Search Documents

By G. Rinelli, A. M. Marabini

A wide-ranging series of experiments has been carried out on value minerals (sphalerite, smithsonite and hematite) and gangue minerals (quartz and calcite) to assess the properties of various commercially available vegetable and synthetic tannins as dispersants for these minerals in a finely ground state (<5 microns). Experiments to determine the dispersing power of each reagents on every mineral have been performed through sedimentation tests run first in water and afterwards in the presence of a collector having specific action on the mineral concerned. The tests have been extended to a wide range of dispersant concentrations, maintaining the pH and collector concentrations at the levels known to be the best for the flotation of the various minerals. By comparing the results obtained on each mineral, conclusions have been drawn on the possibility of using different classes of vegetable and synthetic tannins in the selective flotation of fine particles. These results have been related to the structure of the tanning compounds and to the surface properties of the minerals.

Jan 1, 1980

By T. E. Smith

"This paper describes the application of a motor-driven flywheel unit, known as a peak shaver, to compensate for the cyclic load fluctuations of a large electric dragline installed at Pine Point Mines, near Great Slave Lake in the Northwest Territories. Of particular interest in this application is the fact that the power system supplying the dragline is a relatively small isolated system, with the major generating source approximately 170 miles from the mine.The cyclic load fluctuations of the dragline are theoretically capable of producing a maximum swing of up to 11 megawatts, which approaches nearly 50% of the installed generating capacity. To reduce these load fluctuations to acceptable limits various alternatives were considered, leading to a decision to install a peak shaver to optimize the operations of both the mine and the power system. Without the peak shaver, the dragline operations would be severely curtailed and additional diesel generation would have to be run at considerable expense, otherwise the power system frequency fluctuations would be totally unacceptable. With the peak shaver, power and frequency fluctuations are kept within tolerable limits, and optimum economic operation of the diesel generation is obtained.The paper outlines the steps leading to the selection of the peak shaver as the compensating device, describes the equipment installed and gives details of operating experience with the dragline/peak shaver combination since installation early in 1979. This .peak shaver is the first of its kind in North America, the only other peak shaver installation being in Australia.IntroductionPine Point Mines Limited owns zinc-lead mining and milling operations located at Pine Point, Northwest Territories, 5 miles south of Great Slave Lake (Fig. I). The company is staffed and managed by Cominco Ltd., which has a 69% interest in Pine Point Mines.Mining activity in the Pine Point area was first recorded in 1898, when the Yukon gold rush was on, but when the zinc/lead showings in the Pine Point area did not yield much in the way of gold, interest in the area soon waned. Cominco Ltd. first acquired some claims in the Pine Point area in 1928, but interest was sporadic until the early 1950s, when extensive exploration indicated rich pockets of zinc/lead ore near the surface. Pine Point Mines Limited was formed in 1951, with Cominco acquiring a majority interest in the company."

Jan 1, 1980

By H. Stocker, C. E. Makepeace

"This paper presents the statistical analyses of several sets of data acquired in several programs of sampling of radon daughters in uranium mines. The measurements were taken over periods of days or weeks for given locations or location occupations within these mines. Because the sampling applies to specific intervals of time and specific locations, a method is suggested f or the eventual application of a monitoring program which would be suitable on an annual basis for these locations. The present data and analyses thereof are not justifiably applicable to a monitoring regimen on an annualbasis, without a number of additional assumptions.The aim of the present analyses of concentration measurements is the determination of the minimum number of measurements required to achieve an annual radon daughter exposure estimate, for individual workers, having an error no greater than 50% at the 95% confidence level. The criterion of accuracy is taken from a statement in the American National Standard, Radiation Protection in Uranium Mines (ANSI NI3.8-I973), and is currently used, in somewhat modified form, as a guide to uranium mining licensees in Canada. Uncertainties associated with occupancy time are ignored in the present analysis. IntroductionOne of the principal aims of any scheme of radiation protection is that of improving the accuracy of exposure estimation for workers. The example presented here is from the area of radon daughter exposure estimation for uranium miners. The conventional means of estimating workers&apos; exposures is grab sampling of radon daughter concentrations combined with occupancy time weighting in the various work and travel locations. Uncertainties exist in each of these components, and in an environment of highly variable radon daughter concentrations (such as an active uranium mine) one is always uncertain as to the representativeness of the grab sample (compared to the average concentration) unless a sophisticated monitoring scheme has been implemented based on previous experience in such an environment.Improvements in the accuracy and precision of employee radon daughter exposure records depend, primarily, on three factors;"

