Search Documents

The coking coal produced by Utah Development Company in the Bowen Basin is processed by a dual system of dense media cyclones for the 30mm x 0.5mm feed and flotation for 0.5 x 0mm material. The basic metallurgy of these processes will be presented with emphasis on the operational characteristics which are peculiar to coal. Potential areas for process improvement by the application of more sophisticated control systems will also be discussed.

Jan 1, 1978

By F. Matanzo

This guide considers only nine of the many wire rope terminations used in the mining industry so use of the information presented for terminations not specifically addressed can be done, but with some risk. The nine terminations considered are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Aluminum Sleeve & Thimble, Thimble Splice with Four Tucks, V-Bolt Clip with Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The guide uses pull test data, axial fatigue test data, and data on sensitivity to poor workmanship, to rank the nine terminations with respect to these performance measures. A selection procedure is suggested and illustrated with an example. Failure data is used to identify the common modes of failure of each termination and so help the inspector direct his attention to the likely location for a failure and describe what he should be looking for. The data on which this guide is based is included so that as new data becomes available, the ranking order can be adjusted accordingly.

Jan 1, 1978

By A. E. Hall, R. N. Taylor, J. G. Taylor

The introduction of tunnel-boring machines to South African gold mines has created problems and challenges which accompany any new technique. This paper describes the experience gained in this field, especially in the design and erection of a tunnel borer and in boring and environmental conditions.

Jan 1, 1978

By Desmond Y. M. Lee

This paper presents a procedure to prepare input for the computerized pit design system at Iron Ore Company of Canada. The procedure is simple and requires very little training. Also, it is general enough to accept both bench (horizontal cross section) maps and section (vertical cross section) maps. The output of this procedure is data which represent blocks of ore and waste with dollar values based on mineral content. The ultimate pit design is presented in printer-generated graphs, with numbers indicating the depths of pit bottom walls. Roads are added manually by the engineer with the aid of other computer programs. Section maps and bench maps are also printed as part of the output of the ultimate pit design.

Jan 1, 1978

Eliminate accidental tramming of a cleanup tractor. Approach A switch was installed in the operator's seat cushion to pre-vent the cleanup tractor from tramming without an operator in the driver's seat. How It Works The operator must be seated, and the Forward/Reverse Switch (that controls tramming direction) must pass through the NEUTRAL position before the vehicle will tram. See Figure 1. A pressure-sensitive seat cushion switch, a solid-state relay, and a double-contact relay were added to the control circuitry of an S & S BMUAT -88 cleanup tractor to create this tramming interlock. The weight of the operator on the cushion closes the seat cushion switch (Figure 2, A). This activates the solid-state relay (B), which completes the initial circuitry. Moving the For- ward/Reverse Switch (C) to NEUTRAL energizes the coil in the double-contact relay (D) and closes both contacts. One contact completes a sustaining circuit which keeps the double-contact relay energized. The second contact transfers power to the remaining contacts within the Forward/ Reverse Switch. These circuits are shown in greater de- tail in Figure 2.

Jan 1, 1978

The 74th Regular Meeting of the Rocky Mountain Coal Mining Institute convened at The Mark Conference Center, Lionshead Village, Vail, Colorado, and was in session at 10:00 a.m. Past President, Ralph Moore, Vice President, Operations, Westmoreland Resources, Hardin, Montana, called the meeting to order. The membership was asked to stand and pledge allegiance to the flag. He welcomed members and guests and thanked Park Lamborn, the Program Chairman, for the excellent speakers and program he engineered. He mentioned the cancellation of our golf tournament due to the conflicting dates with the Annual Jerry Ford Invitational Golf Tournament. He thanked all of the committees with a special "thank you" to Loren Linville and Gussie Whiteside. He introduced President, Shirl C. McArthur. President and General Manager, American Coal Company, Huntington, Utah. A biographical sketch follows: Mr. McArthur, a native of Huntington, Utah, began his coal mining career shortly after graduating from North Emery High School and worked his way up through the ranks, having worked at every job available underground. For example, he dug coal with a "banjo" at the Independent Coal and Coke Company in Kenilworth. In the summer of 1941, he worked at Straight Canyon Mine as a timberman and advanced to section foreman in four years. He was face boss for part of the time. In October 1946, he received a call from the LDS Church General Welfare Board (presided over then by Marion G. Romney) and took over as superintendent of the Church Mine. He operated in that capacity until the mine became privately owned in 1971. In 1961, Mr. McArthur formed Castle Valley Mining company, and in 1970, he organized American Coal Company, which he presently owns and operates.

Jan 1, 1978

Hamersley Iron Pty. Limited mines and pro cesses iron ore from two orebodies at Tom Price and Paraburdoo, situated in the North West of Western Australia. Conventional open pit mining methods are used at both sites in that material is drilled and blasted in benches, loaded by shovels and hauled to the Primary Crushers or dumped on waste or low grade material stockpiles. The present drilling fleet, consisting of eight high capacity Bucyrus Erie Rotary drills has evolved from an initial fleet of a large number of small percussion rigs. There are significant physical differences between the ore types encountered at both mines which nec- essitate the drilling of smaller diameter blast holes at Paraburdoo than those at Tom Price. The drilling practice at each site is dis- cussed, with examples of performance achieve- ments under varying drilling conditions.

