Search Documents

By Ray A. Rothrock

The in situ mining of uranium is the process whereby chemical lixiviant is injected by means of wells into, and flowed through, an ore body. The lixiviant reacts with uranium which has been previously oxidized making the uranium soluble. The solution is then brought to the surface by means of producing wells. In situ mining disturbs the ground-water quality in the immediate area. Since ground water is a natural resource used by man, care must be taken not to allow the lixiviant to escape the local mining area. Also, when the ore body is mined out, the area should be restored to as near its original state as is reasonably achievable. The return of ground-water quality to its original state can occur naturally over a long period of time or be enhanced using appropriate technological means.

Jan 1, 1981

By Eckersley J, Boyd G

A brief review is presented of the mechanisms and causes of spoil pile failures which have occurred at the Goonyella Mine. In particular, the results of a recent geo- technical investigation of the spoil dumps in the Cleanskin pit are briefly presented. Spoil pile hydrology is discussed in relation to the use of effective stress concepts in the analysis of spoil pile stability. Experience in relation to stabilisation of dragline dumps is discussed as well as the likelihood of current techniques being success- ful in the prevention of gross failures if prestrip material is placed in existing spoil piles. Parameters exerting a major control on dump stability are outlined.

Jan 1, 1981

To concentrate coarse mica particles using a dry beneficiation technique. Approach Concentrate coarse, II berated mica particles using a Bureau-designed system of crushers, screens, and a two-stage zigzag air classifier. How It Works Because mica has a flat plate-like crystalline structure, mica particles are significantly lighter than blocky gangue particles of the same size fraction. Thus an air classification technique can separate the flat, light mica particles from the heavier gangue particles. The ore, which Is first run through a standard jaw crusher, a roll crusher, and a hammer mill to liberate the mica, enters the rougher Zig-zag section through a rotating air lock. See photograph and diagram of a 2-stage air classifier. Airflow through the classifier can be varied according to the size of the particles being separated. The gangue material falls through the airstream of the rougher zigzag section and is discarded as tailings. The mica flakes are carried by the air-stream to the cyclone shown on the right side of the diagram, where they are collected. This rougher mica concentrate is fed to the cleaner zigzag section through another rotating air lock. The mica particles are again carried by the airstream but they are now collected In the cyclone on the left side. The cleaner concentrate leaves the left-side cyclone through a third rotating air lock and is rescreened to remove under-size material missed by the first screening. The final product of this pneumatic process is generally a high-grade mica concentrate. A generalized flow diagram for the pneumatic concentration method Is shown In the second diagram.

Jan 1, 1981

By C. J. Fauconnier

The various methods of detecting fires and heatings in collieries are reviewed. The methods described range from those relying principally on human senses to sophisticated methods employing infrared technology to detect traces of the products of oxidation and combustion. The advantages and disadvantages of various gases employed as indicator gases for the early detection of heatings and fires are discussed, and recommendations are made in this regard. The operation of a modern infrared carbon monoxide detection system is described, and the differences in operation and application of telemetric systems, tube-bundle systems, and up cast-shaft monitors are discussed In conclusion, some indication is given of the capital outlay required for typical early-detection systems.

Jan 1, 1981

By Johns A. L

The concept of the Melbourne Underground Rail Loop and the organ- isation to achieve its construction are covered in the companion papers (Reference 1, 2) and will not be repeated here. The Victorian Railways, as well as being the eventual operator of the Loop when it is completed by MURLA, have also been responsible as "Contractors" to MURLA for the construction of the "cut and cover" or "box" tunnels and related approach works located on existing Railway property. These tunnel connections link the existing suburban system to the new underground works. The following tabulation indicates the significant work volume involved in this cut and cover tunnelling exercise and which is covered in some detail by this paper.

Jan 1, 1981

By Arthur G. Strassburger

INTRODUCTION High in the Sierra Nevada Mountains of California, some 50 airline miles (80 km) northeast of Fresno, and near the John Muir Wilderness and Kings Canyon National Park, a large underground hydroelectric project is under construction. Pacific Gas & Electric (PG&E) Company's 1,125 MW Helms Pumped Storage Project exhibits a number of impressive statistics, unusual features, and other characteristics of interest to the tunneling or power plant designer and construction contractor. The most significant underground facilities include almost 20,000 ft (6,096 m) of 27-ft (8.2 m) diam concrete-lined pressure tunnel; 3,700 ft (1,128 m) of access tunnel; 1,600 ft (488 m) of steel-lined high-pressure conduit, 2 major underground chambers more than 1,000 ft (305 m) below ground; 3 deep vertical shafts, and one steep inclined shaft. Maximum static pressures within the conduits range from 200 ft (61 m) to 1,744 ft (532 m), with hydraulic transients that increase pressure to 2,500 ft (762 m). The purpose of these underground works is to provide 475,000 hp (354,350 KW) of water power to each of the 3 reversible pump-turbines, each connected to a 375 MW generator motor. The units, rated at 1,744 ft (532 m) maximum static head, are among the world's front-runners, considering the size-head combination. The Helms Project develops the existing power drop between two of PG&E's reservoirs, Courtright Lake and Lake Wishon. These reservoirs are retained by two concrete-faced rockfill dams completed in 1958, each storing approximately 125,000 acre ft (154 x 106 m3) of water. Although the project is intended to operate on a typical