Jan 1, 1980

By A. L. Hornbaker

Colorado has recorded more than 100 years of industrial mineral production. Much of the state&apos;s history, culture, and economy is based in mining, but the industrial minerals and construction materials comprising the nonmetallics sector of the industry very often are overlooked or overshadowed by mineral fuels and the metals. Indeed, many of these materials find use in seemingly unimportant industrial applications essential to our economy and life style and yet are not so recognized by the consumer. Unlike many other mineral resources, the numerous industrial minerals occur in many different and often exotic geologic environments, some of which are characteristic only of the western states. In Colorado only a few of these minerals have continued production through the years; many saw only "boom" periods or other critical times of need, such as the world wars. The changing needs and demands of our society in the 1980s will stimulate yet another era of intensive activity in our industrial minerals storehouse. Researchers are finding new uses and applications for these materials in dealing with the energy crisis and fuel shortages, the need to develop domestic mineral reserves of all kinds, and the goals of reuse and recycling. Some of Colorado&apos;s little-used and unused industrial minerals hold extraordinary promise in solving some of these problems on the regional and national levels. In this paper we will look at the history of development of Colorado&apos;s more prominent nonmetallics and especially at current research on and future potential of several other commodities among which Colorado contains the largest known reserves.

Jan 1, 1980

By Mark Sanders

This report describes an experiment which was conducted to compare the relative bumping hazard of a low and high profile hard hat (helmet) in a low seam mining environment. The study was specifically designed to assess the effect of lowering the helmet profile on frequency of head impacts in an underground low seam coal mine simulator. This involved subjects performing four common low coal mining tasks wearing the low and high profile helmets in the low seam simulator (36" and 48? heights). The results of the study indicated that a low profile helmet could reduce bumping frequency in underground low coal approximately 25%, and as much as 80% on selected tasks. It was beyond the scope of the study to measure the impact force, thus it was not possible to estimate the effect of the low profile helmet on severity of impacts underground. The research team recommended that a more extensive investigation be made of head injuries experienced in low seam mining (both underground and surface) with the objective being to assess the impact of a low profile helmet on total head accident exposure.

Jan 1, 1980

By Richard A. Brown

The direct precipitation of uranium with hydrogen peroxide has been known since 1877. Commercial use of the process began in the 1960&apos;s. During 1967 the Bureau of Mines assisted the Climax Uranium Co., Grand Junction, Colorado in the development of a uranyl peroxide precipitation process to control a molybdenum impurity problem (1). Atlas Minerals, Moab, Utah has used hydrogen peroxide to control vanadium and sodium levels in their uranium concentrates since 1969 (2). Recently, the use of hydrogen peroxide by the uranium industry has grown, particularly since the increased demand for uranium has led to the processing of low grade ores. Impurities present in low grade ores can be concentrated with the uranium during milling and will substantially complicate the refining of uranium yellowcake concentrates. Consequently, commercial nuclear fuel processors have imposed stringent specifications and penalties to control these impurities. The ability to produce a pure uranium yellowcake can eliminate penalty or reprocessing costs. Hydrogen peroxide precipitation of uranium is specific and quantitative, producing a very high purity product.

Jan 1, 1980

By P. Somasundaran

Processing of fine particles in suspension is markedly affected by their state of dispersion/aggregation. In addition, tendency for a given component of the system to undergo selective aggregation or selective dispersion is an important property which may be put to use for processing. In this paper, principles governing flocculation, dispersion, and selective flocculation of mineral fines are discussed and then the role of major solution properties such as pH, ionic strength, etc. is examined.

