Search Documents

By Robert M. Mann

The Ag/S specific ion electrode has been evaluated for analysis of both free and total cyanide. Metal cyanide solutions were prepared from reagent grade compounds and by stoichiometric fixture of the metal with a potassium cyanide solution. Solutions containing Cu+1, Ni+2, Fe+2, Fe+3 and Zn+2 complexes were analyzed prior to and following EDTA pre treatment. This effort provides an understanding of the effect of each metal cyanide complex on the SIE analysis of free and "total" cyanide.

Jan 1, 1981

By W. R. Bush

Radiation protection in uranium mines and nuclear reactors is compared, with the objective of determining if any radiation protection practices which have worked well in one area can be adapted to the other area, especially from reactors to mines since radiation protection is more highly developed in reactors. Several areas are identified where improvements can be made in radiation protection in mines, the most important being improvement in ventilation at the workplace, greater attention to special monitoring during upset conditions, and a need for a substantial increase in radiation protection staff. It is concluded that, although considerable room exists for improvement, the general approach to radiation protection presently being followed seems appropriate for the circumstances encountered in mining.

Jan 1, 1981

By Raymond E. Kary, John W. Mcklveen

The four unit Cholla coal fired power station at Joseph City, Arizona, consumes coal from the McKinley mine located in western New Mexico. Since coals may contain relatively high uranium or thorium concentrations and may release quantities of detrimental progeny of these elements to the environs, there is concern that releases may pose an adverse environmental impact or even a health hazard to the workers. Thus, an effort was made to quantify the radionuclide content of the coal and compare the results with radionuclide concentrations already present in the vicinity of the plant. Additionally an attempt was made to assess any potential for significant enhancement of the levels of radioactivity in the environment or to plant personnel. Background gamma radiation measurements at and near the plant ranged from 8 to 12 [µ]R/hr (70 to 105 mR/yr) with a few localized anomolies measuring to 18 [u]R/hr (160 mR/yr). Levels on top of the coal storage piles decreased to ~ 6.5 [u]R/hr (60 mR/yr). Apparently the direct radiation emitted from the coal is less than the background levels in the vicinity of the plant. Measurements performed on top of several coal seams at the mine confirmed low radiation levels emanating from coal, but readings more than doubled when the overburden was monitored. Laboratory gamma spectrometry confirmed the lower amounts of natural radioactivity in the coal when compared against soil and water samples obtained in the vicinity of the plant and the overburden at the mine. In an effort to see if there is biological enhancement, animal feces was sampled. The radiation variations were found to be influenced primarily by naturally occurring potassium-40 which varied from ~ 1 to 18 pCi/gm rather than fluctuations in the uranium and thorium series. The potassium-40 concentrated in the ash were similar to the concentrations in the environs around the disposal ponds while Radium-226 concentrated in the fly ash was ~ 3 times that found in the immediate surroundings. Radon-222 gas concentrations in buildings at or near the plant ranged from 0.5 to 1.8 pCi/l and were generally lower than indoor concentrations measured in the Phoenix area. The burning of coal at the Cholla station does not appear to increase ambient levels of radioactivity found in the surrounding environs or to the workers. However, the use of byproduct fly ash for construction purposes may need to be examined.