Jan 1, 1981

By Jed H. Mosgrove

One of the most interesting of all the subjects required of persons studying the different facets of coal mining is coal mine gases. Some mine gases have been a real problem since the very beginning of underground mining, and in the early days there was insufficient knowledge to cope with them. The history of mining shows that until about the last 50 years, much work was done primarily by the hand methods which are primitive by today's standards. Miners had to contend with gases without the aid of enclosed lighting, permissible mine machinery, sophisticated testing devices, and high-pressure ventilating fans. In early days the miners were not educated about the different mine gases nor did they have the technical equipment to determine the actual composition of the deadly atmospheres they encountered. They simply applied a descriptive term to each gas or mixture of gases depending on its, effect on a person or the surrounding atmosphere. The gases or mixtures of gases were then referred to as "damps," a term which was probably derived from the German word "damps," meaning vapors or gases. The more common damps encountered were : Blackdamp A condition of the atmosphere in which a miner's light would be extinguished and in which breathing would be difficult, sometimes even resulting in suffocation. An atmosphere deficient in oxygen which could contain a combination of any of the mine gases. Firedamp A flammable mixture of methane and air which would either burn or explode when ignited. White Damp A mixture of gases containing carbon monoxide, most often found in mines during fires or after explosions.

Jan 1, 1981

By E. S. Vargas, T. W. Chapman, Samuel W-S Tse

Models for interphase mass transfer rates in the solvent extraction of metals are developed for zinc and copper chlorides being extracted by trilsooctylamine and for copper extraction by LIX 64N from ammonia solution. The approach is to adopt a stagnant film model on which film thicknesses are known and to derive the interfacial metal fluxes for the case where all reversible reactions are fast and locally equilibrated. A growing drop mass transfer cell is used to measure extraction rates. It is found that for the cases studied the transfer rates are mass-transfer limited On the other hand, copper extraction by LIX from acidic solution exhibits slow reaction kinetics, and earlier kinetics models are confirmed. Interactions that cause varying selectivity in the simultaneous extraction of copper and zinc chlorides are demonstrated.

Jan 1, 1981

By R. P. Beyer

As part of its thermodynamic investigations of mineral compounds, the Bureau of Mines has written an algorithm based on Newton's method for solving for the characteristic Debye temperature of a compound, from heat capacity and temperature data. A listing of a FORTRAN IV program based on this algorithm, for calculating Debye temperatures given heat capacities or for calculating heat capacities given Debye temperatures, is available from the author upon request.

Jan 1, 1981

Under the Town and Country Planning Act 1977 the Ministry of Works and Development has a responsibility for providing information to local and regional planning authorities on public works and matters of national development and importance, for the exercise of their responsibilities under this Act. One such matter which has recently become a source of concern is the development of South Island lignite. In 1979 the Ministry of' Energy produced a position statement outlining a programme of' research leading to the possible extraction of lignite in Southland or Central Otago for conversion into about 50 per cent of New Zealand's liquid fuel requirements by 1995. Understandably this possibility has caused considerable concern at the local level, expressed particularly by bodies such as Federated Farmers and the local authorities. In the absence of any factual knowledge short of mere conjecture been able to recommend to local authorities is that they limit their planning period to ten years. After this time more information regarding the size, nature, location and certainty of the proposal will permit a more accurate assessment of the implications of the York. While on holiday earlier this year I took the opportunity to visit opencast mining areas in Germany and England to gain an appreciation of the scale of impacts involved and discuss with those concerned the procedures used in planning for such operations. What follows is a brief description of these operations, a comparison with the likely development in this country and the extraction of what may be some relevant principles of' operation for the planning of an environmentally acceptable project. Please note that the views expressed in this paper are mine alone and are not necessarily those of the Ministry of Works and Development.

Jan 1, 1981

By Watson F. G

As an introductory paper of a series on the Melbourne (Australia) Underground Rail Loop extension to the extensive electrified suburban railway system the paper outlines the need for the Loop, legislative background, organizational establishment, engage- ment of consultants, design control, contracts, financial aspects, example of organizational flexibility and certification and transfer of the Loop to the Victorian Railways Board.

