Search Documents

By Theodore Christos

The Bureau of Mines sponsored an investigation of the thermal oxidative degradation characteristics of selected ingredients employed in the formulation and manufacture of conveyor belts. This work was done to supplement similar studies of samples from finished conveyor belts and thus provide basic data for correlation of the potential toxic behavior of a finished belt with that of the individual ingredients. This report covers the study of (1) basic polymers (styrene-butadiene, neoprene), (2) reinforcing fibers (Nylon 6,6, Dacron, viscose rayon), (3) flame-retardant plasticizers (tritolyl phosphate-isomeric mixture, tri-p-tolyl phosphate, tributyl phosphate, tris (dichloropropyl) phosphate), (4) plasticizers (diphenylphtha1ate, di-(2-ethylhexyl) sebacate), and (5) a vulcanization accelerator (2-mercaptobenzothiazole).

Jan 1, 1977

By R. Agarwal

The in-situ stress field was determined, using the overcoring technique, at two underground sites at the Pea Ridge Mine, Sullivan, Missouri. At one of the sites in magnetite, the three dimensional stress field showed the largest principal stress to be compressive (-4564 psi), nearly horizontal and closely parallel to the strike of the orebody. The smallest principal stress was also compressive (-2047 psi) and nearly vertical. Considerable difficulty was experienced in drilling porphyry rock at the second test site in the host rock. Only one hole was drilled at this site. The secondary principal stresses obtained in the porphyry are -9464 and -4945 psi, respectively. The-test site in magnetite is located at a depth of 2505 feet whereas the site in porphyry rock is at 2475 feet. The vertical stresses: due to overburden loading at these sites are -3590 and -2782 psi, respectively. Field determined values of the vertical stress are -2207 and -5098 psi, respectively. The variance; between the two sets of values is most likely attributable to the orebody formation and the differences in the modulii of the host rock and the orebody.

Jan 1, 1977

By Tomlinson R. C

The paper will briefly describe planning in the National Coal Board (NCB) and the contribution that operational research makes to it. It will then give details of some of the models in use and will finally consider critically the problems of looking ahead to the next century.

Jan 1, 1977

By A. E. Lindquist

This Bureau of Mines publication identifies areas having sufficient coal reserves to support synthetic natural gas (SNG) development and summarizes those areas having the highest potential. Capital requirements, mining and coal cost factors, water availability, and coal-quality data pertinent to SNG production are presented. Evaluation of individual coal reserve blocks was based upon coal and water requirements of the Bureau of Mines Synthane coal gasification process.

Jan 1, 1977

By R. N. Bhattacharyya

In recent years, increased attention is being paid to the application of oil-agglomeration technique for (a) improved recovery of low- ash clean coal, (b) effective beneficiation of low-grade coking coals and (c) removal of pyrite sulphur from high-sulphur coals. In this technique, which has been proved to be more effective than convention- al froth-flotation, advantage is taken of the oleo-philic nature of finely ground coal to separate it under controlled conditions from the associated minerals which are hydrophilic in nature. Unlike froth- flotation, no aeration is needed in the process and the concentrates which are obtained in the form of agglomerates or micro-pellets have easier dewatering characteristics. Optimization of operating variables in treating individual raw feed is a pre-requisite for the successful application of this process. A 10 gram batch unit was employed in the present test series. This paper presents - results from these investigations on such operating variables as (i) size of coal, (ii) amount of oil used, (iii) time of stirring, (iv) rate of stirring, (v) solid content in slurry and (vi) effect of conditioning.

