Search Documents

By M. Shamsuddin

Information on total estimated uranium reserves and domestic requirements have been collected, A survey has been made on the possibilities of recovery of uranium from low grade and complex ore deposits, e.g., marine phosphorites, shales, coal, sea water, etc. In order to assess the potential for uranium recovery from uraniferous phosphorites, available thermodynamic data of uranium minerals, compounds and aqueous species have been collected. The existence of uranium complexes with chloride, fluoride, carbonate, phosphate, sulfate, etc., in ground waters have been evaluated at different pH's. There seems a great need to study the relative stability of these complexes in order to judge the applicability of solution mining technology for selective leaching of uranium from phosphorites. A typical flow-sheet demonstrating recovery of uranium from wet-process phosphoric acid has been included in this report. Some essential features of the economics of uranium recovery from uraniferous phosphorites have been briefly considered and recommendation have been made for further studies.

Jan 1, 1980

By W. D. Riley

The U.S. Department of the Interior, Bureau of Mines, has been conducting minerals recovery research in support of the nation's geothermal program since 1974. The Bureau's program of laboratory and field studies has focused on determining the materials of construction for geothermal resource recovery plants and an the recovery of mineral values from the geobrines. An analytical program has been conducted at the Avondale Research Center to determine the chemical constituents of some high- and low-salinity geobrines found in the Imperial, Valley of California. Data are reported for the early stages of brine production of femur geothermal wells--the low-salinity, medium-enthalpy brines from the East Mesa Known Geothermal Resource Area (KGRA), Mesa 6-1 and 6-2, and the high-salinity, high-enthalpy brine from the Salton Sea KGRA, Magmamax 1 and Woolsey 1. The reported results indicate the importance of the operating and engineering history, the operating parameters during sampling, and the method of sampling in order to evaluate the chemical analyses.

Jan 1, 1980

By H. Sahay

"DISCLAIMER NOTICEThe views and conclusions contained in this presentation are those of the author and should not be interpreted as necessarily representing the official policies or recommendations of the Department of Mines and Energy, Government of Newfoundland and Labrador. ABSTRACTThis paper describes the main testing procedures that should be carried out to evaluate the capacity and capability of the service brakes on the large-size diesel-electric trucks now in common use at open-pit mining operations. Brake testing programs in general are described, and then consideration is given to different techniques of service brake testing, brake performance evaluation, braking energy and typical performance characteristics.IntroductionThe first diesel-electric truck with a capacity of about 85 tons was introduced in 1963 by Unit Rig and Equipment Company of Tulsa in cooperation with General Electric Company, who successfully developed and supplied the most important component- motorized wheels. Since then, its popularity and numbers have continued to grow, and now more than 3700 such units are in operation in mines around the world. In Canada alone, their number is more than 700, including about 150 in the Province of Newfoundland and Labrador. Similarly, their size has also grown from that initial capacity of 85 tons to 350 tons.Although the introduction of the electric trucks proved to be invariably economical, their indiscriminate use was not without severe consequences. Many runaways and even fatalities occurred when the dynamic retarder failed while the truck was travelling loaded down severe grades. The service brakes in such cases proved incapable of stopping runaway trucks, mainly due to their limited capability and the fading caused by excessive heat produced during the act of braking itself. This eventually led the various governments, the open-pit operators and the manufacturers to seriously question the braking capability as well as function of both service brakes and dynamic retarders. Extensive testing"

Jan 1, 1980

By M. A. T. Cocquerel, M. G. Burcher, J. G. Eacott

"This paper is based on work carried out to examine the feasibility of increasing the smelting rate of two oil-fired calcine-charged reverberatory furnaces . Various constraints prevented physical enlargement of the furnaces and so allention turned to the use of preheated combustion air or oxygen enrichment to bring about the required increase in production. As a basis for further calculation, a furnace heat balance is determined using the smelting metallurgy and combustion data for the current operation. Various other operational data are tabulated and compared with similar data from other operating copper smelters.New heat balances are derived for various levels of combustion air preheat at the current smelting rate, and the effects of air preheat on oil consumption, combustion air and waste gas volumes are tabulated. These data are used to demonstrate the level of increased throughput which would be obtained before constraints in existing gas handling equipment are encountered.A similar exercise for oxygen enrichment is set out, with oil consumption, combustion air and waste gas volumes at various enrichment levels tabulated for the current smelting rate. These data are in turn used to demon strate the smelting rate which would be achieved at a practical level of enrichment before waste heat boiler and gas handling constraints are encountered.The energy implications for both cases are summarized."

