Search Documents

By R. Froidevaux

Geostatistical estimation techniques were customized to enable forecast of production figures at the Silver Bell uranium mine (Uravan District). Surface drill hole data were used to provide a block model of kriged estimators of average uranium grades. The recoverable figures, such as ore-waste ratio and ore grade, are then deduced from regressive curves previously obtained from underground information and production data. Cross-validations of the entire model were performed and were found positive.

Jan 1, 1981

By M. D. Flavel

Research programs conducted by Allis-Chalmers Corporation are showing that the most efficient energy use in crushers is achieved when the forces applied to particles undergoing breakage are increased. Laboratory bench scale tests have been developed to confirm this phenomena, which was first observed in the field using HYDROCOME crushers with automatic setting controls. A new testing machine is described and methods of maximizing such benefits are postulated. FOREWORD Allis-Chalmers Corporation was founded in Milwaukee, Wisconsin, in 1847 as the E. P. Allis Company, which had an initial interest in manufacturing components in the grinding of flour. As such, its roots were started in reducing material size, which is covered by the generic term, comminution.

Jan 1, 1981

By R. T. Torrie, J. R. Mernagh, D. B. Chambers

l, INTRODUCTION Uranium mine and mill workers are exposed to external gamma and beta radiation fields from radioactive ore. In the past the average uranium content of ores mined in the United States and Canada ranged from about 0.1% to 1.0% U308 with pockets of much higher grade ore. Holiday (1973) reported that radiation surveys in the U.S. uranium mines found mean gamma "radiation rates ranged from 0.20 to 0.70 mrem/h. Such radiation rates cause relatively insignificant exposures." Others also concluded that the external gamma radiation fields associated with uranium mining did not result in significant worker exposures (Federal Radiation Council, 1967; Simpson, S.D. [et al], 1959) Gamma exposure levels in most modern-day Canadian uranium mines are reported to be low with average annual exposures estimated to be less than 1 rem/a (Frost, S.E. [et al], 1981). However, two developments are taking place which affect the potential significance of external radiation fields in the uranium mining environment. The first development stems from the most recent system of dose limitation developed by the ICRP which is intended to limit the workers' overall risk from exposure to ionizing radiation through the adoption of a sum rule (ICRP 26, 1977) which combines external and internal radiation exposures. In the case of exposure to radon daughters the sum rule will have the effect of reducing the annual exposure limit below the recommended limit by an amount that depends on external radiation and other sources of internal exposure such as the inhalation of ore dust (ICRP 1980). The Atomic Energy Control Board of Canada (AECB) is reviewing this subject and is expected to produce its recommendations shortly. Irrespective of the form of the sum rule eventually adopted by the AECB, it is clear that the net effect of the sum rule will be a collective reduction of the individual dose limits for individual exposure pathways. The second factor is the increasing development of high grade uranium deposits in Northern Saskatchewan. Some of these ore bodies have an average ore grade of 1% to 5% U308 or greater. Since the potential external radiation fields increase in proportion to the ore grade, it is apparent that increased effort in radiation protection planning is required in order to develop safe yet workable methods for mining and milling such ores. This paper is intended to provide information which can be of assistance in the formulation and development of a mining and milling plan. The principal focus of the paper is source identification and the design of radiation protection measures to limit external gamma radiation exposure. The exposure of workers to external beta radiation fields is also discussed. The paper is organized as follows: - Section 2 deals with source characterization. - Section 3 discusses the effects of finite source size and distance (i.e. geometry effects). - Section 4 presents selected data that are useful in evaluating shielding requirements. - Section 5 discusses the potential beta radiation fields. - Section 6 discusses practical data requirements for worker exposure scenarios. - Section 7 presents a variety of work exposure calculations. - Section 8 is a summary of this paper. 2. SOURCE CHARACTERIZATION This section develops the basic formulae for estimating the fluxes and doses from external gamma radiation. The calculation of the radiation flux due to a distributed source (i.e. a linear, area or volume source) as a function of distance assumes that any distributed source can be treated as a summation of point sources. [ ] Uranium ore contains radionuclides from both the decay chains of U-238 and U-235. In this paper the radioactive daughters are assumed to be in secular equilibrium with the uranium parent. (If natural thorium were present in the ore in significant quantities, the gamma rays originating from Th-232 would have to be added to the gamma rays from the uranium series). In all, there are over 50 separate gamma rays (as well as alpha and beta particles) emitted from the U-238 and U-235 radioactive decay series (USHEW 1970). The total

