Search Documents

By C. J. Im

As market conditions become more competitive, U.S. coal producers are faced with the increasing need to find methods of lowering production costs in their operations. One area worthy of investigation is the additional recovery of fine coal that is normally discarded in the preparation plant waste stream. United Coal Company is currently assessing the capability of the Deister Flotaire, a new application of a column flotation cell, to recover additional, saleable coal from preparation plant waste. This paper presents the technical data obtained to date. Work with a 0.76 m (30 inch) diameter cell installed in a plant shows considerable coal recovery is possible from a nominal 0.595 run (28 mesh) X 0 refuse stream.

Jan 1, 1986

By Mark A. Anderson

INTRODUCTION The accomplishment of a well engineered design, and the realization of efficient plant operation cannot be achieved without weaving a web of safety consciousness from the beginning of the project. When the plant becomes operational, and throughout its life, responsibility safety will rest with the client or operator. Recognition of this understanding does not reduce the importance of the engineering and construction contractor's role, but merely puts the responsibility where it belongs. A project which has had little or no operator input during the early stages of design is almost certain to have serious work place safety, health, and environmental problems in spite of the fact that all MSHA and OSHA design requirements were met and the engineering was performed using accepted practices. DEFINITIONS The author has a personal preference in safety definitions that begins and ends with simplicity. If the safety criteria, program, and rules are confusing or complex, the results will soon become obvious. Confusing and complex are the key elements in the avoidance of responsibility and if punitive is added to the list, a brew exists which breeds accidents, illness, and poor performance. A safely designed and operated plant is one that a worker can journey to each day; leaving that person and his or her family with the above average expectation that the person will return healthy, emotionally intact, and hopefully a little wealthier. If the objective or results of a planned or existing safety program don't fit the definition. then the reader is probably contemplating a very sophisticated

Jan 1, 1986

By Peter A. Hacquebard

"Two continuous coal zones occurring in a 2500f t (762 m) thick section of the Upper Carboniferous Pictou Group (Westphalian C and D) have been encountered in five offshore wells drilled f or oil and gas in the Gulf of St. Lawrence. They correlate, by means of fossil spores, with thick coals of the Mabou and Inverness coalfields situated at the eastern margin of the Basin. Therefore, the presence of a large submarine coalfield of at least 18000 sq mi. (46 620 km'] is indicated. This compares with an estimated size of 14 000 sq mi. (36260 km' ) for the Sydney Coal Basin.Accessibility is provided only by the small onshore parts of the Mabou and Inverness fields, because farther offshore the coals lie too deep to be mined (below 4 OOO f t ([ 219 m)).Two near-shore coal exploration wells indicate that at Mabou Mines the younger Inverness coals occur at a mineable depth to at least 5 km from land. A structure contour map of this area shows a reserve of 125 million tons in two Inverness equivalent seams that are 8.5 ft (2.6 m) and 4.5 ft (f.4 m) thick. The Mabou coals, however, reach too great a depth close to shore to possess mineable resources.A structure contour map of the Inverness submarine area, based on mine data and one off shore seismic profile, indicates inferred mineable resources of 160 million tons, in two seams that are 7ft (2.1 m) and 4.5 ft (f.4 m) thick . A detailed deep seismic survey will be necessary to substantiate the structure and resource estimates"",Maceral and coal quality percentage diagrams of five column samples of these seams (the 7 Foot and 13 Foot Seams of Inverness Equivalents) show a bright banded coal, high in reactive macerals, which will produce a weak coke unsuitable f or metallurgical purposes. A thermal coal with a rank of H. V. ""B"" Bituminous (0.64% Ro) is present, averaging 12000 btu llb (6 660 kcai/kg), 10% ash and 6% sulphur, of which 60 to 80% is derived from pyrite.Microlithotype profiles of the major Mabou and Inverness coals show characteristic successions that can be used f or seam identification and proved valuable f or structural interpretations.The time of faulting in the major fracture zone on the eastern margin of the Gulf of St. Lawrence Basin has been deduced from coal rank variations. It occurred in pos tPermian, probably Early Triassic time."

