Search Documents

By John W. Rushton

THE PLANNED MAINTENANCE PROGRAM All concentrators should start with a planned maintenance program from day one. Every- body thinks they have a program in place before start-up, but in reality, most have only a fraction of what is needed to avoid the "Post Start-up Disaster" (PSD) - two years for start-up is not that uncommon. An effective program has all of the following: (1) Good people. (2) Area Maintenance. (3) Good PM Checklists. (4) Daily Work Schedules. (5) Written Work Orders. (6) Equipment Histories. (7) Backlog Control. The installation of a workable program takes hard work, talent, and commitment. You have to know what you are doing (hard work will not replace talent). Good People Good people are available in any location if you make the effort. Always check references carefully (both superiors, peers and subordinates). Was the last concentrator they worked at successful? Was it clean? Find out! Success or failure follows people around. I know people who are experts on PSD because they have lived through it three or four times. You need some college trained people with hands-on experience. There are no secrets, you have to make the effort. If you make a mistake in hiring (and you probably will), make the tough decision necessary to rectify it quickly. Area Maintenance Area maintenance refers to organization of supervision such that one person is uniquely accountable for every inch of ground and piece of equipment. Avoid overlapping authority if at all possible. You must have a planner as a staff position. A foreman cannot effectively plan and

Jan 1, 1986

By P. Massacci

This study deals with the development and utilization of computer models for evaluating the extent to which variability of raw material grades can be reduced from the deposit to the processing plant. The specific case of a cement works is examined. The deposit and the elementary quarring operations were modeled for the medium and long-term planning of production with the objective of predicting grade variability of the flow stream in time. The feeds inferred from previous modellings were used for simulating storage operations. In particular, the storage process (linear stockpile, as an alternative, blending from various heaps) was modelled in order to select the main parameters of the process to minimize grade variations of the feed to mill. The ways followed for modelling the prehomogenization process are described. The homogenization performance and efficiency in the silo stage has also been studied and an estimate made of the distribution of residence time on the basis of input and output sampling.

Jan 1, 1986

By D M. Menne

This paper is intended to give a general review of current gold extraction technology for free-milling or non-refractory auriferous ores. Fundamental process concepts and some of the differences between the current technologies is referred to. Typical flowsheets and layouts are provided and it is demonstrated that technology for extracting free-milling gold is relatively simple. For environmentally sensitive areas such as encountered in New Zealand relevant cyanide decay and destruction technology is also discussed. Brief mention is made of some likely future innovations. Finally reference is made of New Zealand's previous significant contribution to gold extraction technology. These contributions were pioneering ranging from the cyanide leaching of gold to adsorption by carbon and precipitation by zinc. New Zealand has not allowed its potential gold projects to develop at a rate commensurate with the rest of the world thereby stifling its renowned innovative approach in this technology. It is time for New Zealand mining to recognise its unique opportunities in developing gold extraction technology and again take a rightful place in leading the way.

Jan 1, 1986

By Guy G. Jr. Granger

INTRODUCTION Due to the current depressed state of the mining industry, many mining companies have been forced to operate at less than maximum capacity. This paper will describe how the AMAX Henderson Molybdenum Mine and Mill near Empire and Parshall, Colorado respectively have utilized operations scheduling and budgeting to achieve production targets at minimum operating costs The AMAX Henderson Molybdenum Mine and Mill have been operating most recently at approximately sixty percent of maximum capacity. OPERATIONS SCHEDULING Production Targets. The production targets are tons, operating days, tons per opera- ting day, head grade, recovery, and pounds of molybdenum. One specific objective of operations scheduling is to meet the production target for pounds of molybdenum. Present market conditions dictate that production be adjusted to match sales of molybdenum. Over-production and creation of molybdenum inventories is unacceptable. In summary, the product ion target for pounds of molybdenum must be met, but not exceeded. Capacity. The AMAX Henderson Mill single stage open crushing circuit capacity is 48,000 dry short tons per day. The AMAX Henderson Mill single stage semi-autogenous primary grinding mill circuit capacity is 38,000 dry short tons per day. All other AMAX Henderson Mi 11 circuits such as rougher flotation, regrind, cleaner flotation, lead leach, filtering, drying and concentrate handling are sized to accommodate the 38,000 dry short tons per day and pro- ducts from same. The tailing delivery system is designed to accommodate tailing from a 38,000 dry short tons per day operation. Constraints. One mill production scheduling constraint is that the mill operating schedule must be the same as mine production, ore haulage and crushing. There is a total crushed ore stockpi1e storage capacity of 240,000 dry short tons. This breaks down to 60,000 dry short tons of crushed ore over the three reclaim pan feeders for each of the four primary grinding mill circuits. However, there is only approximately 10,000 dry short tons of live crushed ore available over the three reclaim pan feeders for each of the four primary grinding mill circuits. Dozers must be utilized to re- claim and push the other crushed ore. Primary grinding mill throughput is