Jan 1, 1981

By Peter J. Rafferty, Friedrich Steinhäusler

INTRODUCTION The Nuclear Energy Agency plays an active role in promoting international cooperation among its member countries in the field of nuclear energy. In addition to various other functions, it plays a major role in encouraging harmonisation of government regulatory policies and practices, promoting exchange of information, and coordination of research and development in the field of radiological health and safety associated with nuclear fuel cycle activities. The work of the Agency is carried out through a number of specialised standing committees. In particular, the Committee on Radiation Protection and Public Health (CRPPH) is responsible for the Agency's activities concerned with radiological protection and related environmental problems. Its functions include review and discussion of national radiation protection policies and practices, review of developments in radiological protection, interpretation of ICRP recommendations and the study of the means of their translation into practical applications, including the establishment of radiological protection standards. Its functions also include the preparation of technical studies and reviews on specific problems requiring attention, and coordination of further research and development at the international level. Major attention is presently being given to the NEA programme of work on problems associated with radiation protection and environmental impact of nuclear fuel cycle activities, with particular attention to the front-end (uranium mining and milling) and the back-end (waste management) of the fuel cycle. In this context, the increasing attention that has been given in several countries to the problems associated with the exposure of man to radon, thoron and their daughters, and with their dosimetry and measurement, were readily appreciated by NEA, which began an active programme of work in this field in 1976. Because of the detrimental health effects,as demonstrated by epidemiological studies,caused by prolonged exposure to excessive levels of shortlived daughters of radon, particularly in poorly ventilated underground mines, the bulk of attention and needed effort has been focussed on radon and radon daughters in uranium mining. In certain countries some concern has been expressed also about the significant levels of exposure experienced by workers in non-uranium mines,and members of the public who live in particular areas or in dwellings built with particular materials which produce higher than average levels of radon and radon daughters. However, at the time of the first NEA involvement in this field it was considered that one of the most urgent problems to be solved was that of ensuring adequate personal dosimetry for uranium miners. Consequently, the NEA was urged to organise a specialist meeting on personal dosimetry and area monitoring for radon and radon daughters to provide an international forum for exchanging information and reviewing problems in this field. The meeting was held in Elliot Lake, Canada, in October 1976. A second specialist meeting, on the same subject, was held in Paris, in November 1978, to review further developments in this area. These meetings demonstrated that the overall problem associated with exposure to radon and radon daughters had many facets, each of which in recent years has been the subject of considerable attention in many countries for different reasons. It emerged from the meetings that further work was required on a variety of issues in two main areas: 1) dosimetry 2) metrology and monitoring. Conclusions and recommendations which emerged from the two NEA specialist meetings were discussed by the CRPPH. As a consequence the Committee approved, in September 1979, a detailed programme of work in the area of dosimetry and monitoring of radon, thoron and their daughters, and approved the setting up of an international Group of Experts on Radon Dosimetry and Monitoring to undertake the work. The work has been divided into two phases - phase I, on dosimetric aspects, and phase II, on metrology and monitoring aspects. The terms of reference of the work are given in Appendix 1. A list of national representatives on the Group of Experts on Radon Dosimetry and Monitoring is given in Appendix 2; many of these persons are participating here in the Conference. The Group of Experts met for the first time in April 1980 and met again in September 1981. The work of phase I is nearing completion and a report is expected to be submitted soon to the CRPPH for its consideration. Three technical papers providing interim information on the study appear elsewhere in the proceedings of this Conference. The papers cover the three principle areas examined in the study so far: 1) dosimetric aspects 2) review of the "working level" 3) review of objectives and requirements for measurement and monitoring of radon, thoron and daughters. The authors, their affiliations, and the titles of these papers are listed in Appendix 3. A brief overview follows giving the principal results.

Jan 1, 1981

By Erland A. Tillman

The U.S. National Committee on Tunneling Technology under the aegis of the National Academy of Sciences has long recognized that productivity in major underground construction projects could be increased through better contracting practices and better management. Between 1974 and 1978, this Committee has prepared three reports on these subjects. This paper reviews these reports and their recommendations. It covers the extensive actions by the U.S. National Committee on Tunneling Technology to bring the recommendations to the attention of leaders in the underground construction industry and thus further their adoption and implementation. These activities are continuing. Visibility in this session will give these reports and recommendations increased exposure.

Jan 1, 1981

By Charles H. Arnold

This topic addresses historic and current techniques of excavating, supporting and lining tunnels of 4 m (13.1 ft) and smaller. Special considerations relate to the economics of working in close quarters and the sizes of tunnel which achieve the required facility in the optimum economic manner are discussed. The excavation discussion includes TBM, conventional and special techniques for hard rock, soft ground, subaqueous, free and compressed air tunnels. Internal and external support methods discusses timbering, steel ribs, bolting, strapping, shotcreting, grouting, and freezing. Lining methods include cast-in-place concrete, concrete pipe, segmented linings, shotcrete, and others.