Jan 1, 1980

By S. K. Kawatra

The paper describes a system for on-line analysis of ash in solids in coal slurries for coal cleaning operations. The system consists of two sensors: 1) gama density gauge, and 2) ash sensor. The operational characteristics of each sensor are discussed.

Jan 1, 1980

By T. T. Chen, W. Petruk

The mineralogy of the feed, concentrates and tailings from the Heath Steele mill in New Brunswick was studied in detail to determine the liberation and recoveries of the major ore minerals, and to characterize the occurrence and distribution of the trace elements. The ore milled during August 1977 contained an average of 4.34 wt % Zn, 1.25 wt % Cu, 1.64 wt % Pb and 90 gr/ton Ag. The main trace elements in the ore are silver, cadmium, indium, cobalt, antimony, bismuth, arsenic, mercury, tin and gold. Silver is carried in solid solution in tetrahedrite-tennantlte, galena, Ag-Sb sulfosalts and Pb-Bi-Sb sulfosalts. Approximately half of the silver is recovered in the lead and copper concentrates and the remainder is lost in the tailings and Zn concentrate. As the major silver-bearing minerals also contain Sb and Bi, recovering silver by ore dressing would involve recovering elements that are troublesome in extraction metallurgy. Cadmium and most of the indium and mercury occur in solid solution in sphalerite and consequently are recovered in the zinc concentrate. Some indium is also recovered in the copper concentrate in a second unidentified indium-bearing mineral. Cobalt and arsenic occur principally in arsenopyrite, cobaltite, a Co-Fe sulfarsenide, pyrite and pyrrhotite, and follow these minerals into the tailings. Recovery of the valuable element cobalt, therefore, would involve recovering the environmentally hazardous element arsenic. Most of the tin and gold report to tailings. The ore was ground to about 80% minus 270 mesh. At this grind, 71 wt % of the sphalerite, 66 wt % of the chalcopyrite and 59 wt % of the galena were liberated. Recoveries of free sphalerite, free chalcopyrite and free galena in the Zn, Cu and Pb concentrates were 85 wt %, 76 wt % and 80 wt %, respectively; recoveries of unliberated sphalerite, unliberated chalcopyrite and unliberated galena in the respective Zn, Cu and Pb concentrates were 48 wt %, 5 wt % and 7 wt %. Some of the unliberated sphalerite and chalcopyrite grains in the tailings are large and would have been liberated at a finer grind.

Jan 1, 1980

By Rudolph K. Hoagberg

Silica sands, primarily in coarse size ranges, are used to prop open fissures or voids created in the bedrock by hydraulic fracturing. This procedure increases the flow of gas or oil or other fluids through the bedrock. The sands used must meet various specifications relating to their physical and chemical characteristics; these characteristics are in turn related to the geologic provenance of the sand deposit. The Jordan Sandstone, a Cambrian formation which is exposed in Minnesota and Wisconsin, meets the specifications of a proppant sand by virtue of its depositional history and its sedimentary properties.

Jan 1, 1980

INTRODUCTION AND SCOPE This chapter is intended as a brief review of the mathematics of compound interest and of the meaning of time equivalent money. In order to make valid economic evaluations of various investment alternatives, it is important that they be analyzed on an equivalent basis, taking into account the time value of money. Compound interest has been said to be one of the eighth wonders of the world. Certainly compound interest is a fact of life in today's economy. Whenever we deal with money over time-investments, earnings, savings, loans, etc.-we are immediately confronted with the principles and effects of compound interest. In such an environment it is necessary to be able to determine time value equivalence of various sums of money received or paid at different dates. It follows that all future payments or series of payments that would repay a present sum with interest at a stated rate can be said to be equivalent with each other. Equivalence, then, is a function of the interest rate. MATHEMATICS OF COMPOUND INTEREST FACTORS In order to develop mathematical formulas for various time value equivalence of compound interest we will use symbol designations: P is Present or principal sum of money; usually refers to value at time zero. F is a single sum of money at some designated future date. R is The amount of each payment in a uniform series of equal payments made at the end of each period. n is Number of interest compounding periods (may represent annual, semiannual, quarterly, or even daily periods). i is the period compound interest rate. Figure 20-1 illustrates the increase of princi-

