Search Documents

By Charles E. Glass

The stabil ity of engineered embankments subjected to earthquakes has received considerable attention in the last 10 years, but most of the effort has been directed toward stability of earth dams. Based upon past performance, earthquake- induced failures on non-impounding mine waste structures will likely correspond to small, local slumps or debris slides, and their stability should be considered as an integral part of mine economic planning. As such, stability considerations should include earthquake hazard, characteristics of earthquake ground motion, dynamic slope stability, and the impact that waste-dump failures have on mine operations. Numerous techniques have been proposed for analyzing the stability of embankments subjected to earthquakes. Before choosing an analysis technique, it is worth noting two important differences between the dynamic response of waste embankments and natural slopes. First, waste embankments respond as structures having unique modes of vibration, which causes embankment motions to differ from nearby ground motion. Second, because of embankment response, accelerations can be different at embankment crests than elsewhere in the structure and occur at frequencies that do not correspond to input ground motion. Because of these factors, embankment response should be calculated prior to slope stability assessment. In this paper several analysis techniques designed to calculate slope stability are evaluated, and conventional pseudostatic techniques are shown to be inappropriate for dynamic considerations. Techniques to calculate dynamic stability should include embankment response, all characteristics of earthquake motion, and roughness along failure planes as input, and should provide a displacement time-history of the slide mass as output. Two techniques satisfy this criterion, and in this paper the LADRS technique is recommended for its versatility and simplicity.

Jan 1, 1985

By J. D. Decker, T. E. Norman

Introduction Grinding is the reduction of ore and similar raw materials to particle sizes below the practical limits of commercial crushing ma¬chines. This size is about 36 in. (1 cm), in most cases, although some finer crushing machines are in regular use. The feed size to grinding machines may range upward to S in. in rod mills, and 12 in. or more in autogenous mills. The finest particle sizes produced in mineral processing operations result from grinding. Ordinary grinding of brittle materials is the result of impacting, rolling, and abrasion of heavy bodies, moving freely under the influ¬ence of gravity. These falling and rolling grinding bodies, which are usually of metal, must be much heavier and larger than the ore parti¬cles they break. This weight relationship is usually in excess of 100: 1. The sustained fall of the grinding bodies is obtained by placing them, together with the rock particles they grind, in a rotating drum or cylinder with horizontal axis, called a tumbling mill. The mill is nearly half full of grinding bodies and ore particles, which may be fed into one end and exit from the other through hollow trunnions which usually serve as the mill bearings. The mill lining must be thick to absorb wear and rough to prevent excessive slippage of the charge. The breakage of brittle rock or ore is accomplished by compression. The compression may be a rapid impact, from the fall and roll of a grinding ball, or it may result from the relatively slow and constrained motion as in a jaw crusher. Breakage by shear is a secondary result of the compressive motion. Ordinary rock has an extremely heterogenous structure with innumerable zones of weakness in which cracks, fractures, and breakages can form. When a rock is subjected to com¬pression it deforms. If the compressive force exceeds a certain critical value an incipient crack appears in the most fragile zones of weakness. This crack tip may first form on the particle surface or in its interior. When the first crack tip forms the compressive stresses immediately surrounding it flow to it, and this concentration of forces extends the crack and splits the rock. Other adjacent cracks may form during this extremely rapid process. Because of the nature of brittle particles, the work done in breaking them consists essentially of the work input required to compress them to the point at which the first crack tip forms. Breakage requires no appreciable additional energy input be¬yond that required for the deformation, since the stress energy already imported to the rock flows to the crack tip and extends it to breakage. Types of Tumbling Mills The general term tumbling mill includes the rod mill, ball mill, pebble mill, autogenous mill, and tube mill. It is of cylindrical or cylindro-conical shape and rotates about its horizontal axis. Rotational speed, liner type, and size and shape of tumbling media are selected to provide the desired operating conditions for the specific grinding application. Openings are provided through the mill ends for feed and discharge of the material being ground. A common feature of tumbling mills is the use of tumbling media