Jan 1, 1981

By Bradley C. Bockrath

Some thirty coals were evaluated for liquefaction activity under a mixture of CO and H2 at 425° C. The viscosity of the liquid products was taken as an indicator of the degree of liquefaction. It was found that the direct liquefaction of a particular coal may be beneficially influenced by the presence of pyrite. Active pyrites are often found in the native mineral matter of the coal itself. For example, subbituminous and bituminous coals and lignites of relatively high pyrite content were found to liquefy more readily than similar coals or lignites which were poor in pyrite. The reactivity of inactive coals could be improved by using blends with active, pyrite-rich coals. In addition, pyrite was effective when added separately as pyrite concentrates obtained from coal beneficiation operations. Various other iron- and sulfur-bearing additives were also effective when used in combination as added slurry-phase catalysts, including iron oxides and mineral residues derived from liquefaction of active coals. Under liquefaction conditions, pyrrhotite ( Fe I- x5) is formed from pyrite or from the iron oxides and many sulfur containing species. Pyrrhotite was shown to be a hydrogenation/dehydrogenation catalyst for tetralin but is not active for initiating a variety of free radical reactions that do occur when pyrite is heated with tetralin. The role of pyrite in coal liquefaction is complex and still not well understood.

Jan 1, 1981

By W. K. Hartley

INTRODUCTION AND HISTORY The Kimberley Division of De Beers Consolidated Mines Limited includes four underground mines in Kimberley viz. Dutoitspan, Bultfontein, De Beers and Wesselton Mine and two outside mines, viz. Finsch, an opencast operation and Koffie- fontein, an underground operation. Figure 1 is a map of the Kimberley district showing the location of these mines. Finsch is 150km west of Kimberley and Koffiefontein is 80km south of Kimberley. The head office of the De Beers Company is in Kimberley. The diamond sorting and trading companies for diamonds produced in South Africa are also in Kimberley. Diamonds were first discovered in the Kimberley area at Hopetown in 1866 on the banks of the Orange River. This, and later finds, triggered the start of the great "Diamond Rush". In 1870 the Jagersfontein (now closed) and Dutoitspan pipes were discovered, followed by those at Bultfontein, De Beers and Kimberley Mine (now closed) in 1871, Koffiefontein in 1880 and Wesselton in 1891. Finsch Mine was a more recent discovery in 1961. Finsch, due to go underground in 1986, and Koffiefontein, are fully self-contained with their own treatment plants, housing, services etc. The four Kimberley mines deliver ore by conveyor to a central treatment plant and use joint ser- vices. ,+lining is presently carried out mainly by Block Caving which has replaced the earlier Chambering method. De Beers Mine, on a limited scale, and Wesselton Mine have recently started to use Sub-Level Caving, and both Bultfontein and Du- toitspan are scheduled to use the same method at a later date. The combined ore tonnage produced by the Kimberley Mines is 17 400 tons per day, Koffiefontein 12 000 tons per day and Finsch Mine 17 000 tons per day. THE EVOLUTION OF MINING METHODS Initially, the open-cast mining was carried out to as great a depth as safety would permit. In the early stages of open-cast mining, the Kimberlite was removed in horizontal slices from levels 13m to 20m apart. The rock broken in the workings was raised to the surface by means of endless rope haulage inclines. As lower levels were attained these rope haulages were replaced by aerial hoists, inclined shaft haulages or inclined skip-ways. These methods were dependent upon the strength of the unsupported pipe walls, which became increasingly unstable with depth and a system was adopted whereby the ground mined in open excavations was tipped down passes to tunnels connecting with vertical hoisting shafts sunk in the country rock. As work in the open pit became more and more impracticable due to extensive falls of ground, this system was replaced by a combination of open-cast and underground mining, and eventually by wholly underground methods. Chambering With the advent of underground mining, a system known as "Chambering" (or "Inclined Chambering") was evolved. It was essentially a combination of shrinkage stoping and caving, whereby advantage was taken of the high pressure exerted by the loose rock that had accumulated in the open excavations due to the collapse of the pipe walls. This mining method was introduced around 1890 and was successfully employed, with little change, up to the early nineteen seventies. In this system each mine was served by a main hoisting shaft situated about 300m in the country rock. Main haulage cross cuts were driven from the shaft to the pipe at 200m (600ft) vertical intervals. A sub-vertical shaft, situated close to the pipe provided access to the working levels. Chamber levels were established from the sub-vertical shaft at 13m (40ft) intervals. See figure 2. On each of these levels successive 6,8m wide “cuts" were mined out across the pipe, from one rock contact to the other, and extended vertically to the footwall of the level above. Every 6,8m cut was made up of a chamber and a "back-pillart1, each approximately 3,401 wide. The chamber was mined by overhand shrinkage stoping. The levels were carried "en echelon", with each chamber on a level approximately three cuts ahead of the chamber on the level

