Search Documents

By Kister H

Hoesch HUttenwerke AG, Dortmund, West Germany, is an integrated steel work of the Estel-group. The nominal annual production capacity-is about 7 Mio tons of steel. Hoesch has along experience in operation of diffe-rent types of slag granulation plants and of utilization of the granulated product. This experience is used to granulate a large amount of blast furnace slag and to process it in own cement plants and produce blast fur-nace cement.

Jan 1, 1979

By Kenneth K. Humphreys, R. M. Quinlan, Stan Venkatesan

INTRODUCTION 1 * The coal industry in the United States has undergone significant economic changes in recent years. For example, the price of coal remained relatively constant from 1950 to 1969 (see Figs. 5-1 and 5-2) but steam coal prices tripled and metallurgical coal prices doubled from 1969 to 1974. This price structure has created a new economic environment for coal preparation. Contributing factors to these price trends include: 1) Coal Mine Health and Safety Act of 1969. 2) Mid-East oil embargo of 1973.

Jan 1, 1979

By C. C. Hatch

As part of a general project to simulate a concentrator, the Brenda Mines Limited secondary crushing plant, located near Peachland, B. C., was sampled during the summer and winter of 1975 to develop a digital crushing plant simulator specific to the Brenda operation. The purpose of this simulator was to study the influence of manipulable process variables on important responses and to permit study of alternative circuit configurations if desired. This paper describes the simulation methodology employed and presents the results of a computer study of the secondary crushing plant (1).

Jan 1, 1979

Mr. Raden has described the practical problems associated with fines in phosphate rock beneficiation. In this discussion, a colloid chemical viewpoint is given to the problem of separating phosphate values from phosphatic clay slurries. The phosphatic clays are predominantly colloids of a complex mixture of many minerals (1). The constituents are typically 25% apatite, 40-50% clays, and various amounts of wavellite, quartz, dolomite, fluorite, and other minerals. The clays are montmorillonite, attapulgite, and illite, with some kaolinite. The various mineral colloids in the slurry are heterogeneously coagulated in the as-produced state. Dispersion of the coagulated state is evident from the fact that dispersing agents (certain polyelectrolytes) cause a large reduction in the viscosity of the slurry (2). The as-produced slurry settles from 4 to 8% solids within a week, but thereafter settles much more slowly in the form of a sediment of flocs. The supernatant liquid is often clear because of the cooperative action of the mutual interaction of particles during settling. Mineral segregation during settling has not been observed for the same reason. The initial slow settling rates indicate that the coagulated assemblies are very small. Efforts to separate apatite from the other minerals would be complicated by the heterogeneous coagulation state. Somehow the apatite must be "liberated" from its association with the other minerals before it can be physically separated. One approach for liberating apatite is to disperse the entire suspension. While this is feasible technically, for example by using certain polyelectrolytes (2), the reagent costs based on present

Jan 1, 1979

The primary goal of a maintenance information system should be to aid the maintenance department in providing the required equipment or plant availability at the lowest possible cost. To achieve this goal, the system must provide information in support of the following objectives: (1) establishing the best fleet, equipment, and component configuration; (2) establishing the best maintenance program; (3) executing the defined maintenance program efficiently; and (4) monitoring equipment availability. These objectives can be satisfied with five groups of reports. Each of these groups should provide regular, periodic reports to aid in planning and monitoring trends, exception reports to identify problems, and on-request reports to provide analytical capabilities.

