Search Documents

By R. W. Smith, Z. Sadowski

The stabilities of finely divided mineral suspensions were determined as functions of pH and concentrations of polyethylene oxide, sodium ligninsulfonate, sodium dodecybulfate, and sodium oleate. In addition, the electrokinetic potentials of the minerals were determined under identical pH and additive concentration conditions. Flocculation or dispersion of the suspensions is discussed in terms of both the amount and manner of adsorption at the appropriate solid-liquid interface as it is influenced by additive concentration and pH.

Jan 1, 1986

By James C. Cawley

The Bureau of Mines conducted an investigation to statistically determine the mean current or voltage for resistive, inductive, and capaci-tive circuits that would cause spark ignitions in 8.3% methane-air, 5.3% propane-air, and 7.8% ethylene-air mixtures. Each mean ignition current or voltage was determined on the basis of 100 trials. Each trial consisted of 400 revolutions, 200 in each polarity, at 80 rpm of the standard breakf1ash apparatus. In general, spark ignition curves published in UL 913 for resistive and inductive circuits represent approximately the mean current values determined in this study, while published capacitive circuit values in methane are considerably less than the mean voltage values from this study, especially for a capacitance of less than 100 ~F. For resistive and inductive circuits, spark ignitions were obtained at currents con-siderably below those in the published curves, but this study was not optimized to find minimum ignition values. This report defines "safety factor" as applied to intrinsic safety testing as the energy ratio of the mean values of ignition current or voltage for two test gases. The safety factors presented in this report are not constant with voltage or current and, therefore, are not recommended for use.

Jan 1, 1986

By A. D. Fernie

Growing interest in pit crushing and conveying is evident from the recent many articles, technical papers, and new equipment development. Application of a pit crushing and conveying system is complex. Many factors, such as mine design, production scheduling, as well as initial and ongoing capital and operating costs must be thoroughly and realistically examined. This paper will address the fundamentals to be considered and review several approaches to developing a total system for a new and existing mine situation. The planning function will be outlined and operating and design criteria defined to interface the mining operation and the pit crushing conveying system.

Jan 1, 1986

By R. H. Mullennex

Application of depositional analysis concepts is becoming an ever-increasingly more important and more useable tool in exploration and development of coals in the Appalachian basin. Over the past decade, a rather large number of studies, papers, and publications have addressed various aspects of depositional environments of coals and, to some extent, applications to development. As would be expected as regards a subject so complex as Pennsylvanian sedimentation in the Appalachian basin, certain academic studies have produced conclusions at variance in some aspects to those of other studies. Overall, however, there has been a building- block progression and general refinement with time of understanding of the depositional settings and other factors controlling Appalachian coal distribution, quality, and other minability parameters. Most attempts to explain coal seam characteristics have revolved around a basic deltaic model. Some have attributed certain seam attributes to upper delta plain deposition, other attributes to transitional-lower delta plain settings, and yet others to lower delta plain environments, and so on. While these approaches have provided valuable insight into some general coal characteristics, they are somewhat incomplete and are, in a sense, too broad for specific mine-scale applications. Further, it is apparent that in order for widespread peat accumulation to occur, there must be a drastic decrease in the energy of the depositional system and amount of sediment being brought in, compared to the active deltaic and coastal processes responsible for deposition of the large volume of clastic sediments that dominate the Pennsylvanian system of the Appalachians. Consideration of this fact implies that peats (coals) may not necessarily reflect depositional settings that are directly coincident with those associated with adjacent rocks. Cecil and Englund (1985) address this point, and quite correctly state that "the primary controls on major stages of peat formation are allocyclic processes involving paleoclimate, eustatic changes in sea level, and tectonics." While this statement is inarguable, it does not negate the importance and usefulness of depositional analysis in predicting reserve characteristics that may impact mining and marketability.