Jan 1, 1986

By J. T. Tanner

The research activities of the Minerals Research Laboratory, which is a part of North Carolina State University, is normally confined to solving beneficiation problems, and developing flotation processes for the mining industry. In recent years the laboratory has veered from its main purpose somewhat and has placed some emphasis on the manufacture of products from mineral concentrates. This has been the result of requests for help from industry. One such request came to the MRL from a talc producer in North Carolina who was having a difficult time competing with foreign imports of steel marking crayons. He felt that if a process could be developed whereby a satisfactory crayon could be produced from powdered talc at a low cost that he could compete.

Jan 1, 1986

The Australian gold industry has in recent years experienced a tremendous growth period, though not to levels prevailing at the turn of the century. There are, however, a number of dynamic factors at play which collectively indicate that it would be unwise to assume that this growth will be maintained; indeed the future discovery of viable new deposits may be insufficient to prevent an industry decline in Australia.The higher gold prices of the 1980's together with technological advances, made previously worked mining centres areas of excellent prospectivity. These resources, signposted for us by the oldtimers, are being rapidly depleted. Whilst there can be no doubt that these resources can be replaced the real question is whether it is economic to explore for new deposits when it is likely that:The cost of future exploration will increase as exploration must focus on grassroot areas with few signposts. Almost by definition this primary exploration effort will be subject to a lower success ratio.The cost of future exploration will increase as new deposits will be located in more remote areas and at depth.

Jan 1, 1986

By Canning RL, Pritchard J

The surface treatment works in the Mount Isa Mines Limited copper stream consist of a concentrator and smelter with annual capacities of 5.6 million tonnes of ore and production of 155 000 tonnes of anode copper respectively. Both plants have been sites for process optimisation in recent years, the emphasis being to achieve productivity gains in each particular plant. The continued low real world prices for copper resulted in an in-depth review of the entire copper process stream. This indicated the need for developments within both the concentrator and smelter, and changes to operating strategy to ensure that the entire treatment stream could be optimised. The paper reviews these changes.

Jan 1, 1986

By G. H. Matthes

Many mines, in particular coal mines, use inclines or slopes as an access to seam or seamlike deposits which outcrop at or close to the surface. In general, from the surface or from a certain depth, inclines or slopes follow the dip of the deposit with length up to 30,000 feet and by that going under an overburden cover of several thousand feet. The common outbye transport system for mine products is the conveyor. Material and men to be transported down into the mine are handled by rope driven systems when the angle of inclination exceeds the employment of locomotive traction. The transport volume can be sizeable and reach 200 to 300 tons of material and 500 men to be handled daily in a medium size coal mine with a production of 10,000 tons ROM.

Jan 1, 1986

By H. E. Hirsch

Propelled by the invention of the transistor at Bell Laboratories, germanium's unique properties have advanced our electronic world by many years. Germanium has found major uses in infrared optics, fiber optics and a revised vigor as a catalyst for PET plastic production. Other advanced applications are in various stages of development. The solid state electronics industry has been the driving force behind the accelerating demand for gallium since the late sixties. Past developments of substrates for light emitting diodes, lasers and magnetic bubble memories are paling in view of the current excitement over the use of semi-insulating gallium arsenide for high performance integrated circuits. This application requires gallium metal and gallium compounds of extraordinary purity.

Jan 1, 1986

By H. P. Schlanger, L. Paterson, B. H. G. Brady, B. E. Hobbs

A novel principle for a waste repository, based on a backfilled thermosyphon as the functional unit, is proposed. Such a unit reduces temperatures and temperature gradients in the vicinity of a waste package and in the repository near field, reducing leach rates from packages and thermomechanical disturbance of the rock mass. Preliminary analyses confirm the mode of performance of the system, and reveal some interesting features of material transport and sealing in backfill and rock fissures. The thermosyphon combines attractively with the prospect of developing a near-field geochemical trap with chemical specificity for radionuclides. It is proposed that a thermosyphon repository may provide superior performance of engineered and natural barriers compared with conventional designs. The achievement of the ability to predict accurately the performance of the thermosyphon, relative to other isolation schemes, will represent a benchmark in the understanding of the absolute performance of any repository.

