Search Documents

By P. M. Krishna

An example illustrates the use of ASTM Standard E901-82, Classification System for Uranium Resources. The example demonstrates the dynamic nature of the process of classification and attests to the necessity of addressing both the aggregate needs of broad-scale resource planning and the specific needs of individual property evaluation. Problems that ,remain in fixing the classification of a given uranium resource include the uncertainty in estimating the quantity of undiscovered resources and resolving the differences that may exist in deciding when the drill-hole spacing is adequate to determine the tonnage and grade of discovered resources.

Jan 1, 1983

By John H. Canterford

The adsorption of uranium onto Wyoming bentonite was measured in carbonate media over the range pH 8-11. Uranium was removed from solution onto the solids by a rapid reaction, proposed to be adsorption of the anionic uranyl tricarbonato complex onto edges of the clay platelets, and a slow reaction which may be precipitation of a hydroxide. The changes in uranium content of the aqueous and solid phases of a uranium ore carbonate leach slurry were also measured as the slurry was progressively diluted. There was an increase in the uranium content of the solids as the pH of the suspension was lowered, as was observed with the Wyoming bentonite. The results indicate the conditions that should be met with respect to pH control in order to prevent the problem of excessive uranium adsorption in the counter-current decantation washing circuit of a conventional leaching process, as well as in the leaching and restoration phases of carbonate solution mining.

Jan 1, 1983

By C. Y. Kao, Roger Y. Cheng, C. S. Hsieh

The mushroom-shaped Minghu power cavern located in central Taiwan is 21.2 m (W) by 40.5 m (H) by 127.2 m (L) and is designed to house 4 units of power generating-pumping equipment with a total capacity of 1,000 MW. This paper presents an introduction to the geological conditions at the cavern site; the rock mechanical tests undertaken; the design approach adopted; the construction method and sequence followed; and the instrumentation provided in the roof arch to monitor the behavior of the surrounding rocks. The measured data collected from the embedded instruments will be compared with those obtained from theoretical analyses and presented in this paper. Several technical problems encountered during the construction stage are covered and the solutions of these problems are also described therein.

Jan 1, 1983

By Larry D. Wayland

Almost 100 sedimentation ponds were conceptually designed for a large surface mining study area in northeast Texas. An approximate procedure was developed to economically estimate construction quantities in order to predict surface water control costs. This procedure utilized site-specific empirical relationships developed from detailed analyses on a representative number of proposed sedimentation ponds. Use of these equations provided earthwork volumes, and spillway pipe lengths. The procedure developed for this study is presented along with the results of a verification analysis.

Jan 1, 1983

The "Industrial Minerals" sector of the Australian minerals industry over the past decade or so can be seen to be moving away from a somewhat ad hoc grouping of producers to a more highly integrated and sophisticated industry in which products are being more stringently specified and greater amounts of capital are being spent.

Jan 1, 1983

Cobar Mines Pty. Limited (CMPL) uses sodium sulphite as the principal depressant to attain selectivity in copper flotation prior to sequential recovery of lead and zinc. The usage of sodium sulphite is examined both from a theorectical viewpoint ana from the manner in which the copper circuit at (MPL has developed. The results of relatively recent investigations, both in the laboratory ana the plant, are discussed aria shown to support the present operating Techniques.

Jan 1, 1983

The need for ventilation around mine workings derives from the various gases found in mine atmospheres and CH4, the principal diluent is in quantity depending upon several factors. Several of these are seam thickness, depth of cover and working method and the French Regulations typify controls on coal mine ventilation. There are many factors affecting production of CH4, in addition to coal production, such as the geological setting of the working seam, the geometry of workings and the rates of advance. The possibilities of spontaneous combustion should not be overlooked. The complexity of high production modern colliery layouts is such that sometimes there maybe 200 airway branches. There are specific differences in ventilation networks between the mining methods of rooms and pillars, shortwalls and longwalls as affecting resistance losses, as well as necessary airflows and ventilating

Jan 1, 1983

Saxonvale mine is a multi bench open pit coal mine developed to its Stage I capacity of 1.75 Mt/y of run of mine coal. Detailed engineering studies for the mine commenced in April 1980, approval to proceed with the development was received in July 1980 and first coal shipments were made in April 1982. The engineering and project management of the mine development was carried out by BHP Engineering. This paper outlines the design and site administration for the development and describes both the organisation structure and the control and administration procedures used by BHP Engineering to ensure that the project was Successful.

