Search Documents

By W. J. Guay

Scrubbing of simulated copper reverberatory furnace gases containing 1.0 percent sulfur dioxide with the minus 74 ~m fraction of the San Manuel tailings has shown sulfur dioxide removals of almost 100 percent over an effluent pH range of 3.1 to 4.6 and a wide range of liquid to gas ratios with absorptions of 11 to 17 Kg of sulfur dioxide per tonne of minus 74 um slimes. The high reactivity of the tailings slimes with S02 indicates that the reaction rate is not controlled by the slow dissolution of calcium carbonate in sulfurous acid which characterizes scrubbers using ground limestone. The interpretation of these results has been considerably enhanced by wet chemical analysis and emission spectrographic analysis which show that calcium and iron account for about 90 percent of the SO2 absorption with the rest being accounted for by aluminum, magnesium, potassium, and sodium. Mineralogic examination confirms the, chemical and spectrographic analyses showing that the major constituent removed from the slimes is calcium carbonate, with lesser amounts of chlorite and montmorillonite (silicates containing iron, magnesium, aluminum, and calcium) being removed.

Jan 1, 1981

By Peter G. Tregelles, Derek K. Barham

Introduction A successful step towards mechanisation of the collier's work was taken in 1954 when the first Anderton shearer loader was commissioned in Lancashire, and progress was reinforced in 1956 when the first powered supports were installed in Nottinghamshire. By 1970, virtually 100% of the coalfaces in the United Kingdom were mechanised and the industry's productivity had doubled. In 1961 the National Coal Board recognised that the next move towards greater productivity and improved safety would be to automate the longwall system. What was not well enough understood, however, was that the basic prerequisites of automation - reliability and measurement - had not yet been achieved. Consequently, the schemes for automatic longwall faces and for an entirely automated colliery were abandoned at the close of the decade. A review of mining research and development policy, commissioned by the Board in 1974, confirmed that the system of longwall mining had great potential for investment and that the short-term policy of automation must once again be pursued. Since then, aided by advances in computer technology, systems for automating the transport of coal from the face to the coal preparation plant have been successfully instituted. Applications of sub-systems dealing with the conveyor, coal preparation plant, and various items of fixed plant are now at the exploitation stage. In the medium term, a number of key problems have been identified, which will arise once the productivity from the coalfaces has doubled, as it is now expected to do in the next five years. One of the most important of these problems is machine guidance, and considerable research and development work is now being carried out in this area. This paper reviews the work on machine guidance prior to 1974 and explains the programme on which the National Coal Board's Mining Research and Development Establishment is currently working.

Jan 1, 1981

By Claes G. Björk

Over the past decade mined unlined rock cavern storage for crude oil and refined products has become economically more attractive. This trend is likely to continue, primarily due to advances in excavation methods, rising steel costs for above ground tanks and larger capacity requirements. The construction experience related in this paper comprises the excavation of more than 80 storage facilities (total capacity 90 million bbl) for crude and refined products ranging from propane to heavy fuel oil. This paper also deals with the experience gained as well as the problems derived from the utilization of these oil storage facilities.

Jan 1, 1981

By R Fox, R Watt

On behalf of ICI's group of explosives companies around the world, a research programme is being undertaken to develop a new electrical shotfiring system which will have markedly improved safety features and operational advantages over existing initiating systems. The paper describes the development of the 'Magnadet' Electric Detonator and 'Magna' Primer and the field experience to date. It also indicates those areas where further work is being carried out on modification of the basic designs to meet specific application requirements.