Jan 1, 1981

The recent paper by Bain (1981) contains an unfortunate, and potentially misleading typographic error. On page 9, second paragraph, Bain states that, "some samples of drill core from the (Candlow) Formation ... contain up to 90 ppm gold and 2 000 ppm arsenic". The gold value should read 90 ppb. In fact, in the original version of the paper (Bain, 1980), the gold value quoted was actually 60 ppb.Bain also refers briefly to some geochemical data which is attributed to me, and which I feel require some clarification.In addition, the paper contains some factual errors relating to the occurrence of carbonate and potential host rocks to Carlin-type gold deposits in the Candlow Formation.

Jan 1, 1981

By Robert C. Salak

The era of low-seam mining with continuous haulage has been here for quite some time. Typical tonnages in companies such as Terry Glenn Coal are currently averaging 405 tonnes per shift in .8m coal. JoAnn Coal has averaged 453.6 tonnes per shift in .775m to .825m coal for the past four years. John Chaney of Chaney Coal has averaged 297 tonnes per shift in .6m to .65m coal. There are many other mines that are experiencing similar success and with maintenance costs that are averaging $.10 to $.40 per tonne. These figures have been documented and can be verified by the operators.

Jan 1, 1981

By Y. C. Kim

The results from a retrospective study are described in this gaper in which she past development drilling activities were investigated using geostatistics. The purpose of the study was to determine the amount of savings in drilling cost that could have been realized through the optimal placement of sequential drill holes using geostatistics. Out of 144 DDH's that were in place within the study area, the results showed a possible elimination of 34 DDH's without any reduction on the confidence interval of the global reserve estimates. If the incremental savings from one drilling campaign to the next were considered, however, the amount of percentage savings were even greater. Other interesting results from this study were; 1) tangible demonstration of the importance of a proper geologic delineation within the study zone, and 2) the robustness of the obtained experimental variograms from the rather early stage in development drilling.

Jan 1, 1981

By M. O. Serbousek

In 1975 the Bureau of Mines Spokane Research Center began a series of laboratory and field tests to investigate the feasibility of developing a substitute for the organic chemicals used in resin roof-bolting systems. An inorganic system, comprised of calcinated gypsum, an accelerator, and microcapsules of water was developed and patented by the Bureau in 1977. The system has several advantages including economics, non- toxicity, nonallergenic, inflammability, and is not based on petroleum products. Two roof-bolting systems utilizing inorganic cements are under development at the Spokane Research Center--a cartridge system, using the microcapsules of water and accelerator, and a slurry system, using a mix-inject method which combines dry powder cement with water for simultaneous injection into a predrilled roof-bolt hole. Several underground field tests have been conducted in eastern coal mines. Test results indicate that inorganic cartridge systems are adequately supporting mine roof in several test sections. Economic potential for the bolt systems appears favorable.

Jan 1, 1981

By Francis X. Murray

Synthetic fuels will be the first major development effort to feel the effects of a new set of opposition forces. These confrontations will not be of the same variety as those which occured in the 1970s. Instead the synfuels industry, particularly in the West, will find itself confronting a new coalition of local political, community, and state spokesmen. They will oppose synfuels because the projects will represent a threat to existing lifestyles, political structures, taxes, social life, water rights, economics, and other politically sensitive considerations. In short, they mean change -- usually dynamic, full of unknowns and always threatening. The battles themselves may be fought technically over environmental issues, law and regulations; often these will be the instruments of the opposition. The real underlying problems will likely lie much deeper. In many cases environmental groups will be enlisted as the standard bearers; however, this approach may simply reflect the fact that environmental objections are convenient or at times the only tools at hand.

