Search Documents

The Lornex mine is located in the Highland Valley area of British Columbia, Canada, one of the most,promising districts of low-grade porphyry-type copper mineralization in the world; Lornex is operated by Rio Algom Mines, Limited, a member of the Rio Tinto Zinc Group of London. Exploration from 1965 to 1968 disclosed an ore body of 293 million tons with a grade of 0.43% copper and 0. 14% molybdenum; this led to the decision to construct a 38,000 tpd operation, and production commenced in the fall of 1972. The ore is open-pit mined with 15 cu yd (11 5 m3 shovels, which load 100- and 200 -ton trucks. These trucks dump directly into a 60 in. by 89 in. Allis -Chalmers gyratory from two sides of the 14 ft 6 in. (4.42 m) deep dump pocket and across splitters mounted on the pocket sides. The unlined pocket would hold 1,000 tons level full. The crushedore discharges into a 300-ton surge hopper equipped with an automatic sonic level indicator to prevent over -filling. A 96 in. by 23 ft (2.44 m by 7 m) apron feeder delivers the ore from the surge hopper to a 72 in. (1.83 m) transfer belt equipped with a tramp iron metal detector. The transfer belt discharges to a 60 in. (1. 52 m) conveyor which conveys the ore about 3,000 ft (914 m) to the 475,000 ton ore storage pile located near the concentrator. Four 48 in. (1.22 m) pan feeders transfer the ore to the mill feed conveyors, which in turn supply the two 32 ft by 15 ft (9. 75 m by 4. 57 m) semi-autogenous mills, which easily accept the 10 in. (254 mm) product of the crusher. Each semi- autogenous mill is followed by a secondary ball mill. The unusually large open side setting of the crusher accounts for its 6,300 tph maximum capacity. Concentrator capacity is now 48,000 tpd. Eccentric removal is eased by the design of the door to the crushed ore pocket, which has the cart rails mounted on its outer surface and is lowered to a horizontal position in the pocket by an electric winch. The top of the door rests on wear bar covered concrete piers in the pocket. Another feature is a chute through the floor at the crusher base that extends into the crushed ore pocket. Dust and spills of ore on that floor during crusher repairs are easily swept into the crushed ore pocket. This feature is also used at Bougainville and Palabora and has been added to others after operation has commenced. The design follows the concrete rectangular box concept with four main service and maintenance levels shown in the sectional drawings, although a third additional section has been added at the maintenance

Jan 1, 1978

By Jr. Smith

Borates have been mined in the desert areas of California and Nevada for more than 100 years. To about 1890, playa surface mining provided the chief sources of boron minerals. Underground mining of colemanite and later of borax and kernite was predominate until about twenty years ago. Open pit mining of the large deposits of borax and kernite near Boron, California has been most significant for the past twenty years. Mining of colemanite in the Ryan, California area, near Death Valley, began in 1907. Following the discovery of the large deposits in the Boron area (about 1957), mining in the Death Valley area became nearly nonexistent. Only small tonnages were mined for special uses. Little mining was done in the Boraxo area near Ryan. The first claim was made in about 1915 In 1960 the area became the property of the Kern County Land Company, which was acquired by Tenneco Oil Company in 1967. In 1976 the various borate properties and claims in this region were acquired by American Borate Corporation. The open pit mine is now approximately 400 feet (121.9 m) deep, 3000 feet (914.4 m) long and 1000 feet (304.8 m) wide. The borates in the Boraxo pit consist primarily of three minerals. These are about 50% coiemanite (C2B6O11' 5H2O), about 40% probertite (NaCaB5O9.5H2O), and 10% ulexite (NaCaBcO9.8H2O). The colemanite, along with boric acid and high-grade coiemanite ore from Turkey provide the only sodium-free borates for production of textile grade fiberglas. When heated to its decomposition temperature, colemanite decrepitates to a fine powder. This provides the basis for the concentration process. The gangue minerals in this deposit are primarily calcite and clays, including bentonite. The ore body has a very low arsenic content.which is a desirable feature. Test work had been done with samples prior to the results discussed herein. This paper will discuss results of test work which were the basis for erection of a plant, and the subsequent plant operations.

