Search Documents

By J. L. Holman

The Bureau of Mines has extended its previous development of cast Mn-Cu damping alloys to powder metallurgy (P/M) consolidation of alloys containing 55 to 75 wt-pct Mn. Blends of minus 200-mesh elemental powders were compacted cold in directional and isostatic presses. With 1 pct binder, typical green densities ranged between 76 and 80 pct of theoretical when pressing at 30 or 48 tsi. Green strength increased with compacting pressure and copper content. As-sintered tensile strengths ranged to 60,000 psi fox a hydrogen, sintered 60Mn-40Cu alloy, along with 5-pct elongation. Sintered densities ranged between 90 and 96 pct of theoretical. Sintering (a as effective when holding for 1 hr at maximum temperatures of 900° to 1,040` C, dependent on composition. Strength and ductility were considerably lower than for equiva¬lent cast alloys. When aged to the damping condition, alloys containing 60 to 70 pct Mn exhibited >40 pct specific damping capacity (SDC) at 5,000-psi stress, considerably higher than values reported for equivalent cast material. Effects of 1 or 3 pct Sn or Zn additions on SDC and other properties were assessed. Trials were conducted on consolidating rings and gears of the 65Mn-35Cu alloy on industrial-type P/M equipment.

Jan 1, 1979

By J. S. Dunning

A primary goal of the Federal Bureau of Mines is to minimize the requirements for scarce mineral commodities through conservation and substitution of more abundant elements, such as iron and molybdenum. One example of this is the research effort to devise substitute materials for specialty alloys, thereby conserving nickel and chromium in high-volume stainless steels. As a possible substitute for the solid solution strengthening of chromium and nickel, the precipitation hardening characteristics of a number of binary iron-based systems in which Laves phase precipitates, such as Fe2Mo, are formed were investigated. Several hardening responses were observed, but none were ideal. The Fe-Ta binary system had the highest magnitude of hardening, even with low alloy additions, and the Fe-Mo system had unique stability at temperature. Accordingly, the Fe-Mo-Ta system was selected for study to determine if a ternary Laves phase could combine high hardening with long-term stability at elevated temperature. Hardening and stability were reflected in excellent elevated temperature, tensile, and stress rupture strengths. Future research will study ternary systems based on more abundant resource materials, such as the Fe-Mo-Ti system, together with additions, such as aluminum and minimal chromium, to provide oxidation resistance.

Jan 1, 1979

By D. J. Dollhopf

This research was part of an effort to investigate means of reestablishing non¬polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. Chemically undesirable overburden material was selectively backfilled with the intent that it would be below the future root zone, be above the reestablished aquifer, and would not be leached as a result of deep percolation. After 2 years the buried material remains above the spoil aquifer and below the maximum rooting depth. Unsaturated water flow from the land surface to the buried material occurred during wet climatological periods. No significant leaching of buried material was observed, however. Overburden sample contamination from drill stem joint grease with Pb, Zn, and Cu additives caused substantial error regarding DTPA extractable trace metals. A grease with teflon and talc additives was recommended for use in future sampling programs. DTPA extractable trace elements in overburden material had no statistical relationship to post-mine ground-water quality. Overburden columns leached with water produced leachates comparable to overburden and spoil ground-water trace metal quality. A depositional model described the Rosebud Coal overburden as a fluvial system with distinct units of sand, silt, and clay, with distinct chemical properties. Physical and chemical characteristics of the model were comparable to the in situ geochemical system, a relationship which may aid in locating overburden materials unsuitable for reclamation.

Jan 1, 1979

By Bruce T. Stanley

A key point in the design and operation of a modern mining operation is the construction of what is called an ore-body model or block model. This model is a representation of reality constructed from predicted information. The blocks involved are merely subsets of the overall model which allows manipulation of the contained information on a local scale. In general, block models enable mine planners to effectively select the most promising means of extracting the ore both physically and economically. The uses of a block model can be quite diversified, but one must realize that a single model that satisfies all curiosities and forms of expertise is difficult to construct.