Jan 1, 1985

By Henry N. McCarl, Gary Waters, William A. Vogely

INTRODUCTION In the past three decades, world trade has grown from less than $100 billion per year in the years following World War 11 to slightly more than $300 billion in 1970 and over $2,000 billion in the early 1980s. Adjusted for inflation, the real growth of world trade in 1972 dollars increased from less than $175 billion per year in the early 1950s to slightly more than $342 billion in 1970 and almost $700 billion per year by the early 1980s. Thus trade as a whole has increased a little more than twofold in real terms in the past decade." Mineral commodities constituted approximately 20% of the value of total world trade in 1970, and significantly more than that proportion in terms of physical volume. By 1980, de- spite rapidly rising petroleum prices, mineral commodities accounted for roughly 18% of the total value of world trade. Crude oil alone ac- counted for about 16%, making it the single most important commodity in international trade. The worldwide recession of 198 1- 1983 brought a dramatic decline in both volume and price of crude oil, shrinking the impact of mineral commodities to roughly 10% of the value of total exports, worldwide, in 1982- 1983. The decline of mineral commodities as a pro- portion of the value of world trade in the decade 1970- 1980 is due largely to the increasing importance of manufactured goods and consumer products such as automobiles and electronic items. During this period, mineral commodity trade expanded roughly sixfold in terms of current dollars to an estimated $350 to 360 billion in 1980. This was equivalent to doubling the real value of mineral commodities in international trade in the 1970- 1980 period in constant dollars. The U.S. Bureau of Mines has expanded the traditional definition of mineral commodities to include semifinished products such as iron and steel (in addition to iron ore), refined metals such as copper, lead, zinc, aluminum, and tin, concentrates, scrap, and petroleum products. Since large quantities of essentially mineral derivatives travel in this form, it is reasonable to use these expanded definitions in stating the role of minerals in world trade. Thus minerals in world trade comprise 30 to 33% of total export trade in all commodities during the period 1976- 1980 (see Table 1.3.1). In addition, the U.S. Bureau of Mines estimates the value of all mineral commodities consumed in the world (at the national level) and compares this value to total worldwide commodity consumption. By this system, mineral commodities range from 30 to 40% of all commodities consumed each year in all countries during the period 1976- 1980 (see Table 1.3.2). The growth in export trade in mineral commodities by commodity group is shown for the period 1976-1980 in Table 1.3.3. These data parallel the swings in worldwide economic activity during the same time period. By any of the above measures, minerals, especially the fossil fuels, constitute a significant proportion of both total economic activity and

Jan 1, 1985

By R. D. Schmidt

An in situ leaching geochemical simulator consisting of flow, mass transport, and graphics support programs has been developed. Two dimensional flow in heterogeneous porous media is modeled using a semi-analytic boundary integral technique. This method involves mapping streamlines to straight line segments in the complex potential plane. Leachant concentration and mineral values are modeled in this plane using the (one dimensional) potential coordinates. A fully implicit finite difference scheme is used to solve the resulting coupled system of four concentration equations. Graphical representations of streamline patterns, concentration histories, profiles and recovery curves are generated. An application of the model to uranium leaching in a heterogeneous aquifer and ore zone setting is presented.

Jan 1, 1985

By Robert B. Parsons

"A study recently completed by the Prospectors and Developers Association, assisted by the author and computerized mine models he developed, presents a strong case that present tax rules severely handicap the junior exploration company relative to the established producer. This month, Tax Notes briefly summarizes the highlights of the study and some of the Association's ideas which came out of the study.IntroductionIn the case of any industry, a particular project or investment will generally generate a more attractive after-tax rate of return to a tax paying entity than to a non-tax paying entity: the ability to shelter current taxable income with tax deductions related to the project or investment can present a definite advantage as compared to shielding taxable income in the future with the same deductions. But, this advantage is probably seen nowhere more clearly than in the mining industry where the tax rules allow for substantial up-front write-off's. Studies show that the junior mining company which is earning no taxable income currently can be seriously disadvantaged, compared to the mining company which is currently generating taxable profit and paying taxes. This is particularly disturbing when one considers the importance of the junior segment of the mining industry. One might well ask where the equity is, in a tax system which causes the junior company to look at a deposit and see rock in the ground, when at the same time the deposit represents a viable mine to an operating company. This inequity and the importance of the junior mining company have been recognized to some extent in the income tax legislation. In recent years, the expansion of the rules for deducting certain earned depletion allowances against any source of income, and changes to improve the flow-through share rules, have gone part way in helping to put the junior on a more equal footing with the operating company. But it is questionable whether or not these helpful changes to the tax rules have done enough to alleviate the apparent inequities in the income tax legislation."