Jan 1, 1986

Robert Rampton Porter died on 8th September, 1985, in Salt Lake City, Utah, at the age of 75. Bob Porter was born in Salt Lake City in 1910, and he attended the University of Utah, where he obtained an M.Sc. degree in metallurgy. Galvanizing In conjunction with the National Institute for Materials Research of the CS I R, the South African Hot-Dip Galvanizers' Association has organized the First International Conference on Galvanizing in South Africa. This event will take place at the C SIR Conference Centre in Pretoria from 3rd to 7th November, 1986. Environmental effects of mining A one-day meeting entitled 'The environmental effects of mining and restoration' will be held on 23rd September, 1986, at the University of Manchester Institute of Science and Technology, Manchester, England.

Jan 1, 1986

By J. S. Whatley

The properties, origin and industrial uses of kaolin clay are briefly reviewed. The general waterwashed beneficiation process is described. Yost aspects of filtration and solids-liquid separation as practiced in the kaolin industry are mentioned along with devices that are currently in the developmental stage. The paper focuses heavily on the well known art of rotary vacuum filtration, including general construction and operating details. Devices under investigation that might be used to mechanically or electrically dewater clay slurries to higher cake solids levels than can be achieved with rotary vacuum filters are described briefly.

Jan 1, 1986

Provide mine safety personnel, MSHA inspectors, and original-equipment manufacturers with guidelines and a check list for inspecting rollover protection structures (ROPS) being used in mining operations. The Problem ROPS are provided on mobile surface mining equipment to protect operators from such safety hazards as machine rollovers, falling objects, and collisions. However, the protective capability of a ROPS can be greatly reduced if it is damaged. Certain kinds of damage, such as hair- line cracks, corrosion, and loosened bolts, may occur as a result of normal machine use but may not be recognized as unsafe by untrained personnel. Therefore, the Bureau of Mmes designed a manual which can be used by mine personnel when inspecting ROPS equipment. The Manual The manual was prepared to help acquaint mine safety personnel and MSHA inspectors with typical ROPS deficiencies and their causes. It provides a systematic means for inspecting ROPS so that the identified deficiencies and their causes can be corrected. It is suggested that an inspection of the ROPS be conducted after every 1,000 h of equipment operation, or sooner if the structure has been subjected to any unusual loads which could cause damage, such as a rollover, highwall caving, or collision. The manual also details common deficiencies in the structure and attachment hardware which may affect the service life. The checklist, when used as instructed in the manual, provides a means for systematically inspecting the structure to ensure maximum protective capability and conformance with applicable Federal regulations.

Jan 1, 1986

By S. E. Clay

In the chemical reaction control regime employed in the laboratory dissolution experiments, calcined trona ore dissolves in aqueous solutions according to a first order, irreversible reaction rate. The study showed that the reaction is first order with respect to solution NagCO3 concentration. The activation energy was determined to be 20.233 kJ/g. mol with a rate constant equal to 1235 mm/s (2917 in. per min). The dissolving particle may be described by shrinking particle behavior.

Jan 1, 1986

By P. J. Bethell

In the froth flotation process the detrimental effect of slimes on the froth flotability of valuable minerals has long been known.1 Work by Aplan2 on the froth flotation of coal has shown that the presence of clay slimes causes loss in flotation selectivity, and recovery of combustibles. Obviously then the presence of clay slimes to any great extent in the froth cell feed in a coal preparation plant is undesirable. This problem is exacerbated in plants treating raw 600 um (28#) by zero material due to the variation in flotation with size. The net effect of this phenomenon in a bank of cells treating raw minus 600 µm (28#) material s that by the time adequate flotation of the coarsest size fractions has occurred the finer sizes are already producing undesirable high ash material, which often leads to unacceptable overall quality. Reduction in aeration rate and/or chemical addition to combat this, further decreases the flotation rate of the coarsest fraction leading to heavy losses of coarse low ash coal to the tailings. The above mentioned characteristics formed a key aspect of the fine coal circuitry design at Elk Run Coal Company in Sylvester, WV. The plant was designed to produce compliance steam coal (less than 1.20 lbs. S02/million b.t.u.) Desliming ahead of the froth flotation was included, as the slimes in the plant feed were clay rich, had very high ash levels, and low potential recovery. Lab testwork had also shown that poor selectivity would be expected if raw minus 600 um (28#) material was froth floated.

