Search Documents

Within the Mt Whaleback open cut mine the integrity of the final pit wall is achieved through careful rock slope design, use of rock reinforecement technology where marginal stability exists and use of controlled blasting techniques and excavation practices. By reducing the effective density of ANFO explosive within blastholes to around 0.2 glcm', and developing standard blast pattern designs for various rock types, blast damage to pit walls has been minimised. Accurate geological prediction is necessary for optimum blast design. Controlled blasting is undertaken where blasting occurs within 90 m of the designed final batter crest and hole by hole assessment of final limit blast patterns is undertaken before pattern charging. Shovels and trucks remove the bulk of blasted and dozed rock material, but due to the mine's variable pit wall slope configuration, bulldozer excavation of some critical design batters has been successfully Implemented.

Jan 1, 1986

By William F. Riggs

The characteristics of frothers can often be determined by the proper selection of various chemical groups. There are three basic groups utilized in the application of frothers. These are alcohols, polyglycol ethers, and polyglycols. Some of the chemical groups are separated in subgroups. Each chemical group provides particular characteristics which affect load support, bubble diameter, water retention, air dispersion, and kinetics of froth formation. These chemical groups may be preblended in various percentages to optimize frother characteristics for a particular ore deposit.

Jan 1, 1986

Jan 1, 1986

Registrations for the Congress were 393 asdelegates and 200 as accompanying persons.The breakdown of registrations by countries isshown in Table 1.

Jan 1, 1986

By C. D. Peters

The Bureau of Mines has been researching remote sensing analysis of an underground coal mining area in Utah and computer-aided methods of defining ground control hazards in this mining area. As a result of these studies, a preliminary potential hazards map was developed for the test site. This map is based primarily upon a lineament (linear feature) analysis of Landsat satellite data. Other data used were paleochannel location data, resistivity data, and information from surface and underground field checking of the lineaments and ground control problems in the mine. Lineaments proved to be reliable indicators of hazardous areas, although the type and degree of hazard varies with different lineament trends and the presence of other conditions such as lineament intersections and intersections with other geologic structures or with paleochannels. Lineaments were observed to match faults, joints, and/or joint trends in the area. The paleochannel data, derived from drill hole data, provided basic information about potentially hazardous areas in the mine by suggesting where paleochannels could cause instability in the roof rock. The ground control problem data served largely to define the relative degree of hazard associated with lineaments and the types of hazards encountered in the mine. Resistivity data helped confirm the presence of fractures where they were expected to occur both from surface geology and from the lineament data.

Jan 1, 1986

The estimation of local recoveries, such as the local recovered tonnage of ore and its corresponding grade at a given cutoff grade, is an important problem in a selective mining operation. Multigaussian kriging provides a simple solution to this specific problem. The solution is also complete in the sense that local recoveries are estimated together with their estimation variances. It is thus possible to assess confidence limit intervals on the estimated recoveries. Multigaussian kriging has been applied to the Jerritt Canyon deposit in a most realistic situation. The various steps of the estimation procedure are presented in detail and the potential of the method is demonstrated in view of the results. The obtained results show that the estimated recoveries are in good agreement with the actual recoveries and the actual estimation errors are correctly predicted by the estimation variances. Multigaussian kriging thus appears as a useful and fully operationable tool for the mining industry.

