Search Documents

By Robert C. Dyni

The Bureau of Mines in cooperation with the Solution Mining Research Institute conducted surface and subsurface investigations over five solution-mined salt cavities in the Hutchinson, KS, area. The purpose of these investigations was to determine the mechanisms that lead to the formation of sinkholes above collapsed solution cavities. Of the five salt-solution cavities investigated, four had collapsed and produced sinkholes prior to the time of the investigations; the fifth cavity was considered stable. Exploratory drilling and coring operations were conducted at all five sites; surface stability monitoring was conducted at three of them. The results of these studies indicate that excessive dissolution at the salt-shale contact of each collapsed cavity produced large, unsupported roof spans that ultimately exceeded the structural integrity of the overburden. The stable cavity was not exposed to excessive dissolution at the salt-shale contact; this limited the roof span and ensured a stable cavity. The data also show that surface settlement in the vicinity of the two surface-monitored sinkholes continued for approximately 7 years after the sinkholes formed, indicating that the rubble piles of the collapsed cavities were undergoing gradual consolidation.

Jan 1, 1986

By P. K. Chatterjee

Before coal can be extracted from surface or underground mines, approval must be obtained from state and federal authorities. Permitting is the application process through which such approval is sought. The application includes en environmental impact statement Which focuses on Such topics as subsidence, toxicity of acid mine drainage, pollution levels of rivers and streams, post mining reclamation, and the effect on the hydrological balance of the area. The permitting procedure is extremely time and labor intensive, and requires extensive interdisciplinary knowledge. This paper examines a LISP based permitting procedure which will help to reduce the time taken to prepare and review a permit application.

Jan 1, 1986

By P. O. Rag, Daniel E. Walsh

"Gravity concentrators are evaluated either in closed or open circuit. The process developed by MIRL employs the use of neutron activated gold (/98Au) and radiation detection circuits which monitor the concentrator's product pulp streams. Concentrator recovery is determined from the ratio of the number of gold particles detected as passing into the concentrate to the total number of gold particles detected over all monitored pulp streams. This system eliminates the experimental errors introduced by sampling, sample reduction, and assaying and allows recovery to be evaluated for gold particles of specific sizes, shapes, and flatness. In addition to allowing for a more accurate and detailed recovery analysis, this process significantly reduces the time and cost required for unit evaluation when compared to other gold recovery analysis procedures. This system enjoys its greatest utility where a large number of tests are to be run in order to evaluate a concentrator over a variety of operational settings, i.e. factorial designs, and allows accurate testing of concentrators operated in closed circuit systems.IntroductionThe surge in gold prices of the late 1970s and early 1980s was followed closely by a renewed interest in gravity concentration processes, especially in concentrators claiming efficient recovery of fine placer gold. Cones, spirals, spinning bowls, jigs and cyclones are all considered potential fine gold concentrators. Fine gold, in this context, is defined as not only that gold finer than 250 um (60 mesh""), but also coarser gold, whose low shape factor may decrease its recovery by conventional, large-scale sluicing operations.Adoption of fine gold concentrators by the Alaskan placer milling industry was retarded by the lack of reliable, accurate, and reproducible data on concentrator efficiency with respect to fine placer gold recovery. In most cases, concentrator performance was based on a limited number of tests run on placer material, about which only slight knowledge of gold size and shape characteristics existed. In order to be prepared for the resurgence of interest in fine gold concentrators, which will follow the next upturn in gold prices, a detailed study of the fine gold recovery characteristics of gravity concentrators needs to be conducted."