Jan 1, 1985

By M. H. Kahn, F. C. Bond, K. J. Edmiston

Comminution of various materials can be achieved in grinding equipment by nipping, impact, attrition, or a combination of these actions. Pna mills also known as edgerunners, chasers, and mullers-are classified as a nipping machine. The essential features of this type of grinding machine are rollers or mullers that turn on a horizontal axis while rating on the bed of material in the pan. Ploughs are used to direct the unground material to the center of the pan. Grinding may be accomplished wet or dry. Aritres, Chilean mills, and Huntington mills are types of pan mills. Ring roll and ring Ml mills, another type of nipping machine, were developed for grinding smaller particles of intermediate hardness to product sizes of about 100 pm. They were designed to attempt to reduce the cost of similar size reduction in ball mills and have been widely used to pulverize coal for power-plant facilities. Impact Machines Grinding machines that can be classified as impact mills include: hammer, cage, centrifugal, vibratory, pin, and stamp mills. The distinctive feature of an impact mill is that it has a fast-moving part that transfers some of its kinetic energy to the material particles by direct contact so that internal stresses are created in the particles. The Reitz Disintegrator is an example of an impact mill. It has rigidly mounted hammers attached to a vertical shaft that rotates in close proximity to horizontally mounted screens. The feed pulp enters parallel to the vertical shaft, and may have a solids content of from 40

Jan 1, 1985

By F. Grant

"General *The mining experiences of the coal mining industry in Western Canada have been extremely varied, with the mining companies having to adjust their operations or fail due to the harsh economy of the country in the first part of the century. The bituminous or mountain mines had the railways as main consumers with, at times, optimism that potential steel producers would require metallurgical coal. The prairie and foothills mines mainly provided household fuels, with the fine coal sold to local thermal power plants at discounted prices. In practically all cases fuel competition was very keen, and the less successful mines ceased operations in short-time spans. Knowledge of the parameters that governed the success or failures of the past coal operations should be of value to the present and future mining companies. The initial coal mines were small and were started to supply local demand. These mines had little in the way of capital machinery, engineering, or transportation equipment; therefore the mining methods and mine plans were very simple. The first industrial-sized mines imported most of their management and mining methods from other mining areas, mainly Great Britain. It took time to change the bias of management and mining methods to the requirements of strata characteristics, with rapid closure to those mines that were slow to adapt working methods. The main markets for coal were for household fuel, thermal power plants and railways, with very few other industrial markets developed. The economy of the period was harsh and cyclic and the coal mines were affected more than most industries by these boom and bust periods. It led to the survival of the fittest or the most efficient. Due to the economy, mechanization was introduced to the mines very slowly, with the inability to sell coal fines at a profit being another reason for the delay. Manual labour with hand tools was the main means of production. The work was heavy and arduous, and the pay was based on contract coal tonnage; therefore both men and management paid close attention to details so that nonessential work could be eliminated. Mine openings were dimensioned so that coal could be loaded easily by hand and support requirements were kept to the minimum. Transporting and handling the timber supports required heavy labour; thus the most efficient dimensions were chosen to suit the strata. On the other hand, during the main production seasons the mines tried to make the strata stress work for them so that the pressure was kept on the coal face to keep the coal loose while the strata, a short distance back, was induced to cave to minimize the abutment stresses. This caused mining to be an art, using skills developed by experience with the strata. This led to the development of efficient mine layouts with the openings dimensioned to the strength of the strata and the type of support available. The lack of capital and mechanization, and the manual labour, induced the mines to correlate their service and haulage systems with their mining methods. This caused many innovations that proved very practical."