Jan 1, 1986

By M. A. Greenwood

The total value of coal, FOB mine, consumed in the United States was $21 billion in 1985. Roughly $6 billion was spent to transport coal from the mine to the consumer by rail. This indicates the impact railroad transportation has on the competitiveness of U.S. coal as an energy resource. Actually, this is just the tip of the iceberg. When you consider the largest U.S. reserve of coal, the Powder River Basin, which is possibly the lowest cost coal in the U.S., or maybe even the world, the transportation cost is the overriding factor in developing competitive pricing. Rail transportation costs from Powder River can be multiples of 2, 3, or even 4 times the cost of coal FOB mine. About sixty percent of all U.S. coal is shipped by rail. In the case of Powder River Basin coal and many other reserves there are no current alternatives to rail. Are there feasible alternatives to rail transport?

Jan 1, 1986

By Pattinaja MA

Mathematical modelling was carried out to determine the probable convergence and vertical stress patterns around a retreating longwall panel in an underground coal mine in New South Wales. An 'Electrical Resistance Analogue' and a program called 'THREED' based on the displacement discontinuity method were used for the modelling. Parts of the obtained results are presented here and compared with some measurements of convergence at the site. The modelled and measured data agree better qualitatively, than quantitatively.

Jan 1, 1986

By Edwin H. Bentzen, Immo H. Redeker

Important industrial minerals are separated and concentrated by froth flotation by industry today. The following descriptions are presented as an overview of the methods employed to separate and recover a few of these industrial minerals. The minerals described in this section of the book are not, by any means, the only important minerals treated by froth flotation. Other minerals, such as calcite, kaolin, wollastonite, rare earths and vermiculite were not included, primarily due to the confidential nature of the information held by the Minerals Research Laboratory and the Colorado School of Mines Research Institute. Flotation of nonmetallic minerals is sometimes viewed as alchemy. However, the art is, in reality, based on sound chemistry, experience and a little luck in the treatment of new ores. In the flotation of nonmetallic minerals, as opposed to base metal sulfides, highly specific treatment conditions are required to accomplish separations. The presentation of the treatment of each of the minerals described was outlined as follows: DEPOSITS PROCESSING SPECIFICATIONS FLOWSHEETS (in some cases) A presentation of the factors, often critical, which must be carefully investigated to accomplish successful flotation of nonmetallic minerals is presented in the section on Sulfonate Collectors, elsewhere in this volume.

Jan 1, 1986

By Bonnie A. McGregor

The U. S. Geological Survey in cooperation with the Institute of Oceanographic Sciences (IOS), U.K., conducted a sidescan sonar survey of the U. S. Exclusive Economic Zone in the Gulf of Mexico from August 7 to October 22, 1985. A reconnaissance-scale view of 120,000 square nautical miles of sea floor seaward of the shelf-edge was obtained by using the GLORIA (Geologic Long-Range Inclined Asdic) sidescan sonar system. After these data were merged with GLORIA data from an earlier survey (1982) of the northwestern Gulf, a preliminary mosaic was constructed at a scale of 1:375,000. From this mosaic, we can identify morphologic features and interpret sea-floor processes. The extensive deformation of the continental slope seaward of Texas and Louisiana by salt tectonics has resulted in a complex pattern of basins and salt dome highs. One continuous meandering channel was identified in this portion of the Gulf, extending from the shelf edge to the Sigsbee Abyssal Plain. Bottom currents have reworked the sediments in this channel's levees seaward of the Sigsbee Escarpment, the seaward edge of the salt front, suggesting that this channel may no longer be actively transporting sediment. Talus appears to lie along the base of the Sigsbee Escarpment, suggesting that erosion and deposition is occur- ring along this front. Three other discontinuous channel systems can be identified on the mosaic and appear to have contributed sediments to the deep Gulf.