Jan 1, 1981

By Stephen E. Merritt, John W. Straton, T. Carl Shelton

Surveying and mapping are used to locate and visually portray objects, lines, or areas in relation to a reference point or line. The actual making of the measurements to locate the objects and points falls under surveying while mapping is concerned with putting the survey information into a graphical form. Generally, the type or class of proposed survey depends on the precision required. Some surveys may need only approximate measurements which can be obtained by simply pacing or by using an ordinary measuring tape; others may require much accuracy, thus calling for the use of an engineer's transit or theodolite along with a graduated steel tape for horizontal measurements, or a level and a graduated rod for measuring vertical distances. Mapping is likewise dependent on accuracy requirements. For example, a general layout showing the relative position of surface facilities may not call for a large scale of dimension or great precision whereas for detailed work, a large scale plus care in plotting points and drawing lines and curves are important factors. SURVEYING METHODS There are many kinds or types of surveying methods. Some examples include : land surveying for determining boundaries of land areas ; route surveying for locating roads, highways, right-of-ways, and haulways; city surveying for laying out lots, streets, and alleys; and mining surveying for projecting mine openings and locating mining operations. See Fig. 1. There are other types of surveying than those named, but in general, the type of method to be used will depend on the purpose for which the survey is to be made.

Jan 1, 1981

By Wilson A. F

The use of stable isotopic measurements as a technique for elucidating the origin and history of the water in hydrothermal fluids is relatively new. Recept studies have emphasized the importance of meteoric water in the formation of many hydrothermal ore deposits including many epithermal gold-base metal deposits which occur in faulted volcanic terrane. Other vein-type gold ores are believed to have formed from fluids of magmatic or metamorphic origin and exhibit characteristic d18O values. Preliminary oxygen and carbon isotopic data for some important gold deposits of eastern Australia have emphasized the diverse origins of their ore fluids.The Mount Morgan gold-copper orebody is shown to be of the volcanogenic massive sulphide type with ore fluids predominantly of sea water origin. The Charters Towers fissure veins formed during hydrothermal activity associated with intrusion of Lolworth Igneous Complex equivalents. Oxygen isotopic studies of the quartz reefs at Stawell and Gympie have been inconclusive. The ore fluids have a d18O value of about 7 per mil and may be of magmatic or metamorphic derivation.