Jan 1, 1979

By Donald H. Sargent

This paper focuses upon the changing character of the market for Western bentonite, and upon transportation methods and costs affecting this market. The basis for the data in this paper, in addition to public sources of information such as federal and state government agencies and the open literature, was a program of 57 face-to-face interviews with individuals knowledgeable in the bentonite production, consumption, and transportation industries. The study was performed in 1974 and 1975 by Versar Inc., for the Bureau of Land Management, Department of the interior.*

Jan 1, 1979

By Ralph Bernstein

The processing of earth observation sensor data by digital technology is almost two decades old. Only recently, however, has this technology become practical and economical. The reasons for this are interesting to analyze, and they provide some insight into what the future may bring. Some of the earlier activities and their limitations, current systems and their applications, and future technology direction are summarized.

Jan 1, 1979

By Wilton Johnson

The development and use of minerals and mineral fuels are essential to national security and to the maintenance of an expanding economy. As a Nation, we often met these needs but failed to recognize and assess the impact that mining and mineral processing activities have on other natural resources. Currently, the growing demand for energy and minerals is accompanied by an increasing awareness that the provision of these resources must not conflict with society's demand for a clean and habit-able environment. Although present mining and mineral processing activities incorporate, or have under development, technology capable of minimizing environ-mental impacts on land, air, and water, many older operations, particularly in the first half of this century, lacked the technological, social, and environmental insights that exist today. Consequently, a substantial backlog of damaging and potentially damaging conditions remains from such problems as mine subsidence, acid water generation, burning and nonburning waste banks, abandoned surface-mined lands, abandoned underground mine fires, and abandoned mine shafts and oil and gas wells.

Jan 1, 1979

By Arthur B. Campbell

This Bureau of Mines report describes a method that utilizes a computer program to evaluate integral Gaussian profiles of atomic concentration versus depth in a solid. The specific use illustrated involves profiling ion- implanted metals using proton-induced X-ray emission (PIXE) analysis and ion sputtering (IS) for sectioning

Jan 1, 1979

It is no longer possible to establish a quarry on the most convenient hill then abandon the site, leaving a scar if the stone or sand in the deposit is found to be unsatisfactory. Before approval is given to operate a new quarry, the relevant authorities require a detailed plan of operations from commencement to final rehabilitation. To prepare this plan, a thorough know- ledge of the quality and size of the deposit is required. To obtain this information, the industry must use the most modern techniques available. Many examples can be given showing problems which have affected the smooth operation of a quarry for many years because the initial exploration was poorly carried out. The factors which must-be considered when exploring a deposit are detailed in this Paper.

Jan 1, 1979

By James R. Jones

The Surface Mining Control & Reclamation Act is a complex piece of legislation signed into law on August 3, 1977. It is the culmination of more than six years of debate by the Congress over the need for a national regulation of surface mining as opposed to the prior concept of regulation by each concerned state. It departs from the more normal type of law in that it includes very specific requirements, limitations and performance standards. In its procedural aspects, it is somewhat similar to the Clean Air Act and the Water Pollution Control Act in that it places primary responsibility at the state level, provided the state meets minimum national requirements. At the time of writing this paper, in late December 1978, the Interim Regulatory Program has been in effect for seven months. The proposed regulations for the Permanent Program, the draft Environmental Impact Statement, and the draft Regulatory (Economic) Analysis ware available for eight weeks before the close of the comment period on November 27. We are now awaiting issuance of the final versions of these documents. The states in which coal is mined, for the most part, have made sere revision to their state laws and are in the process of revising their regulations, or have just completed the revision, to comply with the Initial Regulatory Procedures. They are now faced with another new major effort to analyze and plan for compliance with the Permanent Regulatory Program, which is expected to be promulgated by the Office of Surface Mining of the Department of Interior by the time this paper is presented.

Jan 1, 1979

By Michel David

Once a mineralized body has been delineated, drilled and estimated from surface samples, it often happens that before the final go-no-go decision is taken, an underground sampling program is decided, very often via a ramp which hopefully will be later used to extract the ore. The cost of such a program can be close to a million dollars. On other occasions, when a property changes hands and is reexamined maybe 20 years after the original drilling program, a "check sampling" program is carefully, designed to make "sure" that the old assays are "correct". One may fear poor sampling practice in old days, or deliberate highgrading by promoters. Again one may be talking of resampling cost which may be in the six-figures range. Other similar situations include the drilling of a few large diameter holes to ascertain the validity of a majority of small diameter drill holes, or auger drilling, or back-rimming. In uranium checking radiometric information is also a problem related to the above ones.