Jan 1, 1986

By Shahzad Moosa, John M. Pitt

Statistical variability in rock strength can be evaluated by rapid, inexpensive ultrasonic pulse velocity measurements, an important consideration since rational probabilistic design in rock is often hampered by the cost of obtaining sufficient strength data. Experimental ultrasonic pulse velocity measurements on a set of 96 limestone specimens showed two distinct statistical populations. Both populations followed Weibull distributions, with flexural strength distributions paralleling pulse velocity distributions. Thus, experimental results suggest that strength variability may be predicted from a few rationally selected strength measurements and several ultrasonic tests. The correspondence between strength and velocity may then be used to develop an experimental transformation function, allowing the development of a statistical distribution function for strength based on the known statistics of velocity. Comparison of experimental groups with full sets of corresponding strength1 velocity data showed the technique offers a fairly accurate description of the statistics of strength.

Jan 1, 1986

By Luis Angel De Montreuil

Ante el problema del tratamiento de minerales complejos, la demanda de eficiencia metalúrgica y bajos costos de operación, el ingeniero busca el apoyo de la mineragrafía como estudio microscópico de los minerales económicos. En ese sentido, el presente texto señala la importancia de la minegrafía -en tanto ayuda a la flotación de los sulfuros valiosos de los yacimientos peruanos. Asimismo determina las propiedades de los minerales con el fin de identificarlos.

Jan 1, 1986

By F. Q. Barnes

"Uranium, thorium and yttrium have been recovered, since the 1950s, from pyritic quartz-pebble conglomerates occurring in the basal sediments of the Quirke syncline at Elliot Lake. Gold, an element of interest in similar type deposits occurring worldwide, is a very minor constituent of the Elliot Lake conglomerates because the provenance area of the sediments had few gold-bearing rocks.Uranium, thorium and rare elements are found in resistate and diagenetic minerals occurring in the matrix of the conglomerates. The valuable elements are recovered from the acid soluble minerals during the milling process.Large uranium reserves occur in mines found on both limbs of the Quirke syncline. Major reserves are being developed on the South Limb of the syncline, where the Stanleigh Mine, among four past-producers, has been reactivated.IntroductionUranium and thorium commonly occur in anomalous amounts in coarse basal sediments. Radioactivity in basal conglomeratic sediments is generally attributable to resistate minerals, that rarely occur in concentrations high enough to be of economic significance. One type of basal conglomerate found worldwide, in Precambrian cratonic basins, has uranium or uranium and gold concentrations large enough to be of economic interest. Principal among the occurrences are the pyritic quartz-pebble conglomerates of the Huronian in Canada, of the Witwatersrand in South Africa and at Jacobina in Brazil.The uranium and gold mineralization of these conglomerates was derived from provenance areas where both elements occurred and were later concentrated through source degradation and deposition in placers in a reducing environment. Only the Huronian conglomerates, generally much richer in uranium but with negligible gold, have been exploited solely for their uranium content.The uraniferous conglomerates of the Huronian at Elliot Lake, 500 km north of Toronto, continue to represent a major world source and supply of uranium concentrate."

Jan 1, 1986

By J. S. Hall

The productivity and fuel efficiency of iron-ore blast furnace operations has greatly increased in recent times. These improvements, particularly to the Japanese steel industry, have primarily arisen from process engineering studies of the blast furnace and associated operations such as sintering. The development of fluxed sinter based on iron-ore fines reacted to produce highly reducible, low slag sinters has contributed further to a reduction in fuel requirements. The Pilbara province of Western Australia is a significant source of these iron-ore fines supplied to the international market. Increasingly, this market is being offered high quality ores from other foreign sources. To technically assist companies in improving the processing efficiency of ores, and to improve the technical marketing of ores by modelling the processing characteristics of Australian/international ore blends, the Commonwealth Scientific and Industrial Research Organization (CSIRO) is actively assisting the industry by researching the general theme of 'iron ore from mine to metal in this paper we outline progress towards a numerical description of: a. ore deposit classification. b. Degradation during transport. c. Direct reduction of iron ore. d. Liquid bath ore reduction/smelting. e. Industrial sintering.