Jan 1, 1981

By H. D. Sharma

INTRODUCTION Uranium mill tailings, by-products from the mining and milling of uranium oxide contain all decay products of uranium-238, uranium-235 and all the Th-232. The ore containing all daughter products of the parents U-238, U-235 and Th-232 is ground to approximately 50% under 200 mesh particle size and after extraction of uranium, the residue, described as tailings, is discharged into natural depressions confined by dams. These deposition sites are referred to as tailings ponds. Tailings ponds are located in two mining districts, Bancroft and Elliot Lake in the Province of Ontario, Canada. Some parts of tailings ponds are dry up to a depth of several meters, whereas other parts have a water table very close to the surface and still others are covered with water. The extent to which the daughters of uranium isotopes are in equilibrium with the parents U-238 and U-235 is dependent on the age of the deposit in which uranium occurs and the extent to which the decay products are removed by geochemical processes. In the mining district of Bancroft, the deposit is known to be approximately 1 billion years old, whereas in Elliot Lake, the deposit is considered to be approximately 2 billion years old. The ratio of radiogenic lead isotopes Pb-206 and Pb-207, can provide some estimates concerning the age of the deposits. If the tailings are not affected by geochemical processes, the tailings would contain all the daughters of the 4n+2 and 4n+3 series in equilibrium concentrations. The equilibrium activities of some members of the 4n+2 series are calculated in Table 1. [ ] The amount of radiogenic stable lead isotopes depends on the age of the ore deposits. If the deposit in each district is of the same age, a definite relationship is expected with respect to the activity of Pb-210 and the radiogenic stable isotopes. Approximately 33 million tons of the tailings have been deposited in the early 1960's, approximately 20 years ago. During this period of storage, the segregation of uranium daughters, like radium, the diffusion of gaseous product, Rn-222, and removal of precursors by geochemical processes, can cause dis-equilibrium. Earlier work concerned with the uptake of Ra-226 and Pb-210 by plants (Kalin and Sharma, 1981), indicated that the concentrations of Pb-210,in samples of the tailings taken, were lower than the expected equilibrium. The diffusion of radon from a variety of matrices has been studied (Tanner, 1964). It has been shown that the diffusion coefficient is dependent on the particle size in which its precursor is present, the moisture content and the surface conditions. The direct measurement of radon concentrations in the environment near the ponds is dependent on the metereological conditions. Kramer, Schroeder and Evans, 1964, have examined the variations in the concentration of radon near the ground level with respect to atmospheric variables, such as changes in barometric pressure, precipitation, wind velocities, thermal atmospheric instability. It is difficult to relate the total release of radon from the ponds to the atmosphere over an extended period. Our measurements of Pb-210 and total lead on tailings samples taken from 16 sites indicate that the ratios of the activity of Pb-210 to the mass of total lead can provide parameters which are helpful in the estimation of the total amount of radon and its decay products diffusing from the tailings ponds. In this paper, we present the results of measurements of activities of Ra-226, Pb-210 and total lead in samples from various ponds situated in both mining districts. The measurements were confined to samples taken at 0-25 cm depth from the surface.

Jan 1, 1981

By Wright R. J

The Commission called tenders for a four boom hydraulic jumbo, plus basket, on an art- iculated carrier in Sept. 1977. Atlas Copco submitted the successful tender in Jan. 1978 for the supply of a three boom jumbo, plus basket. The Promec TH470 jumbo was commiss- ioned in the 2000 m long Sophia tunnel in Nov. 1978. Adequate spare parts were not available during the first three months of operation and the hammers could not be overhauled at the recommended interval. One hammer was removed after drilling 13 600 m due to a crack in the intermediate housing. Tests were conducted with different types of drilling consumables. Both rope and Hi-teed threads were tested and found compar- able. The average penetration rate in the granite was 1.1 m/min. Initially the drillers were not experienced enough to operate the BUT 15ERH booms without causing damage to the booms and hoses. Drilling deviation espec- ially of the perimeter holes was greater than expected. It is now obvious that greater attention must be given to attracting, train- ing and retaining the right type of operator and maintenance fitter.

Jan 1, 1981

By M. J. Robinson, G. E. Blight, J. A. C. Diering

The mechanism of the flow of tailings slurry is examined, and a mathematical model is derived to describe the flow. Predictions based on the model are then compared with the flow that actually occurred near the shaft at Bafokeng after the No. I tailings dam had failed. The predictions are found to be of acceptable accuracy.

