Search Documents

By Ta M. Li

In Gila County, Ariz., the Jaquays Mining Co. still finds the mining of asbestos a worthwhile and economical venture. At a time when domestic productive capacity is being reduced because of rapidly rising costs and tough environmental dust standards, this firm has dramatically brought its mine and mill operation into full productive capacity and compliance with both Federal and State regulations. Jaquay's Mining Corp. owns four underground mines in the Tonto National Forest, located approximately 32 miles north of the Globe-Miami District in Arizona. Only one mine, the El Dorado, is presently active. It mines an estimated 45,000 tpy of ore and waste. From this figure about 3000 tpy of fiber (No. one crude to Grade 4T) and fiberized shorts (No, seven) are recovered at the firm's mill, located in Globe, Ariz. Based on current ore reserves, the El Dorado mine has an estimated life between 15 to 17 years, assuming current mining rates and stable market conditions.

Jan 3, 1975

By Frank R. Milliken

Before the rather sudden economic downturn in recent months, shortages of materials were painfully felt throughout the US. The current recession has provided a temporary relief here and there-but energy fuels and a number of staples such as sugar are still in short supply. This is an unsolved and fundamental problem that will haunt us again as the economy turns up. There is an awareness that the nation faces a widening supply gap in many of its most basic materials-from asbestos to tungsten-as evidenced by recent studies and government reports, and by the Secretary of the Interior's annual warnings about the mounting seriousness of the problem.

Jan 3, 1975

By Ta M. Li

A record 340 senior students with majors in mining and mineral engineering from 21 shcools in the US may be expected to enter a manpower-hungry mineral industry in 1975. While starting salaries may have been the deciding factor in job selection in the past, 1975 graduates will find salaries almost the same in most mining sectors. Meanwhile, the survival prospects of various mineral engineering schools had the usual ups and downs in 1974, but tightening state budgets could still take a toll in reducing the number of schools offering mineral engineering degrees. Two such schools on the endangered list include Montana College of Mineral Science in Butte, Mont., and the College of Mines, University of Idaho, in Moscow, Idaho.

Jan 3, 1975

By D. Clement

A comparison between hydraulic and pneumatic rockdrills by D. CLEMENT The regulation of compressed-air reticulation systems is very poor compared with that of electrical systems; this means that electrohydraulic rockdrill systems offer greater flexibility, additional power being readily available at the working face. Hydrometallurgy A new journal devoted to all aspects of the aqueous processing of metals is scheduled to appear this year. Entitled Hydrometallurgy, the journal will be published in quarterly issues, one volume per year. Mineral dressing Contributions are invited for the Symposium on Recent Progress in Mineral Dressing in South Africa, which is to be arranged jointly by the South African Institute of Mining and Metallurgy and the National Institute for Metallurgy. Mineraalbereiding Bydraes word verlang tot die Simposium oor Onlangse Vordering met Mineraalbereiding in Suid-Afrika wat gesamentlik deur die Suid- Afrikaanse Instituut vir Mynbou en Metallurgie en die Nasionale Instituut vir Metallurgie gereel gaan word. Rock mechanics The Sixteenth Symposium on Rock Mechanics is to be held at the University of Minnesota from 22nd to 24th September, 1975. The Symposium is the official Symposium for 1975 of the International Society for Rock Mechanics (I.S.R.M.), and the Council for I.S.R.M., consisting of members from 25 countries, will meet during the Symposium. Powder metallurgy The annual meeting on powder metallurgy organized by The Metals Society is this year to be held at the Stratford Hilton Hotel, Stratford-upon-Avon (the notification did not include the date of the meeting). Vacation School The South African Institute of Mining and Metallurgy has great pleasure in announcing its intention of holding a vacation school on the topic of electric-furnace melting. NIM reports Report no. 1681 The determination of sulphur and phosphorus in chromite. Report no. 1687 The viscosities and electrical conductivities of slags associated with the production of high-carbon ferromanganese alloys.