Jan 1, 1986

By S. G. Malghan

Flotation circuits of a range of complexity are in use for a large number of ores. Since each ore is different and end-product quality requirements are not necessarily the same, circuit configurations of varying complexity are designed. How- ever, certain basic types of circuit configurations can be identified based upon the flotation behavior of the ores. These basic types can be combined to develop the specific f lowsheet configurations for a given ore. This chapter begins with a brief discussion of basic flowsheet configurations. Examples of the flowsheet configurations for a number of specific ores bearing different minerals are then described.

Jan 1, 1986

By Holliday R, Floyd JM

A laboratory investigation was carried out to determine the distribution of gold between the products of lead-zinc concentrate smelting in the Imperial Smelting Furnace (ISF). Bullion, speiss and slag from the ISF at Cockle Creek were used as the starting materials to evaluate the effect of gold and copper content of products on the distribution of gold between phases under conditions simulating those in the ISF hearth. The ratio of gold in bullion to gold in speiss has a mean value of approximately 1.6 and is independent of the gold content of the bullion. The distribution coefficient of gold between bullion and speiss is dependent on the copper level in speiss and is lowered by increasing copper content in speiss. The ratio of gold in bullion to gold in slag is in the range 25 to 5700 and dependent on the gold content of the bullion. For low gold concentrations in bullion of the order of 1 g/t and a bullion to slag ratio of 1:3 the gold loss to slag is expected to be approx- imately 23%. In all tests the gold in slag remained low, in the range 0.05 to 0.5 ppm provided metal prills were not suspended in Slag.

Jan 1, 1986

By Rustu S. Kalyoncu

Nonoxide ceramics with improved high-temperature properties could substitute for high-temperature alloys and reduce toe Nation's dependence on imports of Cr, Co, Ni, and Mn. To meet this objective, the Bureau of Mines conducted research to synthesize u1trafine reactive boron nitride (BN) powders BN powders were prepared at temperatures ranging from -75? to 750? C. Low-temperature reactions (-75? to 200? C) between boron halides and N compounds led to formation of e1emento-organic compounds that were thermally decomposed to u1trafine (approximately 100-to 150-A particle size) reactive BN powders. BN powders were also prepared through the reaction of a 10w-me1tinginorganic B compound (boric acid, borax) with an organic N compound (carbimide and thiocarbimide) in N2 and/or ammonia (NH3) atmospheres at temperatures between 500? and 750? C.

Jan 1, 1986

By W. W. Simpson

During cyanidation of mercury-bearing gold-silver ores, significant amounts of mercury are extracted. The presence of mercury decreases. gold loading and increases mercury stripping time on activated carbon, complicates fire refining of the gold cathodes, and creates a potential health hazard. Addition of calcium sulfide (CaS) to the cyanide leach slurry precipitates the solubilized mercury but also some silver. The Bureau of Mines investigated silver loss during CaS precipitation of mercury. Addition of 0.1 lb CaS per short ton ore to a mercury-bearing gold-silver ore precipitated both mercury and silver. However, if copper was added with CaS, or if the ore contained copper, much of the sil-ver loss was prevented. Addition of 235 ppm Cu with 0.1 lb/st CaS, prior to carbon-in-pulp adsorption, resulted in 89-to 97-pct, 80-to 91-pct, and O-pct adsorption of the solubilized gold, silver, and mer-cury, respectively, on the activated carbon.

Jan 1, 1986

By Young C. Kim

Determination of the minimum sampling requirements of the run-of-mine (ROM) coal is very important for the purpose of meeting contract specifications. It is also important for the purpose of meeting emission regulations at a coal-burning power plant, such as the one located at Homer City, Pa. The classical statistical sampling theory can be applied to this problem, if ROM coal samples are known to be spatially (or serially) uncorrelated. On the other hand, the estimation variance concept from the Matherson's geostatistics must be used, if the samples are spatially correlated. Conditional simulation technique combined with simulation of the existing mining method is used to determine under which circumstances ROM coal samples do not preserve the spatial correlation. Only after establishing the degree of correlation that exists among ROM samples, an optimal sampling scheme can be devised using either the classical statistics Or the geostatistics. The minimum required sample volume can then be calculated using the well-known Gy's formula. This paper describes the results of the above investigation using the Helen coal mine data of the Homer City Owners. Empirical guidelines for determining the degree of correlation are also provided for coal mine operators.