Jan 1, 1980

By Richard Schellinger, Ronald H. Carlson, Robert D. Norris

INTRODUCTION A very important key to the success of an in-situ leach venture is proper choice of well field chemistry, in which type and concentration of oxidant plays a significant role. For proper design of well field and plant, an engineer must be able to estimate uranium production levels and their change with time. The rate controlling step in the uranium leach process is generally acknowledged to be the oxidation step (Goddard and Brosnahan, 1980; McKnight and Anthony, 1979; Mays, 1979). Uranium head grade is very dependent upon concentration of oxidant injected into the ore zone. If oxidant levels are too low, uranium production requirements will not be met; if levels ate too high, excess oxidant will be wasted in side reactions with gangue material and leach economics will suffer. To date, no reliable laboratory technique exists for generating data easily translatable to field conditions. Empirical correlations based upon lengthy field testing have been the major tools avail- able to the design engineer to date. During the past five years, FMC has developed lab- oratory techniques for studying uranium leach chemistry under conditions simulating as closely as possible the field situation. Both agitated batch and consolidated core leach procedures have been developed. Results of FMC agitated batch studies are described in detail in a companion paper (Carlson, et. al., 1980). This paper will focus on the technique developed for leaching consolidated undisturbed core under simulated down-hole conditions. Through use of a follow-up computer model (Winkley, 1980), generated data can be translated to expected field response, thus providing the design engineer with valuable information in a relatively short period of time. CHEMISTRY In addition to uranium (+4), other oxidant-consuming species present in uranium ore are iron sulfides and carbonaceous material. Iron sulfides are usually present in concentrations far exceeding those of the other two materials and, therefore, represent the major oxidant-consuming species present in uranium sandstone ore. Previous studies (Carlson, et. al., 1980) have shown that iron sulfides exist in both Texas and Wyoming ores as a mixture of pyrite and marcasite (FeSz); furthermore, uranium mineralization (existing as uraninite) was shown to exist as a fine granular material coating or imbedded in iron sulfide crystals and sand grains (i.e. quartz and feldspars). The leach chemistry of a uranium ore body can be described by the following equations using hydrogen peroxide (Hz021 as oxidant:

Jan 1, 1980

By Knut H. Hubert

The GRATE-KILN System plant at Svappavaara, Sweden, was constructed for LKAB by Allis-Chalmers under a turnkey contract and commissioned in 1969. The plant was designed to produce iron ore pellets from magnetite concentrate at 6100 mtpd using imported fuel oil. It represented the state of the art for plants of its type at the time. Fuel rated capacity was attained within one week of start-up. Product quality, power usage, fuel consumption and machine wear were within warranty limits during sustained production thereafter. As operator skills improved and gas handling system reserve capability was utilized, the plant frequently produced acceptable product at up to 115% of design capacity. During the period 1969 to 1976, market demands increased for high-quality pellets while energy costs rose steadily. At the same time, important advances in the design of GRATE-KILN Systems were being made in other plants constructed by Allis-Chalmers.

Jan 1, 1980

By B. W. Dunning

This paper describes studies conducted by the Bureau of Mines to achieve its goal of developing methods for increased recovery and utilization of valuable constituents in a wide variety of domestic and industrial wastes, In this particular study, 36 units of obsolete electronic equipment from military aircraft were disassembled into their modular components by hand to determine materials distribution. Further modular disassembly into individual parts was used to identify metal composition. After identifying the metals in some of the more difficult to dismantle modules, similar modules were grouped together, shredded, mechanically separated, and using metal composition data from hand separation, classified along with the hand-separated materials. Although this equipment is normally classified as law-value iron-bearing aluminum, data were obtained that indicated the potential for moderately higher value classification. The electronic units were classified as to precious metals, copper, iron, and aluminum contents, and scrap values were estimated.