Jan 1, 1980

By Marc Lonoff

Byproducts are more important to the copper mining companies than to the copper market. Copper ores frequently contain gold, silver, molbydenum and cobalt. With the increase in the prices of these metals copper mining has become more profitable. If byproduct prices remain high, additional firms will be attracted to the copper industry; the increased supply of copper will reduce the long-run copper price. However, this is unlikely to happen because the markets for the copper byproducts, especially molybdenum and cobalt, are small. Increased recovery from copper and other sources will depress the prices of these byproducts before the copper price is significantly affected. Should byproduct prices remain high the copper market will both settle at a lower long-run price and be more unstable in the short run. Since changes in the copper price do not affect the entire earnings of a multi-metal mine, the copper price must fall further before such mines reduce output in the short run. Higher byproduct revenues will make copper supply less responsive to copper price; shifts in copper demand will result in greater copper price fluctuations in the short run than they did before.

Jan 1, 1980

By T. G. Carnahan

The U.S. Department of the Interior, Bureau of Mines, performed a laboratory-scale investigation of technique for recovering silver from pregnant solutions generated in the hydrometallurgical treatment of complex base-metal sulfide concentrates with oxidizing chloride media. This provides a means for recovery and simplified reduction of accessory silver to metal from ions. The method consists of adding NaI or KI to the solution to precipitate AgI, which is then contacted with Na2S to produce Ag2S and to regenerate the iodide salt solution. Silver recoveries range from 99 pct with 20 pct excess iodide precipitant, to-92 pct when the theoretical stoichiometric amount of precipitant is employed. The Ag2S product can be reduced to silver metal by contact with aluminum chips in NaOH solution followed by purification with conventional fire refining techniques.

Jan 1, 1980

By R. B. Barlow, J. A. C. Fortescue

Originally developed for use in mineral exploration, regional geochemical mapping based on stream (and lake) sediment sampling is showing broader application in other areas of the earth sciences and in environmental science. The purpose of this paper is to focus attention on the role of regional geochemical mapping in relation to geological and environmental studies. This is achieved using a descriptive equation for the chemical composition of a stream-sediment sample and then relating it to the use of successive approximations in geochemical and environmental investigations. The procedure is further qualified with reference to time and process in the formation of regional geochemical patterns. Examples are included of studies based on stream sediments related to bedrock geology, surficial geology, ecology and man&apos;s effect on the geochemistry of the environment. The range of applications of regional geochemical mapping in earth and environmental studies is outlined and some conclusions drawn regarding the future development of geochemical mapping under Canadian conditions.

Jan 1, 1980

By M. F. Bucek

This report summarizes the activities performed and the results achieved during a two-phased investigation of the technical and economic feasibility of disposing of coal mine refuse underground in active mines, Three coal regions in the United States that are most severely affected by coal refuse disposal problems are identified: southwestern Pennsylvania, southern West Virginia, southwestern West Virginia and eastern Kentucky. For each region, a conceptual mine model is presented that describes the geologic conditions, mining methods, and environmental circumstances typical of that region. The model mine that was prepared for the Kanawha Region in Southwestern West Virginia and eastern Kentucky was selected as the basis for developing alternative conceptual designs of underground disposal systems in the second phase of this investigation. Procedures used in selecting the regions and in modeling typical mines are described in Part I of the report. Part II of the report describes existing methods for stowing refuse underground, presents three alternative conceptual designs of stowing system that would be appropriate for the model mine postulated in the first phase of the study, discusses technical characteristics and environmental effects relative to the various systems, and evaluates the technical and economic feasibility of the three alternative disposal system designs. Comparisons costs among systems and with costs or surface disposal are presented.

Jan 1, 1980

By Dipak Sengupta

This study analyzes the safety, technology, and economic impact of eliminating safety fuse from metal/nonmetal mines, based on operation and manufacturer experience over the past five to ten years. If safety fuse is eliminated, blasting accidents will decrease with no technical impact except for some limited, specific applications. The economic impact will be minor for large operations, but will be significant enough for small operations that some small operations will likely close rather than change. The majority of the mines would probably change over, with the extra cost absorbed by the market. Elimination of safety fuse would have obvious impact on the two manufacturers of safety fuse; one manufacturer already produces an alternative system, and will remain unaffected; the other will be affected if they do not change their production strategy. There will be a very minor effect on the mining industry as a whole due to abolishment of safety fuse from the standpoint of employment or production.

