Search Documents

The series of events leading to the adoption of more complex flotation circuits for coal have been reviewed. In essence, it has been concluded that ac- ceptable overall flotation recovery will only be obtained when efficient distri- bution of collector over all the component feed size fractions is ensured. The achievement of this goal is most likely to be obtained by feed classification and separate flotation of appropriate size fractions. The adoption of such a phil- osophy, however, imposes a number of process problems of both a chemical and an engineering nature. Some of these problems have been identified and possible solutions discussed. A case is emerging for the development of a new generation of flotation cells designed specifically for the flotation of classified coal and for the development of a series of novel re- agents which have the propensity to float middling particles.

Jan 1, 1984

By L. Y. Sadler

This report summarizes the findings of a 9-yr research program, sponsored by the U.S. Department of Energy and conducted by the Bureau of Mines, to evaluate refractory liner materials for coal gasifier reactors. Commercially available refractories were exposed to coal gasifier reactor environments, reproduced in the laboratory with a high-temperature, high-pressure test facility, followed by extensive postexposure evaluation. Thirty-six castable or gunnable refractories and cements and 24 refractory brick were evaluated. The behavior of castable refractories reinforced with stainless steel fibers was also examined. Gas environments that were evaluated included steam, H2, CO2, CO, and typical high-and low-Btu gas mixtures. Exposure pressures ranged from 100 to 1,000 psig, temperatures from 5000 to 1,1000 C, for periods from 50 h to 2,000 h. In some exposures, sodium and/or potassium hydroxide were introduced in order to simulate a high-alkali environment. It was found that intermediate-and low-alumina refractories produced from domestically available raw materials, rather than high-alumina refractories produced from imported raw materials, gave the best service as liner materials and that alkali attack was probably not a serious problem with most refractories. Based on the results of this program, good choices of refractory liner materials for gasifier reactors can be made.

Jan 1, 1984

By Mark R. Pettitt

After a long series of laboratory and in-mine tests, a cost- effective, mineworthy, reduced-noise auger miner cutting head was de signed, fabricated, and field-tested by Wyle Laboratories under contract to the Bureau of Mines. Compared with standard auger cutting heads, the new heads reduced noise by 10 dBA at the jacksetter's position and by 6 dBA at the operator's position. This report contains detailed fabrication instructions, including engineering drawings, that show how a standard auger cutting head can be modified to produce a reduced-noise auger.

Jan 1, 1984

A very sensitive high-speed two-colour pyrometer was built to measure the temperature of single particles of sulphide mineral, typi- cally 50 pm in diameter, as they burnt while entrained in a hot gas stream. The pyrometer has been used to study the burning of pyrite and chalcopyrite particles and has thrown light on cenosphere formation. Measured maxi- mum temperatures have been compared with values predicted by diffusion-based models. The pyrometer has also been used to study the burning of small captive pellets (2-9 mmm dia- meter) of lead-zinc concentrate.

Jan 1, 1984

By Dwain K. Butler

INTRODUCTION Characterization of a site for the prediction and simulation of dynamic events requires the determination of mechanical properties of the rock at stress/strain levels and rates and at a scale appropriate for the events and critical structures involved. The structures of interest can be on the surface, underground, or designed to impact and penetrate into the site (projectiles). Dynamic events of interest are equally diverse: seismic waves from distance earthquakes or explosions; close-in phenomena associated with earthquakes and explosions; vibrations associated with heavy equipment or machinery; and stress transients associated with impact and penetration. The complexity of site characterization depends on two factors not specifically related to the nature of the site itself: the stress levels generated by the dynamic event and the sophistication of the prediction and simulation techniques. For very high stress levels, such as occur near a nuclear detonation, and for low stress levels, such as occur during seismic wave propagation, site characterization is simplified, and often certain details of the site are not particularly important, such as shear strength variations in the case of very high stress levels. In the intermediate stress range, however, all descriptive relations are non- linear, a complete finite strain constitutive model is required, and all details of the site, such as lithology and fracture distribution, become important. The site characterization must be complete enough to support the most sophisticated prediction and simulation technique that will be applied to the analysis of the dynamic event. The procedures of site characterization are illustrated in this paper by a specific dynamic event, projectile impact and penetration, and a specific site, an outcrop of Dakota Sandstone near San Ysidro, New Mexico. The structure of interest was the projectile itself: nominally, 1.5 m in length, 0.165 m in diameter, 180 kg

Jan 1, 1984

By W. R. Marks

Computer-aided torsional analysis of grinding mill drives is defined and related to the mill design process. Equations of torsional dynamics are developed for general mechanical drives. Consideration is given three solution types - specifically the determination of undamped natural frequencies, the calculation of steady vibration amplitudes, and the prediction of transient torques during starting. Following a summary of the methods of calculating drive motor performance, the problem in making practical application of this theory are discussed. Experiences in both calculating and measuring the torsional loads on a large ball mill with dual synchronous motors are reviewed. Conclusions are drawn on the effectiveness of computer-aided torsional analysis for improving mill drive reliability.