Jan 1, 1980

By E. M. Watkin

"Land directly disturbed by hard rock mining activities in Ontario and Quebec was surveyed in 1974 as part of a country-wide assessment, (Murray 1977). Some 15, 000 hectares, or 5 7 square miles, are listed as having been disturbed by overburden removal, waste rock and tailings deposition (Table 1) in the region. That area represents sixty-eight per cent of the total area which ha1; been disturbed by mining in central and Atlantic Canada. Assessment of disturbed areas was undertaken using LANDSAT-1 and LANDSAT-2 satellite imagery. Certain limitations of the technique were recognized but the data obtained were considered a relatively acceptable assessment of the extent of disturbed areas larger than ten hectares.Approximately ten per cent of the land disturbed by mining in the two provinces has been reclaimed to varying degrees. Indeed, this proportion is correct for the country as a whole. As pointed out by Ripley, Redmann and Maxwell (1978), some of the land was disturbed long before environmental concern 01· reclamation were ever considered. In numerous instances reclamation will remain impossible until presently active operations are closed. Nevertheless, these authors feel such figures make it clear that reclamation has not been a high priority in Canada in the past. Canada is a vast country, and there has been little pressure toward efficient use of all land space. Most mining operations occur in areas distant from the country's population centres. Under these circumstances, therefore, the pressure to reduce the environmental impact of mining is much less than in the more densely populated areas of Europe and the eastern United States, where such activity can occur in or adjacent to large metropolitan areas."

Jan 1, 1980

Workers at Anaconda Aluminum Company's primary aluminum smelter at Sebree, Ky., were back on the job December 1, after agreeing to a new 3-year contract. The old contract had expired November 15. On December 20, the Aluminum Company of America reportedly shut down a 42,000-ton-per-year potline at its Wenatchee, Wash., primary aluminum smelter and half of a 23,000-ton-per-year potline at its Vancouver, Wash., smelter as a result of a power cutback by the Bonneville Power Administration. A1 so in December, Kaiser Aluminum & Chemical Corp. reduced overall power at its Mead and Tacoma, Mash,, smelters and shut down one of eight 27,500-ton-per-year potlines at Mead. Reported shutdowns for the firms since September have amounted to 76,000 tons for Alcoa and 50,000 tons for Kaiser. Alcan Aluminum Ltd. announced plans to double the generating capacity at its Kemano hydroelectric power plant in British Columbia to 1,916 megawatts. The additional power would be equal to that required of a primary aluminum smelter with an annual capacity of 567,000 tons.

Jan 1, 1980

By Anthony W. Sparks

The Bureau of Mines conducted tests designed to compare its breathing metabolic simulator (BMS) with other methods that are currently used to evaluate the performance of respiratory protective equipment. The BMS is a commercially developed device that uses a piston cylinder to simulate breath movement. Using a propane furnace that consumes oxygen and forms CO2, the BMS also simulates the respiratory metabolism of humans. The breathing and metabolic subsystems of the BMS are described in detail in this report. Results are compared from tests that used the BMS to evaluate respiratory equipment and from tests that used human subjects for the same purpose. The BMS was also tested against a pulsatile breathing machine (PBM) previously designed by the Bureau. Both machines were used to test respiratory equipment, and the test results are compared in this report. To illustrate typical applications of the BMS, the report briefly describes how the BMS was used to test two different types of closed-circuit respiratory apparatus, and the test results are presented. This research showed that BMS test results compared more closely to the results of tests that used human subjects than did results obtained using the PBM.

Jan 1, 1980

By Dennis V. Woods, J. Duncan Crone

"In order to determine its capabilities and to aid in the interpretation of fie ld results, a scale model study and field tests were carried out on the Crone borehole pulse electromagnetic (PEM) system. The model results indicate that if a borehole passes in the vicinity of a tabular conductive body, the system will not only detect the presence of the body, but will also return information as to its conductivity-thickness product, size, altitude and position.The effect of variation of these electromagnetic and geometric factors on the shape of the response curve from a borehole PEM survey is displayed by a number of suites of scale-model response curves. These model curves can be used directly as type curves in the interpretation of field results. Field tests of a prototype PEM system provide a check on the scale-model results and also summarize the procedure of interpreting field data using the model type curves.The borehole pulse EM system can be effectively used as a follow-up geophysical instrument for locating and delineating known conductive bodies. It can also be profitably utilized as a primary geophysical exploration tool in areas of deep mineralization below the depth limit of conventional airborne and ground geophysical systems. The probed area of a diamond drill hole in these cases is increased from a 1- inch drill core to a zone extending hundreds of feet from the hole."