Jan 1, 1980

By Fred Leonard

This report is principally concerned with the engineering and economic feasibility of area surface coal mining systems other than draglines. This analysis evaluates shovel/ trucks, shovel/crusher/conveyors, and shovel/rail excavation and haulage systems for an assortment of geologic environments and production rates in the Powder River Basin (PRB). Shovel/trucks, front-end loaders trucks, and shovel/crusher/conveyors were studied in a multi-seam, dipping geologic area of the Four Corners Region. The Texas lignite engineering and economic research involved bucket-wheel excavators (BWE), BWE/backhoes, and scraper/backhoe combinations for overburden and coal excavation. The PRB truck/shovel study utilized the most recent computer simulation available in both the design and cost analyses. Detailed engineering analysis, followed by in-depth operating costs (operating and depreciation), result in a complete evaluation of each mining system. Cost comparisons of the different mining systems under similar geologic and production constraints are presented in the report to illustrate the estimated capital investment and production costs per ton of coal and bank cubic yard of overburden.

Jan 1, 1980

INTRODUCTION TO STATISTICS It is necessary now to digress from the direct study of appraisal techniques to consider an important tool for the mineral appraiser. Whenever a great deal of data have been accumulated, such as might be gained through the sampling process discussed in the preceding chapter, the application of statistical methods should be considered. Statistical methods are used for descriptive purposes and for the organization and summarization of quantitative or numerical data. Descriptive statistics covers the tabulation of data, its presentation in graphical or pictorial form, and the calculation of its several descriptive measures. It is not the intent of the brief summary of statistics that will be outlined hereafter to cover the total breadth and scope of mathematical statistics. It is the intent of this and the following chapters to review a few of the statistical concepts that have the most direct bearing upon the problems involved in mineral evaluation. Should the reader desire to go more fully into statistical theory and mathematics, numerous texts and publications are available.

Jan 1, 1980

By W. C. Morgan

The Federal Surface Mining Law enacted in 1978 is now being translated into regulations which must be followed in future coal mining. Substantial change to mining procedures is required to maintain stricter air and water control while mining and to return the mined out land to equal or better use than before. These changes do not come easy; and in most cases, they create a substantial additional cost. Based on field observations and mining studies, Caterpillar has been making suggestions on the use of their types of equipment to conform to the new standards at the least cost. This paper will be a brief review of some of the overburden stripping and reclamation methods suggested by Caterpillar. A production and cost comparison of dragline, scraper/dozer and truck, loader systems in 20 to 150 ft. Overburden conditions illustrates potential cost savings using mobile equipment.

Jan 1, 1980

INTRODUCTION TO PROBABILITY THEORY The mathematical theory of probability provides the foundation for the interpretations and inferences that can be made from statistical techniques. Probability theory is a broad field of study in itself, and can only be touched on here in order to provide the necessary back- ground for a more complete understanding of statistical analysis. Probability is concerned with the outcome of random events. It had its beginnings in the theory of games of chance which were of great interest to European mathematicians during the last half of the 17th century. The outcome of a random process or experiment is defined as an event. The collection of all mathematical points associated with each event is called the sample space for an experiment. Consider a random experiment having a finite number, n, of possible outcomes, some of which have a characteristic A. What is the probability that A will result from a single

Jan 1, 1980

The treatment of steels with acid solutions for the removal of oxide products represents possibly the largest outlet for chemicals in steel processing. Organic pickling inhibitors are required to prevent base metal attack by these acids otherwis

Jan 1, 1980

By Kiran B. Chaudhuri, Michael Koch, Jorg Lema Patino

"Stricter pollution regulations together with other factors have stimulated interest in the modernization of the traditional sinter - blast-furnace lead operation. In this context, direct smelting methods have again come into prominence. Consequently, the Kivcet Lead Smelting Process, which belongs to this group, has attracted the attention of the lead producers of the world. The Kivcet Process offers the advantage that lead and zinc can be simultaneously recovered in a single furnace unit. KHD Humboldt Wedag A G, Koln, Federal Republic of Germany, has signed a contract with the Sociedad Complejo Metalurgico de Karachipampa of Bolivia for the delivery of a turn-key Kivcet plant, which is expected to be the first plant of its kind in commercial operation. This paper describes the design and expected operating data of the plant."

