Search Documents

By Euclid P. Worden

INTRODUCTION Today, conventional raise boring is an accepted method of development in underground mines and on major construction projects. Over the years that this technique, and its associated machines and tools, have been under development, many articles have been written on the subject. To a great extent, these papers have reported operating results of one or more specific projects or have been generalized reviews of state-of-the-art machines and tools. This paper is intended as a review of the technique from an operational standpoint. Conventional raise boring, as opposed to the related variants box hole drilling and underground blast hole drilling, is a two step process consisting of the pilot hole drilling and reaming cycles. This author has covered the subject of pilot hole drilling in another article (1) . A good review of the current machines and equipment has been presented by Monroe (2) and an overall review of this entire technology was published by E&MJ (3) and Mining Journal, April, 1983 (4) . The subject of the reaming cycle is presented here together with some of the technical aspects of how the drilling tools are intended to be used. OPERATIONS Bit Change After the pilot bit has broken through at the end of the pilot hole cycle, a changeover takes place at both the machine and

Jan 1, 1985

By G. E. MeGlelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores. This technology has been adopted on a broad scale by the precious-metal-processing industry. This report presents information on the application of agglomeration technology to finely ground precious-metal-bearing tailings. Two commercial operations that have benefited from agglomeration technology are discussed. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1985

By R. J. Sweigard, R. V. Ramani

Demands on available lands will continue to increase due to the projected population increase and industrial expansion. Though there is an upper limit on available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as nonrenewable and renewable. Lands with minable resources can be dedicated at some Point to the extraction of resources. Such a dedication, however longterm, is only temporary because of the nonrenewable nature of the minable resources. The land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no nonrenewable uses are preempted and no renewable uses are permanently destroyed. This paper addresses primary aspects of this planning process. These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning, and a long-term plan for resource conservation and utilization. Minerals, with agriculture and forest products, are the primary sources of wealth. Therefore, to amid land development that may preempt future mineral resource utilization, local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more land use planning is needed for lands with mineral deposits.

Jan 1, 1985

By R. D. Hansen

This paper discusses the influence of frother type and dosage on recovery/selectivity in coal/sulfide mineral flotation as a function of particle size. It is shown that different frother structures do exhibit quite different but consistent performance characteristics depending on the underlying particle size ranges involved as well as the dosage levels of both the frother and collector. The data presented on existing commercial frothers end some new special purpose experimental frothers is used to illustrate some general operator guidelines on proper frother selection and use.

Jan 1, 1985

By J. Aiello

"Introduction Byron Creek Collieries Limited Corbin mine is located in southeastern British Columbia approximately 180 air kilometres southwest of Calgary (Fig. I), twenty four kilometres south of Highway No. 3 via a newly constructed provincial road (Fig. 2). The development of the area began July 30, 1905, when D.C. Corbin, a prominent businessman from the northwestern U.S., and his associate E.J. Roberts first visited the site of Coal Mountain on horseback. Coal was in great demand by railways and other industrial users, so the Corbin Coal and Coke Co., after acquiring 6,000 hectares of land in the area, began to develop a mine. Mr. Roberts was responsible for the construction of the 22-kilometre rail spur, the Eastern British Columbia Railway, which joined the mine to the CPR main line at the McGillivray Loop. Rail access to the mine and its developing community, Corbin, B.C., was completed in September 1908, the same year that the first underground mine began production. The Corbin Coal and Coke Co. operated six mines on Coal Mountain (Fig. 3) and production from 1908 to 1930 inclusive totalled 2,120,800 tonnes. This production was allocated to the mines as follows:"

Jan 1, 1985

By J Edmund Hay, Harry C. Verakisl, Richard J. Mainiero, John J. Mulhern

As the first stage in the rulemaking process, MSHA prepared requirements for the approval and use of permissible explosives and blasting items in underground coal mines. These draft requirements known as "preproposals" were announced in the Federal Register in mid-1984. The draft requirements on the use of explosives were written as a revision to Title 30, Code of Federal Regulations, Part 75, Subpart N. The draft requirements for approval of permissible explosives including sheathed explosives for unconfined applications, approval of water stemming bags, approval of detonators and approval of blasting machines were prepared as Parts 15, 16, 17 and 25 respectively.

Jan 1, 1985

By Felipe De Lucio Pezet

El presente texto describe la importancia del oro como metal precioso -en tanto sus propiedades permiten que se lo convierta con facilidad, pulverizar y se lo vuelve fundir, a diferencia de otros metales que requieren de instalaciones complicadas para extraerlos. Asimismo, su distribución es homogénea ya que sus yacimientos no están concentrados en pocos países como sucede con el cromo o estaño. De otro lado, el brillo, color y la forma de esta metal genera una belleza particular entre los hombres. En cuanto su uso en la minería , solo una séptima parte es industrial o cotidiana, mientras que el resto es guardado en las bóvedas del banco. Finalmente, la producción del oro en el Perú proviene de una cuarta parte de los lavaderos de Madre de Dios y de una quinta parte de la fundición de La Oroya que lo rescata al fundir minerales de muchas minas que tienen el oro como subproducto.

