Search Documents

By Christopher J. Bise

INTRODUCTION Before a mine is planned in detail, a preliminary analysis is often conducted. This preplanning permits the mining engineer to make a rapid assessment as to whether or not a particular mining property warrants further consideration. In fact, a properly conducted preplanning phase can come within 10% to 20% of the actual results, thereby saving the mining engineer valuable time before committing himself to a fine-tuned analysis. The questions to be answered by mine preplanning are (1) What will be the operating conditions for the mine? and (2) How long will it take to complete the project? To answer these questions, calculations dealing with reserve estimation, production planning, man- power planning, and project scheduling are conducted. The following sections discuss these various phases of mine preplanning in greater detail. RESERVE ESTIMATION The estimation of the various characteristics of a reserve, such as quantity, grade, and thickness, is an ongoing process throughout the life of a mining venture. However, the reserve-estimation phase of mine planning is more closely associated with the preplanning phase. There are many different techniques employed in reserve estimation of solid mineral deposits; variations among them are introduced because of such considerations as ease of application or level of accuracy. In any event, each technique is developed in the following manner: (1) the mineral body is represented pictorially and then subdivided into blocks related to one or more samples of exploration data, (2) the area and volume of each block is determined, (3) the volumes are converted to representative tonnages (or, for example, grades), and (4) the results are tabulated. To illustrate this procedure, the polygonal (area-of- influence) technique will be presented due to its ease of application, flexibility in dealing with different deposits, and general acceptance. The polygonal method assumes that all characteristics of a mineral body extend halfway between a point of observation and any other point of observation. The explored portion of the mineral body is represented by polygonal prisms whose depths relate to the characteristic in question (grade, thickness, etc.) and whose plane bases relate to the area of influence of each point of observation (drill hole, etc.) as shown in Fig. 1. The polygons must be constructed in a definite order, usually clockwise and from the periphery to the center of the deposit. Table 1 can then be used to calculate the characteristics in question. Since, by definition, the polygonal method assumes that the characteristics of a mineral body extend half- way between points of observation, it becomes readily apparent that the evaluation of a vertical-drill hole exploration program requires that the sides of the polygons be formed by the intersection of perpendicular bisectors (Fig. 2). Figs. 3 and 4 show correct and incorrect construction of the polygons. The criterion for correct construction of the polygons is that all points within a particular polygon must be closer to its rallying point than those located in any other polygon. This is clearly not the case for certain points that are located in the polygon containing rallying point B in Fig. 4. Although this method can be used where the drill holes are irregularly spaced, calculations become less tedious when a square net (Fig. 5) or a chessboard (Fig. 6) grid is adopted. The numbers shown in Figs. 5 and 6 represent the relative weight for each of the shaded areas. In general, the greater the number of polygons, the more continuous the mineral body, and the more regular the grid, then the more accurate the computations will be. PRODUCTION PLANNING Before an acceptable evaluation of the production potential of a mine can be determined, a thorough exploration program should be conducted. It seems obvious that the nature and properties of the deposit and adjacent strata, the presence of impurities, and other mining conditions should be adequately determined prior to production planning and equipment selection. The lack of sufficiently detailed knowledge of the many mining parameters has led to the failure of numerous operations. For example, targeted production tonnages and equipment sizes for a coal mine are intimately related to the seam thickness. Needless to say the quality of information that is gathered from an exploration program can have a tremendous impact on the production plan. Production plans are developed initially by determining reasonable shift tonnages per operating section. Most of the time these values are developed from his-