Jan 1, 1986

Minimize drilling time in roof bolting. Approach The Bureau of Mines conducted a survey of 34 roof bolting machines used in underground coal mines. Results of the survey indicated that drilling time, bit cost, and respirable dust concentrations and be reduced by using the appropriate bits for drilling, To evaluate bits currently used and to find optimum cutting parameters needed to minimize drilling time, the Bureau tested two bits commonly used in most underground mines on both wet and dry systems. These are the dusthog* and shank type. The dusthog has dust ports in the bit body to remove cuttings. With shank bits, holes in the drill steel do this. Cost of each type is roughly equal. Bolters with dry vacuum systems were tested in the laboratory first. The lab tests were verified by underground tests in several mines. Bolters with low-pressure wet drilling systems were also tested under-ground. Tests concentrated on the effect of rpm, water and airflow rates, heating, wear, bit design and bit type. Lab Results -Dry Drilling Holes were drilled during the laboratory tests using a production model bolter drilling 45-inch-deep holes into mixtures of lime stone and sandstone aggregate. All tests started with new shank and dusthog type bits at 225 and 450 rpm. Thrust was about 6,000 lbs in all tests. Each bit was tested at two airflows, 15 and 25 cfm, airflows which are typical on operating roof bolter bits. Eleven styles of bits were evaluated. On the average, dusthog bits drilled 25% faster than shank types and were always cooler after drilling. The effect of RPM was tested with 5 different bit types. When bit rpm was increased from 300 to 400, drilling rates doubled. With used, well-worn bits drilling time and final bit temperature were more than doubled.

Jan 1, 1986

By Doxford CI, Perry AJ

Mining Lease 908, situated on Gorge Creek near its confluence with the present Cape River system, has been subjected to intensive recent exploration for alluvial gold.The gold is hosted by a buried palaeochannel, the Gorge Creek Lead and by an overlying remnant meander of the Cape River. The principal, if not sole, sources of gold within the Gorge Creek Lead are the northwest trending Great Australian Reef and Green's Specimen Reef systems which are situated on adjacent high ground. Lower grade gold bearing eluvial ground separates the reefs from the Gorge Creek Lead. The sources for gold within the old Cape River system channel (Canton Lead) are thought to be situated some distance upstream, one source perhaps being the Lolworth Diggings located 30 kilometres to the northwest.Exploration of previously "heavily dug" ground on both leads consisted of detailed geological mapping followed by the collection and treatment of bulk samples from eight costeans. The wash samples varied in size from 120 to 396 cubic metres. Treatment was undertaken through a commercial sized conventional wet screen and jig plant.

Jan 1, 1986

By L. F. McHugh

Molybdenum conversion operations discussed in this paper encompass all major operations commercially used to upgrade molybdenite concentrates to various refined products. More emphasis is placed on discussion of key pyrometallurgical unit operations. These operations conducted at Metec include roasting, sublimation, and hydrogen reduction

Jan 1, 1986

By D. V. Bush

The economic application of real time computer control can be broken down into 2 broad areas of concern. The first would be in gaining the most efficient utilization of energy. The second would be in improved product quality. This paper will be primarly concerned with the first area of efficient energy utilization as that area has the greatest effect on costs and thus net profits. Most process control strategy attempt to achieve the greatest comminution with the least amount of energy thus maximizing efficiency. A more direct approach to energy control involves a total mine and mill energy management system. In most cases these systems have an ability to achieve a very short payback period with the greatest return on investment.

Jan 1, 1986

By Russell P

Polyurethane resin (PUR) is extensively used in almost all coal producing countries. On the local scene, PUR components suitable for underground application were selected and subsequently, trials were carried out at several coal mines. This paper describes the work at Pikes Gully Colliery (B.P.3Coal), where water flow rates of up to 4.5 m (1000 gallons) per minute, were reduced to 1-1.5 m /minute at the tirst stage of application. Subsequent trials were carried out at West Cliff Colliery (Kembla Coal and Coke). A variety of PUR chemical mixtures were tested in coal ribs and in the roof of intersections and roadways. The trial results are presented with all particular details. Using the PUR injection method, the roof, at the most difficult intersection, was stabilised and 'de-bonded' roof bolts were re-sealed. At Pikes Gully and West Cliff Collieries, 2 tonnes and 3 tonnes of PUR chemicals were injected, respectively. The technique, primarily based on German experience (Bergwerksverband), was used by Delta Control Systems Pty. Ltd. ACIRL was closely associated with the trials, which were monitored by installation of the measuring Stations.