Jan 1, 1985

By Stanley G. Butcher

"Introduction Many operators in western Canada, with a background in the minerals industry, talk of ""coal beneficiation"", whereas the coal industry generally uses the term ""coal preparation"" . The sophisticated cleaning circuits and thermal drying units found in western Canada makes the term beneficiation particularly appropriate. This chapter uses standard coal preparation terminology(l,2J and assumes general knowledge of coal preparation unit processes and equipment(3,4,5). The geologic setting and mining methods of western Canada, described elsewhere in this volume, present for preparation run-of-mine coals which have particular problems. As a result the cost of preparation is a higher proportion of the total minesite production costs than in other coal fields . Preparation requirements are determined by the types of coals being produced and the markets in which they are sold. Western Canadian coals have a low sulphur content and do not require cleaning on this account. Prepared coal from western Canada has to be shipped vast distances -to the Pacific Rim countries and Ontario in particular -and the savings in transport costs justify the high costs of preparation. Factors which dictate selection and operation of the preparation processes are: i) Market specifications and coal rank. ii) Size distribution of particles and particularly the liability of coal and refuse particles to degrade during handling and processing. iii) Quantity and characteristics of the associated refuse. iv) Washability characteristics (the distribution of particles by specific gravity within each size fraction). v) Surface characteristics of the fines. vi) Variability of the raw coal. Where the product (coal or discard) has a high fines content special consideration must be given to dewatering, the removal of surface moisture, to give acceptable handle ability characteristics. In the severe winter climate of the western foothills and mountains thermal drying is necessary to prevent freezing of washed coal in stockpiles and railcars."

Jan 1, 1985

By Minoru Fujita, Ian M. Johnson

"A helicopter-borne geophysical survey was flown in 1978 over selected areas on Kyushu Island, Japan. The principal sensors were a moving source electro-magnetic system and a magnetometer. Maps of apparent resistivity were generated from the EM data. Based on the resistivity signature of known deposits within the survey areas, targets were selected for ground follow-up. Drilling of one such target in late 1980 resulted in the discovery of a gold deposit from which full production will begin in the summer of 1985. The deposit contains a minimum 120 tonnes (3.86 million ounces) of recoverable gold and is the largest in Japanese history. The deposit is in a geological setting previously unsuspected of hosting precious metal deposits. The case history suggests a preferred exploration strategy which might be employed in other similar geological environments.IntroductionThe Hishikari area is located some forty-five kilometres north of Kagoshima city, Kagoshima Prefecture, Kyushu Island, Japan (Fig. I). The area and its environs is one with a number of gold deposits which have been worked with varying results since the late 1800s. The large st deposit in terms of recovered gold is the Ohkuchi (or Oguchi) Mine (Fig . 2) which was recently closed due to exhaustion of reserves. The Ohkuchi Mine started production in 1896. A total of 22.2 tonnes (714 ,000 ounces) of gold, with an average ore grade of 13.6 grams/tonne (0.39 ounces/ton), was extracted over the Life of the mine.In an attempt to discover new deposits , the Metal Mining Agency of Japan (MMAJ) carried out a regional geologic mapping program of the area between 1975 and 1977. This was followed by a helicopter-borne electromagnetic and magnetic survey. The airborne survey was flown by Scintrex and the compiled results presented to MMAJ in early 1979."

Jan 1, 1985

By O. Forsén

In the first part of this paper is studied the behaviour of small amounts of impurity elements? in the solidification of copper anodes. In the second part the dissolution of these impure anodes in sulphate based electrolysis is discussed. The first part is introduced with practical examples, the .model of solidification of impurities during the solidification of anode copper. According to this model the solidification structures of anode copper are strongly influenced by both thermodynamic and kinetic factors. Thermodynamics determine the microstructure of anode copper, but kinetics can alter the composition of melt to such that there is formed unequilibrium structures during the solidification, especially when the residual melt is solidified. The electrolysis experiments have clarified the behaviour of impuririties in the electrochemical dissolution in sulphate. Based copper electrolysis. In this study it is widely investigated to what extent any impurity elements or oxides will dissolve. In copper electrorefining. With the aid of the electrochemtcal experiments it was possible to fulfil quantitatively the qualitative results accomplished by microstructure studies.