Jan 1, 1980

By Robert F. Brindisi

There are approximately thirty to forty operating mills in the United States which are currently producing uranium yellow cake. This figure includes a significant number of in situ and by-product operations however the conventional acid leach flowsheet depicted in Figure 1 is the most common process used by domes- tic yellow cake producers. Ground ore is leached with sulphuric acid and the solids are separated from the pregnant liquor and washed in a series of counter- current decantation thickeners. After clarification of the pregnant liquor, uranium is recovered from the solvent extraction/stripping circuit by the addition of ammonia with precipitation of ammonium diuranate, or simply yellow cake. The yellow cake precipitate is then thickened in a conventional thickener before re- porting to the dewatering/washing unit operation. De- watered solids subsequently report to thermal drying, and clarified liquor from the dewatering/washing step is recycled to the yellow cake thickener. The yellow cake dewatering/washing unit operation is generally accomplished using either a solid bowl centrifuge or a rotary vacuum drum filter. In most cases the underflow from the yellow cake thickener is pumped to the dewatering/washing unit operation at approximately fifteen to twenty percent solids. For the purpose of this discussion ammonium diuranate, the product of ammonia precipitation from a conventional acid-leach uranium mill flow sheet, as discussed earlier, will be considered. With only slight adjustment this discussion will be equally applicable to sodium diuranate or uranium perioxide precipitates and to either in situ or by-product operations where such precipitates are generated. Some of the domestic uranium mills which have selected solid bowl centrifuges instead of vacuum drum filters for the dewatering/washing unit operations are listed in Figure 2. Why have these uranium mills, as well as others not listed, chosen to use the solid bowl centrifuge for this particular application? It is simply a matter of performance, reliability and economics. In the remainder of this paper the performance, initial cost, installation cost, maintenance and power consumption of both the solid bowl centrifuge and the rotary vacuum drum filter will be com- pared. In order to provide a consistent basis for comparison the appropriate sized (centrifuge or filter) unit for the dewatering/washing of 400 to 500 pounds per hour of yellow cake solids will be considered. Such a flow will usually be generated by a typical 3,000 ton per day (acid-leach) uranium mill.

Jan 1, 1980

By L. B. Bramlett

The Archean (2.65 b.y.) aged Canning Stock at Copper Mountain, Wyoming contains an average of 20 ppm U. The North Canning and Fuller deposits occur within the enriched interior of the stock. Post-Laramide development of super gene enrichment blankets occurred in wide (25- 100 m) crushed zones. Hematite and chlorite accompany pyrite and sooty pitchblende in the mineralized zones. Reduction mechanisms proposed for deposition of pitchblende are: 1) sulfides, 2) hydrocarbons, 3) bacteria, 4) the water table, or 5) some combination of these. Abundant tar- type organics appear to have preserved the enrichment blankets from degradation. Trace element and radiometric data define target zones, but exploration models focus on favorable structure.

Jan 1, 1980

By Kukla G. T

A Seam deposit User oriented Mine Planning System (SUMPS) was developed by The Broken Hill Proprietary Company Limited (BHP) at its head office in Melbourne. It is one of the computer mine planning systems developed by the Corporate Data Processing (CDP) section of BHP. To date it has been employed in the feasibility study of four coal prospects for the BHP Group, including Gregory in central Queensland - Ham and Van Hoorn (1978). It was also used in detailed short term mine planning for Gregory. A recent application was in the feasibility study of Saxonvale, a multi seam coal deposit in New South Wales with seams up to 20 m thick. The other two applications of SUMPS were also on thick multi seam coal deposits. Development of programs for the underground sub-section of SUMPS is continuing. SUMPS was developed and implemented on mini computers with graphics and plotting peripherals. The company's philosophy towards computing is one of centralized development and project planning, with transfer of hardware and software to site once the mine becomes Operational.