Jan 1, 1981

By Victor deWolfe

INTRODUCTION The Henderson Mine, located near Empire, Colorado, utilizes a continuous panel caving system to extract ore as one of the world's major producers of molybdenum. Any mine using a caving-by-gravity technique of mining must rely on closely controlled draw of the caved ore. This control is essential to insure proper caving action, to avoid damaging load concentrations of weight and to minimize the dilution of ore with waste material. Henderson is no exception. Draw control is a major factor in all production planning, from long- range plans to short-range and day-to-day ore scheduling. Draw control is reviewed constantly and administered daily in an effort to optimize production efficiency, ore recovery, and cave management. MINING METHOD The cave at Henderson is massive, moving slowly through large panels that are 244 m (800 ft.) wide by 610 m (2,000 ft.) long. Generally two cave areas are drawn at one time. The areas under active draw vary in size but can be as large as 244 m (800 ft.) by 244 m (800 ft. ) containing 400 draw points. Each draw point contains 45,360 mt (50,000 st) on the average and takes about two and one half years to exhaust. A complete panel is worked for seven to ten years. No pillar exists between panels, but rather a buffer zone of broken ore, or "static face," is left in each panel to be drawn with the adjacent, yet-to-be-caved panel in efforts of minimizing dilution of a working area from an exhausted one. (Figure 1) Production drifts are driven on 24.4 m (80 ft.) centers through the ore body. Between the production drifts are funnel-shaped draw bells on 12.2 m (40 ft.) x 24.4 m (80 ft.) centers to receive ore from the cave. Each bell is accessed by two draw points, one from the production drift on either side, thus forming a 12.2 m (40 ft.) x 12.2 m (40 ft.) draw pattern. Extraction of the ore is by rubber-tired, 3.8 m3 (5 yd3) load-haul-dump equipment. The LHDs then tram the ore a maximum of 49 m (160 ft.) to ore passes. Cave initiation and bell development are done from the undercut drifts which are parallel to and 17 m (55 ft.) directly above the production drifts. Longhole rings are drilled and blasted from the undercut drifts to define the bells and establish the undercut for caving. (Figure 2) DRAW CONTROL Since the cave line at Henderson is constantly advancing, it is necessary to be continually initiating new cave at one end while exhausting it at the opposite end. There must exist, therefore, an angle on the ore-waste contact in the broken rock from initiation to exhaustion. The basic concept of draw control is to keep this angle as smooth and even as possible, particularly at the time of exhaustion. If this is achieved, draw points are exhausted more or less in a line, avoiding pockets of remaining ore surrounded by exhausted areas. These pockets would cause spotty ore extraction at the time of exhaustion, increasing the amount of dilution occurring while introducing the potential for significant weight problems in the production area. To arrive at the desired angle on the ore- waste contact, maximum tonnage percentages are assigned to each row of draw points increasing at 10% or 15% increments (depending on cave size and velocity of draw) working away from the cave line. The available tonnage indicated by these percentages is the maximum allowable tonnage to be extracted from each draw point until the available tonnage percent- age is increased. As the cave moves, these percentages increase for each draw point regularly. However, in general the tonnage drawn from each draw point is kept at about 50% of this allowable maximum in order to maintain adequate available tonnage in the cave to sustain production for seven months if cave initiation were to cease. This available tonnage cushion is a safeguard built into the draw control program at Henderson to accommodate fluctuations in the rate of cave advance. When draw points move past the row of 100% tonnage availability, they are drawn past the desired 50% at the same increments per row until exhausted. (Figure 3) To achieve proper draw control, the number of LHD buckets to be taken from each draw point is assigned daily. The actual buckets taken, which may at times deviate from the

Jan 1, 1981

By Howard D. Jacobs

A bulk sample of oxidized taconite taken from the western Mesabi Range was evaluated by the Bureau of Mines using the Bureau-developed selective flocculation-desliming-cationic (or anionic) flotation process. The raw ore sample containing 32.3 pct Fe was treated by both cationic and anionic flotation. Using the cationic system the concentrates averaged. 37.2 wt-pct of the feed and contained 62.8 pct Fe and 4.7 pet Si02 with an iron recovery of 72.3 pet. With the anionic system, concentrates averaged 37.7 wt-pet of the feed and contained 63.0 pct Fe and 5.3 pct 8i02 with an iron recovery of 73.5 pct. A comparison of reagent costs showed that the cationic process cost 144.1 cents per long ton of crude ore and the anionic process 178.7 cents per long ton of crude ore. Reclaimed water comprised 86 pct of the total water requirement for anionic flotation and 88 pct for cationic flotation. The ore used in this study was one of three samples representing about 3.25 billion tons of oxidized taconite containing from 32 to 36 pct feed iron. Previous study had indicated that selective flocculation-desliming-cationic flotation would produce concentrates from the other two samples of 61.7 pct Fe and 5.1 pct Si02 at 67-pct Fe recovery, and 63.5 pct Fe and 4.3 pet Si02 at 8S-pct Fe recovery. By developing a successful treatment for these ores, the Bureau has insured the availability of technology for processing an amount of raw iron ore which, by itself, would supply U.S iron needs for 50 to 75 years at expected consumption rates.

