Search Documents

By J. H. Perry, Joseph Cervik, G. N. Aul

The Bureau of Mines is conducting research to determine the effectiveness of long holes in degasifying an area of the Upper Split of the Lower Sunnyside coalbed at Kaiser Steel CO.'s Sunnyside No. 1 mine. These holes were drilled from the two outside entries of a section that was closed to mining because of excessive methane emissions. Two holes drilled to 430 and 450 feet produced initial gas flows of 160,000 and 127,000 cfd, respectively. Sixteen days after the completion of the second hole, the total gas production declined to just over 144,000 cfd. In 9 months of degasification, over 35 MMcf of commercial-quality gas has been removed from the coalbed. The combined gas flows declined to 106,000 cfd in the 9-month period. The two holes have reduced face emissions by about 40 pct.

Jan 1, 1978

By D. B. Stewart

In the past few years, much effort has been spent in elucidating the impact of diesel engines on the mine environment. This paper summarizes diesel fundamentals , exhaust emissions and typical tailpipe concentrations. Mine sampling results and an evaluation of exhaust treatment systems are discussed. A review of changes in pollutant concentrations between the tailpipe and the mine exit is made and suggestions are given to reduce operator exposure to diesel contaminants.

Jan 1, 1978

By Jim Davis, Calvin J. Konya

The methods used to confine the gases within a borehole can influence the amount of useful energy obtained from the explosive charge. Improper confinement not only wastes energy and raises cost but also can result in airblast, excessive ground vibration, flyrock and boulders. The type of stemming material and amount of stemming used will definitely influence the degree of confinement and the efficiency of the blast. In order to extract the maximum energy from the expanding gases, the stemming plug should never blow out and allow the gases to escape prematurely.

Jan 1, 1978

By Earl G. Hoover

For most geologists and miners the term "asbestos" refers to a group of highly fibrous silicate minerals that readily separate into long, thin, strong fibers of sufficient flexibility to be woven, are heat resistant and chemically inert, and possess a high electric insulation and therefore are suitable for? uses where incombustible, nonconductive or chemically resistant material is required. The United States Mining Enforcement and Safety Administration (MESA) specifically refers to the naturally occurring minerals chrysotile. amosite, crocidolite, termolite asbestos, anthophyllite asbestos, and actinolite asbestos as "asbestos" if the individual crystal fragments have the following dimensions; length -greater than 5 micrometers, maximum diameter -less than 5 micrometers, and a length to diameter ratio of 3 or greater. Since asbestos has been identified as one of the ten most carcinogenic substances (a cancer causing agent) it has become, for many government regulatory agencies, a major issue concerning banning emissions to the environment.

Jan 1, 1978

By W. W. Harvey, F. O. Dudas

Toward hot hydrochloric acid, the usual order of reactivities of the common copper sulfide and associated minerals is reversed, and the rates of H2S formation vary as [ ]. The iron component of chalcopyrite and bornite reports to the solution as ferrous chloride, while pyrite remains essentially unreacted. If a pressure of H2S is maintained in the reactor, copper solubilization is suppressed, and the primary copper sulfides are converted to finely divided secondary sulfides (principally covellite). The HCl leach reside then consists mainly of covellite, pyrite and acid-insoluble gangue. Copper can be selectively leached from this upgraded concentrate to yield a clean, strong copper sulfate solution for direct electrowinning. Preliminary analysis indicates competitive economics with respect to established hydrometallurgical processes. Other concentrate treatments based on an initial HC1 leach are proposed and relative advantages compared. The common denominator of the major process routes considered is the requirement to regenerate HC1 from an FeC12 solution. Five distinct concentrate compositions were employed in the experimental study, which included some attention to the fates of selected minor constituents of the copper concentrate, especially gold, silver, molybdenum, arsenic and selenium. Significant mineralogical features of reactants and products are described.