Jan 1, 1978

By Roberts AW

Bulk materials handling operations depend on efficient storage and gravity flow facilit- ies. ,It is important that proper attention be given to the complete storage bin or stockpile and feeder combination. The paper briefly des- cribes the principles of efficient feeding and discusses the common types of feeders under practice. While ideally unaided gravity flow should be sought, occasions arise where flow promotion is necessary. Various types of flow promotion devices are described and their operational features evaluated.

Jan 1, 1978

By G. M. Ellis

When developing a mineral processing facility, the mining company management and engineering staff should have some knowledge of the construction industry in order to work with the contractors involved as a team. Of course, the situation varies with the nature of the project and its size, but relations among owners, engineers, and contractors always will be enhanced if the mining company has a knowledge of three construction industry facets: (1) the makeup of a construction company, (2) the functions performed by its staff, and (3) the various types of contracts and tendering procedures available. There are several options open to a company wishing to bring a new mine into production from the grass roots, depending upon corporate structure, capabilities, and financial strength. A company that already employs a substantial engineering staff may elect to manage and perform the design requirements itself, and may handle some or even all of the actual construction work. But in cases where bank financing is required, the loan is often dependent upon adequate professional construction help being used.

Jan 1, 1978

By David M. Parkes, Junie Lindsay

A review of the movement of coal in water is undertaken from a practical rather than a theoretical view point. Installations are described in which coal is transported on gradients down to 2.5' and others which move coal at a water-coal ratio of 1:l by weight. The water cycle of the hydraulic mining system is discussed. In many applications this can be a closed circuit. The coal dewatering system is illustrated, making particular reference to the problems of storage of coal-water mixtures between the mine and the plant. Water treatment is done in thickeners down to 100 ppm which is normally sufficient for re-circulating through high pressure pumps and monitors.

Jan 1, 1978

By W. R. McDonald

The Bureau of Mines, U.S. Department of the Interior, conducted small-scale field tests on acidic copper tailings as part of its effort to develop, improve, and demonstrate technology for stabilizing mining and mineral-processing wastes. Two successful demonstration revegetation plots were established on an abandoned copper-tailings pond located on public land adjacent to Holden Village, Wash. The tailings were neutralized with treatments of either dolomitic lime or limerock and fertilized with processed sewage sludge and/or commercial fertilizer. Excellent plant growths covering 70 and 24 percent of the surface were achieved on 1/8-and 1-1/2-acre test plots planted in 1973 and 1974, respectively. Regar brame, Tegmar intermediate wheatgrass, and tall wheatgrass provided the best plant growth and surface coverage. The target pH of tailings neutralization was 6.8; however, good plant growth occurred in areas where the soil pH ranged from 2.9 to 5.8.

Jan 1, 1978

By P. A. Croce

A total of 17 mine gallery fire tests (23 including sub-tests) were completed during this report period (10/1/76 - 11/30/77), directed at identifying a hazardous timber-set fuel-loading in a mine passageway that is otherwise free of combustibles. Results of these initial tests show that the capability of a particular fuel loading for propagating a fire is dependent upon the imposed ventilation air velocity and the ignition intensity, although this dependency needs to be better defined. It is also apparent that care must be taken when relating gallery test fire behavior to actual mine fire behavior, because of the restrictive length of the gallery. Present data indicate that some modification to the instrumentation scheme may be advantageous before proceeding with future tests.

Jan 1, 1978

By Rashleigh C

The selection and application of an effect- ive firing system first require a clear under- standing of the initiating abilities of the com- ponents in such systems. The conditions under which charges can be prematurely initiated by a detonating cord downline must be appreciated. This is a principal consideration in the design of a successful downline/'Anodet'/primer assembly. The advantages and limitations of an electric and several non-electric initiating systems are explained. The factors which in- fluenced selection of the two most suitable systems for use at Isa Mine (viz. downline/ 'Anodet'/primer assemblies and the reinforced long-lead 'Anodet'-type delay system) are dis- cussed. Blasts are detailed in which each of these has been applied. The initiating design for a hypothetical 2 x 106 tonne blast using electric short delay detonators and multi-channel exploders is presented. In this design, charges in remote blastholes are activated after the detonation of earlier firing charges by protecting the firing lines with sandbags.

Jan 1, 1978

By A. K. Haines

The status of the South African research and development programme on continuous ion exchange, which was aimed at the technical and economic assessment of that process for the recovery of uranium, is reviewed. The first phase of this programme, which has now been completed, involved development investigations on various pilot plants and culminated in the successful operation of a large-scale demonstration plant and the incorporation of the system in a number of new South African uranium plants. This account highlights the engineering aspects and the design fo the system, its adaptation to process flowsheets, and plans for future development.