Jan 1, 1986

By Richard A. Allwes

A procedure is presented for the design of an arch canopy for the application of rehabilitating a high-roof-fall area. This procedure is specifically developed for evaluating an unbackfllled arch canopy, which Is subjected to an impact load (roof fall). Dynamic line loading of the arch canopy at its crown is only considered and the procedure does not account for an unsymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation is dependent upon many variables, including in-nine conditions and the engineering properties of the structure. However, a general evaluation can be based upon a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. A single spring-mass system is used as an idealized model to represent the dynamic behavior of the arch canopy at its crown. An energy approach is taken to determine the maximum crown deflection of an arch rather than solving a differential equation of notion derived from dynamic equilibrium. The design procedure is based on the concept that when an arch canopy is subjected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure Is that It gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1986

By Richard A. Winters

In 1985 at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 9,400 acres of the 10,005-acre Duncan Creek Wilderness Study Area (ID-111-78) in order to evaluate the mineral resources. The study area is located in Owyhee County, 10, about 36 miles southwest from Bruneau, ID. No mining districts are in the study area, nor were any mines or claims recorded or found. The southern half of the area was covered by oil and gas lease applications, all of which were cancelled prior to June, 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Duncan Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By S. Inaba, K. Taguchi, T. Uenaka, I. Mizuguchi, K. Umeji, H. Isako

At Kobe Steel Ltd., various improvements in pellet quality have been carried out since beginning lime-fluxed pellet production. Especially, dolomite-fluxed pellets, developed in 1975, have superior high temperature properties. With this improvement, successful BF performance has been achieved. But, in order to achieve more successful BF performance, improvements of physical properties such as the shape factor, reposed angle, and the bulk density are desired. Now, crushed pellets have been developed for the improvement of those characters. The test operation with these new pellets in Kakogawa No. 2 BF was carried out with successful results. This report describes the development of crushed pellets and their use in BF.

Jan 1, 1986

By D. Collins, B. Pina, G. Snell

The conversion of moisture and ash free (maf) coal to pyridine solubles and gas was investigated in a microautoclave batch reactor. Two washed Kentucky coal samples (KY # 9 and KY #11) were studied in liquefaction solvents of various donor strength. The liquefaction solvent hydrogen donor strength was varied by changing the tetralin content of a mixed 1 -methylnaphthalene-tetralin mixture. Primary liquefaction conversions in excess of 90 wt% in 10 minutes of reaction time @ 700° K (427OC or 800°F) were achieved with liquefaction solvents of moderate donor strength, i.e. 40% tetralin. A modified irreversible first order rate expression (eq. 1) described the experimental data:

Jan 1, 1986

By L. P. Meade

Dimension stone and salt are two of the oldest industrial minerals utilized. Salt has been and still is a necessity to the well being of man. Dimension stone on the other hand has been utilized by man to glorify conquests - both in the battlefield and corporate arena. Both commodities are important, but dimension stone has an additional use in that the survival lessons learned by the domestic industry can be applied to other contemporary industrial minerals, Specialization in the market place and customer service have allowed domestic producers to survive: subsidized foreign competition, obsolete equipment, and lack of capital.

Jan 1, 1986

By P. R. Bridenbaugh

The products of the coming decade will possess such stringent design criteria that it is unlikely today's monolithic materials will be able to meet them. The discovery, characterization and cost- effective manufacture of a whole new generation of highly engineered materials therefore have become essential requirements for participation in the materials marketplace of the 1990s and beyond. Meeting these challenges will require advances on a broad variety of scientific and engineering fronts, including: strengthened fundamental understanding of materials behavior; composite and laminate programs offering the compatible and synergistic combination of metals, ceramics and polymers; advanced engineering and structural design techniques; processing technologies capable of producing advanced materials efficiently; and, the development of new products taking advantage of the availability and cost-effectiveness of these highly engineered, advanced materials.

Jan 1, 1986

By C H. Dowding, P W. Linehan

Many of the technical and non-technical or human problems associated with blasting can be minimized through a proper preconstruction test-blast program.

Jan 1, 1986

By Frank F. Aplan, Edward C. Jr. Dowling, Richard R. Klimpel

Thirteen kinetic models that mathematically describe the flotation process have been statistically evaluated for the flotation of copper, lead and zinc ores. Comparisons have been made for a variety of circuits involving roughing, cleaning, scavenging and regrind followed by cleaning. Variations in collectors, frothers, depressants and activators have been considered. Based on the statistical criteria used for the evaluation, and the reagent, circuit and ore variations studied, the most reliable flotation models have been identified and subsequently used to characterize the metallurgical results.