Jan 1, 1979

By F. F. Peng, A. D. Walters, M. R. Geer, J. W. Leonard

INTRODUCTION Washability characteristics derived from float-and-sink analysis in Chapter 4 demonstrate that coal is intrinsically heterogeneous, and this heterogeneity is also evident in the proximate, ultimate, and size analyses. A range of particles from high to low specific gravity is usually seen in the run-of-mine coal. One objective of coal preparation is to recover the high quality float material (the particles of lower specific gravity) such that the recovered product meets certain quality specifications, as well as to reject or recycle low quality particles of higher specific gravity. The maximum recovery of cleaned coal at the required quality is of major concern to plant operators. However, the quantity and quality of products of coal cleaning, determined in the operation of actual commercial cleaning plants and by theoretical calculation based on run-of-mine washability studies, are known to be different with each coal. Therefore, during the last half century, coal preparation engineers have repeatedly sought methods to predict the technical and economical efficiency of separation of cleaning equipment and systems. Many formulas have been proposed by international investigators to evaluate the efficiency of various coal cleaning operations, primarily based on the yield and/or ash of the various products of coal cleaning. Performance criteria in use today are capable of defining all of the important aspects of a given concentrating operation; however each criterion has certain restrictions or limitations. It is important, therefore, to understand how such formulas can be used and the problems involved in their construction. Technical Measure of Plant Performance Conventional means for evaluating a preparation plant's performance are generally approached through the use of equipment performance mea-

Jan 1, 1979

A schematic overview of the variables which interact to determine ore reserves precedes consideration, in this context, of some recent views on the concept of a 'production cycle'. Political and governmental action, for whatever motives, is a greater obstacle to future mineral supply than technical problems.

Jan 1, 1979

On November 9, the Reynolds Metals Company cut production by 12 at its primary aluminum smelters at Troutdale, Oreg., and Longview, Wash., as a result of an earlier 25% power cutback by the Bonneville Power Administration due to lower than normal stream flow in September, the Aluminum Company of America had closed one potline at its Vancouver smelter because of the power cutback. Nearly 700 union workers at Anaconda Aluminum Company's primary aluminum smelter at Sebree, Ky., walked off the job when their contract expired or, November 15, after rejecting a proposed 3-year contract. The smelter has an annual capacity of 180,000 tons mid accounts for 50% of Anaconda's aluminum production. No talks are scheduled.

Jan 1, 1979

By Arthur L. Raub

During the last decade, there haven't been any great innovations in the design features of a copper concentrator. What has worked well in the past continues to work well, so that major breakthroughs have been minimal. Conservatism in the ranks also plays an important part. As a copper concentrator is not designed and built everyday, Davy was elated to have an important part in this project. This is the story of the design of the oracle Ridge Project located north of Tucson on the back of Mt. Lemmon at an elevation of 5,900 feet on the N.E. slope of the Catalinas. The Oracle Ridge property, formerly known as the Control Mine, is owned by Oracle Ridge Mining Partners, a joint venture between Continental Materials Corp. of Chicago and Union Miniere of Brussels, Belgium; both or¬ganizations specializing in the non-ferrous metal industry.

Jan 1, 1979

By David R. Peterson

This report presents a deep ocean mining operational simulation which is capable of describing the response of the bottom collection unit to specified mining ship maneuvers and the corresponding operation of the mining ship maneuvering system. Bathymetry, obstacles, collector and pipe dynamics and ship maneuvering capabilities are included in the simulation. The simulation is capable of evaluating the technical requirements and operating costs for specified mine plans, Results are useful in assessing mine size requirements and provide operating 'cost 'estimates useful as inputs to deep ocean mining economic feasibility assessments, The simulation is used to determine the consequences of obstacles to mining system operations in terms of impact on mine size requirements and reduced production arising from obstacle avoidance maneuvers of a towed (unsteered) collector.