Jan 1, 1985

By Michael Ferrell

The primary reason pigments are used in plastics is to impart a desired color to the plastic. Color is one of the more important assign considerations associated with today's market oriented society. Secondary reasons for adding pigments to plastics include: 1. Improved UV stability 2. Enhancement to selected physical properties 3. Changes in optical properties Pigments may be used at loadings as high as 20% or as low as .001%. Generally the loading levels are between 0.2% and 2.0%. Pigments may be added to the plastic either by the manufacturer of the plastic, or by the user of the plastic. If the customer buys material that is already colored, it is referred to as "pre-colored". If the customer buys uncolored plastic and adds colorants, the process is referred to as "in-house" coloring.

Jan 1, 1985

By Weibai Hu

The flotation separation of wolframite from fluorite and quartz is investigated with chelating agents and neutral oil as synergic collectors. Test results indicated that a-nitroso-ß-naphthol has a strong collectivity for wolframite and selectivity against fluorite and quartz. The 8-hydroxyquinoline has collectivity and selectivity also. They both have a better activity than sodium oleate. However, the cupferron is slightly inferior. The synergism of chelating agents and neutral oil looks promising, especially for fine wolframite particles. The activation effect of Fe2+ and Ca2+ ions on separation of wolframite from fluorite and quartz is slight. The UV absorb-spectra measurements showed that the adsorption of chelating agent on wolframite is multilayer, and flotation behavior is related to chemisorption. The chelating agent which bonds to Fe and Mn sits on the wolframite surface, and the reaction between Mn2+ ion with collector is more significant. The essentials affecting reagent activities are the bonding factor and the hydrophobic factor. These factors are discussed by structure-activity relationship theory. The synergism of neutral oil is a secondary collector likely to lengthen the hydrocarbon chain of chelating agents.

Jan 1, 1985

By C. Hertzler

The difference of means of milling characteristics by rock and ore type is tested in a statistical manner in the paper. The null hypothesis being tested is that the sample means of two different populations are equal. It is assumed that the null hypothesis is true when performing the test. Because of this, acceptance of this hypothesis leads to the conclusion that the sample means of the two different populations are equal (or there is no significant difference between the sample means), not that the samples come from the same population, as the author asserts. Rejection of the null hypothesis leads to the conclusion that the sample means of the two different populations are not equal. A P value for this test is reported in Table 2 and is incorrectly identified as the probability that the two samples came from different populations. Actually, what was recorded was 100(1 - p) where p is the usual p-value. The usual p-value measures, on a scale of zero to one, the extent to which the data agree with the null hypothesis. It is the probability of observi" a value of the test statistic (Z score) that is at least as contradictory to the null hypothesis as the one computed from the sample data (McClave and Dietrich 11, 1982). The author makes no mention of the fact that were these tests to be conducted together, the chances of determining that the null hypothesis is not true when it is really true are increased considerably (Snedecor and Cochran, 1980). This is a multiple comparisons problem and should be dealt with accordingly. The usual methods involve adjusting the level of the individual tests. Table 2 reports an incorrect 100(1 - p) value in the comparison of concentrate grades for other rock types with .30 to .69% Cu vs other rock types with .70 + % Cu; 86% should be 98.6%. Although the article can be criticized for poor data presentation and discussion of that data, the point the author makes regarding the use of these statistics in the ore reserve estimation process is well taken. It does not appear that inaccuracies in the statistical interpretations have hindered that usefulness.

Jan 1, 1985

By W. W. Muir

"The Baker Mine used a 100-ton per day conventional cyanide leach mill located in northern British Columbia. A production decision was made in early 1980 and the mill was on fine in April 1981.Ore reserves had been estimated at 100,000 Ions averaging 0.9 oz gold per ton and 18 oz silver per ton . Mineralization consists of electrum (Au/Ag) and acanthite (Ag2S).This paper will review plant design and focus on some problems associated with start-up and early operation with the intention of assisting other mine operators by indicating potential problem areas.IntroductionThis paper will discuss operating strategies employed at Baker which improved over-all mill performance. Also included are some ideas which could be steps toward a more efficient operation in a similar setting.Actual dore production by mine life was 37,606 oz gold and 742,117 oz silver.Figure 1 illustrates the relative stability attained over the mine life. Metal recoveries for gold and silver were 92% and 85% respectively.Safety at Baker was of prime importance because of its remote location. Baker received the Mine Safety Association ""Small Mines Award "" in two of its three operating years. At shutdown in late 1983 the mill had operated for over 850 days without a lost-time accident."