Jan 1, 1981

By -1ng. B. Stampa

Introduction The author investigates the technology available for mine flow reversibility by reversing the operation of the main fans. Air bypassing, reversed sense of impeller rotation, and blade angle overturning are indentified as the most important means of achieving the flow reversibility. The axial flow fan is studied in some detail and the important variables of fan capacity, pressure, and efficiency are compared. Although some references to rotor velocity vectors are made (Fig. 1) the subject is not presented in detail in order to stay within the paper's intent. Background Where applicable, the requirements of mine air reversibility are an important part of the overall mining operation and should be given proper attention during mine ventilation design. The need for preventing mine fires in intake shafts is the reason that, for a long time, it has been a requirement in the Eastern European countries to have the feature of flow reversibility built into all main mine ventilators. In West German coal mines, this requirement does not apply since higher priority is given to safety precautions. Some metal and mineral mines in the United States are required to have ventilation currents readily reversible in order to fight underground fires as stipulated by the Title 30, Mineral Resources, and by the mining laws of some states. From an equipment performance standpoint, assuming the validity of other flow technical data, the question of the ventilator flow reversibility is of ten related to the actual scenario of the begining of an emergency. Most of the time, the system operates within half of the design capacity only and assuming that the equivalent mine orifice is stable only a quarter of the design pressure must be produced by the fan in any event. For such an operating point, the effective gradient and energy losses can be disregarded since fire emergencies usually last for only a short period of time. Equipment Comparison Fig. 2 depicts a ventilation arrangement wherein the flow can be reversed through changing the functional position of the dampers (slideplate or blade type). Both axial or radial fans can be applied in this case. For the mine exhaust operation, slide plates (guillotines) I and I11 are opened while plates I1 and IV are closed. The flow thus encounters two reroutings, which due to the reverse ventilation flow cannot be equipped with proper sheet metal deflectors, and therefore large pressure losses result during the air reroute operation. When the intake operation is considered, the dampers I and I11 are closed and the pair I1 and IV is opened. For this arrangement, almost the same flow conditions exist as for the foregoing exhaust mode; however, one additional corner must be applied. Even if a highly efficient ventilator is used in one of the previously described systems, the additional pressure losses resulting from air rerouting plus those encountered between the planes "0" and "00" significantly affect the overall energy requirements. Illustrated in Table 1 are the relative component losses of even flows for evaluation of various detour arrangements. From the aerodynamics standpoint, when these components are being designed, serious consideration must be given to the individual levels of the pressure loss coefficient, 5. Should there be an increase in the sum of the loss coefficients due to the particular component selection such that, for example, the net change is 1.2; the resulting pressure to be produced by the fan can be calculated from:

Jan 1, 1981

By James Giulianelli

Personnel at the Jet Propulsion Laboratory (JPL) are studying the technology and applications of salt-gradient solar ponds (see below) for both electrical and thermal energy generation. The brine extraction and processing site operated by the Kerr-McGee Corporation at Searles Lake, California, offers ideal conditions for economic construction of solar ponds. Furthermore, since rising conventional energy costs adversely affect the economic recovery of brine by the present process, this site was selected for a study on the feasibility of integrating the solution mining of trona (Na2CO3?NaHCO3?2H20) in the lower salt with solar ponds for heating. The major emphasis of this study was to determine whether inexpensive thermal energy available at the brine extraction site would be useful in extracting increased mineral value from the resource. The present operation, which involves the simple extraction of the complex brine and its processing at the adjacent plant, is sometimes referred to as solution mining. Since the concept discussed in this paper involves injecting a heated sodium sulfate brine to dissolve carbonate underground, the proposed scheme is referred to as "enhanced" solution mining. The subject is discussed in greater detail in a recent JPL report. (1)

Jan 1, 1981

By Coin CDA

From a study of coke samples obtained from the tuyere level of four Australian Blast Furnaces, the nature of in-furnace coke degradation has been investigated. At the periphery of the raceway is a concentration of fines and the lump coke appears dull and rounded. However coke from the deadman is angular and relatively undegraded. Cokes made from higher rank coal appear to suffer preferential attack of the reactive maceral derived component (binder). The coke from lower rank coal appears to be attacked non-preferentially by the solution-loss reaction. Initial attempts to simulate these phenomena have given results consistent with these findings. From chemical analysis of the tuyere probe samples there appears to be a relative increase in carbon and decrease in-.sulphur and phosphorous between stockline and tuyere level. An overall decrease in coke mineral matter derived material was noted and associated with this was a significant gasification of silicon. Consequent formation of silicon carbide was noted.

Jan 1, 1981

By Mark S. Sanders

This report presents recommended visibility requirements for continuous miner, shuttle car and scoop operations and details the methodology used to generate them. A task analytic approach was used to define information requirements and visual features which served as sources of information. Information requirements were prioritized and the location of visual features determined. From this analysis, visual attention locations, containing one or more important visual features, were identified. A total of 71 locations-were identified for continuous miners, 54 for shuttle-cars and 54 for scoops. A procedure was developed for assessing whether operators in existing machines could be expected to see the visual attention locations. The procedure makes use of a Human Eye Reference Measurement Instrument (HERMI) designed for this project and an outside-in photographic procedure for documenting compliance with the recommendations. A sample of continuous miners, shuttle cars, and scoops were used to test the procedure. Results are presented in the report.

Jan 1, 1981

By Charles L. Kusik

As part of an effort to establish processes that could be exploited in case of adverse changes in international chromium production and trading patterns, this study was sponsored by the Federal Emergency Management Agency (formerly the Federal Preparedness Agency) through the Bureau of Mines, to experimentally determine the feasibility of recovering chromium from critical scrap metals containing significant quantities of this element. Based on a conceptual pyrometallurgical chromium recovery flowsheet developed at Arthur D. Little, Inc., the experimental program described in this report demonstrated key process steps for the recovery of chromium as ferrochromium in a batch process. The process involves oxidation of chromium into a slag phase, subsequent separation of the slag phase from the remaining metal, followed by reduction of chromium from the slag phase to produce ferrochromium.