Jan 1, 1978

By T. Tanaka, H. Kiuchi

The combination of the following two exothermic reactions was studied with the purpose of recovering H2 from H2S formed in acid leaching of sulfide ores, direct reduction of metal sulfides with H2 or desulfurization of crude oils: In the kinetic study of the recovery of H2, the reaction rate was measured by the two methods of single-stage and circulation blowing of H2S through molten Pb in the temperature range of 550 to 750°C. The experimental results showed that the rate determining step is in the chemical reaction itself and also that this reaction is accelerated markedly by the addition of a trace of Ni, which may be responsible for the catalytic action of Ni dissolved in molten Pb. In the experiments where Pb metal was produced, PbS was oxidized in a stream of atmospheric N2 containing 0.5 to 20 vol-% 02 or in the same 02 partial pressures as in N2 though under reduced pressures in the temperature range of 400 to 800°C. It was found from these experiments that the formation of PbSO4, basic sulfates and PbO are suppressable to yield Pb metal alone above 750°C and for 02 concentrations of less than 1 vol-%. Vapor of PbS was thought to take an important part in the Pb formation mechanism, and the probability thereof was demonstrated thermodynamically.

Jan 1, 1978

By J. B. Davis

Isotope analyses distinguish biogenic sulfur ores from non-biogenic ores, but do not distinguish bioepigenetic from biosyngenetic ores. Sulfur deposits of salt dome caprocks and of bedded Permian evaporites of west Texas, however, are clearly bioepigenetic. Anhydrite, introduced by salt diapirs into geologically younger sediments, is converted biogenically to sulfur and calcite in the presence of petroleum; for example, in Challenger Knoll, a salt dome at a water depth of 3600 m in the Gulf of Mexico. Bedded evaporites of west Texas in association with petroleum show an obvious epigenetic replacement of the anhydrite layers by biogenic sulfur and calcite

Jan 1, 1978

Experimentation with new methods, materials and machines to improve primary drilling and blasting is a continuing practice in the hard rock quarry operations of the BMI Group. These experiments will continue in the remote hope that one day we may produce a perfect feed for the primary crusher. As this day is still a long way off, the necessity to break oversize boulders will be a problem to be faced for the foreseeable future. To gauge the efficiency of primary blasting from this point of view, BMI monitor the tonnes of material crushed in the primary crusher for each boulder requiring secondary breaking. Over a period of about 10 years, this figure has improved from 30 tonnes througi the primary crusher per boulder, to 100 tonnes per boulder at our largest operation, which produces in excess of 2 million tonnes per year. Evan with this improvement, 25,000 boulders require secondary breaking each year This paper does not provide the solution to this problem, as like primary blasting, it will have to be constantly reviewed as new products and techniques become available. The paper sets out all of the methods tested or considered for test by BMI and our nnnn1iicinnq nn Chair PffPr.tivPness . Economic

Jan 1, 1978

By M. G. Adamson, B. D. H. Phillips

This paper describes a procedure that has been found successful in the planning and execution of practical trials of mechanized-mining equipment. The procedure is illustrated by reference to development trials of a rockslotting machine with pneumatic or hydraulic drills that were conducted on South African gold mines.

Jan 1, 1978

By Wayne A. Van Voast

Many coal beds that will be mined in southeastern Montana are aquifers that provide essential local water supplies. Mine cuts along aquifer outcrops create almost imperceptible piezometric changes. Monitoring near such operations at Colstrip has detected almost no water-level declines in observation wells. Mine cuts between outcrops induce rapid storage depletion and associated piezometric depressions. One such cut near Decker induced 1,250 m3/day of flow from storage and created a piezometric depression of 3 meters or more as far as 1,500 meters from the mine. No wells have yet become non-productive but losses of some are inevitable as operations expand. Alternative supplies are available from aquifers stratigraphically below the disturbed materials. Effluents from active mines are chemically similar to other area waters because they are mixtures or ground waters entering the mine cuts. Occasional high concentrations of nitrate do occur, however, as residuals from explosives. Spoils generally consist of confined aquifers of wasted coal and coarse rubble at their bases, overlain by finer-grained sand, silt, and clay. Hydraulic conductivities and storage coefficients are comparable with those of undisturbed confined aquifers. Water quality in mined lands is highly diverse because of diverse spoils lithologies and poorly-established ground-water circulation. Ground water in spoils is more mineralized than in the coal beds and chemically resembles waters from sandstone aquifers. Hydrologic effects of mining will not be catastrophic or widespread but may have local significance. Most notable changes will be in water quality; availability will not be permanently reduced.

Jan 1, 1978

By Rhual L. Guerguerian

MINING has been practised by mankind for over sixty centuries (1). In 1876, the "ball mill" was patented, and during the century that followed rotary grinding developed to the state where individual machines are treating tens of thousands of tons of ore per day. This paper gives a brief description of design practices prior to the availability of advanced facilities, followed by modern analytical design development at Dominion over the past ten years.

Jan 1, 1978