Jan 1, 1986

By C. T. Harper, B. J. Fryer, R. P. Taylor

"IntroductionThe Maurice Bay deposit is one of a number of uranium deposits that have been found in recent years in the Athabasca Basin of northern Saskatchewan (Tremblay, 1982). This deposit, along with the others, belongs to the unconformity type deposits (Beck, 1977). They are, for the most part, polymetallic, being characterized by a suite of metals which include U, Ni, Co, Cu, Pb, Zn, Mn, V, Ag, Au, Pt-group elements, S, As, Bi, Se, Te, and Mo, some of which, besides U, are present in economic concentrations (Amok, 1974; Ruzicka, 1975; Tapaninen, 1976; Hoeve and Sibbald, 1978; Dahlkamp, 1978). The Maurice Bay deposit was known to be a small low grade deposit in which the ore was essentially monomineralic, consisting mainly of pitchblende (Harper, 1978). However, the occurrence of trace amounts of some of the elements common in the larger polymetallic ore bodies (e.g. Key Lake, Cluff Lake D) was anticipated. Thus a lithogeochemical sampling project was undertaken in 1979 across part of the Maurice Bay deposit (Harper, 1979). Major oxides (SiO2, Al2O3, FeO, Fe2O, MgO, CaO, K2O, Na2O, MnO, P2O5, and TiO2) and a group of the most common trace metals (U, Ni, Co, Cu, Pb, As, Au, V, and Se) were analyzed to determine whether any elemental patterns (halos or depletions) could be detected which would reduce the number of pathfinder elements needed for exploration purposes. In addition to the above metals, Th was also checked because some conglomerate strata in the Maurice Bay area are known to be thorium-enriched (Harper, 1978). Only the trace metal distributions will be discussed in detail in this report.General GeologyThe Maurice Bay area is underlain by three major groups of rocks, the White Lake metamorphic complex, an unnamed granodiorite complex, and the Athabasca Group, described previously (Fig. 1; Harper, 1979). Table 1 summarizes the stratigraphic features as deduced by geological mapping and the examination of drill cores."

Jan 1, 1986

By [Miroslaw] M. Hajdasinsk

The identification of the real internal rates of return (IRR's) of a project is essential for its economic evaluation. The existing methods for the calculation of IRR's are both cumbersome and unreliable, mainly because of their inability to effectively isolate the real IRR's and incapability of discovering multiple IRR's of even multiplicity. In this paper, a concept of the 'cash flow pattern tree used for isolation of the real IRR's of a project is presented. This concept, combined with the Sturm procedure for counting the real distinct zeros of a polynomial within a specified interval, leads to the development of a method and computer program for isolation and calculation of the real IRR's of a project. The method examines whether or not real IRR's exist, and if they do, isolates them within bounded and narrow intervals in a mathematically founded way. The isolated IRR's, whether simple or multiple, are subsequently calculated either directly or by means of an appropriate approximation procedure. Numerical examples assist the development of the method and the corresponding computer algorithm. Because any Net Present Value treated as a function of interest rate can easily be transformed into a polynomial, the method presented also constitutes a method for finding the real zeros of a polynomial.

Jan 1, 1986

By D. D. Marsden

This paper discusses the concentrations of sulphides and total sulphur in widely spread regions around mine residue deposits, from which rain-water run-of can enter the Vaal River system. Analyses of borehole samples from several deposits are used to establish typical sulphur head grades. It is shown that a high percentage of al the oxidizable, and hence leachable and pollution-causing, sulphur has already been removed. When the residues were fresh, water that came from the deposits was highly polluted, but the dissolved solids from these residues are today of very minor significance. The data are supported by analyses of the drainage streams.

Jan 1, 1986

By A. Sainato, E. Baker, J. Cervik

In Europe, water infusion is used widely to reduce generation of respirable dust during mining. Its use in the US is limited to a few plow operations in the deeper parts of the Pocahontas No. 3 Coalbed. The technology for infusing water into retreating longwalls is described and results of a recent Bureau test in the Lower Sunnyside Coalbed demonstrated dust reductions ranging from 47% to 64%. Because water infusion increases moisture content of the coalbed, face air velocities in excess of 2.5 m/s (500 fpm) are possible, further diluting dust levels before dust entrainment occurs. An economic analysis shows a 23% reduction in operating costs when coal production is increased by changing from unidirectional to bidirectional mining with water infusion.