Jan 1, 1981

By Peter L. Hofmann

Significant quantities of nuclear wastes were first generated in 1944 as a byproduct of the national defense program. To establish the current inventories and future projections of nuclear waste products is not a simple task. The Oak Ridge National Laboratory recently issued a report which now constitutes the official basis for nuclear waste inventories and projections. Radioactive wastes originate from five major sources (U .S. Department of Energy, 1980b) : (1) From the commercial nuclear fuel cycle related to the production of electricity , (2) From defense related activities, (3) From institutions such as hospitals, universities, and research foundations, (4) From industrial uses of radioisotopes, and (5) From mining and milling of uranium ores.

Jan 1, 1981

By F. F. Roxborough, P. King, E. J. Pedroncelli

This paper describes tests on the performance of a continuous miner in cutting South African coal. Although coal cutting has been investigated extensively overseas, the results have not led to significant changes in machine design because these machines find little difficulty in cutting the softer overseas coals at a fast rate. In general, the results of the tests show that cutting efficiency improves markedly as the depth of cut per revolution of the drum increases, and that the best spacing of picks on the drum is twice the depth of cut. Pick shape is of secon¬dary importance in terms of cutting efficiency, only small differences having been found between the performances of conical- and chisel-shaped tools.

Jan 1, 1981

By Russell G. Slayback

An integral part of site investigations for shafts and underground workings should be hydrogeologic evaluations of the need for and method of ground-water control. Such investigations should include: 1. Classification of the problem by aquifer type. 2. Integration of other site investigations with hydrogeologic programs, including assessment of the need for water control. 3. Planning and conduct of aquifer tests tailored to the aquifer situation. 4. Evaluation of pumping requirements to achieve water control objectives. 5. Scheduling of dewatering for optimum results and costs. 6. Evaluation of environmental impacts of pumpage and water discharge. 7. Planning of operational monitoring for program modification and liability limitation. Early hydrogeologic involvement can result in avoiding unnecessary duplication in site investigations.

Jan 1, 1981

By Wilbur C. Helt, Joseph J. Yancik

Throughout the history of mankind, the principal use of coal has been to produce heat through combustion. The heat is used in many ways: to warm air space for our comfort; to provide heat or energy to power industrial processes, such as cement and steel production; and to produce electricity. Because it is our nation's most abundant fossil energy fuel, coal in the late 20th century is on the threshold of becoming a significant source for synthetic liquids and gas energy fuels for this country. This is made possible by conversion processes which can change solid coal into various synthetic gases and liquids. These coal-derived fuels are nearly identical to the processed fuels and chemicals provided by natural gas and crude oils, which presently provide almost all the petrochemical feedstocks and energy fuels needed for the residential, light commercial, and transportation markets. A revolution is beginning to take place, not only in the United States, but in many other countries with a return to a coal-based energy economy. Also, new combustion and conversion technologies which are compatible with national health arid environmental goals are rapidly emerging. These technologies will allow coal's use to be expanded not only in its traditional markets, but also to supply markets held by natural gas and crude oil. With the worldwide decline in natural gas and crude oil reserves, coal is being looked upon to meet the energy demand. Because of these new coal conversion technologies, coal will no longer be only a combustion fuel, but a valuable raw material for production of a variety of clean fuels and chemicals. MARKETS FOR COAL: PAST AND FUTURE A simplified diagram of the marketing network for coal is shown in Fig. 1. As shown in this figure, coal is transported to its traditional

Jan 1, 1981

By M. B. Sizgoric

Quantitative mineralogy is used in a study done on an Inco Metals Company nickel sulfide occurrence from 'the Thompson area in Northern Manitoba. The study included: a) determination of the variations in chemical composition of the ore minerals; b) determination of the liberation of the ore minerals for the various types of ore and for different feed grinds; c) assessment of the preliminary mill test results by comparing the mineral distribution in the different tailings. Preliminary mill test results had outlined three main problem areas: 1) unacceptabiy low grade concentrate with, 2) very high weight recovery and, 3) low pyrrhotite rejection resulting in a high sulfur concentrate. The mineralogical study readily explained these results by showing that: 1) between 20 and 40% of the nickel in the feeds and 55 and 75% of the nickel lost in the tailings is associated with pyrrhotite. This accounts in part for the low grade of the concentrates obtained at high recoveries: 2) hexagonal nonmagnetic pyrrhotite constitutes over 90 percent of pyrrhotite. Since hexagonal pyrrhotite floats more readily than monoclinic pyrrhotite, this could be part of the reason for the undesirable high pyrrhotite recoveries into the concentrates. Further test work to establish both the optimal grind and the best conditions for pyrrhotite rejection is therefore mandatory.