Jan 1, 1984

In the flotation of fine particles, problems arise which do not occur with coarse-ground pulps. For example, the presence of colloidal or near-colloid- al gangue particles gives rise to ex- cessive entrainment in the froth, with reduced grade as a consequence. If the values themselves are finely dissemi- nated, the recovery usually decreases as the particles diminish in size, so a low recovery is combined with poor grade. Sutherland and Wark (1955) referred to the complications arising from the presence of fines, indicating (p.382) that fine grinding "introduces diffi- culties that have not yet been satis- factorily overcome". At the time of writing, very little work has been done on fines flotation specifically, yet the groundwork has been well laid. The availability of better scientific instruments, together with the general advance of understanding in a wide variety of relevant research fields, has taken us a long way toward finding the reasons behind the problems as- sociated with fines, and also toward finding practical solutions. It would be useful to define what is meant by "fine" particles before going further. To some extent, the definition is somewhat elastic as far as flotation is concerned, because the density of the particles has a bearing on whether or not they act as fines. But in general we are dealing with particles less than about 20 pm in Diameter.

Jan 1, 1984

By Larry L. Wischhoefer

The Automated Breathing Metabolic Simulator (ABMS) is a versatile machine capable of performing almost any physiologically appropriate respiratory simulation. The first ABMS was delivered to the Bureau of Mines by IBM in 1973. Since then efforts have been made to refine the systems and components which make up the ABMS including the Breathing Simulator Module (BSM), Gas Analysis Module (GAM), and Supervisory Controller (SC)-each of which are also capable of stand-alone operation. Since September 1980, Reimers Consultants has been testing and modifying the ABMS and its components in order to improve the equipment and to develop simulation criteria and parameters. Changes have been made to the Phase I Design Plan and Performance Specifications; future improvements based on current experience are recommended; and test results of full scale testing conducted by Reimers Consultants in November 1983 on several types of breathing apparatus are reported and illustrated.

Jan 1, 1984

By R. H. Goodman

The development of techniques for separating minerals based on differences in their specific gravities is reviewed and their present applications in process technology outlined. Special emphasis is placed on the development, in Australia, of new models of the spiral concentrator. The mechanics of separation of spiral separators are stated, including the effects of operating parameters, Some of the traditional areas of spiral application are described, together with examples of new applications such as treatment of fine alluvials and tailings, separation of liberated minerals at coarse sizes and fine coal recovery.

Jan 1, 1984

By A. B. Parsons, P. G. Howes

"This article discusses how recent changes in the federal and Quebec .income tax laws have contributed to an improved investment climate for mineral exploration in the Province of Quebec. Individual investors who are resident in Quebec and who are in the highest tax bracket (1984-60.4% marginal rate) may obtain tax benefits that result in only nine cents of each invested dollar being at risk.IntroductionIn a recent submission by the Mining Association of Canada to the Royal Commission on the Economic Union, it was stated that the mining industry ""is no longer discovering and opening new mines at rates sufficient to offset the depletion of existing orebodies and to maintain pre sent output"". With world metal prices still in a depressed state following the prolonged 1981-82 recession, moreover, the continuing success of Canadian mining in world markets will depend on this country's ability to compete in a new environment characterized by subsidized Third World production . For the most part, this new competitive environment will encourage the development of cost-efficient mines that are better equipped to withstand the troughs and valleys of international metals prices."

Jan 1, 1984

By T. Krauthammer

A combined numerical approach is proposed for the analysis of rock-liner interact ion in tunnels under the effects of severe dynamic loads. The method is based on employing finite element formulations which describe the linear behavior and incorporating it into a finite difference code which can describe the behavior of a jointed rock medium. This method can be applied for the analysis of tunnel systems in rock, and for studying the requirements for adequate support of the tunnel.

Jan 1, 1984

By T. W. H. Parker, S. B. Sadleir

ABSTRACT A comprehensive program of air flush core and reverse circulation drilling, trial mining and beneficiation test work was carried out in 1980-1982 to re-assess the potential of the Mitchell Plateau bauxite deposit. The results generally confirm previous work by Amax Corporation. The bauxite is a medium available alumina and reactive silica deposit which responds well to wet screen beneficiation. High grade pockets have developed locally, with the potential for refractory grade extraction. A major feasibility study of the Mitchell Plateau bauxite deposit was completed in 1983. Due to the unexpected severity of the downturn in the alumina market, development of the project has been deferred.