Jan 1, 1978

By Donald H. Matthews

The usual method of dismantling massive concrete formations with explosives, is to totally demolish the entire concrete structure. If any portion of a concrete structure is required to remain in its original form and retain its structural integrity, the use of explosives is usually forbidden and the portion to be dismantled is demolished by mechanical means, using various techniques and equipment that are tedious and expensive.

Jan 1, 1978

By J. C. Bowling

The services provided by consulting engineers to the mineral process industry are briefly described. The organization of a multi-discipline consulting firm is outlined. Finally, the role of a consulting engineering firm is amplified by a description of its activities in the design and construction of a mineral process plant from inception to start-up.

Jan 1, 1978

By G. M. Ritcey

Continuous contacting equipment for solvent extraction can be divided into two major areas, according to whether their mode of operation is stagewise or differential (Figure 1). Mixer settlers and the recent Kenics and Sulzer mixers typify the stagewise contactors. In these counter- current contactors, the aqueous and the organic phase are mixed and then separated in a large settling area before the next stage of mixing. Countercurrent differential contact- ors, such as centrifuges and various types of columns, are more compact in that they require less ground area than mixer settlers. [ ] Contactors, in addition to being either stagewise or differential, can be further subdivided into non-agitated and agitated depending on the method used for mixing the phases and producing the countercurrent flow. The simplest contactors such as spray, packed, or perforated plate columns achieve both the mixing and countercurrent flow by means of the gravity difference between the two phases. In agitated contactors such as the Scheibel, Reciprocating Plate, and Sieve-Plate Pulse, mechanical agitation is introduced but gravity differences still produce countercurrent flow. To conserve plant space, and for large throughput with short contact time, centrifugal contactors are used where possible. The reader can refer to reviews on the subject (1-11).

Jan 1, 1978

By A. R. MacLean

This mine is situated at Point Aconi, Cape Breton , Nova Scotia, and is a replacement for the 100-year-old Princess Collie ry. It is a slope mine which is the continuation of a s trip mine operation. There are fives lopes from the surface driven with Dosco Dintheaders - this marks the first time these machines were used in North America. There are four room -and-pillar sections, each equipped with a Lee Norse HH106 continuous miner, a "Top Dog" roof bolter and two Wagner diesel Teletrams. There are also two Eimco 913 diesel LHD's , which are used for clean-up in the mines. This paper describes the mining operations of this 800,000-tpy mine which, in less than a year and a half , has been developed to the stage where four sections are producing coal at the desired rate.

Jan 1, 1978

The paper covers the history and develop- ment of electrical and diesel-powered hydrau- lic percussion rock drills. It examines main design aspects and problems encountered in pro- ducing an efficient and reliable machine to fully cover the nominal hole sizes required for underground development, production drill- ing and for general quarry work. The main design features and advantages of a hydraulic rock drill are relatively low input power requirement to energy per blow (this being achieved by the use of an electric or diesel- powered hydraulic system) and a specially con- structed piston using a powered damper cylinder to absorb the recoil forces from the drill steel and reduce stresses on the drill, feed and hydraulic boom. A further important design feature is the anti-jamming device which controls the drill both during manual and automatic operation. This anti-jam device works on feed and rotation press and prevents the drill bit becoming jammed in broken or soft ground. These features and many other mechanical and environmental benefits are highlighted when comparing hydraulic percussion rock drills with current pneumatic machines. The hydraulic rock drill gives an overall high penetration and production rate, with an added bonus for ergonomy and environmental conditions such as lower noise level, no fogging from air and oil exhaust (which naturally gives better air for breathing),plus improved vision when in under- ground situations. Hydraulic rock drills and systems have been fully tested in many mines, quarries and contract sites during the past years. They h6! been improved and modified and are now provi~ to be very reliable and economical piece drilling equipment whò in mines and quarries.