Jan 1, 1981

By P. J. Conroy, E. A. Curth

INTRODUCTION In June 1962, the first attempt at longwall mining in Illinois was initiated by Old Ben Coal Company in their No. 21 Mine. Longwalling was continued intermittently using various supports until April 1970. During this period, longwall mining techniques were used on separate occasions at six faces within Mine No. 21. However, due to various problems that developed at each location the faces were eventually terminated. The most significant problems concerned the support systems and roof conditions that were present in the mine during each attempt. Between 1965 and 1972, similar conditions were met by Freeman Coal mining Company during four attempts at longwall mining in their Orient No. 5 and Orient No. 6 mines. In 1975, the U.S. Bureau of Mines and Old Ben Coal Company entered into a cost-sharing agreement to demonstrate the application of longwall mining in Illinois. The first phase of the demonstration was to conduct a premining investigation to review previous attempts at longwall mining, perform rock mechanics tests, and establish support requirements based on the lnvestigation results. The information obtained during the demonstration at Old Ben's No. 24 has been utilized to optimize subsequent face equipment and panel geometry. Mining of the first panel began in September 1976 and was successfully completed in May 1977, and two additional panels were mined under the cooperative agreement. Currently, Old Ben Coal Company is the only longwall mining operator in Illinois. In addition to the face in Mine No. 24, five longwall faces are being operated in four other mines.

Jan 1, 1981

By D. Marotte, M. David

"A new exploration procedure is proposed for volcanogenic massive sulphide deposits of the Abitibi belt. ""Samples"" of acidic volcanic rocks (Si02 > 60%) were compiled from the literature. From the 574 samples collected, 322 were used in each of a number of experiments. Forward inclusion linear discriminant analysis performed on the untransformed geochemical data shows a general depletion in Na20 and CaO along with an enrichment in MgO for a ""proximal"" group of samples relative to a ""distal"" one. The percentage of misclassified samples reaches 20% to 30%, but test sets shows good stability.The exploration procedure was applied to the Normetal deposit, where the authors took 160 samples during the summer of 1977. It quickly leads to the definition of targets for more detailed exploration together with a good recognition of the old known deposit.IntroductionVolcanogenic massive sulphide deposits in the Abitibi belt (Quebec) are mainly found in rhyolites or acidic pyroclastics in the uppermost portion of a calc-alkaline volcanic series (Descarreaux, 1972). The deposits are thought to have formed syngenetically by the action of volcanic hydrothermal exhalations during the waning episode of a felsic volcanic cycle (De Rosen Spence, 1976). Alteration pipes of disseminated sulphides are commonly present. Metal deposition from hot springs, initiating convection cells in a submarine environment, may have been the dominant process in ore formation (De Rosen Spence, 1976)."

Jan 1, 1981

By R. B. Crookston

This paper presents the status and mining method chosen by each of the active underground oil shale projects in the united States today. Potential improvements in equipment and methods on the near-term horizon are discussed. The problems and potentials that lie in the long-term future of oil shale mining are examined in light of the demands which must be met by this developing technology.

Jan 1, 1981

By Edwin R. Phelps, Charles W. Porterfield

BACKGROUND OF SURFACE MINING Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal mere mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-pear periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to increase. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu pd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu pd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining. 4) Surface mining normally recovers a much higher percentage of the coal reserve than can recovered by underground mining. 5) Some coal measures call best be extracted by surface mining

Jan 1, 1981

By G. Knight

In most mines the major contribution to the dust exposure of miners arises from rock hand- ling. Scooptrams are frequently used and produce 8 to 1300 mg of respirable dust for each ton of ore loaded. It is shown that sprays at drawpoints are not fully effective in wetting the rock and suggestions for improved wetting techniques are given. Techniques for improved dust control by ventilation and local filtration are described. The problem of dust from ore- passes and dumps on tramming levels are outlined.

Jan 1, 1981

By Michael Stanwood

Project feasibility no longer involves just technical and economic viability-today's feasibility study must include environmental, regulatory, and political considerations as well. While the US now appears at least somewhat committed to developing synthetic fuels, including oil shale, it is the environmental issues, rules, regulations, and guidelines that will play the major role in determining the timing, magnitude, and overall scope of synfuel development in the coming years. The key environmental obstacle affecting oil shale development is uncertainty. Although oil shale may be the most environmentally studied "new" technology in the world, little is known with much degree of certainty about potential environmental consequences of one full-scale commercial facility, or the effects of a massive development effort in a relatively pristine and sparsely populated area. Other primary environmental uncertainties include: • Environmental compliance costs and their effects on investment decisions; • The reliability and acceptability of anticipated pollution control technologies; and • The confusing, time-consuming environmental regulatory framework, which requires more than 100 permits, clearances, and reviews before development occurs. This discussion will focus on the latter uncertainty, and will describe he current status of potential constraints to oil shale industry development in five areas: water availability; water quality degradation; air quality degradation; reclamation and spent shale disposal; and community impacts.