Jan 1, 1978

INTRODUCTION Conditions for formation of porphyry copper deposits appear to have been propitious in the Appalachian orogen from the end of Precambrian into Middle Ordovician, and again from Middle Devonian into Mississippian. In the Appalachians we can now record the evolution of a porphyry copper province within a developing orogen, one that reached metamorphic and structural maturity by the end of Devonian. Fig. 15, after Irwin and Coleman (1972), locates that portion of the Appalachian orogen included in this study, and Fig. 16 illustrates general geology of the area. Deposits mentioned in Table 3 and in the text are shown in Fig. 16. Data presented summarize personal observations by the author, published descriptions of specific areas noted in the bibliography, and abstracts from Provincial assessment files. Sources of previously published data are acknowledged. Few comprehensive descriptions of individual porphyry copper deposits in this area exist, so much of the data presented is new to the literature. Porphyry mineralization has, for this chapter, been restricted to porphyry copper de- posits, although porphyry molybdenum de- posits (Clark, 1972) are also shown in Fig. 16 (Hollister, et al., 1974). Copper- molybdenum and tungsten-molybdenum skarns are also omitted to simplify discu sion, though each is known in the area studied. Gaspe Copper is included, however; min- eralization in this deposit is present in the intrusion as well as in the skarn adjacent (Bell and Scott, 1954). Porphyry deposits listed in Table 3 are included because of some important feature, although other deposits have been reported (e.g., Kirkham and Soregaroli, 1975 ) . Clearly, no table now compiled could be complete. The pace of exploration insures that new occurrences will probably be found. Summaries of features exhibited by intrusions shown in Table 3 should remain valid, however, since they appear representative and are based on an adequate number of deposits in the area studied. Paleozoic porphyry copper prospects (shown in Fig. 16) are more common, apparently, in the northeastern part of the orogen, rarely having been found south of Catheart or west of the Logan Line. Occurrences of molybdenum and other associated lithophile elements are, however, known to the south and west as well as further north. Killeen and Newman (1965), King (1970),

Jan 1, 1978

By Joklik, G. F.

Most publicity about the copper industry nowadays is focused on the adequacy of ore reserves and on excessive mining capacity. These concerns, stemming from public awareness of actual and potential shortages and oversupplies, relate to production rather than consumption. Perhaps the reason for this one-sided view is that copper is thought of as a commodity which is conspicuously traded in world markets, rather than as one of many industrial materials that serve today's rapidly changing technology. Copper differs from other widely traded commodities in that its real cost of production has progressively increased since World War 11. The reasons for the increase are identifiable by analyzing operations in one of the world's large producing centres, the copper province of Arizona. Another respect in which copper differs from some other commodities is that increases in demand occur less automatically in the case of copper than they tend to in commodities whose consumption is more directly related to population growth. The copper industry's current inability to generate and attract needed investment capital is attributable to these differences between copper and other commodities; it suggests that the concept of copper purely as a commodity is outdated. The key to the problem is better integration between the activities of copper producers and users. Depending on circumstances, integration takes various forms- for example, investment tied to long-term sales con- tracts between producers in developing countries and consumers overseas; common ownership of producing and manufacturing facilities in industrialized nations like the U.S.; and consumer-oriented research and marketing by the copper producers.

Jan 1, 1978

By James R. Evans

Forecasting demand is an art as well as a science, and much personal judgment is required. National forecasts made for sand and gravel, crushed stone, and/or aggregate may be misleading or unhelpful locally. This is because of significant variation in demand within different geographic and/or political areas in the United States, and/or the use of an inadequate data base and forecasting methodology. The best forecasts may be made for local or regional market areas, irrespective of geographic or political boundaries, provided a proper data base is available. The Bureau of Mines compiles detailed statistics on commodities sold or used in the construction industries and, therefore, is in an advantageous position to make national aggregate demand forecasts.

Jan 1, 1978

New Zealand China Clays operata a plant at Matauri Bay, Northland for the benefaction of hallosite clay. Production is several thousand tonnes per year of which about ten per cent per year is supplied to an expanding export market.

Jan 1, 1978

Provide optimum visibility of mining operations while maintaining protection and comfort for machine operators. Approach A cab with hydraulically powered variable-height control was developed and used on a loading machine in underground operations. How It Works The cab is attached to the vehicle on a horizontal trunnion located near the forward end of the cab. A hydraulic cylinder, controlled by the operator from inside the cab, pivots the cab about the trunnion providing variations of up to 16 inches in elevation. The nominal tramming position of the cab is with its underside 6 inches above the mine bottom. From this position the cab can be pivoted up, or down, so that its back end is elevated 10 inches, or lowered to the floor. (See Figure 1.) The cab encloses the operator for protection against both overhead and lateral obstructions, and it raises or lowers, allowing the operator to select the most advantageous cab height. The cab is angled inboard 30 degrees to the machine line of direction. The operator's seat swivels to allow view of the conveyor during loading. All controls are located within the cab and move up and down with it.