Jan 1, 1980

By André Gobell

"La distribution des éléments majeurs dans une séquence de roches volcaniques felsiques, la formation de Waconichi, au sud de Chibougamau, indique que les roches pyroclastiques du secteur ouest de ce segment sont chimiquement anormales si on les compare à la composition moyenne des roches volcaniques de Chibougamau: elles sont caractérisées par une teneur anormalement élevée en f er, en magnésium et en potassium et une teneur anormalement basse en sodium et en calcium; ce chimisme caractérise les encaissants des dépôts de sulfures massifs d &apos;origine volcanique.Les coulées rhyolitiques massives sous-jacentes au gite de cuivre-zinc avec or et argent de Lemoine ne montrent pas ou très peu d’altération de ce genre. Le schéma de mise en place des dépôts de sulfures massifs d&apos;origine volcanique et la nature des roches en présence permettent de croire que la zone d&apos;altération mise en évidence à l&apos;ouest de la mine Lemoine puisse être reliée à la mise en place de ce gisement d&apos;ou l&apos;im portance de tenir compte des caractères texturaux des roches lors de l&apos;interprétation de données litho géochimiques."

Jan 1, 1980

By Andrzej Frycz

The development of the theory of reliability creates more and more possibilities of its application in different domains of technics. The methods evolved to date, both theoretical analysis of the engineering systems and investigations techniques in practice can be put in use a d translated from one science to another one [1,3,7J . It needs to consider the specific of the different sciences. But it is necessary to take account of the specific characteristic of each line of science. The reliability investigations needs, justified in technical and economical viewpoint appear too in mine ventilation technics and systems. The mine ventilation system is a complex of workings and ventilation plants, which serve to supply the networks with a sufficient quantity of fresh air from the atmosphere and then carry off the vitiated air. The condition necessary for a ventilation system to perform definite task is the correctness of all its elements, that is a capability to preserve in a expected range of tolerance, the values of basic parameters. The element of a system which ceases to work correctly is called failed. The basic parameter of all elements of a ventilation system is the characteristic curve, pressure loss - air quantity relation ?p = f(Q) (1) This curve concerning the workings and ventilation stoppings is given by the formula: ?p = R Q2 (2) thus the resistance R (of the workings or stoppings) may be taken as a characteristic parameter. The course of this characteristic f(Q) will be given in a complex form in concern with fans, ejectors, air curtains. The failure of a ventilation plant or working is therefore an event, relying on a change of its characteristic, thus for a definite time the losses of the plant&apos;s or working&apos;s capability set in for the fulfilment of its function in the ventilation system. The failures are divided in viewpoint of their nature on sudden and progressive. We are in concern with the sudden failures which are characterised by a violent change of the ventilation element parameter for example a fall of roof, or silt up of the working, opening or failure of the ventilation stopping, the stand-off of the fan or ejector etc. We distinguish two kinds of failures on the viewpoint of their action on the air flow: the "opening" failure and "closure" failure. The prevalence of factors, which causes the failures is in connection with the intersection in the mine of roads of haulage, roads of underground transport of materials and lining elements, roads of people motion with airways, as also depends on the rock pressure reaction on the workings lining and plants placed there. Other factors will yet be decisive upon supply decay of fans, ejectors and curtains. The appearance of failure of the ventilation element is therefore of random nature and determines the change of the element, when it is passing from operating state to unoperate. Qualifying the ventilation system element to one of these states is easy, when the characteristic change is clear and occurs suddenly, that was assumed. The investigations conducted by Patrushev and Karnaukh [91 in concern with the ventilation stoppings resistance change in the case of their opening, had shown the possibility of resistance value change in the range of several hundreds higher.

Jan 1, 1980