Jan 1, 1985

By Othon do Rêgo Monteiro Neto

[The present study has investigated the extraction of copper from a chalcopyrite flotation concentrate using an adapted strain of Thiobacillus ferrooxidans and shake flasks, tank leaching and Warburg respirometer techniques. From the shake flask experiments, the activation energy and the frequency factor have been determined to be ?ka = 59.4 kJ and A = 3.3 x 105 S-1, respectively. The temperature coefficient was found to be Q10 = 2.2 in the range of 20 to 35°C. It was suggested that the reaction mechanism of chalcopyrite leaching by T. ferrooxidans involves the formation of an activated complex. whose thermodynamic values have been calculated to be ?G? = 92.1 kJ, ?S? -148.8 J K-1 and ?H$ = 47.8 kJ. The maximum volumetric oxygen mass transfer coefficient for the reactor leaching was found to be achieved by using an optimum air flow rate of 1970 cm min l at a rotational frequency of 1000 min-1. The highest copper extraction in tank (reactor) leaching experiment was 86.8% after 17 days of leaching, while in the sterile runs the corresponding copper extraction was only 40.1%. The copper extraction was suggested to be diffusion controlled. The power requirement of the aerated reactor was calculated to be Pg = 2.02 watts. During leaching, the oxygen saturation concentration was found to be C* = 6.70 mg dm-3. Using the gassing out method the critical oxygen concentration was assessed to be CCrit 0.05 mg dm 3. From the Warburg experiments, the kinetic parameters of the Monad equation were derived with a new evaluation technique to be Vmsp = 9.0 µm3 02 min-1 mg protein-1 and K = 7.4% pulp density for the effect of substrate concentration. The order of reaction and the overall reaction rate constant were determined from the modified van't Hoff plot to be n = 0.0 and k = 1.49 p dm3 02 min-1 mg Protein -1 for the chalcopyrite concentrate oxidation by T. ferrooxidans. On the basis of this experimental work, a preliminary flow sheet has been proposed for the bioextraction of copper from flotation concentrates.]

Jan 1, 1985

By James S. Goff, Stephen J. Navin, Wesley W. Moulton

The White River Shale Oil Corporation (WRSOC) is developing a prototype oil shale facility on Federal Lease Tracts Ua and Ub located in northeastern Utah. This paper covers the successful driving of 1,525 m (5,000 ft) of dogleg downgrade decline with a 70-ton Paurat Roadheader mining machine and a conveyor muck-handling system. Ground support is with rock bolt and shotcrete; welded wire mesh is optional. The Upper Decline of 3.89 m by 8.69 m (12.75 ft by 28.5 ft) was mined through the Uinta Formation sandstones and shales in 210 days. The sandstones have a compressive strength in the 48 MPa (7,000 psi) range with a few bands of shale up to 137.8 MPa (20,000 psi). Green River Formation dolomitic marlstone with some sandstone lenses was mined in the Lower Decline 3.89 m by 5.64 m (12.75 ft by 18.5 ft) in 175 days. The Green River marlstones are tough massive formations ranging up to 206.8 MPa (30,000 psi). Roadheaders for use on steep slopes must be modified to accommodate the particular problems associated with mining downdip. The paper concentrates on the application of Roadheaders to steep slopes and the problems of mining tough materials such as marlstone. The paper also shows the advantage of using the method of excavation on long drives.

Jan 1, 1985

The Greenvale Joint Venturers, Metals Exploration Queensland Pty. Ltd. and Freeport Queensland Nickel Incorporated, use ten Herreshoff roasters, for the reduction of ground lateritic nickel and cobalt containing ores.Initially the roasting section of the plant limited production, due to high down time.The use of technology developed and adapted over a number of years has achieved significant increase in on line time and a minimization of costs.