Jan 1, 1986

Geological. engineering is a field of engineering practice concerned with design and construction of excavations and structures in soil and rock masses. The role of geological engineering in mining practice is defined in this paper, and the scope of the various disciplines in engineering science and geoscience which support geo-engineering research is discussed. The current national research capacity in geo-engineering is considered, and current and future needs for geo-engineering research for mining practice are proposed. Education programmes to sustain the proposed level of research and its industrial implementation are Suggested.

Jan 1, 1986

By R. Raymond

The occurrence and distribution of organic sulfur in coals may be investigated using electron probe microanalysis, scanning electron microscopy, and optical petrography. A general relationship exists between macerals and organic sulfur contents in individual coals: sporinite, resinite = micrinite, vitrinite > pseudovitrinite = semifusinite = macrinite > fusinite. With increasing organic sulfur content of a coal, the total range in organic sulfur content between macerals containing high and low organic sulfur contents likewise increases. Furthermore, the organic sulfur content of the vitrinite in most coals equals the organic sulfur content of the coal. For any individual coal, organic sulfur contents of macerals correlate inversely with reflectance-in-oil measurements, but the amount the organic sulfur contents vary between macerals cannot be calculated based solely on the coal's rank. Formation of pyrite following peatification has no effect on organic sulfur contents of surrounding macerals.

Jan 1, 1986

By K. R. Wood, G. W. McDonald

"The tailings disposal system at Les Mines Selbaie includes dewatering of tailings in a high-capacity thickener, followed by point discharge of the thickened solids to form a stable conical pile. Tailings water drains to ponds formed behind engineered dams, prior to either recycling f or process use or discharge to the environment. Design and economic considerations of the system are discussed. Construction, start-up and operating experiences are also presented.Introduction Les Mines Selbaie is located in the Abitibi region of northwestern Quebec, approximately 700 km north of Toronto and 150km south of James Bay. More locally, the Detour gold mine is 60 km to the west while the Noranda smelter is 220 km to the south.The deposit was discovered as a result of a Questor INPUT Mark VI geophysical survey in 1973, followed by diamond drill programs from 1974 to 1976. Three mineralized zones were delineated and underground exploration was carried out on all three. A production decision for the 'B-zone' copper-gold-silver orebody was made in July 1979. The underground operation started in July 1981, with full production of 1500 t/d being achieved in May 1982.During the planning phase, every effort was made to ensure that the operation would be environmentally sound . The design included the provisions of the then newly proposed provincial environmental guidelines. The tailings disposal system formed the most significant part of the environmental program due to the large volumes of solids and water effluent. In addition, the design allowed for future expansion of the system to accommodate mining of the other zones, thus minimizing future costs and disruptions."

Jan 1, 1986

By A. V. Castelli

Since the record year of 1981 through 1985 the tonnage of weighting materials (barite and other heavy minerals) used in drilling fluids has decreased an estimated 49%. As in the past, barite still makes up over 90% of the minerals used for weighting materials in drilling fluid. Domestic production of barite has decreased 69% since 1981 and imported barite has made up over 50% of the total barite consumed since 1982. See Figure 1 for usage of barite. The number of operating grinding plants has decreased from 69 in 1982 to 39 at the end of 1985. With the decrease in demand of weighting materials for drilling fluids and an over capacity of grinding existing, prices for weighting materials have decreased dramatically. Although the American Petroleum Institute has not changed any of the specifications for barite, some users have initiated their own new specifications and have proposed to have them included in the API specifications. The exploration for and development of oil and gas dictates the level of weighting material used in the drilling fluids industry. Most forecasters do not foresee (or predict) increases in the level of drilling until the 90's. The primary or unground barite produced in the U.S. mines has a difficult time competing with imported barite due to the location of the mines. These mines are located in North Central Nevada, with small tonnages being produced in California, Missouri, Illinois, Montana and Washington. The major reason, is the difference in transportation costs from the mines versus ocean freight rates from the foreign ports to the major area of use, the U.S. Gulf. Since 1981, the production of primary barite has decreased from 2,849,000/ST (2,584,596/MT) in 1981 to an estimated 890,000/ ST (807,403/MT) in 1985(1). If it were not for the use of unit trains by some producers the production of primary barite in the U.S. would have probably declined another 20% in 1985. During the same period, of the total amount of barite consumed in the U.S., imported barite ore increased from 417, in 1981 to 65% in 1985. The major exporting countries to the U.S. during this period were China 46.27, Morocco 15.27., Chile 10%, Peru 8.4%, India 7.9%, Mexico 5.4%, Thailand 3.9% and Ireland 2.3%.