Jan 1, 1986

By I. Iwasaki, K. A. Nataratjan

In a previous paper, ozone was shown to remove residual xanthates in flotation pulp solutions as well as to destroy the xanthate coating on bulk copper-nickel sulfide concentrates before differential flotation (Iwasaki and Malicsi, 1985). The oxidation and decom- position mechanisms of xanthate solutions in the presence of commonly used oxidants such as oxygen, chlorine, hypochlorite, bromine, iodine, and hydrogen peroxide at different pH levels have been reported in the past (Rao, 1971). Most of these studies have been restricted to xanthate solutions of pH less than 10. Very few references are available on xanthate decomposition in highly alkaline (pH > 12) solutions (Jones and Woodcock, 1983; Philipp and Fichte, 1960; Tipman and Leja, 1975). No systematic study of xanthate oxidation by ozone has been reported, although its use in flotation has been recognized of late (Allegrini et al., IWO; Ishii et al., 1970; Matsubara et al., 1978). To improve the efficiency of ozone use in flotation, it is essential to understand the mechanisms involved in the decomposition of xanthates with ozone, more specifically, to establish the stoichiometry and decomposition rate. In the present work, a preliminary attempt was made to investigate the effect of pH on xanthate decomposition, and probable mechanisms of xanthate oxidation with ozone.

Jan 1, 1986

By G. T. van Rooyen

The susceptibility of a low-alloy steel that has been hardened and tempered-826 M40 (EN26)-to embrittlement by strain aging during service was simulated by artificial aging of specimens at 100°C. It was found that the brittle transition temperature of both monotonic and cyclically strained material was increased by only about 25°C as a result of strain aging. It is concluded that the susceptibility of low-alloy steels in the hardened, tempered condition is less than that of low-carbon steel, and that such steels qualify for exemption of the periodic 'annealing' required by the Mines and Works Act.

Jan 1, 1986

By V. W. Smith

For the past 50 years, the primary crushing of stone at the Dolase Bros. Co. Richards Spur Quarry. 13 miles north of Lawton, Oklahoma, has been accomplished by a Traylor 42-inch gyratory crusher. The production capacity of the primary system, consisting of a feeder, grizzly, and the gyratory crusher, was approximately 2100 tons per hour. Shot-down scone was hauled from the working face about one mile to the feeder by a fleet of Caterpillar Model 773's and WABCO 60- and 65-ton trucks. In order to maintain production, nine to ten trucks and four Caterpillar Model 992 front-end loaders were required to be operational at all times.

Jan 1, 1986

By J. C. Danza Errico

The bauxite deposits on the Pocos de Caldas Plateau in the state of Minas Gerais, Brazil, were formed by the differential weathering and leaching of alcaline rocks in a ring structure. Their action on steep topography formed heterogeneous ore posture and chemical grades. Variographic analysis of several of these deposits show nested structures that are probably related to ore genesis. Kriged ore reserves estimation are presented with emphasis on the data pro cessing method that was employed. Programs were written in APL. Its intrinsic use of matrices contributed to faster programming and less computer time. In many cases looping was eliminated. The high resolution graphic resourses of APL. workspace facilitated programming of variogram analysis, fitting, and regularization. APL sub-routines are presented for variogram calculation and kriging.

Jan 1, 1986

Pictured on these pages are the six RMCMI Scholarship Award Winners for the 1986-87 year followed by a brief profile. Five of the winners were present as RMCMI guests at the June convention at Kalispell to receive their recognition plaques at the welcoming session held Monday, June 30, 1986. In addition to the plaques, each winner will receive $500.00 to be used toward tuition in the coming academic year. Also, as this is a continuing award, the winners from the 1985-86 season, will also receive an additional $500.00 for tuition use in their senior years provided they have maintained a good academic standing. Criteria for these awards is (1) That the award be made in the spring to a sophomore student to be used toward tuition during the junior year. (2) That the recipient be both a U. S. citizen and a resident of the state involved. (3) That the recipient have good academic standing, be pursuing a degree in a mining related field and have an expressed interest in Western coal as a possible career path. Contributions to this worthy project are tax deductible to each individual RMCMI member. Checks payable to RMCMI Scholarship may be mailed to the RMCMI Office at 2700 Youngfield Street, Suite 100 in Lakewood, CO 80215. Profiles of the 1986 winners follow: [ ] ROBERT BAUGHMAN Colorado School of Mines, Golden, Colorado Bob is spending this summer in field camp at the Colorado School of Mines. His hobbies are fly fishing, hunting and photography. After graduation, he "would like to work for a stable mid-sized company and someday work his way into a management position." He is a member of AIME and Sigma Phi Epsilon and plays intramural football and softball. [ ] BRENT LaMOURE Montana College of Mineral Science & Technology, Butte, Montana Brent has a 3 5 grade point average and has completed courses In Mining Engineering, Underground Mining, Rock Fragmentation, Mineralogy and Petrology and Plane Surveying He is "interested in trying to make the mining industry as efficient as possible "