Jan 1, 1979

By R. F. Janke, J. F. Bossler

Introduction The commercial use of ion exchange resins to recover uranium evolved in the decade following 1950 when significant efforts were made to recover this vital element economically and efficiently from low grade ores. It was discovered that in both acid and alkaline systems, uranium exists as an anionic complex. This led to the application of anion exchange resins to concentrate and purify the uranium product. While this is the simplest statement of what an ion exchange resin does in the recovery of uranium, it should not be forgotten that the industry is continuing to evolve new methods in mining and processing which affect ion exchange operation. The inception of solution mining, the use of expanded bed ion exchange columns and the development of continuous ion exchange systems represent several examples of this continuing evolution in the industry. Throughout all of the changes in equipment designs and variations in solution compositions, the purpose of the ion exchange resin remains the same - to concentrate and purify uranium. Ion Exchange Resins When evaluating ion exchange resins for a uranium recovery project, the task that faces the chemist or process metallurgist is an assessment of the efficiency and, therefore, the economics of the various candidate resins for a given project. This assessment should include consideration of both physical factors such as particle size, density, hydraulic expansion and pressure drop as well as chemical factors such as the uranium loading and elution characteristics. For any given application, the differences in the physical and chemical behavior of ion exchange resins are a function of the conditions used to manufacture those resins. Therefore, an understanding of the way in which manufacturing variables affect resin behavior is important. Since most uranium recovery projects are concerned with recovery of the anionic complexes of uranium using anion exchange resins, this discussion will be restricted solely to the family of anion resins. The majority of the ion exchange resins used in commercial recovery operations look similar to the resins shown in Figure #1. [ ] Most of these materials are based on a styrene- divinylbenzene copolymer. The liquid monomers, styrene and divinylbenzene, are charged to a co-polymer reactor containing water. The water insoluble monomers are then mixed with the water to suspend oil-like droplets of the monomer mixture in. the water. The entire reaction mixture is then heated causing the monomers to polymerize into sol id thermoset plastic spheres. The spherical nature of the particle, the particle size distribution and the primary crosslinking level are fixed in this step in the production process. Figure 2 is a simplified illustration of this step of the process. [ ]

Jan 1, 1979

By D. O. Tansey

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved

Jan 1, 1979

By J. C. Watts

Ball mill grinding circuit control has received increasing emphasis in the past few years due to such factors as declining ore grades, increasing production costs, and advances in analytical devices and minicomputer technology. Since ball mill circuits have been a traditional bottleneck in mineral processing plant throughput, control systems often improve through- put without requiring additional processing equipment. In addition, much of the variability of the grinding product size and consistency is often removed, allowing better process operation downstream. Among the problems which arise in designing and implementing a process control strategy for ball mill circuits are circuit constraints imposed by processing equipment and local management, proper instrument selection, installation and maintenance, and use of calculated or inferred variables for process measurements. This paper discusses these problems and attempts to identify valid approaches to their solution.

Jan 1, 1979

By R G. Richards

Although most New Zealand coals are low in ash, there are situations where high ash coals could be won. Not all high ash coals can be upgraded by physical means, since the ash is either inherent in the coal or bound in such a way to make its physical removal either impractical or uneconomic. Nevertheless, the authors believe, the situations where high amounts of ash can be economically removed by physical means to make a saleable product are considerable.

Jan 1, 1979

By Donald Ross-Watt

Mining project investment concerns the installation of mine capacity for the purpose of generating a stream of future economic benefits. In order to make this type of investment decision, the optimum specifications for the project must first be determined. Then, the economic justification of the investment tin be evaluated based on these specifications. Economic evaluation to guide mining project investment decisions is based on a proposed plan for mining the deposit over its operational life. If single point estimates are made of deposit characteristics and environmental parameters* as the basis for assessing a future stream of economic benefits associated with the investment, a future mining-plan can be optimally fitted to these estimates and, to the extent that such estimates are actually realized, this plan will retain optimality.

Jan 1, 1979

By Robert F. Winkle

A detailed breakdown of mining costs, available to management on monthly and year-to-date bases, is mandatory for a controlled and efficient mining operation. A simple lump sum reporting of costs may indicate a profit or loss differential, but it does not allow an effective search for areas of possible cost reduction. Moreover, functional reporting is necessary on a timely basis so as to note trends of increasing costs In specific areas, which in turn allow possible preventive action by management. Definitive cost information helps to eliminate the tendency to overlook areas where cost Improvements can be made. A good cost control system points out salient operational weaknesses by: ( 1 ) allowing comparison of functional costs with similar costs of other mines and (2) pinpointing sudden increases over unit empirical costs within the organization. In general, the cost accounting structure is relatively uniform within large open pit mines, but surprisingly some systems will overlook the need for detailed breakout in comparatively high cost areas. In some other systems, unrelated costs will be lumped together, preventing careful analysis of cost accrual.