Jan 1, 1983

By Richard D. Hagni

Mississippi Valley-type ore deposits contain significant quantities of minor elements, which are present partly in the form of separate mineral phases and partly in solid solution in the major sulfide phases for which these deposits are exploited. These elements, as separate phases, are: copper, mainly in chalcopyrite and enargite; cobalt and nickel, chiefly in thiospinels and bravoite; rare earth elements associated with certain fluorites; and native gold. Many economically important minor elements occur in solid solution in sphalerite, including silver, cadmium, iron, germanium, gallium, indium, thallium, cobalt, nickel, and mercury. Significant amounts of silver and antimony, and perhaps very small amounts of gold, are present in solid solution in galena. Chalcopyrite may contain small amounts of silver, molybdenum, bismuth, cadmium, cobalt, and nickel. Marcasite and pyrite may contain silver, thallium, cobalt, and nickel. Although some of the minor elements contained in the Mississippi Valley-type deposits are currently recovered at the smelters and refineries, many are lost in tailings, sludges, and slags; consequently, important quantities of these elements are potentially recoverable as non-conventional resources.

Jan 1, 1983

By G. Donald Emigh

Nothing is more important to life-plant and animal-than phosphate. Its compounds are essential to the energy functions of all living systems and for the formation of bones and teeth. Animals get their phosphate from eating plants and other animals, or domestically from feed supplements. Plants get their phosphates from the soil. Man's most important use of phosphate is for fertilizer; approximately 95% of the world's phosphate rock production is consumed by fertilizers. Most of the balance is processed in electric furnaces into elemental phosphorus, the important raw material for making industrial phosphates. Recovery of uranium from phosphates has been possible but not widely used. However, recent significant developments have generated interest in such recovery in the US and elsewhere. Phosphate occurs in all igneous and sedimentary rocks, and in all fresh and salt water. However, economical recovery is limited to deposits where natural concentration of the phosphate mineral has occurred. Occasionally natural concentration is great enough that the material can be used as mined; generally, however, the ore is low grade_ and must be concentrated. Phosphate rock is produced in 31 countries. Fig. 1 shows the location of major phosphate rock producers as well as some of the known phosphate deposits not yet in production. In the last decade the world phosphate industry has experienced steady growth. World production rose from 98 Mt of phosphate rock in 1973 to 140 Mt in 1982. Fig. 2 shows the growth curve of rock production and graphically illustrates the almost straight-line rise since 1945 in both US and world production. Table 1 gives the breakdown, by countries, of world rock production, 1974 through 1979. Table 2 shows US rock production by producing areas. Definitions of Terms Used in the Phosphate Industry Phosphate Rock: Commonly called rock in sedimentary deposits and apatite in igneous deposits. Those expressions generally include any mined, or mined and beneficiated, fluorine-containing calcium phosphate used as the raw material for the next stage of manufacturing. The average phosphate content in rocks is 0.1 to 0.2% P2O5, as documented by McKelvey (1973). About 200 minerals contain more than 1 % P2O5. However, the important mineral in igneous rocks is fluorapatite, [Ca5 (PO4),3 F], containing about 42% P205 and 3.8% F2; in sedimentary rocks the important mineral is francolite, a carbonate fluorapatite containing up to 2% molecular CO2. Both are in the apatite family of minerals. Most phosphate rock, whether beneficiated or not, is a fine-grained material. The expression phosphate rock has no relation to its phosphate content. For example, phosphate rock from Idaho used in the production of phosphorus may contain about 24% P205, whereas rock from Morocco may contain 36.6% P2O5. Phosphorite: A deposit of phosphate directly or indirectly of sedimentary origin, which is of economic interest. Grade of Phosphate Rock: The calcium phosphate content of phosphate rock is expressed in different world areas by one of the following terms: BPL (bone phosphate of lime) TPL (triphosphate of lime) P2O5 (phosphorus pentoxide) P (phosphorus-not commonly used) An illustration of relationship is: 80% BPL = 80% TPL = 36.6% P5O2 = 16% P

Jan 1, 1983

By Sam S. Arentz

Storm King Mines began with the concept that the resource potential of thick and steeply pitching seams of the Grand Hogback region of Colorado could be mined profitably. Two large tracts of private land (fee coal) were acquired; approximately 23.8 km2 near Glenwood and 16.2 km2 near Meeker. Figure 1. Although both properties have substantial coal reserves, one has several distinct advantages in developing a competitive mining operation. Table 1 illustrates these advantages. Among the most important considerations from an economical point of view are proximity to railroad, highway, labor force, quality of coal, seam thickness, and source of water. As can be seen, Storm King Mines' property is adjacent to the main line of the D & RGW Railroad, 1-70, and the Colorado River. The cities of New Castle, Glenwood Springs, Silt, Rifle, Carbondale, and Parachute are within short commuting distances and have available skilled labor.