Jan 1, 1980

By Bolton G. C

Experiments were conducted to access the feasibility of removing zinc from lead slag by sulfation or chlorination or both. Gaseous sulfation with sulfur dioxide and oxygen released only 50 per cent of zinc even under the most severe conditions. Sulfation with concentrated sulfuric acid by a fast-leach process released 95 per cent of zinc while pug-roasting released a maximum of 78 per cent of zinc. Chloridization with NaCi in the presence of sulfating gas released 50 per cent of zinc, while direct chlorination with chlorine gas and oxygen released 85 per cent of zinc and 100 per cent of lead in a chloride condensate containing little impurities.

Jan 1, 1980

By V. Steve Reed, Ed L. Reed

The in situ leach mining process generates a waste stream that is high in sulfates, total dissolved solids, and radium 226. During the mining phase, the volume of the waste stream is relatively low and consists primarily of the bleed stream. During the restoration phase, larger volumes of waste water are generated. These waste streams require environrnentally sound disposal. The low net evaporation rate in the Coastal Bend area precludes pond evaporation as a feasible disposal alternative. Reverse osmosis is a practical method of reducing the volume of the waste water handled, but the concentrated waste stream from the reverse osmosis unit must be disposed properly. Deep well injection into highly saline reservoirs is considered a sound method of disposing of the liquid waste generated by in situ mining in the Gulf Coast uranium district. Thirteen injection wells have been permitted to serve the disposal needs of the leach mining industry in Texas. Of these 13, 11 have actually been drilled. Seven applications are pending. The injection zones for the permitted wells range from depths of 3050 to 6200 feet. Pressure limitations imposed on these wells range from 500 psi to 1350 psi. The following criteria are used to determine the desirability of a disposal well site: 1. A minimal number of nearby, improperly plugged borings which penetrate the disposal zone; 2. Minimal crustal disturbance; 3. Sufficient salinity of the water contained in the disposal zone; 4. Protection of oil and gas producing zones; and 5. Sand of sufficient permeability and areal extent to handle the desired volume without fracturing the reservoir. 1. Improperly plugged borings: During the early part of the century, oil wells, gas wells and test holes were drilled using cable tool equipment, often with a minimum amount of surface casing. Production casing, when it was set, was often partly removed when the holes were abandoned. Thus, wells drilled prior to 1940 frequently have less than 100 feet of surface casing and either no production casing or the upper part of the production casing removed. Additionally, these holes are often plugged only with mud. The close proximity of these holes to an injection well location are a concern in that they can provide an avenue for injection-depth fluids to migrate up the bore hole and jeopardize shallower fresh water reservoirs. Usually, where there are more than 6 or 8 poorly plugged borings in a 2 1/2 mile radius of the well site, it is preferable to examine deeper zones for disposal well potential. The deeper zones are especially attractive where the borings are not in a cluster, which renders monitoring more difficult. Often, even the deeper disposal zones are penetrated by a few improperly plugged borings. When this condition arises, the potential for leakage through the borings can be addressed in the following ways. a. Demonstration that the static head in the boring is higher than the anticipated increase in bottom hole pressure generated at the boring by the disposal well. A 100 psi differential between these two pressures is recommended. The calculated increased pressure at a boring caused by injection should be refined using annual bottom hole pressure measurements in the disposal well. Figure 1 illustrates an injection pressure map which can be overlain on the oil well map to determine the anticipated increase in pressure expected at each oil, gas or abandoned hole. b. Shallow ground water monitoring. A shallow monitor well is drilled next to the boring and both pressure and quality measurements are made periodically in the shallow well. c. Disposal zone monitoring. Recently there has been a tendency for regulators to require disposal depth monitor wells instead of shallow well monitoring. We consider disposal depth monitoring to be a less effective method of monitoring because it provides only indirect evidence of potential problems. Assumptions have to be made for the unplugged borings, such as mud weight, that are not addressed by the disposal zone monitoring program. There is little improvement with this system to that discussed in "a" above. A shallow zone monitoring program, however, yields direct evidence of a developing problem with an unplugged boring. Leakage by the boring will be detected quickly by an abnormal increase in pressure in the shallow well. Quality monitoring will detect upward migration of poor quality fluids. The pressure data provide an early warning of impending leakage; the quality monitoring will detect actual fluid migration.

Jan 1, 1980