Jan 1, 1979

The accurate calculation of ore reserves is one of the most important functions under- taken at a potential or operating mine. In recent years there has been a trend towards recommending more and more complex techniques for the calculation of reserves. However these are not always necessary and many improvements could be made by the use of all potential data and a heavier geological input. An ore reserve should be the result of geological not mathe- matical or engineering reasoning. All ore reserve estimates are wrong and the important thing is to.recognise why they-are wrong and to take action to minimize the errors. Geostatistics and other complex mathematical techniques may appear to answer all our needs for ore reserve accuracy but there are many drawbacks, not least of which is the communi- cation gap which may develop between the operator and both management and production Personnel.

Jan 1, 1979

By Philip Thompson

A part of the Bureau of Mines mission is to help improve the Nation's mineral posture by providing the technology for utilizing low-grade ores. In this regard, laboratory testing by the Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores that have a high content of water-insoluble impurities. Results indicated that over 82 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 by using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered 87 percent of the potash in rougher concentrates containing 57 percent K2O. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K2O. Filtration of the water-leached insoluble-slimes flotation concentrates on a bed consisting of leached insoluble-slimes concentrate mixed with potash flotation tailings recovered 80 percent of the brine. Filtration rates using the mixed bed were nine times faster than filtration rates obtained when the insoluble-slimes flotation concentrates were filtered separately.

Jan 1, 1979

By M. F. Werneke, J. A. Jones

The use of a unique class of sulfhydryl collectors, the monoalkyldithiocarbamate salts (RNHCS2M) as direct collectors for malchite and azurite is presented. Microflotation and laboratory scale flotation tests were performed to define the collector properties of these reagents under a variety of flotation conditions. On the basis of the results, it is proposed that some property of the amine-hydrogen atom in the reagent has a signification influence on the unusual activity of these collectors for oxide copper minerals.

Jan 1, 1979

By Zygmunt Wegrzyk

Poland is rich in hard and brown coal reserves, which have become the most important, and steadily developing, primary source of energy. With 192.6 mill. t of hard coal production and 40 mill. t of exports in 1978, Poland is fourth and second in the world respectively. The paper discusses the various mining methods adopted in the country's history of mining. Particular emphasis is placed on longwails, their mechanization and equipment assembled in the form of fully mechanized face complexes suited for varied geological conditions. Measures to improve the recovery ratio of coal resources are dealt with. investment efforts undertaken in the coal industry are outlined. An account is given of the ever improving techno-economic results of coal mining. The country also exports a wide range of mining equipment and transfers its well-founded technical know-how to others. There are strong cooperative links with many foreign partners.

Jan 1, 1979

By D. R. Nagaraj

Based on our finding that commercial copper chelating solvent extractants such as LIX65N® and LIX63® are excellent collectors for copper minerals, a detailed study was made using several water-soluble chelating agents belonging to the class of aromatic hydroxyoximes and having a gradual structural variation. A basic study of the system salicylaldoxime-tenorite was also carried out. Microflotation tests as a function of concentration of oxime, pH, addition of copper etc., using oxidic copper minerals such as chrysocolla and tenorite, and batch laboratory flotation tests using synthetic mixtures of quartz and oxidic copper minerals were carried out. The studies were aimed at an understanding of the collector function of the hydroxyoximes and of the general flotation behavior in these systems, in addition to studying the structural aspects of oximes vis-a-vis flotation. The results have demonstrated that all of the hydroxyoximes studied here have comparable collector property, and in all cases the oxime was found to be partitioned between the mineral surface and the copper in the bulk aqueous phase in the form of a bulk copper chelate. The occurrence of the latter could be accounted for by the formation in the bulk phase of a chelate between oxime and copper released from the mineral and/or by the detachment of the surface chelate. The role of surface and bulk chelates in flotation is discussed based on the results of partitioning of chelating agent into bulk and surface chelates in the system salicylaldoximetenorite. The effect of substitution of CH2 groups or benzene ring in the chelating agent molecule on its collector property is also discussed, in addition to the finding that only the anti-isomer has the ability to collect.