Jan 3, 1975

By H. M. Friede

Notes on the composition of pre- European copper and copper-alloy artefacts from the Transvaal by H. M. Friede. Ph.D. (Visitor) Seven copper artefacts (five ingots and two ornaments) found at prehistoric sites in the Transvaal were submitted to analysis. All the artefacts showed a high copper content and a relatively Iow level of impurities. A little-known ingot type from the Limpopo Valley ('nail' ingot) is described, and its analysis is given. The analysis of two copper ornaments that come from sites dated to the 5th Century AD. and the 11th Century AD. showed the constancy of the composition of copper articles over long periods. The well-known 'Blaauwberg Ingot' was re-analysed, and the results showed that this ingot cannot be regarded as a true bronze. Analytical values for the composition of three brass artefacts from Bambandyanalo (Mapungubwe), Northern Transvaal, are given. Some aspects of pre-European bronze manufacture and brass smelting, and of early metal trade from the East Coast into the interior of South Africa, are discussed.

Jan 2, 1975

Although the mining industry faced ever-increasing risks and uncertainties in 1974, it nevertheless pushed ahead with considerable rapidity in exploring and developing new orebodies-while expanding and improving the technologies of mining and exploration. Prepared by the SME Mining and Exploration Division, this section of the annual review covers the pertinent worldwide developments in the fields of geochemistry, geology, geological engineering, open pit mining, underground mining, rock mechanics, operations research, and solution mining.

Jan 2, 1975

Prediction of the performance of explosives In bench mining by C. M. LOWNDS, B.Se. Hons (Rhodes), Ph.D (Cape) (Visitor) Some of the problems encountered in the calculation of the relative weight strength of explosives are discussed, and a realistic model of the behaviour of explosion products in a borehole is proposed. The heat flow from condensed to gaseous products is calculated as a function of time, and the relationship between the pressure and the volume of the product gases is found by a consideration of the compression of the rock between radial cracks. Work done on the burden is assumed to cease when the cracks first appear at the face. Reasonable values of burden and crack velocities are obtained from the model. Calculations of the relative weight strengths of aluminized mixtures of ammonium nitrate and fuel oil show that the increased density resulting from the addition of aluminium is the main advantage to be gained.

Jan 2, 1975

In introducing last year's Industrial Minerals Review, Stan Lefond accurately predicted that the 1974- 75 period would be quite difficult and frustrating. Although 1974 demand and prices for most industrial minerals were exceptionally strong, operating costs also rose rapidly-while shortages of supplies and equipment, symptomatic of an overheated economy, occurred from coast to coast. Thus, at the end of 1974 recessionary forces were accelerating-and the minerals industry will soon be facing falling demand as a consequence of sharp declines in auto production, housing, appliances, and other consumer goods. Moreover, when sales weaken, the high-volume, low-prices industrial minerals will incur sharply increased unit costs. To maintain adequate profit margins under these conditions will require cautious and perceptive management.

Jan 2, 1975

Energy conservation has been the keyword in many plant expansions. Far many years, most of the phosphate industry has been dry grinding their phosphate rock. Agrico Chemical in Florida has recently been evaluating the wet grinding of phosphate rock, a process which eliminates a pre-dry stage for mill feed while allowing higher through- puts. This same company also plans to open a new phosphate facility in Louisiana that will use wet grinding in both ball mills. The Eveleth Expansion Co.'s Fairlane concentrator will have the largest rod and ball mills in the US mining industry. The plant will consist of three lines, each with one rod mill and one ball mill, and will process 464 ltph. The rod mills will be 15 x 20% ft, drawing 2035 hp. The ball mills will be 17 x 41½ ft, drawing 6900 hp and driven by dual 3000- hp motors. The plant is scheduled for startup in the fall of 1976.

Jan 2, 1975

The North American Coal Corp. Increasing demand for coal, stimulated by the national energy shortage, and complicating and often conflicting, demands by government and ecology groups for better land reclamation methods continued to propel advances in surface mining technology during 1974. To meet current demands for coal (estimated at more than 700 million t for 1975 and 1.5 billion t in 19851, equipment manufacturers and coal operators concentrated on increasing the productivity of all surface mining equipment. The trend towards larger equipment, particularly in overburden removal, loading, and haulage machinery, prevailed during the year, notwithstanding the perennial debate over the economics and practicality of using large, inflexible equipment. Increasingly, the industry called on computers to monitor productivity and help design more efficient production systems

Jan 2, 1975

By Hon-Chung Ko

This Bureau of Mines report provides the enthalpies of formation of cupric bromide and cuprous bromide as determined by hydrochloric and hydro-bromic acid solution calorimetry. At 298.15 K, the values are -33.10 ± 0.4 kcal/mole for CuBr2, and -25.24 ± 0.25 kcal/mole for CuBr.