Jan 1, 1985

By Russell Clough

The Pacheco Pumping Plant is situated on the west end of San Luis Reservoir in western Merced County, California. It is designed to draw water from the reservoir and pump it into a 3,500,000 gallon regulating tank. The water then flows entirely by gravity to the Coyote Pump Station in Morgan Hill, a distance of 40 miles, where it is pumped into Anderson Reservoir. This water is used to recharge the depleted groundwater table in the Santa Clara Valley. Eventually, some of the water will be diverted to Hollister in San Benito County and to Watsonville and Santa Cruz in Santa Cruz County. The owner is the United States Bureau of Reclamation. The underground work consisted of a fifteen foot finished diameter surge shaft 250 feet deep to the crown of the pump chamber; a twenty foot finished diameter pump chamber which declined from the shaft at 14.2% for ninety feet and then ran horizontally for 180 feet; and twelve each five foot diameter steel lined intake shafts 240 feet deep which intersect the pump chamber in the horizontal section. (Figure 1) Upon completion of the pump chamber, the contractor had to dewater the existing tunnel under the reservoir, excavate the remaining fifteen foot plug, and concrete the transition. The low bidder for this contract was Underground - Continental-Heller at 414,456,000. Excavation of the open cut for the pumping plant and surge shaft began on April 14, 1983. This was performed using a Koehring 1066D backhoe, dozer, trucks, and two Cat 631 scrapers. The excavation was started at the surge shaft so that the grouting could begin

Jan 1, 1985

By Newell RB

Grinding circuits are used in most mineral processing plants. Their widespread application makes the efficient running of the circuits essential to almost all resource projects. This paper will show that, with the application of modern multivariable control techniques, improved plant performance can be obtained when compared with conventional single loop control strategies. Results are presented for a simulated closed-circuit ball mill.The grinding circuit was controlled using the rod-mill water and primary and secondary sump dilution flowrates as the manipulated variables. Variables controlled were the primary cyclone feed flowrate, the primary cyclone feed density and the particle-size measurement (percentage smaller than 75 um).

Jan 1, 1985

By M. U. Özbay

A series of blasting experiments was carried out in an up-dip stope of a gold mine using short-perioddelay electric detonators. The main object of the investigation was to show the interactive effects of short-delay blasting. The delay range over which observations were made was restricted to between 10 and 200 ms. To quantify the blast results, data were collected on fragmentation, throw, position of muckpile, and ground vibration. For comparative purposes, blasting parameters for conventional pyrotechnic sequential firing were also measured. The paper describes the most relevant parts of the study and gives the experimental results. The interactive effects of short-delay blasting are analysed, and some aspects of the breaking mechanism are discussed.

Jan 1, 1985

By K. A. Natarajan

Microbe-mineral interactions in the leaching of complex sulfides are discussed with respect to (a) role of galvanic interactions in selective dissolution, (b) bacterial attachment to sulfide mineral substrates and (c) the utility of specially adapted metal tolerant bacterial strains. Experimental results obtained in the leaching of two types of complex sulfides, namely, a lead-zinc-copper sulfide and a copper-nickel sulfide are illustrated.