Jan 1, 1977

By Thomas O. Glover

History of Underground Coal Mining in Illinois The production of coal in Illinois using underground mining methods, commenced early in the 1800's; however, the first shaft entrance was not sunk until 1842. The shafts range in depth from 16 feet (4.9 m) in Peoria County to 1,001 feet (306 m) in Christian County. The earlier mines were smell, private operations that worked outcrops and shallow seams at less than 100 feet (30.5 m) in depth. By 1975, there were reported 4,076 abandoned underground coal mines in 70 Illinois counties (Nawrot, 1977). There were many more mines; however, only 4,076 underground mines have been documented. Small mining operations characterize the majority of the underground mines. There have been no significant multiple seam operations in Illinois. The most extensively mined seams were the number two, five, and six seams. Number two seam was worked in the early 1900's by 252 mines in the longwall mining region of northern Illinois (Nawrot, 1977). Available records for 2,054 abandoned mines identify 1,043 as shaft nines, 700 as slope mines, and 311 as drift mines. Some operators began reporting annually to the State Department of Labor in 1879 and by 1882 all mine operators were reporting. Annual reporting still continues to date. The information is compiled by the State Department of Panes and Minerals in their "Annual Coal Report." By the end of 1974 there were 800,000 acres (323,756 hectares) of abandoned underground coal mine workings (Smith-Stall, 1975)2 Copies of abandoned underground coal mine maps may be inspected by interested parties in the State Department of fines and Minerals office in Springfield, Illinois, or at the office of any county recorder for mines within their county. Copies of active underground coal mine maps may be inspected at a State mine rescue station near the mine site or at the county recorder's in the county in which the mine is located. Copies of active underground coal nine naps shall be open to the examination of all interested persons, but such examination shall be made only in the presence of the State mane inspector or the recorder. At the present time, the Department of Mines and Minerals has 1,746 maps of abandoned underground coal mines in its possession. These maps cover the majority of

Jan 1, 1977

By John S. Carman

Our industry is in trouble. Real trouble. It has never been an easy, secure business. But to-day it is engulfed in revolutionary currents. No longer can there be reliance upon the checks and balances of market forces. Supply and demand largely dictated the economics of business enterprise in simpler days. To-day politics, in particular nationalism become increasingly dominant. And as governments expand and put out tentacles of interference in the direction of the mining industry, far too little understanding is evidenced as to how that industry works. Then there is something which is relatively new -stagflation. As the prices of minerals falls, the capital investment required for new extractive facilities soars at rates which far outdistance those which are cited by governments to indicate the magnitude of inflation. To illustrate; 1) In 1971 it was calculated that $355 million would be required to bring the Cuajone property in Peru into production. Five years later that stage was reached at a cost of $680 million. 2) With the Caridad mine in Mexico, estimated capital investment doubled between 1971 and 1976. 3) The requirements calculated for Cerro Colorado in Panama have risen in two years from $560 to $800. 4) The budget of $240 million for Sar Chesmeh in Iran in 1971 had become $500 million by 1976.

Jan 1, 1977

By G. S. Barry

INVESTIGATIONS to date have shown that, should there be the need or the appropriate economic stimulus, Canada's mineral resources are sufficiently extensive to allow considerable expansion of its non-fuel mineral industry, during the remaining part of this century and possibly beyond (1, 2). The availability of sufficient capital will be one of the critical factors which will determine whether this potential will be fulfilled. The following analysis centers on the capital requirements of the Canadian non-fuel mineral industry under one set of basic assumptions of capacity growth, cost of new and replacement capacity, rates of depletion and depreciation of mines and plant, and the cost of exploration and infrastructure. Mindful of the fact that exploration and development will not thrive in Canada unless a very positive approach is taken, the writers make no apologies for being "optimistic" about long-term production prospects. Furthermore, in the event that world demand does escalate as anticipated and the forecast realistically attainable levels of Canadian production are not reached, then Canada will not have reaped the full range of economic benefits available, and opportunities will have been lost. Projections for Canadian production between 1976 and 2000 are essentially based on the forecast published in the 1974 paper, "Towards a Mineral Policy for Canada - Opportunities for Choice (3), with some updating on the basis of recent developments.

Jan 1, 1977

By R. K. Koch

The Bureau of Mines developed a zircon sand molding process for static casting of small titanium or zirconium shapes. Castings with unfinished weights up to 3.5 kg (7.7 lb) were produced in an inductoslag furnace and castings up to 7 kg (15.4 lb) were poured in a consumable electrode skull-casting furnace. Molds and cores were made by ram-molding, foundry-grade zircon sand (AFS gfn 93 to 95) bonded by grade D waterglass and tempered with water. Molds and cores were cured either at 250° C (482° F) or 900° C (1,652° F). Castings from the higher temperature molds broke cleanly from the sand while the lower temperature molds produced castings that had to be cleaned by sand-blasting. However, low-temperature cured molds and cores have a number of advantages as follows: (1) A faster, less energy-consuming curing cycle is used; (2) expended cores are water soluble which greatly facilitates core removal; and (3) enough of the binder in crushed expended molds is reactivated by temper water so that the molding mix can be reused five times without any fresh binder additions and up to twenty times without exceeding a total cumulative binder addition of 52 ml/kg dry sand. Crushed used molds that had been cured at 900° C had no detectable binding strength when mixed only with temper water. A large number of oxide and silicate mold washes were studied for improved casting integrity. The most effective wash found for zirconium or titanium casting was monoclinic zirconia (325 mesh).