Jan 1, 1981

By Eugene F. Casey, John G. Ruggiero

INTRODUCTION Construction of tunnels in urban areas, especially reclaimed areas, pose many problems. The Red Hook Intercepting Sewer Tunnel, Contract 1A is a portion of the Red Hook Water Pollution Control Project located along the Brooklyn waterfront in New York City. This contract required the construction of a 2620 meter long (8600 L.F.), 3 meter (10-foot) diameter soft ground tunnel, eight Tunnel Manholes, nine Regulator structures, four Diversion and Tidegate structures and 765 meters (2500 L.F.) of branch intercepting sewers of diameters between .30 meters (12 inches) and 1.8 meters (72 inches). The construction contract bid price was $62 million with a duration of three years. The tunnel route crosses over five sets of operational twin cast iron subway tubes with clearances ranging from 4.3 meters (14 feet) to as small as 0.35 meters (14 inches). The route of the tunnel traverses historically interesting areas which have been reclaimed over the last 200 years. This paper is a case history describing the contractor's methods utilized to successfully advance the work through the above problem areas. LOCATION The Red Hook Intercepting Sewer Tunnel is located in the Borough of Brooklyn of New York City. The route is

Jan 1, 1981

By R. L. Loofbourow, Robert R. Miller

Deep, stable, unlined space promises secure, efficient, acceptable solutions to several current problems. With truly favorable conditions, it can be economic as well. The basic requirement is sufficient sound, tight rock at required depth. This and unusual surface requirements point to special testing. An objective is to describe conditions for planners, estimators and contracts. A first stage concept study needn't be prolonged but should overlook nothing significant. Although observations and tests on core are considered essential, time and expense can be cut by supplementing then with tests on walls of rotary or percussion holes. In some places initial drilling could be shallow.

Jan 1, 1981

By Konishi Y, Morioka Y, Okabe K

A part of the results of dissection survey of Chiba No.1 blast furnace, Kawasaki Steel Corporat- ion, is presented. Distributions of coke size and of slag and metal holdup are shown in the region of the dropping zone. A similar relation to the irri- gated packed bed is obtained. The distribution of coke size, coke temperature and liquid holdup are measured in and around the raceway. The shape of raceway in the horizontal and vertical sections indicates that each raceway worked individually. Liquid flow in the dropping zone and around the raceway on the basis of holdup measurements is Discussed.

Jan 1, 1981

By David K. Denton

Results of the mineral resource study of the Upper Priest Lake RARE II study area indicate a low potential for the discovery and economic recovery of silver and lead in the Prichard Formation near contacts with the Kaniksu Batholith in the vicinity of the Mountain Chief Mine (fig. 1). Silver and lead minerals locally occur disseminated and in irregular quartz fissure-fillings in the Prichard Formation. Between 18^6 and 1967, 105 lode raining claims were located in the study area. The area was designated for "further planning" in the Final Environmental statement but was later changed to "nonwilderness" by President Carter after work was scheduled for the area.

Jan 1, 1981

By Bernard L. Cohen

INTRODUCTION The most serious occupational radiation episode in U.S. history was the exposure of uranium miners to radon daughters in the 1945-1968 time period. Although the maximum permissible dose at that time was 12 WLM (working level months) per year, average exposures were several times that figure, and ten times higher exposures were not uncommon. Starting in the early 1960s, mounting epidemiological evidence appeared for an excess incidence of lung cancer among these miners; up to 1974, there was an excess of 134 cases (159 observed vs 25 expected) among the 4000 in the group under study (NAS-1980). When this excess became apparent, the Federal Government took jurisdiction, greatly tightened enforcement, and in 1969 lowered the maximum permissible exposure to 4 WLM per year. These standards were met largely by a great improvement in ventilation. As a result of these measures, average miner exposures were reduced 5-fold from 1965 to 1968 and by another factor of 3 by 1970. In 1978, the 4 WLM/year maximum permissible exposure was exceeded by only 37 of 7500 underground miners, for only 16 wars it exceeded by more than 25%, and for only 8 was it exceeded by 502 (AIF-1980). The average exposures to the various groups are listed in Table 1. We see that the average exposure for all miners was 1.03 WLM, and for those who worked essentially full time underground it was 1.45 WLM. For purpose of later discussion, it will be convenient to choose a single value for average exposures. In view of the fact that employment situations and job categories are bound to vary over a lifetime of work, we take this to be 1.3 WLM/year. The purpose of this paper is not to dwell on history, but rather to address the question of whether or not this present situation is satisfactory. This question was considered recently by a study group under the auspices of National Institue of Occupational Safety and Health (NIOSH-1980) and it answered the question in the negative, concluding that the maximum permissible exposure should be substantially reduced. However, their arguments were incomplete and were lacking in perspective. The principal thrust of this paper is to provide some of the material overlooked. RISK TO URANIUM MINERS FROM RADON EXPOSURE In order to quantify the risk to uranium miners under present working conditions, it is first necessary to estimate the risk of lung cancer per WLM of exposure. The most straightforward way of doing this is to use the data on the group of uranium miners under study. These are listed in Table 2 for 8 exposure ranges and for the total group (NAS-1980). If all data are given equal weight, the risk is seen to be 3.5 x 10-6 per year per WLM. Much can be said in favor of using this value for the risk as dose independent; it is within one standard deviation (SD) of the observations in 5 of the 8 dose categories (as expected from the definition of SD), and within 2 SD for all 8, and for the three cases differing from the mean by more than one SD, two are above and one is below. However, the uranium miner exposures in the present situation will be far below those covered in Table 2, so it is worth considering the possibility that the risk differs from this at low doses. From the last column of Table 2 we see that the experience from all exposures below 600 WLM indicates a risk higher than the mean for the entire group by more than two standard deviations (the value 600 WLM in this comparison was deliberately chosen to maximize this deviation; for exposures below 360 WLM and 840 WLM, the excess is only 1.0 and 1.6 standard deviations respectively). In view of this tendency for the risk to be higher at lower dose, we will take the risk to be 5.0 x 10-6 per year per WLM in what we will refer to as model A. This risk estimate is based entirely on exposures much [higher] than those that will be experienced by