Jan 1, 1983

To test the feasibility of hydraulic borehole mining for the recovery of phosphate ore from the deep, water-saturated deposits of northeastern Florida. Approach Phosphate ore is remotely extracted through a Bureau of Mines-developed hydraulic borehole mining system. Hydraulic borehole mining can remove underground ore deposits that cannot be economically mined by the usual open pit or underground methods. It is environmentally compatible, causing none of the surface disruption or ground water pollution usually associated with other methods of mining. Selectivity of the borehole mining system also allows economical recovery of small or discontinuous ore deposits while minimizing the removal of host rock. The hydraulic borehole mining system has been used successfully in the past to mine uranium ore and oil sands. (For examples of these and other applications of borehole mining see T Technology News Nos. 97, 95, 63, 56, and 48) How it Works A 16-inch-diameter borehole is drilled from the surface down into the buried mineral deposit, and the mining tool is installed. The borehole mining tool consists of a 12-inch-diameter pipe string and accessories capped with a three-passage swivel, and ending with a mining section. The mining section has four slurry inlets and an eductor located near the bottom of the section and a single cutting nozzle located near the top. The tool generates a high velocity water jet that erodes and slurrifies the ore. The slurry is drawn through the inlet into the eductor which lifts it to the surface where it is deposited into a slurry discharge sump. All the support equipment is located and operated on the surface; only the mining tool portion of the system is underground during the recovery operation.

Jan 1, 1983

By Louis C. Just, Robert L. Sandefur, Carl E. Williams

In 1981 Ertec Rocky Mountain, Inc. completed a significant development in contemporary planning support; MINEPAK was completed, tested on various properties and offered for license. MINEPAK was one of the first computer systems for ore body analysis and mine planning that - Was designed as an interactive and completely integrated system - Was portable so that it can run on many hardware systems - Was really user friendly - Can run on minicomputers and on some microprocessors - Was built around a data base management system MINEPAK was designed to be a completely general block modeller and it achieved that goal. Since it contained a gridded file type, surfaces could be easily modelled but the system needed extensions to allow layered deposits to be modelled with the same ease as block models. So COALPAK was designed. COALPAK is an extension as well as a modification of MINEPAK. A 'layer' file type was defined and retrofitted into the existing system, new software tools were developed for modelling layered deposits, and tools for strip mining were written.

Jan 1, 1983

By W. C. McLaughlin

Under a cooperative agreement, the Bureau of Mines, Magma Copper Co., and ASARCO, Inc., tested backfilled ground support systems at t.wo elevations in Magma's San Manuel, AZ, mine. The tests were mainly for guidance in designing the loading crosscuts of the new ASARCO Sacaton underground mine. Two-piece, wide-flange steel sets for 8-by 8-ft (2.44-by 2.44-m) and 11-by II-ft (3.36-by 3.36-m) openings were designed. Set spacing was 3 ft (0.91 m) and 5 ft (1.52 m), respectively. After erection, the sets were lagged with various test materials. The void between the lining and the ground was backfilled with sand and pea gravel. Instruments measuring strain (used to determine changes in stress) were placed beneath the sets and in the backfill. Results indicate the backfilled sets in the smaller drift (2315 grizzly level, panels 6 and 7) of 8-by 8-ft (2.44-by 2.44-m) cross section are a viable permanent support system, lower in cost than the standard formed concrete. Results are inconclusive in 2615 grizzly level, panels 5 and 6, where wide-flange steel sets were used with 5-ft (1.52-m) long concrete gob lagging of T-design.

Jan 1, 1983

By Y. P. Malhotra, JE. C. Carter

"Syncrude's overburden removal requirement ranges from 20 million to 30 million bank cubic metres per year to meet tarsand demands for the production of 129,000 barrels of synthetic crude oil per day. The economic tar-sand lies beneath a variable thickness of overburden materials, composed of silts, clays, some sands of lacustrine origin, wind-deposited sand dunes, and out-wash sands and gravels.For the removal of overburden, Syncrude commissioned its own mobile equipment fleet in January 1981. This fleet consists of two Demag 241 hydraulic shovels, ten Titan 33-15B trucks and support equipment. Prior to this, all overburden removal was being carried out by contractors.This paper presents an overview of overburden removal at Syncrude, with particular reference to the performance of its own fleet.IntroductionThe Syncrude Tar Sands Plant was officially opened on September 15, 1978. After an expenditure of approximately $2.26 billion, the second and the largest commercial tarsands plant was on stream toward a permit production rate of 129,400 barrels of synthetic crude oil per day. The Syncrude Plant, a joint venture of six oil companies, the federal government and the Alberta government, is a major step forward toward the goal of Canadian energy self-sufficiency.The Mildred Lake operation of Syncrude Canada Ltd. Is located 40 km north of Fort McMurray and 480 km northeast of Edmonton in the Province o f Alberta.Synthetic crude oil leaving the plant is a blend of two-third s gas oil and one-third naphtha. The two streams combine in a pipeline and flow to Edmonton. The product takes six days to make the journey, arriving at four locations in the city Imperial's Strathcona Refinery, Gulf's Edmonton Refinery, the Interprovincial pipeline terminal and the Trans-Mountain pipeline terminal. Each Syncrude owner receives a share of oil equal; to its percentage of ownership in the project. At the present time, the oil is being utilized by Canadian refineries from Vancouver to Montreal."