Jan 1, 1986

By T. W. Turk

Iron Mountain Mines, Inc., (IMMI) ore de- posits are located in the southeastern portion of the Klamath Mountains in the West Shasta copper/Zinc Mining District in Shasta County (Figure 1). The original massive sulfide ore deposits totaled 22,895,000 Mt (25 million st). The remaining ore deposits contain 12,875,000 Mt (14,183,000 st) of proven massive sulfides and 2,769,000 Mt (3,050,000 st) of proven gossan deposits. The addition of magnetite deposits and tailings (now marketable) brings the total of proven and probable reserves to 20,433,000 Mt (22,508,000 st). The massive sulfide ore bodies are generating a natural flow of acid mine water which has been slowly leaching minerals out of these deposits. This flow varies in volume, depending on rainfall, and contains variable concentrations of copper, zinc, iron and precious metals. This mine water has been treated for the past 50 years at the mine site to remove copper. The treatment process, utilizing scrap iron precipitation, continues at a production rate of approximately 54,430 Kg (120,000 pounds) of copper precipitate annually.

Jan 1, 1986

By Leland L. Mink

Open-pit mining is sometimes conducted in areas where the artesian pressures contained in aquifers underlying the pit's floor are great enough to cause floor heave. In order to reduce this pressure several methods are commonly used. One of these methods is a pressure relief well or depressurization wick. The wick consists of a borehole which is filled with gravel and cased at the surface. The wick is allowed to flow freely, thus reducing pressure near its location. The spacing and depth of these wicks can be determined by a simple analytical and graphical technique which considers the weight of material overlying the aquifer and the artesian force within the aquifer. An example of the technique using data from a Colombian coal mine is presented.

Jan 1, 1986

By R. F. Engler

"IntroductionThe Coal Branch region of west-central Alberta has been the focal point for unprecedented exploration and development activities over the past ten years prompted by the renewed markets for high-quality thermal coal. Although mines were developed and operated extensively throughout the region from 1910 until 1960, information relating to the detailed stratigraphy of the coal measures and their areal distribution tended to be localized to individual mine sites. Continuity along trend was impaired by a paucity of outcrop restricting geologic mapping to stream bank and roadside exposures. Recent studies and subsequent publications by Jerzykiewicz and McLean of the Geological Survey of Canada (1978, 1980) have established a detailed sedimentological model and defined the stratigraphic nomenclature for the region . The term Coalspur Beds has been adopted to describe the coal-bearing sequence between the overlying Paskapoo Formation and underlying Brazeau Formation. Complete sections of the Coalspur Beds have been compiled from sub-surface borehole data and published by Manalta Coal Ltd ., Dentherm Resources Ltd. and Luscar Stereo Ltd. This paper is an attempt to correlate this information on a regional basis to illustrate trends within the Coalspur Beds."

Jan 1, 1986

The Sydney Coalfield, Nova Scotia contains extensive undersea longwall mining operations which are expected to continue well into the 21st Century. A long term research program has been initiated by the Cape Breton Coal Research Laboratory to investigate the full spectrum of problems associated with undersea mining and develop specific guidelines for use by the mine operator. At present, research is centred on the detailed evaluation of existing undersea sub- sidence guidelines, the identification and development of instrumentation capable of moni- toring seafloor subsidence profiles and the effective sealing of offshore exploration boreholes. In addition, work is also planned to examine in situ strata permeability changes occurring between the mining horizon and seabed and the feasibility of using artificial islands.

Jan 1, 1986

By Aaron Morales

El presente texto analiza la crisis minera -en tanto remite más que un problema de cotizaciones- y señala el error en el concepto de administración como una de las fuente de esta crisis minera. Así los recursos mineros con que cuenta un Estado debe concebirse con cuidado y trabajar con innovación las proyecciones más tangibles. De otro lado, se plantean soluciones desde la metalurgia y así utilizar con ventaja los recursos naturales del país -particularmente los carbones-.

Jan 1, 1986