Jan 1, 1978

By Ta M. Li

How will phosphate producers in southeastern Idaho fare with growing governmental regulations and environmentalism of the late 1970's? With a similarity that is reminiscent of the battles between the coal industry and environmental-conservation groups earlier in the decade, Idaho's future growth and a nation's need for phosphate fertilizer products remain uncertain. The catalyst that brought the issue to the forefront was the preparation of an Environmental Impact Statement (EIS) addressing the development of phosphate resources in southeastern Idaho. Although the final EIS was published in August 1977, resolution of rational and orderly growth in this potentially vital region remains stifled as Secretary of the Interior Cecil Andrus virtually "sits" on it.

Jan 1, 1978

By L. J. Hoover

The objective of this study was to assess the health and environmental impacts of fluidized-bed combustion (FBC) of coal, specifically as applied to baseload generation of electrical energy by utilities. The study* was a short-term effort that based its analyses on information derived from the experience of the group or quickly obtained from the literature. The approach was to compare Atmospheric Fluidized-Bed Combustion (AFBC) and Pressurized Fluidized-Bed Combustion (PFBC) with two current technologies: low-sulfur coal combustion (LSC) and flue gas desulfurization (FGD) used with high-sulfur coals. A wet-limestone process was selected as the FGD technology. The impacts compared involved not only health and environment but also sociology, resource use, and dollar cost. Conditions for comparison were centered around a nominal date of 1988, when initial operation of commercial AFBC plants may occur. The PFBC has a later introductory date, a nominal 1995 (its impacts relative to other competitive technologies now in the R&D stages were not compared.)

Jan 1, 1978

By L. S. Rubin

The efficient and acceptable disposal of fine coal refuse (28MxO) is one of the highest priority problems facing the coal industry today. For many years the established system for the disposal of this fine refuse slurry has been to concentrate the solids in a static thickener and pump the resulting 20-40% solids underflow to lagoons or impoundments. Although this technique has served the coal industry well, increasing environmental concerns and refuse related disasters, such as Buffalo Creek, West Virginia and Aberfan, Wales, Great Britain have resulted in federal and state regulations which now control fine refuse disposal methods. As a consequence of these regulations, the capital costs of constructing, maintaining, and operating regulatory complying impoundments has become in many cases economically unattractive. Areas processing topologies similar to those coal preparation plants of the Appalachians are particularly burdened by these regulations and are consequently turning to alternatives for handling and disposal of their fine coal refuse. The basic requirements of impoundment alternatives as defined by environmental and plant demands are: (1) A relatively solids-free liquid (1000 ppm or less) to serve as plant make-up water in a "closed circuit" system, and (2) a sufficiently dewatered solids product which can be combined with the coarse refuse to form a compactable stable land-fill.

Jan 1, 1978

We often read and hear, especially in the United States, that we are running out of critical metals. These are vague forebodings of stagna- tion or winding down of our civilization. Our technological progress has been rapid in the last 50 years and is still advancing at an accelerated rate, and predictions of its long-term impact on consumption and production of metals are more hazardous than ever in the light of the great economic and political shifts that are bound to continue. There are many factors that will have a hardly predictable but profound effect on pro- duction and consumption of metals over a time span of, say, 25 years. Among such factors are recycling, substitution, availability of capital, direct involvement of governments in financing and production, and the capability of producing much lower grade ores at possibly much higher prices relative to costs in the event of scarcity. I must state at the outset that my discussion of this topic does not take into account the role that deep-sea nodules containing copper, nickel, cobalt, and manganese may play, because I don't believe production from these deposits will be of much significance within the 25 year span I will be discussing.

Jan 1, 1978

By F. L. Bazzanella

Cyprus Pima has two concentrators, one with a conventional crushing-grinding circuit and the other using semi-autogenous grinding followed by ball mills.