Jan 1, 1983

By J. L. Craig, C. L. Edwards, M. D. Harper, J. M. Ray

The Los Alamos National Laboratory executed 19 intermediate scale cratering experiments in oil shale at the Colony Mine in Garfield County, Colorado. These experiments have led to a better under- standing of fracture characteristics and fragmentation of & - oil shale by use of a conventional high explosive. Geologic site characterization included detailed mapping, coring, and sample analyses. Site-specific geology was observed to be a major influence on the resulting crater geometry. The joint patterns at the experimental site frequently defined the final crater symmetry. Secondary influences included vugs, lithology changes, and grade fluctuations in the local stratigraphy. Most experiments, in both the rib and floor, were conducted to obtain data to investigate the fragmentation results within the craters. The rubble was screened for fragment- size distributions. Geologic features in proximity to the explosive charge had minimal effect on the rubble due to the overpowering effect of the detonation. However, these same features became more influential on the fracture and rubble characteristics with greater distances from the shothole. Postshot cores revealed a direct relationship between the grade of the oil shale and its susceptibility to fracturing. The Colony Mine experiments have demonstrated the significant role of geology in high explosive/oil shale interaction. It is probable that this role will have to be considered for larger applications to blast patterns and potential problems in retort stability in the future of oil shale development.

Jan 1, 1983

By Gerald P. Kelton

Hydrocyclones have emerged as successful classification devices In closed circuit grinding applications However, their use for ultrafine particles separation is a relatively new application For ultrafine particles separation In small diameter (51 mm or smaller) cyclones, the cyclone diameter, feed pulp density or viscosity, pressure drop, and configuration play an important role Most often commercial application of the small diameter cyclones suffers from plugging problems resulting from the presence of fibres, wood chips, paper scraps, etc This paper describes important design features of small cyclones, followed by examples of case studies of commercial application of these cyclones

Jan 1, 1983

By J. Iannicelli

High intensity, high gradient magnetic separation can economically remove weakly paramagnetic contaminants down to 0 1 micron from industrial minerals This process is employed by all waterwashed kaolin producers in Georgia where seventeen huge magnetic separators are used to upgrade this product As a result, reserves of kaolin in Georgia have been doubled Design improvements have steadily increased the efficiency of separators and reduced power consumption below 300 KW for a nominal 65 TPH unit Beneficiation of ultrafine minerals is discussed based on pilot plant results on bauxite, ball clay, calcium carbonate, glass sand, talc, and numerous other minerals Operating parameters of the process are reviewed and some alternative equipment configurations discussed

Jan 1, 1983

By J. B. Winter

The present Inspiration Consolidated Copper Company Smelter/Acid Plant complex located near Miami, Arizona, was designed and built specifically to conform to the ambient air quality standards imposed by the Federal Clean Air Act of 1971. The present plant replaced a facility which had been in operation since 1915. The electric furnace, siphon converters and acid plant complex were commissioned in May, 1974 (1). At that time, the Plant was considered to be one of the most extensively monitored and instrumented facilities of its kind in the world. Several control areas were located in close proximity to the controlled process, in addition to so-called central control rooms in the Smelter and Acid Plant. The control rooms were staffed with officials below the foreman level. Instrumentation consisted of conventional analog devices, except for a computer used in monitoring ambient air environmental conditions and limited use of programmable logic controllers. The harsh service conditions prevalent in the plant rendered a significant portion of the instrumentation unreliable and, in many cases, inoperable. Failure of the facility to obtain the total sulfur collection for which it was designed was, in part, due to serious inadequacies in control system logic and sulfur recovery averaged 79% in the early years. After careful study of the smelting process, engineering hardware and high labor cost inherent in the organizational structure, management made a judgement decision to convert to centralized control of the process with high level supervision 24 hours per day. A distributed digital control system with supervisory arid data acquisition/information reporting computers was selected to satisfy the requirement of central control. Operations are now controlled and coordinated from a primary control room in the Smelter and a satellite control area in the Acid Plant.

Jan 1, 1983

By Allan D. Fernie

Growing interest in pit crushing and conveying is evident from the many articles, technical papers, and new equipment development recently presented. Application of a pit crushing and conveying system is complex, as many factors such as mine design, production scheduling as well as initial and ongoing capital and operating costs must be thoroughly and realistically examined. This paper will address the fundamentals to be considered and review several approaches to developing a total system for a new and existing mine situation. The planning function will be outlined and operating and design criteria defined to interface the mining operation and the pit crushing conveying system.

Jan 1, 1983