Jan 1, 1985

By James H. Boettcher, W. Durand Eppler

INTRODUCTION In the second quarter of 1979, Rapid Mining Co., Inc. ("Rapid") inquired whether Crocker National Bank ("CNB") would provide $4 million in term loan financing to help ("Dry Creek") acquire the outstanding shares of the Dry Creek Coal Company ("Dry Creek") in West Virginia. Prior to approaching CNB, Rapid had sought financing with the assistance of a financial advisor from a number of commercial banks without success. A summary of the initial terms requested by Rapid is shown in Table 1 compared with the actual terms on which the transaction closed. It is not difficult to note that the two sets of terms differ significantly. This is often the case when financing requests based on the expectations and vision of a mine developer are juxtaposed with more pragmatic requirements of a commercial bank. The "art" and fund of structuring financing plans for mining ventures (highly leveraged acquisitions or grass roots) comes in working with mine developers to arrive at a final financial structure that meets their objectives and constraints as well as those of the bank or other financial institutions providing much of the financing. Beginning with the terms requested by Rapid and ending with the terms that closed the transaction, this article briefly describes the process we went through with Rapid Mining. The Seller and Buyer The Dry Creek Coal Company was established in 1961, after its owner acquired the coal leases from Republic Steel. Republic has mined the primary coal seam from 1948-1961. Dry Creek was owned as a subchapter S corporation (i.e., for federal income tax purposes, income is taxed at the shareholder level) and had been run on a low key basis. Since the company had virtually no debt and limited cash needs, the owner produced primarily when rail cars were available and income was required. Output was therefore erratic as is shown in the top of Table II, but the result was a profitable little company with an attractive free cash position. Because the owner wished to retire and enjoy his wealth in a more readily spendable form, he had put the mine, with stated recoverable reserves of approximately 13 million tons, up for sale. In contrast, Rapid Coal's investors consisted of a number of investors of disparate financial situations. They had agreed upon a primary objective of income maximization and planned an annual production rate of 120,000 TPA which they and the current owner believed realizable. The Formulation of a Financing Structure Figure 1 presents a simplified overview of the sequence of steps taken in the financing process which lasted approximately three months from start to finish. Since banks see many requests for funding and considerble time is required to follow up on each, an important step was determining, after a brief review of the materials provided to us, whether the basic "eonomic entity" was viable. In this case, the size and quality of the reserves, the inherent operating cost characteristics, the sales arrangements, the management/labor situation and Rapid's principles all appeared to be sound enough to warrant investing the time necessary to do a thorough analysis of the project. Once this decision was made, the evaluation and analytic process shown in Figure 2 was initiated. The first and most fundamental concern of any banker is whether the loan will be paid back as scheduled from the cash flow generated by the project. The amount of debt relative to the owner's equity is of course crucial in such a determination. Before the debt/equity issue was addressed, however, a number of more qualitative factors had to be studied and if

Jan 1, 1985

For an exploration area with a predetermined grid of data points, a construction is given for elementary blocks which subdivide the entire area without omission or overlap, and with the property that each data point is situated at the centre of its corresponding block. The construction has a useful optimal property, and more importantly avoids an error which has been made recently in more than one publication.

Jan 1, 1985

By J. M. Barker

New Mexico is the leading domestic producer of perlite, a hydrated volcanic glass that can be expanded thermally to form a white, very porous, lightweight material. The United States is the leading consumer and producer of perlite in the world (Pettifer 1981). New Mexico produced, at five mines (Fig. 1), about 86% of all domestic crude ore mined in 1984 (Meisinger, 1985). Perlite is mined in 6 other western states, ore is expanded in 33 states, and the expanded ore is consumed in all states (Meisinger, 1985). Gross value of domestic ore mined in 1984 was about $16,500,000 (FOB mine; Meisinger, 1985) with much value added by expansion and processing prior to sale to end users. In contrast to the ubiquitous nature of perlite products in the U.S. economy, facilities for testing perlite ore, expanded perlite, and perlite products are notably lacking on a commercial, cost-effective, or readily accessible basis. The New Mexico Bureau of Mines and Min¬eral Resources (NMBM&MR) established a perlite¬testing facility in 1984 to mitigate this lack and to further the mining of perlite in the state.