Jan 1, 1981

By James R. Yancik

Economical and environmental pressures necessitates the recovery of the minus 0.6 mm x 0 coal generated by todays mining machines. This size fraction, dependent on the type of production unit, maintenance of the production unit, and the Hardgrove Grindability Index, can be a substantial portion of the Preparation Plant feed. Historically, dewatering of the collected 0.6 mm x 0 product has often been rather expensive and marginal with respect to surface moisture reduction. The Freeman United Crown II Preparation Plant more than adequately demonstrates that the continuous scroll type centrifuge can dewater 0.6 mm x 0 coal to acceptable surface moisture levels.

Jan 1, 1981

By Jed H. Mosgrove

One of the most interesting of all the subjects required of persons studying the different facets of coal mining is coal mine gases. Some mine gases have been a real problem since the very beginning of underground mining, and in the early days there was insufficient knowledge to cope with them. The history of mining shows that until about the last 50 years, much work was done primarily by the hand methods which are primitive by today's standards. Miners had to contend with gases without the aid of enclosed lighting, permissible mine machinery, sophisticated testing devices, and high-pressure ventilating fans. In early days the miners were not educated about the different mine gases nor did they have the technical equipment to determine the actual composition of the deadly atmospheres they encountered. They simply applied a descriptive term to each gas or mixture of gases depending on its effect on a person or the surrounding atmosphere. The gases or mixtures of gases were then referred to as "damps," a term which was probably derived from the German word "dampf," meaning vapors or gases. The more common damps encountered were : Blackdamp A condition of the atmosphere in which a miner's light would be extinguished and in which breathing would be difficult, sometimes even resulting in suffocation. An atmosphere deficient in oxygen which could contain a combination of any of the mine gases. Firedamp A flammable mixture of methane and air which would either burn or explode when ignited. White Damp A mixture of gases containing carbon monoxide, most often found in mines during fires or after explosions.

Jan 1, 1981

DeLamar, the largest silver mine in the United States outside the Coeur d’Alene District in Idaho, came into production in April 1977. It is a joint venture of Earth Resources Company and Canadian Superior Oil Co., with Earth Resources being the operator. The property is a consolidation of several old operations dating back to the 1800s; the better known of these are the DeLamar and Sommer-camp mines. DeLamar is situated in southwestern Idaho near the Oregon border in the Owyhee Mountains, 88 km (55 miles) southwest of Boise, Idaho. Heavy snowfalls and very low temperatures are common in the wintertime. Planned production was 77,500 kg (2.5, million oz) of silver and 5 13 kg (16,500 oz) of gold per year. Expected life at a milling rate of 1,540 mtpd (1,700 stpd) was 20 years, with an ore grade of 144 g Ag and 1.58 g Au per mt (4.2 oz Ag and 0.046 oz Au per st). Present production is at the rate of 1,900 mtpd (2,100 .stpd). The total cost to bring the mine into production was reported to be approximately $22 million, and the mill was reported to have cost about $10,000 per daily ton of design capacity. At DeLamar, naurnanite (Ag2Se) is the principal silver .mineral occurring with acanthite (Ag2S) disseminated through quartz veins and a silicified rhyolitic ash-flow tuff of Miocene age. The mineralization is relatively iron and manganese free and is readily amenable to cyanidation giving recoveries of 85% silver and 92% gold, which occurs free. When the plant was started, considerable difficulties were encountered in handling the wet sticky ore because of the high clay content. Following primary crushing, the ore is stockpiled. Due to the sticky nature of the ore, the vibrating feeders initially installed under the stockpile were replaced by a reclaim hopper and an apron feeder which was fed 24 hours a day by a front-end loader. The minus 200 mm (8 in.) ore is fed to a 5.5 m by 2.75 m (18 ft by 9 ft) autogenous mill followed by a 2.75 m by 4.57 m (9 ft by 15 ft) ball mill and cyclones. The mills are equipped with 750 kw and 520 kw (1,000 hp and 700 hp) motors. Both mills discharge to the same cyclone feed sump and a portion of the cyclone underflow is returned to the autogenous mill. Cyclone overflow, which is 20% plus 74 microns (200 mesh), is leached in four agitators in series for 72 hours (45 hours at the 2,100