Jan 1, 1979

By Gregory B. Baecher, Walter Steiner, Herbert H. Einstein

1. INTRODUCTION Empirical methods have always been important in tunneling in contrast to many other branches of engineering. Beginning in the late 19th century, when engineering entered the phase of formal modeling, this dichotomy could be seen to emerge even in the work of individuals. Culmann (1), Ritter (2) Kommerell (3) and others simultaneously were developing analytical approaches to bridge and building design and empirical approaches to tunnel design. The dichotomy remains. Empirical or simple analytical methods are used at most in the preliminary design of bridges and buildings, while they are used in all phases of tunnel design and construction. In fact, the past decade has seen a resurgence of interest in empirical methods, and with it discussion and controversy. This discussion has centered on the suitability of various methods. In some applications identical results are obtained with differing methods and in some cases radically different ones. On certain occasions the discussion has focused more on the methodological rather than empirical by taking issue with the appropriateness of particular parameters or the structure of some methods. This paper attempts to establish a basis for judging the suitability of empirical methods in tunnel design, and their applicability to particular cases. The paper makes no claim of exhaustiveness, and instead emphasizes basic requirements for application. Various methods are reviewed against this background. A detailed comparison of empirical methods and a description of their concept and background is now being prepared (4). Specifically the paper first defines empirical methods, and their purpose (Section 2), describes their structure (Section 3), and focuses on the basic requirements each must satisfy (Section 4). Then

Jan 1, 1979

By R. L. Vaughn, A. G. Moon

In 1972 a major renovation of the flotation and regrinding circuits was completed at Kennecott Copper Corporation's Chino Mines Division concentrator at Hurley, New Mexico. At that time a new lime distribution and control system was placed in operation. Lime is used to depress pyrite, and flotation at a high pH or alkalinity is required for optimum recovery of principal copper minerals, chalcopyrite and chalcocite with good rejection of the pyrite. Regrinding is also required to liberate chalcocite, much of which occurs as intimately associated chalcocite-pyrite middling grains. Accurate control of the lime addition is necessary to obtain both optimum metallurgy and minimum lime usage. At low pH levels, flotation cell control is difficult due to excess froth, but excessively high pH levels can go unnoticed because froth characteristics do not change from those experienced at the desired pH. With manual control of the lime addition, the desired pH can be exceeded for periods of up to two hours. Test Work Plant test work on a lime control system using conventional pH probes gave disappointing results with high electrode maintenance and poor control characteristics. For example, the rougher flotation cells are operated at a pH between 11.4 and 11.6 and the probes required cleaning at least once a day, and occasionally every shift. These high maintenance requirements were considered unreasonable for a plant-wide system using six or more control loops.

Jan 1, 1979

By John J. Borkert, Carl E. Gerity

In situ mining offers a new and proven method of exploiting sedimentary uranium deposits. The feasibility and economic evaluation of exploiting a uranium reserve by either open pit or underground mining should also include a similar study for in situ mining. This report compares the economics of mining several hypothetical uranium deposits at various depths, grades and reserve sizes by open pit and in situ mining. The evaluation process evolved establishing, where possible, common geological and logistical parameters to both methods of mining. The various assumptions that are unique to either open pit or in situ mining were also drafted, where possible, as equal and common functions to be used in each economic evaluation of the reserve models. After the various parameters were defined, they were programmed to an economic analysis of the various hypothetical uranium deposits by the selected mining method. From the vast array of cost evaluations, total capital and operating cost per pound U308 produced, DCF-ROI, and total net profits before State and Federal taxes were selected as the most meaningful results to compare. From the various geologic parameters used, it was determined that the economic viability of a mining venture is most sensitive to a depth-grade thickness ratio. The three selected evaluation products were plotted against the various depth-grade thickness ratios of the hypothetical uranium deposits. The results of the economic cost analyses show in situ mining generally to be a better method to maximize total net profits and to maximize return on investment.

Jan 1, 1979

By Rodney C. Espley-Jones, John C. B Wilson

South Africa is well known for its shaft sinking exploits, and many of the world's biggest and deepest shafts are to be found there. Blasting practice differs in a number of respects from that followed elsewhere.

Jan 1, 1979