Jan 1, 1985

By A. W. Khair

This paper presents an analysis of respirabie dust generation due to the action of a continuous miner. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). An analysis of -400 mesh particles was done on gravity collected material. Samples of entrained dust were collected through the use of cascade impactors. Both samples were analyzed for size distribution and particle shape. Using the simulated coal cutter permitted variation of operating and in-situ parameters to provide information on the effects on generation of -400 mesh particles. In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.1 cm x 15.2 cm) were first subjected to confining pressures, equivalent to in-situ conditions. Such blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with an attached camera.

Jan 1, 1985

By David A. Zegeer

It's a pleasure to be here, and an honor to be invited to address this distinguished group of professionals. Today, I'd like to begin with an overview of progress in coal mine safety and health. I'll discuss some current areas of concern. And I'll make some suggestions as to where we may be headed in the future. This year marks the coal industry's 15th anniversary under the Coal Mine Safety and Health Act, which took effect in 1970. We have come a long way in those 15 years. As a coal mining man from way back, I remember the era when the Coal Mine Safety and Health Act first was passed. Some of you may remember it, too. At that time, the safety and health of coal miners was in the public eye even more than it is at present. One reason was a mine explosion that killed 78 miners when it occurred in a large underground coal mine in November 1968. That disaster raised tremendous public concern about protecting the safety of miners.

Jan 1, 1985

By B. S. Crocker

Introduction Pebble mill grinding can be defined as wet or dry grinding in a tumbling mill with pebbles used as grinding media instead of metal balls. To clarify the terminology, which may differ in the various mineral industries, it is essential to point out the differences between grinding with partially sized and carefully sized grinding media. When grinding with partially sized media (limited top size only), sizing is usually the setting of the primary crusher and there is no bottom sizing-all fines, chips, sand, and small sizes are included. This is often called run-of-mine or primary autogenous grinding. In this case the entire crusher discharge is fed into the mill and part of it becomes "charge" and the rest is "sand feed." When grinding with carefully sized media (i.e., media that is sized both at the top and bottom of the size range), no fines or chips should be present in the charge to the mill. This is pebble milling and the grinding media consists of ore, rock, Danish pebbles, gravel pebbles, or ceramic pebbles-media that is appreciably lighter than steel balls. The grind¬ing charge is fed to the mill to maintain a load and it does the grinding usually on a classified sand product of suitable size. If the grinding media is the same as the raw material being ground, this type of grinding is also called secondary autogenous grinding. Pebble milling was in common use in the gold mines of South Africa in the early 1900s. It is by far the oldest form of autogenous grinding. It may be used to grind crushed ores from a maximum size of about -% in. to all -10 µm. Pebble milling differs from "run of mine" grinding in many ways, but two big differences are: I) The ore itself is crushed to approximately t/4 in., or it may be further reduced to 8 or 10 mesh in a rod mill or fine crusher. 2) Then carefully screened ore of the correct size is placed in one or more stages of pebble mills to grind the ore to its desired final size. The media size is carefully selected to be the most efficient for the particular size reduction required in each stage. This is a precise practice, and pebble mills can be designed as easily and accu¬rately as can rod mills or ball mills by those skilled in the art. A pebble mill is a rotating cylinder in which the grinding media has been carefully sized for the job in hand. If the mill is doing coarse grinding, the media will be correspondingly large and the mill might be called a primary (or intermediate) pebble mill or a lump mill. If it is to do fine grinding, the media selected is proportionately smaller and the mill would be called a secondary or tertiary pebble mill. The media itself is normally rounded pebbles made from screened ore from the primary-crusher discharge. The charge could be rounded pebbles of the correct size removed from a primary autogenous mill, or the pebbles could be carefully sized gravel, sized beach pebbles, or sized flint pebbles. Usually the specific gravity of a pebble is from 35 to 55% of that of steel balls. It commonly varies from 2.66 to 4.2, depending on the specific gravity of the ore. Primary pebble mills, or lump mills, would be charged with pieces of rock up to 10 in. maximum and 5 in. minimum and would grind crusher discharge with a maximum size of 1/4 in. on hard ores and 3/8 in. on softer ores. Secondary pebble mills could be charged with pieces of rock screened on 4 x 4-in. square mesh and retained on 1 1/2 x 1 1/2 in. These mills would grind material with a top size of 8 to 10 mesh. Tertiary pebble mills could be charged with screened rock that would pass 3 x 3 in. and be retained on 1 x 1 in. and grind 35 to 48 mesh sands. Principles of Operation Media Size To operate a pebble mill efficiently it is imperative that great care be taken in screening the rock feed that is fed into the mill to round up into a range of pebble sizes that are suitable for grinding of the sands that are also being fed into the mill, having regard to the top size and the average size of such sands. Since most mill operators know from experience the correct size of steel balls to be used in a mill to handle different sizes of sand feed, it is convenient to relate the pebble size to a ball size. If the correct ball size is not known, it is relatively simple to conduct batch laboratory tests in 12- to 18-in. laboratory mills to determine the optimum size of steel ball. Also, Bond and others have published formulas for calculating the optimum ball size. When the correct size of the individual steel ball is known, then a pebble of the same weight will perform the same grinding if used in the proper size of mill and under the proper conditions, which will be defined later. This media size, as defined by the average weight of the individual pieces, is most important. The following tests will serve to clarify this point. Laboratory Tests Using Steel Balls or Pebbles. Several labora¬tory grinds were made to compare a given size and weight of steel ball with a pebble of the same weight but larger size, and of the same size but lighter weight. The following loads were used in the 12-in. laboratory mill: All 1 1/4-in. steel balls weighing 122 ± 10 g. All 1 3/4-in. pebbles weighing 123 ± 5 g. All 1 1/4-in. pebbles weighing 45 ± 3 g. To equalize capacity, the test with the steel balls was run only 34% as long as the tests with pebbles. In each case, 2,500 g of primary sands were ground at the optimum gravity for the media being tested at a speed 78 1/2 % of critical speed, and for 170, 340, and 680 revolu¬tions for the steel balls, and 500, 1,000, and 2,000 revolutions for the pebbles. The first test is summarized in Table 74 by showing the 80% passing size in microns for the feed and for each of the grinds. Two other tests are summarized in Table 75 showing the screen analyses