Jan 1, 1978

By H. W. Brandt

A field test was designed to inject a specially formulated two compound epoxy resin into the roof rock ahead of a working face to cement fractures and formation interfaces at the Westmoreland Coal Co., Winding Gulf Div., Eccles No. 5 Mine, Eccles, West Virginia. Five 30 foot long X 2 inch diameter, hold were drilled at an angle of 15° above the plane of roof line front the face of a working entry. The epoxy resin compounds were pumped through a proportioning unit and mixed in-line before being discharged into the drill hole under treatment it injection pressures up to a maximum of 450 psig. When the coal face was advanced an anomalous failure of the roof rock occurred in the treated section. Further testing was suspended until the cause of the failure could he determined. The polymers were tested, under confined conditions, in 2 inch pipe columns. Extreme temperature and pressure (up to 2400 psig) rises were recorded as they cured, It was concluded that this pressure source fractured the rock and caused the roof failure. The entire program was terminated after it was determined that the heat rise and resultant high pressures could not he controlled chemically or mechanically.

Jan 1, 1978

By Gus L. Maciula

Although I will briefly review the current status of coal slurry pipeline technology, I wish to make it clear that this is not a technical paper. It is intended instead to review the current situation on energy resources and requirements, and the environmental, political and economic considerations that mandate a serious consideration of Slurry pipelines as a viable mode of coal transportation into the Georgia and Florida markets. In order to more fully appreciate our current energy situation, it will be helpful to go back a few years and review the evolution of our so-called energy "problem." It was about two decades ago that the first and only major natural gas transmission pipeline was built into the State of Florida by Florida Gas Company. This line was conceived and implemented during a time when gas was plentiful and cheap, and it appeared at that time that unlimited gas reserves were continually being discovered, thus assuring the availability of a clean, cheap fuel and the ,viability of the pipeline system. One of the major factors justifying the original pipeline construction as well as subsequent expansions was a series of long-term commitments under which Florida Gas transported natural gas owned by electric utilities for use as boiler fuel. Thus for the past 20 years Florida industry, commerce, and domestic fuel requirements have been met either directly or indirectly through clean, cheap natural gas which would not have been otherwise available without the pipeline system.

Jan 1, 1978

By Daniel R. Shawe

Ore deposits of the western U.S. are divisible broadly into two genetic groups, a smaller one that fits the plate tectonic model of subduction and a larger one that appears unrelated to subduction. Some of the middle Paleozoic and lower-middle Mesozoic ore deposits in the western U.S. are associated with eugeosynclinal rocks and lie a few hundred kilometers west of reconstructed continent margins. These deposits probably formed as a result of subduction beneath oceanic or thin continental crust that was analogous to subduction predicated for the Kuroko massive sulfide deposits of Japan. Some middle Mesozoic porphyry copper deposits may have formed east of the continental margin when subduction-generated magmas were emplaced high in continental crust in a manner analogous to subduction-generated magmas that formed the Andean porphyry copper deposits. Most Cretaceous-Cenozoic ore deposits lie in a broad region extending many hundreds of kilometers east of the continent margin and characterized by conjugate tectonic zones, high terrestial heat flow, and low seismic velocity in the upper mantle. The deposits likely were formed in relation to magmas generated along the conjugate tectonic zones during differential northwestward drift and internal wrenching of the continental plate.

Jan 1, 1978

By E. Robert Kiehl

In the early days of the United States, gypsum was most commonly used for the manufacture of plasters with energy being used for quarrying, grinding, and calcining of gypsum rock. With the dramatic switch to gypsum-drywall construction after World War II, the energy usage per ton of rock processed increased more than threefold, and with the rapid growth of the construction industry, the total energy consumption in gypsum-board production alone increased eightfold during the period from 1940 to 1973. The gypsum industry was one of the first to recognize the need for energy conservation and has voluntarily reported its progress to the Federal Energy Administration for the past several years. Efficiencies in the use of energy have resulted in decreasing the unit consumption an estimated 10 percent during the past six years. Improved combustion efficiencies, optimum operating conditions, more liberal use of insulation, and heat recovery will all contribute to the gypsum industry's goal of using less energy. Gypsum products today are vital to over 85 percent of new housing construction in the United States.