Jan 1, 1985

By Pat C. Hautala, J. R. Hoskins

This is a new era for the minerals industry. Never before has there been more need for effective communication. So said Robert Anderson, chairman and chief executive officer of Hanna Mining Co. He was speaking to the American Mining Congress's Communication Workshop. The question is whether there is enough industry concern to meet the challenge. Anderson observed that increased workshop attendance, in continuing tough times, reflects the industry's concern for communication. But, why were students, faculty, engineers, supervisors, and managers not at the conference? Communication applies to every manager, Anderson said. But he was the only operating manager present. And only one company sent operating supervisors. The remaining conference participants were public relations personnel, generally with nonmining backgrounds. And the program dealt mostly with public relations issues. Role of Communication in the Minerals Industry. It is well known that the minerals industry faces economic, political, and social problems. Economic shifts and foreign competition have created an international minerals industry and an international marketplace. This, in turn, calls for worldwide communication. Other factors effecting communication are: • Governmental protectionism as well as regulatory reforms call for increased interaction with governing officials. • Changing social values have created environmental issues and anti-industry attitudes. This intensifies the need for improved public relations. • Traditional work values are shifting towards self-actualization and humanistic movements. The work force is better educated and more informed. Employees demand more satisfaction, equality, and job autonomy. • The mining industry's task of managing its human resources is complicated by layoffs, job uncertainties, and bleak outlooks concerning employee morale and motivation. Technology and Information for a New Era As noted, this is a new communications era, one propelled by technology and information. Technology has led to reduced demand for raw materials by developing substitutes. Copper demand, for example, will never fully recover. Copper cables are replaced by fiberoptics; copper transmission lines, with aluminum. Technology has shifted the US from traditional to high tech and service industries. The speed, frequency, and scope of information transmission have greatly increased. But the most significant characteristic of this information is not the pace of advancing technology. It is the dramatic increase in the importance and frequency of our personal transactions. Knowledge has replaced raw materials and capital as the strategic resource. Information has replaced energy as the transforming resource. And the game against nature has become an interpersonal game (D. Bell, Post-industrial society, Physics Today, '76). In Megatrends, John Naisbitt says that information will soon double every 20 months. So, professionals will become "information workers." And communication will be the life channel of the information age. Thomas Wolfe said you can't go home again. Hanna Anderson said we are, indeed, facing a new day. It will never again be "business as usual." We must move into the information age with the rest of society. We cannot trust that the world will continue to rely on our products. Nor can we place the responsibility and control for problems and solutions outside the minerals industry. Improved communication is not a panacea. But, Anderson said, it is critical to the minerals industry. What is Communication? The word communication is overused. It is applied to every aspect of our lives. Satirist Tom Lehrer got sick of hearing about the need to communicate. He said, "It seems to me that if someone is having all that trouble communicating, the very least he can do is shut up!" Obviously, we cannot follow that advice (though we might wish that some others would do so). Communication is always going on. It is inevitable. Yet we have many misconceptions about com-

Jan 1, 1985

By G. P. White, J. M. Jones

Introduction Computer simulation is a technique that has been around for many years. Its applications include designing steel mills, planning space shots, or even developing ways to beat the casinos in Las Vegas. However, the use of computer simulation in surface coal mining is fairly recent. To promote its use, several government agencies, including the US Bureau of Mines, Forest Service, and Department of Energy, contracted with universities and private companies to develop computer simulation programs for surface coal mining. Some of these developers include McDonnell-Douglas Electronics Co., Pennsylvania State University, Montana State University, Fluor Mining and

Jan 1, 1985

By J. O. Pitts

"Background The preponderance of Canada's coal resources is located in areas remote from high demand domestic users and at some significant distances from deepsea ports. This places great demands on the transportation system and has forced the coal and the transportation industries to adopt highly efficient methods of handling the product and hauling it to market position. Most of the coal not consumed in minemouth thermal power stations is carried by rail over lines operated by the two transcontinental railway systems, Canadian National and Canadian Pacific. These rail networks are extensive and have the advantage (as compared to most other North American railways) of being able to handle coal movements from origin through to destination without interchange to other rail carriers. Coal SourcesWith exception of the coal produced in Cape Breton, Nova iScotia, all the significant shipping volumes in Canada emanate ifrom mines located in the three most westerly provinces. Figure I ishows the geographic distribution of the major mining operaitions shipping coal to domestic and export markets. The prinicipal routes and the tonnages carried (1980 calendar year) are ialso indicated. iThe 1980 shipping data are summarized in Table I. Saskatchewan lignite began moving from Bienfait to Thunder Bay by CP Rail unit trains in mid-1981 at the rate of one million tonnes per year. The product is handled through Thunder Bay Terminals and delivered directly to a nearby Ontario Hydro electrical generating station."

Jan 1, 1985

By J. W. Mustard

The Macmillan Pass tungsten property (MacTung) is the largest known copper-tungsten, calcic, exoskarn deposit in the Western Hemisphere. Located on the border between the Yukon and Northwest Territories in northwestern Canada, the deposit crops out on Mt. Allen within the Selwyn Mountain Range. It was discovered in 1962 by a subsidiary of AMAX Inc. and has since been explored by 16,300 meters of surface and underground diamond drilling and by 800 meters of underground development. Geologic reserves are in excess of 30 million tons, grading slightly less than 1.0% WO3. Scheelite (CaWO3 ) is the main mineral of economic interest. Accessible by road, the property is not in production. Previously estimated reserves at MacTung have been unable to fully utilize all the geological controls on mineralization. In the past three years, however, an intensive program has been underway to improve our understanding of the deposit and to use the resulting information in a more precise way. This paper will discuss the key aspects of the geology as they specifically relate to reserve estimation and will demonstrate how these controls are being used in a geostatistical model of the deposit.

Jan 1, 1985

By G. T. Lineberry, L. Adler

Reduced clearance a one of the most important characteristics of encumbered space in underground coal mining. Another key variable is the maximum velocity at which a piece of mobile mining equipment can operate in this limited space. Typical velocity-clearance curves for different mine transportation systems are developed and characterized. Applications of the relationships are examined, emphasizing their significance in designing and controlling mine materials handling system.

Jan 1, 1985