Jan 1, 1985

By B. H. Kaye

Particle-size Distribution Specifications for Particulates. Feed to and finished products from size-reduction operations are defined in terms of the particulate sizes involved. It is also well to know whether the ultimate individual particle is being measured, or, if any aggregation or agglomeration of particles exists, whether this has been created by the size-reduction operation. The most complete description of a powder is given by its particle¬size distribution. This can be plotted in terms of cumulative percent oversize or undersize in relation to the diameters of particles, or it can be plotted as a distribution of the amounts present in each unit of diameter against the several diameters. It is common to employ a weight basis for percentage, but there are some data in the literature where frequency, or number of particles, is used. The basis of percent¬age, whether weight, frequency, or some less commonly used factor, should be specified, as also should be stated the diameter, its units, and preferably whether determined by sieve, settling velocity, or other¬wise. Fig. I presents two sets of distributions-ore cumulative and the other in unit intervals. The slopes of the 5-µ intervals of the cumulative curves are converted to percent per micron and plotted as a block, or histogram, from which smooth curves are derived. Powder A has a narrower, or tighter, size range for the bulk of its weight than powder B. Both materials have the same weights below and above the size marked by the arrow. Simpler treatments of distribution are possible. In some cases the significant value is the top size. Since the 100% point is dubious, some amount, as 95 or 98%, so specified, can be called top size. In other cases the percent on some sieve helps define coarseness. Merely stating that all, or all but a small percentage, passes a given sieve is inadequate for defining the true fineness or a material. Complete parti¬cle-size analysis to show the distribution is essential for most compari¬sons and calculations. Particle-Size Equations. A number of equations have been pro¬posed to correlate the quantity of a particulate material with its parti¬cle size to obtain a distribution relationship. 's 19 In the literature it is often assumed that a powder must follow some distribution, such as the Rosin-Rammler-Bennett:20, 21

Jan 1, 1985