Jan 1, 1986

By Michael G. Pojar

This Bureau of Mines report estimates the population of the principal types of machinery in use by the coal mining industry during 1982 in surface and underground mines. Estimates were arrived at using 1976 coal equipment population estimates as baseline data with modifications made for new mine development, expansion, and closure occurring during 1976-82. Estimates were broken down into 3 regions which included all 26 coal-producing States. Modifications made to the baseline data were computed using (1) actual equipment information when available, plus (2) equipment information hypothesized from representative generic mine models, which were predicated on mine size and mine method. Roughly half of the equipment fleet at new or expanding coal operations was known; the remainder was hypothesized. The mine models used to generate equipment information are included in this report, along with the hypothesized equipment use data. The equations and various factors used to determine the equipment adjustments for mine closings, new mine openings, and small coal mine operations are also identified.

Jan 1, 1986

By Robert D. Hansen, Basil S. Fee, Richard R. Klimpel

Despite the importance of froth flotation to the mineral industries as a means of separating various minerals, the commercial flotation reagents used have varied little in the last twenty years. Numerous articles and books are available describing existing flotation chemistry and its application, e.g., Fuerstenau (1962), Fuerstenau (1976), Aplan (1980), Somasundaran (1980), King (1982), Leja (1982), Ackerman, et. al. (1984), Crozier (1984), Hansen and Klimpel (1985). There are many reasons for this lack of significant new reagent development including the general utility and relative cheapness of collectors, such as xanthates, and frothers, such as methyl isobutyl carbinol and the glycol ethers. Another important reason is the inherent complexity of the flotation process itself coupled with highly variable and difficult to standardize feed materials which make reliable reagent comparisons difficult and seriously limit the use of theoretically based studies to "predict" new or optimal reagents. In addition, the higher cost of "specialty flotation reagents demands that their performance attributes be significantly greater than existing general all- purpose commercial reagents – something often difficult to prove in practice. Faced with this situation, a detailed applications research pro- gram [Klimpel (1980 ab, 1982, 1984 ab), Klimpel, et. al. (1982)] was organized from 1979-1985 on mineral flotation with the following goals: 1) the development of appropriate batch laboratory flotation testing techniques sensitive enough and statistically reliable enough to identify small differences in performance between different flotation tests (i.e., between various reagents, even those with relatively minor chemical structural changes); 2) the identification of mathematical models with appropriate numbers and types of parameters that have maximum statistical power to statistically distinguish between various time-recovery profiles; 3) the generation of laboratory and corresponding plant scale data in sufficient quantity and consistency so that the highly interactive nature of the "flotation system9' of chemistry/ equipment/operating conditions could be quantified; and 4) the invention and development of really new and unique reagents for giving improved flotation performance. The goal #1 was achieved [Klimpel (1980b. 1984b), Meyer and Klimpel (1984)l by basically using a simple automated paddle device for consistent

Jan 1, 1986

By R. D. Smith

The Bureau of Mines (BOM) evaluated the technology, capital investment, and annual operating costs of emission control for further reductions of lead in ambient air at the East Helena, Montana, smelter, and the Glover, Herculaneum, and Buick smelter-refineries in Missouri. This study seeks to analyze the technology available to the domestic primary lead industry for attempting to further reduce lead emissions below 1985 levels. Through enclosure of concentrate unloading and handling areas and all lead-processing buildings, followed by venting these enclosures to the atmosphere through baghouses and the application of appropriate local controls, emissions can theoretically be reduced by a total of 2,424 pounds of lead per day from 1985 levels at the three Missouri operations. Using conventional technology, aggregated additional capital costs of $250,014,000 and annual operating costs of $18,507,800 are estimated for the four operations, resulting in a total cost of $0.063 per pound of refined lead. Continuous drossing techniques would assist in meeting OSHA standards in process areas. Continuous drossing would change capital and operating costs to $258,344,800 and $16,104,700, respectively, for a total cost of $0.062 per pound of refined lead. First quarter, 1986 open market price for refined lead was $0.184 per pound.