Jan 1, 1975

By Kenneth A. Gutschick, Robert S. Boynton

Lime has become a general and loosely used term to denote almost any kind of calcareous material or finely divided form of limestone or dolomite, as well as burned forms of lime. However, according to Webster, lime is only calcined limestone (known as quicklime, unslaked lime, or calcium oxide). It also embraces the secondary product of quicklime, i.e., hydrated lime or slaked lime (calcium hydroxide). There are two basic types of limestone used for lime manufacture-high calcium and high magnesium (dolomitic). The dolomitic quicklimes and hydrated limes correspond to their "high calcium" counterparts. The only difference is that the dolomitic types are a combination of the elements calcium and magnesium, in varying percents, whereas high calicum limes contain less than 5% MgO down to 1/2%. In either case a pure form of limestone of at least 97% combined carbonate content is needed to make salable lime, barring a few exceptions. The calcination of both types is diagrammed chemically as follows: [ ] In the foregoing reversible reactions the limestone is burned (calcined) in lime kilns, with the carbon dioxide content of the stone expelled as a gas. The weight loss during calcination of pure high calcium limestone is 44%; with equimolecular dolomitic limestone, the weight loss is 48%. Since lime has a strong affinity for CO_, particularly if moisture is present, it will readily revert to its original carbonate form. This occurs when quicklime "air-slakes" and adsorbs CO.. from the air. Thus, quicklime is perishable and should be stored in dry, water-tight areas. Depending upon the type of kiln used and the physical structure of the stone, the size of the quicklime may range from sandlike granules to 8 in. lumps. However, pebble sizes ranging from 1/4 in. to 2 in. are the most common. Screened quicklime fines are also com¬pressed (pelletized) into 1 in. pellets. For some purposes ground or pulverized forms of quicklime are used, ranging from No. 10 mesh to dust. Generally a pebble of quicklime is about the same size as the pebble of limestone before calcination (perhaps shrinking slightly). A more stable form of lime is hydrated lime. This is obtained by adding water to quicklime, slaking it into a dry, fine, subsieve size white powder. Because its affinity for moisture has been satisfied, it is not vulnerable to further moisture like quicklime. However, it has the same strong affinity for CO_. The following reversible chemical reactions illustrate how hydrated lime when heated (or dehydrated) can revert to the original oxide form:

Jan 1, 1975

By David E. Hyatt

The chemical attributes of cyanides have long been exploited in ore pro- cessing schemes for the recovery of copper, molybdenum, gold, silver, and other metal values. Blast furnacing operations are significant unintentional producers of cyanides which find their way into process waters. Many of the more than 20,000 electroplating facilities in the United States utilize cyanide plating baths and generate cyanide containing wastes. As social, political, and economic pressures for water quality attainment, maintenance, and preservation grow, the requirements for the development of treatment technology to control cyanide levels in wastewater become increasingly apparent. Just as the chemistry of the cyanide ion 1s an integral part of its industrial applicability, so must this chemistry be a fundamental part of any decomposition or removal technology used to control its level in effluent or recycled waters. The complexity of this chemistry is substantial and it cannot be considered in a superficial or cursory manner if control system design is to be both efficient and reliable.

Jan 1, 1975

By P. R. Tisot

The structural response of propped oil shale fractures was determined for each of two different grades of Green River oil shales (38.0 and 29.0 gpt) as they were heated in an inert atmosphere from ambient to subretorting temperatures (below those required for rapid pyrolysis of the organic matter). Small oil shale cores were propped apart by 3-mm glass beads to simulate a small cross section of a propped oil shale fracture between an injection and a producing well. These specimens were then heated at a uniform bate up to 800° F in a specially designed test cell under stress levels from 100 to 1,000 psi in biaxial and in triaxial confinement. Under the conditions of heat and compressive stress utilized in this study, all of the propped fractures in the two oil shales underwent structural deformation ranging from partial to complete collapse, as evidenced by proppant embedment. Structural collapse of induced fractures would in turn result in serious impairment or complete loss of the fracture flow capacities of the specimens. Results from this Bureau of Mines study indicate that underground retorting of Green River oil shale may be seriously impaired by loss of permeability when utilizing propped fractures in oil shales assaying more than 28 gpt.