Jan 1, 1981

By Robert Stefanko

Longwall mining which has a long history abroad, was used only on a limited scale in the United States until less than 20 years ago. Modern longwall mining in this country can be said to have begun in 1960 with the first installation of self-advancing props in a coal mine in southern West Virginia. In Europe, because of adverse natural conditions, longwall mining is frequently the only practical method, but, in the United States, the system has had to compete economically with highly productive room-and-pillar systems. However, because it is inherently continuous, it has greater productive potential than room-and-pillar systems, and, therefore, although only about 5% of the total U.S. underground production today is the result of the longwall system, its growth potential is great. As mining, by necessity, progresses deeper and must be done under poorer natural conditions, less opportunity will exist for the room- and-pillar system, and the longwall system will have to be used.

Jan 1, 1981

By J. Sanko

When faced with the task of designing a process control system the control engineer must consider the following: 1. The type of process to be controlled and the manner in which the process must be controlled (the algorithm). 2. The type of equipment to be used to implement the control system. 3. A means of describing the control system for use in the following areas: a. Project engineering. b. Procurement of the control system equipment. c. Plant startup. d. Operator training and reference.

Jan 1, 1981

By T. N. Andersen

The history of gold and silver analyses shows an interesting duality. On one hand, classical chemical and instrumental methods have evolved to meet changing needs, but on the other hand, the age-old and somewhat empirical fire assay has remained a popular tool. Inasmuch as gold and silver generally have been present in ores at low concentra¬tions, methods have been challenged by a need for sensitivity and selectivity coupled with reasonable assay time. A progressive increase in the importance of low grade materials as ore sources has led to the need for improved methods. Assays of these materials are required for process control and accounting in operating plants as well as for guiding research and development activities. The analytical response to these needs is evidenced by numerous reviews published through 1977-¬e.g., cf Kolthoff and Elving (1966), Beamish and Van Loon (1966, 1972, and 1977), Young (1971) , Mallett (1970), and Sen Gupta (1973). In this paper we present a brief sketch of the history and status of various gold and silver methods. A more detailed summary of atomic absorption spectroscopy (AAS) is Given, as this method has gained in popularity more than other assay methods. AAS methods currently in use are summarized and discussed briefly. This paper is not meant to be a detailed review, as are the above mentioned publications. Rather, we borrow from those works and more recent papers to report trends in gold and silver analyses (particularly in AAS). Also, we discuss some selected poten¬tial problems, and problems that have been experienced by this laboratory.

Jan 1, 1981

The explosion at Appin Colliery on July 24th, 1979, demonstrated the need for a large scale facility to simulate an underground type explosion and study its effects. The effects of an explosion cannot be established quantitat- ively using small scale models. A gallery was constructed for this purpose at Londonderry Centre and commissioned in Feb- ruary, 1980. It is 50 metres long, 2.7 metres in diameter, capable of withstanding an internal pressure of 210 kPa and is the only facility available for this purpose in Australia. The gallery has provided valuable inform- ation on blast effects of explosions in tunnels and is to be used for testing the performance of explosion arresting devices, further invest- igation of explosion effects, research into basic explosion phenomena and instrumentation development. Additionally, it will provide a demonstration facility for training purposes.

Jan 1, 1981

By Earle Faig

Along with other transportation modes, the barge industry will be greatly effected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events have caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of our long experience in moving large quantifies of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to the barging industry. Barge companies operate on a 40.23-Mm (25 000 mile) river system which includes the East and West Coasts and the Mississippi River System. Included in the Mississippi River System are the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior - Tombigbee and Mobile Rivers as well as some smaller tributaries. The Gulf Intracoastal Waterway, which stretches along the Gulf Coast from Brownsville, Texas to Apalachicola, Florida, is also considered part of the inland waterway system.

Jan 1, 1981

By P R. Denize, V S. Wein

A brief review of the Waipipi Iron Sands Limited company history and operations over the past ten years is made along with a summary of the benefits of this mining company to New Zealand. Land rehabilitation procedures in coastal dune lands are described in detail and brief mention is made of a study of animal health and copper uptake. The paper concludes with a summary of the increased emphasis on agronomy and restoration as the mining operation commences dredging in a better class of grazing land.