Jan 1, 1986

Economically significant gold-silver mineralization occurs in Miocene andesitic flows and tuffs at Golden Cross, eight kilometres northwest of Waihi, New Zealand. The highest grade mineralization occurs in a steeply dipping elongate zone of strong quartz veining and brecciation underlying, but contiguous with, a gently dipping tabular quartz vein stockwork containing potentially open-pittable lower grade gold-silver mineralisation. The stockwork zone is enveloped by argillic alteration and overlain by unaltered Pliocene andesites and recent tephra. Evaluation of the prospect involved underground and surface geologic mapping, rock and soil geochemistry, IP-resistivity, magnetic and gravity surveys as well as 1844 metres of reverse circulation drilling and over 30 000 metres of core drilling. The paper outlines the exploration history of the area and describes the results of the various exploration techniques used at Golden Cross.

Jan 1, 1986

Technological advances evolve in different ways; many are the result of years of application of scientific method. i.e. Observation Deduction Hypothesis Proof In the mining industry, better explosives, drill bits or reagents are likely to evolve in this way. The scientific method is suited to the application of conventional management structures. Other advances are simply the result of a "brainstorm", or building a better mousetrap. Such inspiration probably resulted in "Split Set" rock bolts, or the first use of a vacuum cleaner principle for shaft mucking. Individual consultants can apply lateral thinking to generate such inspiration. In gathering material for the presentation of this paper, I sent a.letter to all members of the Mineral Industry Consultants Association asking them to nominate problems in the industry requiring investigation. The answers have been divided into two classifications - contract research underway and identified problems requiring solutions.

Jan 1, 1986

By R. C. Keaney

The metals industry is in complete chaos with mines being shut down, profits becoming non-existent, and continual losses to imports from other countries. Yet the raw material supplier to the glass industry has many opportunities to grow and to produce profits. Fortunately, the cost of most glass raw materials are low enough that competition from imports is not anywhere as critical as it is in the metal industries, such as copper, aluminum, lead, and others. But the glass raw material supplier must develop new products, both chemically and physically, to effectively compete in the future. The purpose of this paper is to point out generally where these opportunities exist and to suggest how they may be further developed. As the glass industry looks for energy saving materials, they look once again towards finer materials. A glass furnace is now approximately 40% efficient. Glass engineers are constantly striving for energy savings and it is well known that finer materials melt easier so that the manufacturer can operate his furnace either at lower temperatures for the same production or he can produce more material at the same temperature. The old 20 mesh sand specification is no longer sacred and as the mesh size for sand changes so do the specifications for all other raw materials used in the melting process. Highly instrumented glass furnaces can now measure quite accurately the energy needs to produce glass and can also measure the energy loss in each furnace. Glass technologists desire today a sand with a top size of 40 mesh while some would like to have the top at 60 mesh. This becomes more difficult to accomplish as a raw material supplier without .grinding. As you well know, grinding develops fines. Yet the same technologists will tell us that we can have nothing passing a 140 mesh screen. Therefore, we must develop processes which allows us to produce a finer screen size without increasing the amount of fines passing through the 140 mesh screen. To counteract this, different and changing industries are now demanding much finer products so possibly there will be markets for the fines which are currently separated out of the products. Methods that are practical and low cost must be found to develop different products with different screen specifications. What works for sand can be carried over to the other raw materials used in melting. Among the answers to finer products, of course, are pellets. Aglomeration or pelletizing has been looked at in the past and will be looked at in the future. Considerable work has been done in the glass container industry on this and must be carried out more extensively. By using aglomerated material or pellets, the glass producer will gain the benefits of melting fine materials without suffering from handling or dust problems. Pelletizing, particularly where using basic glass melting materials such as burned lime or sodium silicate, will not only produce a good pellets but will add desirable minerals to the glass batch.