Jan 1, 1978

By Phillip N. Yasnowsky

This Bureau of Mines publication tabulates State taxes levied on nonfuel minerals that have the characteristics of a severance tax.

Jan 1, 1978

By C. H. McGuirk

Although preventive maintenance is not a new concept and has many proven applications, it is believed that the Pittsburgh & Conneaut Dock Co.'s Computerized Preventive Maintenance System is the first and possibly the only application related to heavy duty bulk material handling equipment. This paper is presented to describe the development, installation, and application of a Computerized Preventive Maintenance System applied to an 18 million t (20 million st) coal and iron storage and reclaim facility located on the shores of Lake Erie at Conneaut, Ohio.

Jan 1, 1978

External pressures are being exerted on busi- ness, and especially the mining and energy in- dustries, as never before. These pressures are burdensome, they emerge in unique forms, and they constitute an entirely new operating environ- ment for business. They pose one of the signi- ficant challenges to senior management today. To cope with these pressures-which we have termed the new public realities-we must deal more effectively with the media, the public, and government. However, before examining methods for improvement, it is essential to understand the nature of these new public realities and par- ticularly their determinants-the underlying eco- nomic, sociological, political, and international events and trends which have shaped them. Previously the productive element of society had only to concern itself with what might be termed `conventional realities' : the costs of labour, equipment, and land, as well as marketing and distribution factors.

Jan 1, 1978

By T. Iwasaki

This paper points out two key elements in resource trade in general and the Canada-Japan relationship in particular. The first is that the advanced countries have a more important role than one would expect in the supply of resources in world trade. Canada 's dual role as a major resource supplier in conjunction with an advanced economy will continue to increase. The second point is the heavy reliance on foreign resource supplies in some advanced economies, particularly in Japan. Finally, as regard the future of the Canada-Japan economic relationship, particularly .in resource development, it is suggested that trade could be enhanced by an accelerated exchange of various types of resources between the two countries. These include natural resource commodities as well as the more abstract capital, technological and human resources.

Jan 1, 1978

By Robert L. Tremblay

Dans le but de voir si une région comme la Gaspésie, qui a subi la derniere glaciation , se prête avantageusement à la méthode de prospection alluvionnaire, environ 800 concentrés de minéraux lourds furent prélevés dans les districts électoraux de Matane et de Gaspé-Nord. Les différentes phases minérales présentes dans les concentrés ont été examinées à la loupe binoculaire. Afin de mieux valoriser ce type d'inforrnat ion, nous avons été arnenés à expérimenter et à mettre en oeuvre des techniques multivariables adaptées au traltement d'une information semi-quantitative en utilisant le principe d'un codage logique préalable. La structuration des résultats de la Gaspésie a conduit à l'élaboration de cartes de synthèse qui constituent un support nécessaire à l'interprétatlon des répartitions plus ponctuelles des minéraux "utiles" sur le plan de la recherche minière.

Jan 1, 1978

A system to continuously measure the concentration of radon in mine ventilating air has been developed and tested in a uranium mine. In use, the air/radon mixture to be monitored is pumped through filters into a scintillation cell where nuclear decay of the radon produces flashes of light. These are electronically counted, giving a quantitative measure of the radon present. Air is continuously drawn from the mine atmosphere into the radon sensor box. This air sample passes through two filters into the detector cell as shown in the schematic diagram. A portion of the radon in the detector cell will experience nuclear decay, producing polomium 218 and an alpha particle. The alpha particles from the fraction that decays strike a zinc-sulfide coating on the inside wall of the cell and produce flashes of light. These enter a photo-multiplier tube which records each flash as an electrical pulse. An amplifier increases the voltage of each pulse, allowing electronic screening to remove noise and other undesirable pulses. The remaining pulses are counted by a conventional data acquisition system.

Jan 1, 1978