Jan 1, 1975

President-elect Bob Wilson opened the business meeting at 9:30 a.m. He called on Shirl C. McArthur to report on the financial statement of the treasurer. He read the data and asked for its approval. A motion was made, seconded and approved. The Resolutions Committee was called upon to make its report. The following resolutions were submitted: (1) RESOLVED: WHEREAS, in the year since the last convention of the Rocky Mountain Coal Mining Institute, the Institute and the coal mining industry have suffered the loss through death of the services of: J. S. Besser Harry Brophy Walter E. Burleson A. F. Geiger Wilbur J. Gunther Albert W'. Holmes Harold Levene Larry Littlejohn David H. Michael Carmal Patton Charles M. Schloss Ira R. SigMan

Jan 1, 1975

The Savage River Mines concentrator and pipeline has operated for seven years. During this time some problems of general interest have been overcome, particularly in the area of autogenous grinding in large mills and in pump- ing solids over long distances. The plant flow sheet and equipment at Savage River and the control techniques are. described. Ore type has varied widely over the per- iod of plant operation. Techniques developed to minimise the effect of variations on through- put are discussed'. The main technique is the controlled rejection or addition of grinding Media.

Jan 1, 1975

By Palmer DJ, Bain JH, Pullen JB

Over the last ten years at Risdon, zinc production capacity has almost doubled. This has resulted in modifications, many of which have affected zinc deposition operating conditions in the cells. Some of these changes appeared to have affected average current efficiency to such an extent that a special investigation was initiated, using multiple regression analysis to assess historic cell unit operating para- meters. The study highlighted the importance of certain parameters in maintaining maximum current efficiency for zinc deposition from !Risdon purified solutions under conditions of !changing current density, acidity and zinc con- centrations. Maximum current efficiency was obtained only within a zinc to acid ratio in cell electrolyte of 0.45 - 0.55 and a residual zinc concentration greater than 48 g.1-1, irrespective of actual zinc concentration or The investigation also established: ieters giving minimum power consumption at termined current density; the effect of ntration changes in common impurities on nt efficiency; the existence of high s of some impurities in solids precipit- in the cells and pure solution tanks.

Jan 1, 1975

By Robert M. Cox

A roof bolting theory and structural model are presented which explain the success of most roof bolting installations as the creation of a competent roof bolt reinforced rock arch within the immediate roof rock overlying an underground opening. Likewise, the failure of some bolted mine roofs can be explained as a failure to create a structually competent rock arch by roof bolting.

Jan 1, 1975

By L. E. Dalverny

This Bureau of Mines report describes the deployment, 5-month operation, and lessons gained from a continuous gas monitoring system using sampling-tube bundles at an underground mine fire in West Virginia. Research information gained indicates the utility of relating certain gas concentration ratios to events during fire development, mine reventilation, and mine recovery. In addition to monitoring the quality of remote fly ash seals, the system provided timely warning of dangerous gas concentrations which developed during surface and underground recovery activities. An evaluation of system components is supplemented by recommendations for improvements.

Jan 1, 1975

By A. S. Kastrinos

There are many concepts of preventative maintenance. The basic objective of all maintenance organization, however, is the efficient (accomplishment and control of all) inspection, repair, overhaul, material and preventative maintenance functions necessary to maintain facilities and equipment in a condition that will meet operating requirements at a level consistent with low costs and high availability. To formulate a preventative maintenance program requires sound judgment and the ability to apply in a practical manner a system that meets Plant operation requirements, based upon organization, experience, conditions, design and historical data. A maintenance program must be divided into to categories consisting of: 1. Scheduled tasks to be accomplished at planned intervals. The objective of these tasks is to maintain reliability and prevent as much as possible abnormal failures. 2. Non-scheduled tasks that result from periodic reports and which can be scheduled to fit in conveniently with other routine work. The non-scheduled work items may include long-range preparation for lenghty shutdowns requiring Engineering and Shop services.

Jan 1, 1975