Jan 1, 1977

By Benjamin F. Merembeck

A mutispectral scanner (MSS) obtains remotely sensed data of the earth's surface in vector form, one vector element for each spectral sensing band of the MSS. Data generated by either airborne or orbiting MSS systems are organized in a lattice of scan lines and elements within scan lines. Each element, called a pixel, is represented by an observational vector and corresponds to a relatively small specific area on the ground. The total observations for a sensed scene frequently are in the millions and are composed of a number of populations, each representing a different land form category. Based on samples from the populations, the mean vectors, or spectral signatures, and the covariance matrices for the categories may be estimated. From these, an among category covariance matrix and a combined within category covariance matrix can be found. The total among category variance is the trace of the among category covariance matrix. Canonical analysis finds a linear transformation matrix such that the first transform variable accounts for the maximum possible part of the total among category variance. Similarly, the second transform variable, orthogonal to the first, accounts for the maximum possible part of the remainder of the total variance, and so on. Such transformation often results in over 95 percent of the total variance accounted for in the first three canonical variables, even though the initial number of spectral bands exceeded twenty. Transformation of bulk data into three canonical variates allows color map products to be developed by assigning each variable to a different basic color. Such color products are believed to be more useful for photo-interpretation than color products resulting from any combinations of three of the initial spectral bands.

Jan 1, 1977

By Tayler H. Bingham

Personal consumption expenditures represent roughly two-thirds of total of GNP. While these expenditures directly account for only a small portion of total natural resource consumption, they account for a significant proportion indirectly. The reason is that all economic activity can be shown to be interrelated and that the intermediate production sectors, which are the primary users of natural resources, represent the interindustry transactions necessary to produce all final goods, including consumer goods. This paper provides a discussion of the methodology and quantitative estimates in physical units of the interrelationships between 15 major nonenergy resources and 6 energy resources and 477 personal consumption expenditure items.

Jan 1, 1977

By A. L. Hornbaker

Management of mineral resources through land-use planning procedures is not a new concept, particularly at the local level of government. Colorado may well be one of the first states, however, to vigorously attempt to evaluate on both the state-wide and regional basis, mineral resource potential and to make certain that potential for mineral resources is included as one of the primary factors considered in the local land-use decision-making process. Less than a decade ago the only consideration given to mineral resource extraction, particularly aggregate resources, was whether or not they could be produced at the particular time they were needed. This attitude has now shifted to the other extreme, not only in Colorado, but other states as well, so that other interests, especially housing projects, mountain subdivisions, recreational and wilderness areas are gaining prime consideration in land-use decisions. Ideally, in a more acceptable median position, mineral resource potential would receive definite consideration at the local level.

Jan 1, 1977

By Luis N. Henriquez

One form of encouragement for the small copper mining sector in Chile has been the construction and management of custom mill facilities to process the ore. The paper describes an economic analysis framework for the evaluation of government custom milling opportunities. Feasible mill locations and capacities within a region are selected and the infrastructure and milling costs associated with each combination of location and capacity are assessed. For each combination, the economics of developing and operating known copper deposits in the region is evaluated, and an optimum cut-off grade and mine capacity is selected for the deposits which justify development. Since the total ore supply from mines in the region may exceed a particular custom mill capacity, mine development is scheduled to optimize the economics of the mill facility. Finally, the best custom mill location and capacity is selected on the basis of overall costs and benefits. A copper mining region in northern Chile is used to illustrate the application of the model. A mobile mill approach is examined and compared with the fixed location mill alternatives. Results are analyzed as a function of copper price.

Jan 1, 1977

By A. Himsley

This paper presents a review of the existing ion exchange resin systems for treating unclarified pregnant liquor, with particular reference to uranium extraction. A new concept of a truly continuous ion exchange system is described and operating details are given,of a 0.6.-m (24 in.) diameter pilot plant treating unclarified acid leach liquor.