Jan 1, 1986

Selective continuous surface mining is a rapidly developing system of mining which will have a significant impact on many present and future open cut mines. In many aspects the technology is in its infancy, whilst in other facets concepts drawn from other sectors of engineering are well proven. Full development of the potential and benefits of this technology will only be achieved if the mining companies and manufacturing companies work together to produce machines which the end user really wants.

Jan 1, 1986

By F. W. Benn

The Bureau of Mines investigated flotation methods for recovering fluorite and byproducts from two samples of the Fish Creek deposit in Eureka County, NV. The preferred method for tre.ating a fluorite-beryllium sample included (1) fluorite rougher and cleaner flotation, (2) desliming at 20 um, (3) muscovite flotation, (4) silicate flotation, (5) sodium hypochlorite wash of silicate concentrate, and (6) beryllium rougher and cleaner flotation from the silicate concen-trate. Laboratory results showed that over 94 pct of the fluorite was recovered in a recleaner concentrate containing 98 pct CaF2, Beryllium flotation produced concentrates containing in excess of 5 pct BeO with recoveries over 70 pet. The preferred method used for a fluorite-mica sample consisted of (1) fluorite rougher and cleaner flotation, (2) desliming at 20 um, and (3) mica flotation using an anionic-cationic collector system. Laboratory results showed that 84 pct of the fluorite was recovered in a recleaner concentrate containing 96 pct CaF2, Mica flotation produced a concentrate containing 95 pct mica at 85-pct recovery.

Jan 1, 1986

Intensive exploration for iron ore in the banded iron-formations (BIF) of the Pilbara region of Western Australia began in the early sixties and almost immediately established the Hamersley area as a major iron province. The early genetic models for the BIF-hosted ores were based mainly on macroscopic examinations of ores from the "hardcap" zone, and generally accepted a direct relationship with weathering effects on a Mesozoic to Tertiary land surface. Brandt (1964) was the first to suggest a difference in age between the high-grade hematite ores and the more common hematite-goethite types. He initially accepted a supergene origin for both, but later opted for a hydrothermal origin for the hematite ores. Apart from MacLeod (1966), the published views of the next decade reflect a largely parochial interpretation of individual ore bodies, centred mainly on supergene models but with some support for hydrothermal concepts. Except for Ayres (1971), none of the models were backed by detailed mineragraphic data. In 1976, an AMIRA-sponsored CSIRO group began a Province-wide investigation of the wide variety of ore types and BIF, with emphasis on geochemical and textural studies. The resulting conceptual model for a world-wide unified supergene and supergene-metamorphic hypothesis is generally accepted in the Hamersleys.

Jan 1, 1986

By P. Wieser, D. Feke

"Priming of filters with small pores is influenced by the surface tension of the liquid metal and may be complicated by freezing • Freezing followed by melting has been observed experimentally. This process has been modeled on the basis of one dimensional heat flow by radiation to the filter and by conduction in the metal. Also considered are super-heat of the metal and the initial filter temperature. The results of the model provide useful guidelines for the application of filters. IntroductionFiltration has been recognized as a valuable method of refining by removing suspended phases from liquid metals or alloys. Woven fiberglass type fabrics and wire screens were used initially in the aluminum industry. With the introduction of the ceramic filters that exhibit improved inertness and refractoryness, filtration has been introduced to higher melting alloys including cast irons, superalloys, stainless steels, as well as low and medium carbon low alloy steels. A considerable literature is delveloping rapidly on the progress in applications and the advances in understanding the mechanisms and effectiveness of filtration processes (1-8).With the use of filtration for different alloy systems for the production of cast to shape parts a bewildering variety of gating system modifications has been developed (Figure 1) to accommodate the installation of filters in the mold. The modifications have two principal purposes: 1) the runner expansion is intended to compensate for the resistance to flow due to the filter and that of the captured inclusions, and 2) the metal reservoir upstream of the filter, provides a temporary by-pass which permits metal to flow across the filter and heat it until priming can be accomplished. priming of.filters by low and medium carbon steel is readily accomplished but, compared to such alloys as cast iron or 19 Cr-9Ni stainless steel, requires greater precautions to avoid failure to prime by excessive freezing on or inside the filter pores. This problem is further examined below:"

Jan 1, 1986