Jan 1, 1986

By Dennis Z. Mraz

Subsidence profiles over Saskatchewan potash mines exhibit forms which cannot be explained by existing subsidence models. The subsidence is affected by bridging of competent rocks. A modification of the theory can explain the observed displacement of subsidence profiles due to bridging. An unusual shallow secondary subsidence trough has been observed extending two to three kilometers outside the primary subsidence. The secondary subsidence is explained as an elastic compression inresponse to a drop in pore water pressure in the vicinity of the caving zone. The concept of pore water pressure may lead to a safe extraction limit for Saskatchewan mines.

Jan 1, 1986

By William A. Travnik

For more than 60 years, ESSO RESOURCES CANADA LIMITED has been producing and refining oil at a small refinery in Norman Wells, Northwest Territories, and supplying diesel fuel and other oil products to northern markets. In 1982,ESSOwas granted governmental approval to expend production from the oil field from 475 cubic metres a day to 4400 cubic metres a day. This $800,000,000projectproceeded ahead of schedule for a start up in 1985.

Jan 1, 1986

By Stephen C. Tadolini

The anchorage capacity of four types of bolting systems was investigated in two mines with thick coal roofs. In conjunction with the in-mine tests, a simple axisymmetric finite element computer program was developed. Both the field and computer results indicated that thick coal roofs can be effectively supported entirely by the coal member.

Jan 1, 1986

By D. H. C. Griffiths, D. R. Davis, D. B. Paterson

Consolidated Murchison Limited is the only primary producer of antimony in South Africa, producing approximately 18 per cent of the total world production. This paper gives a technical review of the history, occurrence, mining, and metallurgy of antimony at Consolidated Murchison. World antimony markets are also discussed, together with the end-uses.

Jan 1, 1986

The main goal of this paper is to present readers with recommendations for choosing coaxial cables appropriate for mining applications of Time Domain Ref 1 ectometry (TDR) to monitor rock mass movements. Prior to discussing the recommendations, mining applications are illustrated with examples and the operating principle of TDR is discussed briefly. Items that affect the result of the monitoring system performance include the coaxial cable selected, the grouting material used, and the installation procedure.

Jan 1, 1986

The great philosopher, Marshall McLuhan, is said to have stated that the use of forecasting as a means of guiding future actions is akin to driving an automobile through observations made in the rear-view mirror! In effect, in forecasting it is assumed that there will be an orderly progression from the past into the future, and that the model will be sufficiently unvarying for use to gauge both the directions and the rates of change. The concepts of forecasting have served man well in disciplines in which the relationship between causes and effects can be clearly demonstrated; such as between rainfall and crop yield, for example. These are of no value, however, when conditions change rapidly and unpredictably, or when there is no model at all. Even worse, under such circumstances our preconceived notions may cause us to make some horrendous errors in judgement. Such are the risks at present in attempting to make an assessment of the educational needs of the minerals industry for the coming century! The model, and the conceptions that we have had of the linkages between cause and effect are in disarray. Minerals markets are chaotic, and there is almost no ability to forecast trends in metal values. Linkages between supply and demand seem tenuous. Internationally, producers are struggling for survival. Mine closures, temporary shutdowns, and reopenings are frequent occurrences. Decision-making under uncertainty is probably one of the most certain things about the world mining industry Today!

Jan 1, 1986

By T. Cyrul

The Polish underground mining has its long lasting tradition. High production of coal, that has recently been approaching 200 milion tons per year, put this small country among the bigest world producers of coal. To achieve such a high production, which mainly originate from very unfavourable mining and geological conditions, Polish scientists and engineers have to introduce new and original solutions to the mining practice. Many of the solutions on mining methods, ventilation, stability, subsidence etc., have had the world wide reputation, however, insufficient translations from Polish cause , that many of the recent Polish mining achievements are not known to foreign specialists.

Jan 1, 1986