Jan 1, 1981

By Norman E. Lehman

Pyrometasomalic mineralization occurs within meta-morphosed Paleozoic carbonates intruded by Laramide granodiorites. Two types of alteration developed shams in the district. The dominant type is post-magmatic which developed an early hydrous endoskarn phase, and intermediate anhydrous exoskarn phase, and a late hydrous phase affecting both sham types. A rare, second type is magmatic in age, lacks the hydrous phases, and developed a mineralogically-zoned endoskarn. Garnet exoskarns lacking associated plutonic rocks are stratigraphically controlled and contain an early anhydrous phase, an intermediate hydroxyl-bearing phase, and a late hydrous phase associated with base metal deposition.

Jan 1, 1981

By George W. Toth

In a recently completed research project for the U.S. Bureau of Mines - Twin Cities Research Center, a computerized costing procedure for uranium in situ leach mining was developed by the NUS Corporation. This costing procedure, termed a cost model, employs a process engineering approach for estimating total project costs as well as equipment and manpower requirements for uranium in situ leaching operations in either Texas or Wyoming. 80th capital and operating costs are generated by the model along with the overall production cost/pound U3O8 subject to a known rate of return. Conversely, rate of return on equity can be solved for, subject to a given price of yellowcake. During the course of the research effort, this cost model was applied 50 typical site conditions in Texas and Wyoming. Sensitivity rests were conducted for numerous key parameters to determine the cost influence attributable to incremental changes In parameter values. The results of these sensitivity tests along with a description of the in situ leaching cost model have been documented as Bureau of Mines, Mineral Research Contract Report No. J019912, "Cost and Sensitivities Analysis for Uranium In Situ Leach Mining," dated March 1981.

Jan 1, 1981

By Bernard G, Limpach R, Ulveling L

A major aspect in competitive ironmaking is to replace metallurgical coke by injecting alternative cheap fuels. Whereas in the past, heavy oil injection as well as on a lower scale natural gas injection have proved to be reliable, the progressing high price level of these fuels has prompted international interest in looking for alternative cheaper fuels, especially pulverized coal. Theoretical analysis and practical operations showed that for constant adiabatic flame temperature, potentially more coke may be replaced by injected coal than by heavy oil, because of less endothermic cracking of hydrogen components. Since about 1974, the ARBED-Group has been looking for alternative fuels and in 1976 came to conclusion to select for first trials pulverized lignite for the following reasons:

Jan 1, 1981

By F. A. Molloy

As a result of feasibility studies made in 1975 a 3-0 seismic reflection survey was shot over part of the Veendam salt pillow during 1978-1979. The Zechstein salt pillow, located in the northeast of the Netherlands near the town of veendam, occurs at a depth of 1400 m and contains three carnallite rich horizons over an interval of 300 m below top salt. MgCl2 brines are produced from these layers as feedstock for a magnesia plant, which starts up in 1981. Prior to the acquisition of the seismic data four wells had been drilled. The thickness of the carnallitite layers encountered in these wells varied between 50 and 125 meters. In view of these variations it was necessary to obtain a reliable isopach of the different layers. The 3-0 seismic survey covered an area of ± 4x4 km with a sampling interval of 20 m in all directions. The data was recorded it an area array using a 120 channel instrument. Final presentation of the data was in the form of 3-0 migrated acoustic impedance cross sections. The quality and resolution of the seismic data allowed reliable structural and isopach mans to be made. It was shown that the carnallitite layers are continuous over the area surveyed, whilst local thickening is "fault" related. Having this information brine production locations could be choosen in the thicker parts, allowing maximisation of production potential whilst avoiding faults and fulfilling mining regulations. A subsequent benefit of this approach is the possibility of using the seismic data to predict ore grade. Using the available wells as calibration points the acoustic impedance response of the seismic at the well was matched to the ore grade found. From these points a synthetic section was made with varying ore grades. Pre¬liminary results are encouraging and the liability of this predictive tool will be evaluated in the light of future drilling.

Jan 1, 1981