Jan 1, 1986

By Armstrong ME

The gas bubble energy generated by an explosive plays a major part. in the fragmentation, muckpile movement and damage produced. Previously, the interaction between gas pressure and the rock has been interpreted from a theoretical basis or a qualitative study of breakage mechanisms. A method to measure the fluctuations in gas pressure in rock adjacent to the blast has been developed. This peak pressure will vary with structure, as well as with distance and explosive type. The technique is simple to apply and can be used to observe the flow rate of gas at. varying distances. The apparent velocity of penetration is an indication of whether gas has travelled through pre-existing or blast induced cracks. The technique provides a ?n:eans of determining the suitability of an explosive for a given rock type, depending on the amount of displacement desired. The technique has application in optimir.irig throw blasting and predicting and controlling damage, particularly in highly structured rock masses.

Jan 1, 1986

The Queensland Department of Mines believes it is in the best interests of the gold mining industry to reduce and control the environmental impacts from gold mining since that is the community expectation.The Department of Mines has set as a special condition of many recently granted Mining Leases the requirement to submit a "Description of Operations" for the approval of the Minister, prior to commencing initial mining operations. In order to facilitate compliance by lessees with this condition an explanation is given of the reasons for this condition and how it is intended to achieve the objective of environmental protection.Environmental impact is operations dependent. Impact on a lease will vary quite significantly with the scale and methods employed. Before a lease can be granted and mined it is therefore necessary to have this information. The parameters of operations most critical both in terms of environment impact and economic viability are worked out and agreed with the lessee before the lease is granted. An approved description of operations which is required now, prior to the start of mining, provides the details of that agreement for the security and benefit of the lessee and the inspectors. It also provides the details of operations and environmental controls which were not required prior to the grant of the lease but are nevertheless required and necessary for compliance with the environmental standards.

Jan 1, 1986

By J. A. Herbst, L. B. Hales, R. Zaragoza

INTRODUCTION The Control Problem The need for automatic control in flotation plants stems from frequent and randomly occurring disturbances to the feed slurry. Typical disturbances occur in the solids feedrate, the slurry percent sol ids, and the mineralogy and flotability of the gangue and valuable minerals. In plants where semi -autogenous grinding mills (SAG) are used, feedrate changes are very large and changes in feed percent solids of 1m or more are common. Mineralogy changes between valuable minerals are common, as are changes in the host gangue rock. As these changes occur, the operator can attempt to compensate for them by making adjustments to the flotation cell levels, the dosage rates of the collectors and frothers, the pH, and in some cases the aeration rate of the cells. This problem is sometimes complicated by the fact that different sections of the flotation plant will be processing different ore types at the same time. Potential Savings with Control Flotation control brings about savings or plant improvements in two areas; the first is in improved metallurgy and the second is in reagent savings. Improved metallurgy includes increases in the average plant recovery and achieves target concentrate grade level s more consistently. Average recovery increases between 1.0 and 5.0 percentage points have been widely reported (Paakkinen, 1979; Sutherland, 1984). Reagent savings of up to 40 percent have also been reported (Hales, 1985). VARIABLES OF IMPORTANCE Control led, Manipulated, and Disturbance Variables The initial step in the analysis of the flotation control problem is identification of important variables which can affect the efficiency of separation. The efficiency of separation is represented by a group of controlled variables which can quantify the performance of a flotation circuit. This group includes variables such as grade, recovery, tonnage through- put, and circulating loads. The efficiency of separation of a flotation circuit may generally be defined by a grade recovery map, where each point on this map re- presents a set of operating conditions (see Figure 1). However, the combination of operating conditions must be set to operate close to the economic optimum. The group of operating variables which are changed in order to achieve desired circuit performance are called manipulated variables and can be classified into two

Jan 1, 1986