Jan 1, 1981

By T. A. Kubala

Electric discharge ignition has been reinvestigated in a modified Hartmann apparatus for lycopodium powder with air. Minimum stored energy to ignite air dispersions of lycopodium was 25 to 30 mj; ignition occurred with 1 gram of lycopodium dispersed into the 2.7-liter vessel. Ignition energy was measured as a function of the weight of powder used, although some reservations are expressed concerning the uniformity of the lycopodium-air mixtures. In particular, wall layers of lycopodium, remaining after dispersal of 1 gram of lycopodium, were as easily ignitable as the most easily ignited air dispersion. Thus, an unanswered question has arisen concerning the role of surface coatings in the flammability of all marginally ignitable mixtures.

Jan 1, 1981

By Francis E. Federspiel

Silver and gold are the principal metals in the study area; they occur in quartz veins or silicified portions of shear zones. In some deposits, lead, antimony, zinc, and molybdenum are associated with gold and silver. A uranium-bearing buried stream channel lies near the southern boundary. Since 1850, more than 300 lode claims and relocations have been recorded mainly in the southeast corner of the study area (fig. 1). Complete mine production records are not available; however Clark (1977, p. 28) reported less than $300,000 of gold and silver were produced, mainly from the Exchequer, IXL, and Pennsylvania Mines. Other mines in the area probably yielded are before 1900, but early records are not available.

Jan 1, 1981

By M. M. Papic

"This paper describes the Sasol coal liquefaction process, as used in South Africa. It covers coal supply, coal gasification, gas purification, Fischer-Tropsch synthesis, the major utility systems involved and the economics of the process.IntroductionThe Sasol coal liquefaction process is based on Fischer-Tropsch synthesis of liquid fuels from carbon monoxide and hydrogen, which are in turn obtained by gasification of coal with steam and oxygen. The process is shown schematically in Figure I.The first step in the process is coal preparation, in which the coal is crushed and screened to a 3-50 mm size for gasification on one side and to -3 mm size for steam and power production on the other. Oxygen needed for coal gasificatoin is produced in the air separation plant.Coal is gasified under pressure by steam and oxygen in the Lurgi gasification plant, where raw, impure gas is produced . The raw gas is first washed in a scrubber with a circulating gas liquor, heat is then recovered from it in a waste heat recovery boiler and the gas is further cooled for purification. Water-insoluble materials (tar oils) in the gas liquor are separated from aqueous solution and sent to tar refining for the recovery of tar products. The aqueous portion of the gas liquor goes to a Phenosolvan solvent extraction process, where phenols and ammonia are recovered. Water then proceeds to the effluent treatment plant.The scrubbed and cooled raw gas goes to a Rectisol gas purification plant, where all components other than hydrogen, carbon monoxide and methane are removed as completely as possible by absorption in refrigerated methanol. The acid gases (CO2, H2S) stripped from the methanol in the Rectisol unit are processed in a Stretford plant for recovery of sulphur. Regenerated methanol is returned to the process. The purified synthesis gas is passed to the fluidized-bed Synthol reactors, where Fischer-Tropsch synthesis reactions take place.The synthesis products are recovered in a product recovery unit as separate streams of decant oil containing higher-molecular- weight hydrocarbons, light oil comprised of lower-molecular- weight species, the aqueous stream containing water solubles, a C3/C4 stream, a C2 stream , a methane stream and a hydrogen-rich stream. Most of the hydrogen is recycled to the Synthol reactors; a major portion of the methane is reformed to hydrogen and carbon monoxide for recycle; the C2 fraction goes to an ethylene plant; and liquid streams proceed to the product refinery.The product refinery is used to upgrade and purify the Synthol products to specification fuels and chemicals.Sasol l, the first coal liquefaction plant in South Africa , was built in 1955. It is still operating and has a product output of about half a million tonnes per year. The Sasol II plant is in a commissioning stage and will be in full operation in 1981. It is about five times the size of Sasoll. It uses over 12 million tonnes of coal and produces more than 2 million tonnes of saleable products annually (1,2,3). The Sasol llI plant, which is a mirror image of Sasol II, is under construction and scheduled for completion in 1983."

Jan 1, 1981