Jan 1, 1977

By Prakash C. Kapur

Many balling and gradation system6 generate self- similar size distributions of the agglomerates. Inspection of the experimental data shows that this is also true of the steady state distributions resulting from the granulation of coarse, partially wet powders, for example, the fertilizer feeds. This result is exploited in the derivations of a number of simple and useful relationships that are pertinent to the analysis of these agglomeration systems. The bonding liquid demand of the granulating charge is a third order polynomial function of the dimensionless ratio of feed particle size to median granule diameter in the weight-fraction distribution. The median size, in turn, is the scale factor or characteristic size parameter in the similarity distribution. The granule size distribution, therefore, is completely specified by the liquid content and the similarity function, and so are the process efficiency and the ungranulated component In the product at steady state.

Jan 1, 1977

By James J. Scott

Introduction Friction Rock Stabilizers, trade name Split Sets, are presently under research and development by Ingersoll-Rand Company and Dr. James J. Scott, inventor. Conceived in 1953, the system is a patented process undergoing extensive field and laboratory testing. The author has published papers on the Split Set System earlier (References 4, 5, 6) The Split Set System holds promise to be a revolutionary development in the field of ground control. The system produces an interior reinforcement to a rock mass which: 1. Is simple in its concept. 2. Adjusts to the degree of restraint needed to match rock properties. 3. Provides a yieldable support and, later, a more rigid support as it is needed. 4. Pre-loads the rock in compression to increase stability. 5. Is a full-contact, fully tensioned device to resist rock loads. 6. Minimizes the stress concentration effects inherent in many interior support devices. 7. Improves safety for the miner. 8. Is cheaper than a grouted system. 9. Offers the rock mechanics engineer an opportunity to design in a fashion not before possible.

Jan 1, 1977

By D. M. Watson

Mineral discoveries and subsequent extraction have led to the establishment of many small communities, some major towns and a few cities . In Canada, such developments have essentially occurred without benefit of long-range regional or local planning. In the past, this was not a cause for concern. Now, however, rising expectations and reorientation of social values have placed increasing responsibility on government and industry to ensure the long-term viability of communities and regions. Such responsibility means large investments by government in infrastructure and by industry in extractive and processing plants. Uncertainty in the interpretation of ore reserve estimates becomes a critical factor. The traditional methods of reporting reserves - "proven", "probable" , "possible" - may be useful in individual mine production planning, but they are inadequate for planning industrial and public infrastructure, The need for a better information base is critical, with clear and precise definitions of what is being reported, but we are a long way from achieving it. The challenge is therefore to develop a closer professional relationship between government and industry and to tie mineral development to long-range regional strategies.

Jan 1, 1977

In underground ore mining of copper ore, lead-zinc ore, tin ore and fluorspare in German Democratic Republic geological situation is characterized by ore deposits of small thickness and great variability of ore grades and mining conditions. For long range mining strategy and short-term planning of production a model was developed fitting to make optimal economic mining decisions. Starting point of the model is a cost function representing all direct costs per unit recoverable metal in concentrate for each stoping unit (ore reserve block). In the costs function the results of regression analysis of ore grade and metal recovery in concentration plant were considered. All stoping units (ore reserve blocks) of a mine were arranged to growing direct costs. The relationships of recoverable metal, ore tonnages and corresponding costs were plotted in a diagram. The data processed by- computer and the graphic representation of the results make possible 1. economic evaluation of stopes and ore reserve blocks, 2. estimation of cut off grade, 3. optimization of works planning.

Jan 1, 1977

By Donald W. Gentry

This paper presents some of the results of a rock mechanics in¬strumentation program designed for, and implemented at, longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam and immediately below the coal seam. Longwall test panel 411 had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft). The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) al¬though it ranges from 73-134 m (240 - 440 ft). Roof support at the face was provided by Hemscheidt shields. These shield-type supports weigh 11.4 metric tons each.

Jan 1, 1977

Provide an operator cab to assure protection, comfortable use of controls, and good visibility. Approach A cab which raises and lowers by pivoting about d horizontal axis was Installed on two S&S cleanup tractors and tested in two underground working mines. How It Works Hydraulic cylinders actuated by a lever inside the cab cause the cab to pivot about a horizontal axis. This action raises or lowers the cab height. The total cab excursion is 14 inches. A release valve in the hydraulic system allows the cab to lower automatically if struck by a roof load or overhead obstruction. The pivoting action of the cab is engineered so that the operator maintains comfortable use of all controls at all cab heights. The movement is such that the angular relationship of the operator's ankles With the tram and brake foot controls IS consistently within 90 to 100 degrees. Figure 1 outlines the approximate position of the operator at three cab elevations.

Jan 1, 1977