crushing tests, mean product size was found to be inversely related to specific crushing energy. The particle counts in a given size range of airborne and nonairborne dust were found to increase with increased input energy and specific crushing energy. However, in another sense the particle distributions were independent of energy level; that is, the percent-ages in a given size range were approximately constant regardless of energy level. Respirable airborne dust was related to respirable-size nonairborne dust by a power law.

Jan 1, 1975

By H. Billmayer

This report covers the period from June 17, 1974 to February 20, 1975, and describes the work performed in compliance with the requirements of Contract No. H0346102 and Modification No. 1 thereto. The purpose of the contract was to design protective canopies for an Elkhorn Scoop, a Lee Norse Miner, a Wilcox Miner and a Wilcox Bolter; to construct mockups of the canopies; and to obtain machine operator evaluations of the canopy designs by assessing the mockups while installed on their machines in the mines. The overall program objective was to achieve protective canopy designs for the four machines which would be acceptable to the operators.

Jan 1, 1975