Jan 1, 1978

The developments in hydrocyclone classification in the milling circuit at Bougainville Copper Limited are discussed. A major change in cyclone size and improve- ments in operating conditions have been made. Test work has been carried out to assess the classification performance of a modified Linatex cyclone, Wemco cyclones and a two stage cycloning circuit. The use of a scalping cyclone, to remove coarse material from the present overflow product for regrind, has also been investigated.

Jan 1, 1978

'Nothing happens until something is sold' This statement is not original - it is a necessary orientation for marketing industrial minerals. The most important single philosophy of marketing is that it recognises the consumer as the starting point. Production orientation is concerned with producing products that the customer might buy. Market orientation is concerned with finding the needs of the customer and how they can be satisfied. The difference between the two approaches can be recognised in company structures but the most tangible difference is in the approach by a company to selling and development. In other words, it is the market that decides what can be done with a mineral. The markets requirements dictate what mineral, what grade and what price will be paid. Therefore it follows that when pricing a product we should avoid taking the basic cost and arriving at a final selling price through a series of standard markups (unless government insists on it). We should start with the price the market can stand and work backwards to find out whether you have a profitable product or one that will fail because it is too dear. Naturally a thorough understanding of production costs is necessary particularly when marginal markets are concerned.

Jan 1, 1978

By Gary E. Butts, Paul R. Smith

Introduction The design of a mineral processing flowsheet involves many factors. The importance of the sample can not be overemphasized. Competent and thorough mineralogical examinations are important as an aid in designing the test program. Designing and conducting the laboratory test program is basic to the design of the flowsheets. In the project under consideration a flotation pilot plant was conducted to prove the process and to provide a realistic prediction of metallurgical results. Moreover, the pilot plant operation provides important pilot plant design data. Finally, accurate and clear reporting is essential so that the information developed can be utilized advantageously by the client and the engineering firm. The design of a minerals processing flowsheet is a team effort. Engineers from the mining company, the research organization, and the engineering firm all contribute to the effort.

Jan 1, 1978

By Robert P. Vinson

The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.

Jan 1, 1978

By C. E. Jordan

The Tuscaloosa Metallurgy Research Center of the Bureau of Mines, U.S. Department of the Interior, is investigating the recovery of phosphate from beneficiation slime, as part of the Bureau's efforts to conserve mineral resources through increased use of wastes. Phosphate equivalent to about two-fifths of U.S. production is discarded annually in the wastes. Exploratory flotation tests on the plus 5-um fraction of a slime sample showed promise for a classification-flotation technique. Onsite classification tests at six phosphate washing plants were conducted with a two-stage hydro cyclone system designed to recover the plus 5-um material. The cyclone underflows contained 8.3 to 19.1 percent P2O5, and the recovery of the plus 5-um PZOS values ranged from 81 to 95 percent. The percent P2O5 recovery from the total slimes ranged from 38 to 47 percent. Batch-flotation studies are currently being conducted.

Jan 1, 1978

By Robert W. Freedman

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks' storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

By E. F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged mechanical dust collectors (scrubbers) with high dust collection efficiency and low energy comsumption for controlling dust in coal mining operations. All of the scrubbers described are similar in configuration and are powered by 6-hp, 2,000-ft3/min vane axial fans. Air pressure differential is less than 6 inches water column. Height of the scrubbers? including fan is less than 14 inches, width is less than 16 inches, and length is less than 45 inches. The flooded fibrous-bed scrubber achieved respirable (less than approximatey 7 µm) dust collection efficiencies of 95 percent. The small-diameter-cyclone scrubbers showed about 92 percent efficiency and can be best where excess water is a problem. The wetted brush scrubber showed 88 percent efficiency at low cost, and the wetted fan scrubber showed a slightly lower efficiency (87 percent) but offered the smallest size and cost. A suitable water droplet eliminator is described.

Jan 1, 1978

By G. M. Ritcey

Purification of solutions can involve various treatment methods. In the normal sequence of metals recovery by hydrometallurgy, the ore is initially prepared for leaching by grinding to the desired optimum mesh size as dictated by the leaching parameters. Following leaching and liquids- solids separation, the resultant solution is ready for purification. The use, or introduction of solvent extraction into a plant, can be either a major or a minor part of the metal recovery process as shown by the following list where solvent extraction is normally considered: a) recovery of a metal by a simple leaching of the broken ore, e.g., copper from dump leaching where there are only the three main steps of leaching, solvent extraction, and electrowinning (1);

Jan 1, 1978