Jan 1, 1984

By A. L. Senkayi, L. R. Hossner, J. B. Dixon, J. S. Ahlrichs

Chemical and physical properties of soils and overburden materials must be evaluated prior to strip mining activities. This information can be used to assess whether subsurface overburden can be equal in quality to the native soils, especially when these soils are classed as prime farm lands. In northeast Texas, lignite primarily occurs in the Calvert Bluff formation which is underlain by the Simboro and Hooper formations. These formations are in the Wilcox group (early Eocene). The Carrizo formation, that unconformably overlies the Calvert Bluff formation, consists of thick layers of sand with poor water and nutrient retention capabilities. These materials are least suited for placement on the surface of reclaimed land. The oxidized, medium textured overburden of the Culvert Bluff and Simboro formations possess adequate water and nutrient retention properties and are better suited for sustained plant growth when compared to the existing native soils. Non-oxidized Calvert Bluff and Hooper sediments generally have acceptable properties for reclamation although acid forming sulfides occasionally occur. Materials high in sulfides must be buried during mining or appropriately treated prior to reclamation.

Jan 1, 1984

By D. Mraz

"In certain instances, rocks around underground excavations behave as a plastic mass. This paper offers several solutions to predicting the mode of plastic flow around cavities and designing mining pillars where plastic conditions exist.IntroductionWhen stresses around underground cavities exceed yield limits of the host rock, the material often behaves as a plastic mass. The best example of this phenomenon is the behaviour of salt rocks in deep salt and potash deposits (more than 500 m deep).However, many other soft rocks exhibit similar properties. For example, Jeremic(1) described certain types of coal yielding plastically under high pressure. Alder suggested that granulated rock behaves plastically.The object of this paper is to propose a de sign procedure for mining pillars exhibiting plastic flow due to the combination of rock properties and in-situ stresses.Prandtl(3) mathematically defined a concept of a generalized, perfectly plastic substance, not possessing the property of strain hardening (Fig. I). He had in mind, a solid with a quasi quasi-isotropic , polycrystalline structure having a well defined yield point, and he postulated that its material elements start and continue to deform plastically when the maximum shearing stress ""'MAX"" reaches a sharp limit, dependent on the mean value of the sum of the major and minor principal stresses:"

Jan 1, 1984

By Ch. J. Raub

A review will be given on the electrodeposition of Au, Ag and Pd and their technically important alloys focusing on recent work at the Forschungsinstitut. Special emphasis will be given to the influence of impurities on the behaviour of the electrolyte and the properties of the deposits, e.g. on resistance and on thermal and mechanical behaviour. The importance of C in gold and silver deposits and of H2 in Pd and its alloys at normal and high speed deposition rates will be discussed. Among Pd alloys attention will be focused on the Pd-Ni and Pd-Ni-Co systems. Comments will be made on deposition of Rh and Pt.

Jan 1, 1984

By R J. Merchant

The Hauraki goldfield is located east of Auckland in the North Island of New Zealand. It includes Great Barrier Island, the Coromandel Peninsula and the Coromandel and Kaimai Ranges as far south as the town of Te Aroha and south east to Te Puke. It has a total north-south extent of about 180 km and an area of 3000 km2. The goldfield is the most productive in New Zealand, and while production at present is negligible, the area has undergone continuous exploration over the last seven years.

Jan 1, 1984

By James F. Lemons

The potential production of cobalt from nickel sulfide deposits in Canada, from nickel laterite deposits in the Pacific Islands, and from the copper deposits of Zaire and Zambia will be a function of the cost of recovery of the primary nickel and copper products. This cost of production varies significantly for these deposits and is related to the differences in the cost of labor, energy, and supplies, to production technology, and to the grade and recovery of nickel, copper, and cobalt. This Bureau of Mines paper investigates these cost and technology differences as they relate to the cost competitiveness of the deposits in Canada, Zambia, Zaire, and the Pacific Islands.

Jan 1, 1984

By J. Weng

The equations of heat conduction are numerically solved for two kinds of artificial freezing- mechanical freezing and liquid nitrogen freezing. A two dimensional finite difference model simulating the freezing field is developed. The procedure introduces a way to simulate the effect of latent heat released when water transforms from liquid to solid. The procedure also produces a way to calculate the harmonic mean of heat conductivity used when dealing with heterogeneous material. The theoretically derived temperature distributions in frozen soil are given and compared with measured data. An analysis made on the thermal design in shaft freezing. The average temperature of frozen soil is calculated by using numerical integration. The regularity of development of frozen soil radius is revealed and given in an appropriate mathematical model.

Jan 1, 1984

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

By W. R. Boehme

The laboratory test work compares various 6 x 16 mesh activated coconut carbons using a gold standard solution of 4 ppm dissolved in sodium cyanide. The carbon adsorption rate and maximum loading are measured for different feed solution ionic contaminates: silver, copper, thiocyanate, and ferrocyanide. Conclusions are drawn that among the activated coconut carbons tested, maximum loading and the effects of specific ions varied significantly. The work presented can be applied to 6 x 16 mesh carbon selection tests and specific ion monitoring for industrial carbon adsorption systems.

Jan 1, 1984