Jan 1, 1986

By John T. Berry, Robert D. Pehlke, Michael J. Beffel

"Pattern making and metal casting organizations are currently adopting CAD/CAM systems and implementing this technology in design and production. Al though significant progress has been reported, these systems generally are based on two or two and one half dimensional analyses. Very few are based on solid geometric modelers.The present paper emphasizes the need for solid geometric modeling of the casting and rigging system and linkage with a solidification simulator. The nature of some of the technological challenges which have slowed this development are discussed, including accurate description of complex surfaces and their intersections and the bridging of computer encoded information with NC technologies and with FEM-based simulators for stress and thermal analyses. A recently prepared modular-structured FEM simulation code implemented on a micro computer is described.Construction of a solid geometric model of the casting and rigging and validation of the combination for optimum characteristics of soundness, quality and yield by solidification simulation are I inked as key elements in the foundry of the future. Data base support for this CAD/CAM system is rapidly being developed throughout the world.INTRODUCTIONThe simulation of shaped casting solidification using the digital computer, goes back to at least the early nineteen-sixties when Forsund (1) in Denmark applied the technique to the problems of casting surface quality.Prior to that time, the work of Paschkis and co-workers using the analog computer ranges back to the nineteen-forties, when work sponsored by the AFS Heat Transfer Committee at Columbia University revealed many hitherto unknown or only partly anticipated aspects of casting solidification (2).Three reviews of the various historical aspects of simulation should be referenced. Firstly, the AFS monograph by one of the present writers (RDP) and his colleagues - describing background and later work, again sponsored by the AFS Heat Transfer Committee at the University of Michigan (3). Secondly, a review prepared by Durham and Berry (4) which discusses broad aspects of casting solidification simulation. Thirdly, a review by Erickson (5) which contains an excellent bibliography to 1980. In addition to these papers, the publications lists of the CADCAST project* and the proceedings of the two Engineering Foundation Conferences of Casting and Welding Modeling, published by ASME, are also most notable (6) •"

Jan 1, 1986

By C. L. McKenzie, R. A. Heig

The design and operation of metallurgical laboratories is discussed. Laboratory size, general laboratory equipment and metallurgical staffing are discussed from a standpoint of desired laboratory results.

Jan 1, 1986

By Koivunen P

Both development and production drilling are amenable to productivity improvement through partial or full automation of drill jumbos and rigs. Various developments in this regard are described.

Jan 1, 1986

By R. Hamar, G. Lamanthe

"To realize complex shaped pieces, like turbine blades, superalloys are cast with the lost-wax process. The end properties of these parts depend upon their microstructure as well as upon the occurence of casting defects such as micropores and hot tears. Such features are governed by the local solidification conditions which may be describe by the calculation of thermal transfers between alloy and mould. It needs the evaluation of numerous parameters which are fitted from experimental measurements in real castings. In further simulations, any parameter may be changed, in order to determine its influence. Such a single modification is quite impossible to realize in real castings, which shows that numerical modeling is a very good way to study casting processes.This modeling technique of casting is applied here to the real study of a typical low pressure turbine blade of a civil engine.IntroductionAircraft engine manufacturers use superalloys to produce turbine blades. They have to obtain a given microstructure and to avoid solidification defects to give good mechanical properties to theirs castings. For example, microporosity is induced by a large shrinkage that cannot be completely fed with the remaining liquid alloy .The optimization of casting processes needs a good Knowledge of the solidification process, that must be controlled at every place in the casting, and at every time of its freezing. Material and heat transfers that occur during the solidification, can be estimated from rather complex calculations. To model these physical phenomena, the evaluation of many parameters must be made. In this aim, some casting experiments are fitted with numerous thermal captors. The identification of experimental and computed thermograms let us estimate these parameters.A long-range scientific cooperation between SNECMA and INPG has enabled the realization of such studies on this topic. From all of them, this paper describes an experimental and computed investigation which has been led on a typical low pressure turbine blade of a civil engine."