Jan 1, 1981

By P. R. ZETTWOOG

HISTORICAL BACKGROUND A program in France to develop personal [a] dosimeters has been initiated 1974. The patent on which is based the present device was obtained in 1972 * . From 1972 to 1974, the possibilities of applying certain ionograph track detectors to the spectrodosimetry of radon daughters was explored. The first prototype were produced in 1974. It took four years (from 1974 to 1978) to produce an autonomous dosimeter whose components has a sufficient life span, especially for the turbine motor unit. Qualification in the laboratory was obtained in 1977. In 1978 it was obtained in the mine for technology (autonomy of 12 hours and a life span of more than one year) and in 1980 for monitoring. 300 dosimeters have been tested in underground mines all together. Indispensable peripheral equipment were also developed from 1976 to 1980 : calibration devices, equipment to prepare and develop the films, read out systems. The concept of an "Integrated System of Individual Dosimetry" (ISID) based on a personal [a] dosimeter measuring exposure to radon daughters, thoron daughters, ore dust and external irradiation doses was proposed at the end of 1980. Since January 1st 1981, ISID is used on a routine basis in some french mines, situated in remote area, and appears to be very competitive with the ambiant dosimetry. The latest version of the dosimeter is produced in mass series since June 1981 and should equip all french mines in 1982. DESCRIPTION OF THE INSTRUMENTATION DEVELOPMENT OF THE DOSIMETER MEASURING HEAD The measuring head is based on the use of ionographic film to detect a tracks. In fact, the measuring head is a spectrodosimeter which measures separately over the period of exposure: - the potential [a] energy inhaled due to the decay of Po 218, Po 214, and Po 212 ; - the number of Rn 222 atoms inhaled ; - the inhaled total [a] activity of the five long-lived emitters present in the ore dust. The contribution to the total inhalable potential [a] energy of these various radionuclidesin a typical underground mine is studied in Appendix I. The measuring head described in detail in Appendix II, is able to satisfy all the implications made in the ICRP recommendations. Appendix III deals with the use of this measuring head in the cases where the equilibrium factor is lower than 0.1. This situation occur in open-pit mines where account must be taken of the Rn 222 contribution, which is no longer negligible in relation to that of its daughters. CURRENT DOSIMETER PERFORMANCES Table I shows the characteristics of the latest dosimeter. Appendix IV should be consulted concerning qualification of the dosimeter in the laboratory and in mines, technological development which finally produced the [a] dosimeter and its peripheral equipment, and technical presentation of the ISID (Integrated System of Individual Dosimetry) based on the concept of a multirisk personal dosimeter. Data on the installation and operating costs of such a dosimeter, which would seem to be competitive, are also given in this Appendix. ADVANTAGES OF PERSONAL DOSIMETRY AS COMPARED TO AREA MONITORING The results of the first eight months of experiments carried out under real conditions in an underground mine site are given in detail in reference 8. Area monitoring : The monthly exposure per worker to inhaled Rn 222 was determined from the knowledge of time spent in various areas of the mine and for the different mining operations, as well as from numerous and systematic sampling of the Rn 222 concentration in all work places. Personal dosimetry : The exposure to potential energy from radon daughters was measured by an [a] dosimeter developed by the CEA and worn by each of the 160 miners during eight months. In this way 160 x 8 pairs of monthly individual exposure values have been obtained which can be statistically studied. This test was decisive for us because it proved that the [a] dosimeter was technically sound (very few defects over one year for 160 dosimeters) and especially that personal monitoring devices were superior to area monitoring devices. The following conclusions can be drawn 1. The exposure distribution obtained by personal dosimetry is log-normal. This is true for the results on the whole as well as for groups of results relating to certain explanatory variables. See fig. la, 1b, 1c. 2. The exposure distribution obtained by area monitoring does not correspond to any type of distribution. If the results of personal monitoring are taken as a reference, area monitoring tends to underestimate the high exposures and overestimate the low exposures.See fig. 2. 3. [a]-energy exposures are underestimated when calculated from radon exposures and the equilibrium factor found in the considered mines. This is due to episodes or to zones of high radon concentrations not registered

Jan 1, 1981