Jan 1, 1979

By John H. Canterford

The conversion of nickel and cobalt to the water-soluble sulphates forms the basis of some of the many methods of recovering these metals from their oxide and silicate ores. The applicability of these sulphation processes to a range of Australian oxidized ores is discussed. The chemical and hence mineralogical composition of the ores is shown to have a major influence on the degree of nickel and cobalt extraction. Different sulphation processes are compared, taking into account the influence of ore composition, and considering effects on reagent consumption and on subsequent metal recovery processes.

Jan 1, 1979

By David C. Oyler, Paul W. Jeran, William P. Diamond

The Bureau of Mines is cooperating with the U.S. Department of Energy in a directional degasification project at the Emerald mine near Waynesburg, Pa. This project is designed to combine the highly successful underground horizontal degasification technology with surface drilling methods. The objective of this program is to demonstrate that directional drilling can be used as a technique for degasifying coalbeds ahead of mining to reduce the hazards of methane-air explosions in coal mines. The directional hole at the Emerald mine is designed to start vertically and enter the Pittsburgh coalbed horizontally. A 3-inch-pilot hole entered the Pittsburgh coalbecl at a vertical depth of 999 feet, The hole will be reamed to 8-3/4 inches in diameter, and 5-1/2-inch casing will be cemented in place. Three individual 3-inch-diameter, 3,000-foot horizontal gas collection holes will be drilled into the coalbed in a “bird foot” pattern. A corehole and vertical dewatering hole have been completed at the anticipated coalbed intercept. The dewatering hole was drilled to130 feet below the Pittsburgh coalbed, a depth of 900 feet, and 880 feet of 7-inch-OD casing was cemented in place. Seven vertical holes for monitoring the extent and progress of degasification have been drilled within the horizontal drilling area.

Jan 1, 1979

By James R. FitzSimmons

This report describes an instrument developed by the Bureau of Mines as an improved device for examining roof rock in bolt holes. The unit consists of a commercially available fiberoptic unit adapted for use as a flexible stratascope. Field testing in both metal and coal mines has shown the instrument can be easily transported and used by a single operator. The size and flexibility of the instrument eliminate the need for specially drilled holes.

Jan 1, 1979

By E. R. Cole

The Bureau of Mines developed a procedure that enables substitution of zinc cathodes for the aluminum cathodes normally used in commercial zinc electro-winning. Using zinc cathodes eliminates the necessity for stripping and makes it possible to electrowin zinc from solutions derived from material containing excessive amounts of soluble fluorides; for example, zinc concentrates obtained as a byproduct of fluorspar mining in Kentucky and Illinois. To demonstrate the viability of using zinc cathodes, fluoride-containing zinc concentrate was roasted, leached, and purified according to current commercial practice. Electrolysis was carried out in 0.8-, 1-, 5, and 10-liter cells at 35° to 40° C with a cathode-current density of 8 amp/dm2 in a solution containing 65 g/l Zn++ and 200 g/l H2S04 using PbO2 anodes. Zinc deposits were produced on zinc cathodes with good morphology and excellent current efficiency (90 to 94 pct) in solutions containing enough fluoride (~0.5 g/l, F+) to cause sticking of zinc to aluminum cathodes. The approach described has failed previously because of severe solution-level corrosion of the zinc cathodes. The present investigation found that the use of a simple mechanical barrier to prevent oxygen migration from the anode was sufficient to prevent solution-level corrosion of the zinc cathode starting sheet.

Jan 1, 1979