Jan 1, 1986

By Michael M. Carroll, Zhu-ping Duan, Han-ping Chin

INTRODUCTION The inelastic stress-strain behavior of rocks has urged engineers to seek for the possible application of plasticity to engineering pro¬jects such as tunnels, oil wells, dams, etc. for a long time. Early efforts in this direction have tentatively used the classical theories to solve some axisymmetric problems, in which the rocks were treated as perfectly plastic and nonfrictional materials (Talobre, J. A., 1957). Meanwhile, one of the fundamental assumptions is that the volume strain of elastoplastic material is purely elastic. Drucker and Prager (1952) developed a perfectly plastic and frictional model with a generalized form of Mohr-Coulomb law, which serves as both failure criterion and yield criterion. Although the associated flow rule gives unacceptably large dilatancy, this model is a very important step to deal with the frictional behavior of geological materials. As a further step, Roscoe et al (1963) and Schofield and Wroth (1968) proposed a Cam-clay model, which accounts for the yielding before the material reaches a failure envelope and reflects the plastic volume strain as a strain hardening factor, and the open end of the Drucker-Prager envelope is capped by a family of yield surfaces, the envelope is made conforming with crit¬ical void ratio line. The proposed shapes of the cap have been based on experimental data and on convenience of mathematical descrip¬tions. Drucker, Gibson and Henkel (1957) introduced a spherical cap for soils, while in Cam-clay model the cap is semi-logarithmic yield function derived from the result of triaxial tests. DiMaggio and Sandler (1971) proposed an elliptical model for sand, in which the hardening function depends exponentially on plastic strain. Sandler et al (1976) used a plane cap model to express the behavior of a wide range of geological materials of which the nonlinear hysteretic nature is significant. Mizuno and Chen (1982) illustrated the physical mean¬ing of cap models and their adaption to finite element calculation. In recent years, Carroll et al (1972, 1980) have studied the com¬paction of porous materials under hydrostatic pressure and discussed the mechanism of the nonlinear response thoroughly. Analytical and numerical analysis of the hollow sphere model by Curran and Carroll (1979) predicted an initial yielding surface, dependent on the initial porosity, and showed a strong coupling between hydrostatic and deviatoric effects. All these main features from the abovementioned theoretical research are visualized by the experimental data on Boise sandstone (1984). The combination of such previous work would be logically the construction of a plasticity model for porous rocks which, following the tradition of assigning the name of birthplace to a special model, is called Cal-Rock model (Carrol, M. M., 1984). The results of triaxial tests along different loading paths reveal the compaction characteristics for deviatoric and hydrostatic stress separately. the fitting of the nonlinear stress-strain curves leads to a construction of yield surfaces. Moreover, an uniaxial strain test gives the strength envelope which is the critical state line. The whole model is composed in the frame of elasticity theory. The concept and representation of plasticity used here are in the spirit of Naghdi¬Casey theory (Casey and Naghdi, 1984 and 1984, Naghdi and Trapp, 1975). In order to find the way of using such a plasticity model in engineering problems, the stress field in a thick-walled cylinder of porous material is calculated. This is an axisymmetrical problem with plane strain, which is an idealization of oil well in an infinite medium. Because the constitutive relation is highly nonlinear, a numerical method has been utilized to obtain the solution. CONSTRUCTION OF CAL-ROCK MODEL (1). Elastic-plastic constitutive equations The basic assumption is that the yield surface in stress space depends on one parameter, namely the plastic volume strain, as the data on Boise sandstone suggested. Starting from this point, the theory formulated in stress space and in strain space by Naghdi and his co-workers (1975, 1981) can be simplified. The simplified yield function is

Jan 1, 1986