Jan 1, 1981

By A. V. Petty

In accordance with its objective to maximize minerals recovery from secondary domestic resources, Bureau of Mines conducted research on recycling chrome refractory wastes. Since 20 pct of the U.S. demand for imported chromite is used in the production of refractories, primarily for the steel, copper, and glass industries, samples of used chrome-containing refractories from copper converter and reverberatory furnaces were investigated to determine their potential for recycling. The samples were beneficiated using a combination of wet magnetic separation, flotation, and leaching techniques, and the concentrates were reformed into briquets for refractory evaluation. Small refractory test specimens produced from the beneficiated concentrates gave modulus of rupture values at 1,350° C comparable to those of commercial mag-chrome brick of similar composition; however, grinding the waste refractories to at least minus 65-mesh was required in order to liberate the metallic copper. Most of the copper was easily recovered using conventional beneficiation techniques, but the finely ground chrome concentrate would require briquetting, calcining, and crushing to produce a coarse grain suitable for recycling into secondary mag-chrome refractories.

Jan 1, 1981

By James Lee Hibbard, Doraiswami Ramkrishna

A population balance model accounting for the transient variations in drop size distributions in a stirred liquid-liquid system is analyzed for its effect on chemical reaction conversion in a stirred, batch reactor. The analysis is applied specifically for phase transfer catalytic reactions, which indicates that transient effects of evolution of drop size distributions may be important in such systems.

Jan 1, 1981

By Bennet A. G

As part of the construction of the Melbourne Underground Rail Loop it was necessary to construct two 7 metre diameter tunnels, each 100 metres in length, by shield driven excavation through an alluvial valley at Elizabeth Street. The tunnels had a primary support of bolted precast reinforced concrete liner blocks and were excavated with the aid of compressed air. The work was undertaken by the Tunnelling Group of the Melbourne and Metropolitan Board of Works as nominated sub-contractor to John Holland (Constructions) Pty. Ltd. The paper describes some of the problems associated with the construction of the above tunnels and the methods used to overcome them. In particular

Jan 1, 1981

By V. Coffin, T. Cienski

"(Figure 1) Reagentized pulp enters into the column at about 1/4 of the distance from the top. Inside the column it meets with a downward flowing stream of water and with an upward flowing mass of air bubbles. Flotation takes place in this counter current system while at the same time fine gangue particles are washed off the froth before it reaches the overflow lip at the top of the column. The main operating features of the column flotation are as follows:a) No moving parts. Solids are kept in suspention not by an agitating action of a propeller but by settling down against the rising air bubbles.b) Wash water. Spray pipes are installed a few inches below the froth surface and deliver required volume of water. The purpose of this water is twofold:(i) it keeps in balance the flow of material through the column and(ii) it washes rising froth in the froth layer as well as removes unwanted fines attached to the bubbles at the lower flotation section. As a result the concentrate produced is of higher purity than in the conventional flotation. Column is characterized by very high up-grading. However, even temporary disruption of wash water supply results in a drastic drop of concentrate grate.c) Flow balance. (Figure 2) For the correct operation volume of the underflow (tail) is larger than that of the feed. The difference is made up by the wash water. This difference called bias is predetermined and ranges from some 4 to 15 USGPM depending on the size of the unit and process requirements."

Jan 1, 1981