Jan 1, 1986

By G. K. Ruhlandt, C. W. Kim

"A 3-D Finite Element Method program called ""SOLCAST"" has been developed to simulate the casting solidification process. Using the temperature recovery method to evaluate the latent heat of fusion and applying a new combination of the time integration scheme, SOLCAST reduces the computational time significantly compared to an existing commercial FEM program, and produces accurate results comparable to experimental casting results. Prediction of casting shrinkage porosity for A390 aluminum alloy will also be discussed. To make this FEM program useful for foundry engineers, this program was connected to a commercial pre- and post-processor.IntroductionBecause of recently increased competition, foundrymen must produce high quality castings more economically. Therefore, casting solidification analysis prior to casting production is an attractive way to reduce costs and development time.Although the actual casting solidification process is a very complicated phenomena, foundrymen could predict where shrinkage defects would occur based on a transient conduction heat transfer analysis that includes the liberation of latent heat. A numerical analysis is generally required to solve the heat diffusion equation with the latent heat diffusion term, because casting shapes are very complicated and pure materials are rarely used.Different numerical methods have been applied to the casting solidification analysis 1. Among them, a finite difference method 2 and a finite element method (FEM)3 are most commonly used.Each simulation method has one or more basic difficulties which are different for each method. These difficulties are:(1) Modeling casting shapes on a computer.(2) Time consuming computation.(3) Uncertain material properties."

Jan 1, 1986

By S. K. Kawatra, Harrison R. Cooper

In the last 30 years, on-¬stream slurry analyzers have proven to be of great use in the control of mineral processing circuits. This review discusses the two most popular methods, x-ray fluorescence and neutron activation analysis, and also considers techniques which are still under development.

Jan 1, 1986

By Michael R. Birkos

A new electrotelluric prospecting technique allows the mapping of ore body distribution, lithologic contacts, and voids with accurracy comparable to core drilling. Data is available almost immediately and presented in a format similar to a downhole log. This is done with a passive surface receiver that transduces electrotelluric radiation into an audible signal. Changes in the character of the audible signal lends insight into lithology, porosity, fluid type and medium. Three case histories are presented. The first delineated a paleochannel within a coal seam. The second traced old mine workings and backfill areas. The third identified a high-pressure karst void.

Jan 1, 1986

Gas dynamic phenomena, particularly instantaneous outbursts of coal and gas are problems experienced in gassy, highly stressed coal, both usually the result of depth. Diff- erent mining geometries present different opportunities for seam gas to escape, starting from the virgin condition unaffected by mining and ending with the mining of the coal. The mining of the coal varies from entering a virgin seam cross-measure, heading out into virgin seam, advancing longwall faces into virgin seam and extracting developed blocks from large longwall retreating blocks to small pillars. Each method has its particular gass- iness patterns and particular stress patterns, both changing to some extent with time, and changing as mining progresses. Geological structural anomalies are the cause of gas and stress anomalies, causing in turn greater gas and stress manifestations. Pre-drainage of gas from the working seam not only degasifies the coal but causes it to shrink and so may affect stress as well as gas patterns. Unfortunately prior degasification is not all benefit, and there are some d13- advantages to its use. Also although it is possible to degasify places ahead, gassiness will return if drainage holes are shut down or sealed up and other deleterious aspects may be induced. Research should continue into the problem of instantaneous outbursts of coal and Gas.

Jan 1, 1986

By S Lukovic, Vishwa Bhushan, Calvin J. Konya

Effect of each of these variables has been well characterized for ANFO. This paper presents results of underwater energy measurements for one watergel and one emulsion type of slurry explosive which were initiated by 3 types of initiators (one electric and two cords of different strength) in 2 and 3 inch diameter steel pipes. Results of this 2 x 3 x 2 factorial experiment show the effects of detonating cord on energy released by the watergel and the emulsion explosive. Effect of diameter and its interaction with cord strength have also been characterized for the two explosives.

Jan 1, 1986

By A. G. Journel

Accurate prediction of recoverable reserves are key to the development and planning of a mining operation. Recovery functions for tonnage, quantity of metal, and ore grade are defined and two approaches for their estimation are proposed. The indicator kriging (IK) approach draws on the data rank orders, whereas the multigaussian (MG) approach relies on a grade multivariate distribution hypothesis. Although based on different premises, both approaches yield remarkably similar, and reasonably accurate, estimates for recoverable reserves.

Jan 1, 1986

Rockbursts, as they occur in South African deep level gold mines, have a lot in common with natural earthquakes. Both violently release seismic energy and cause damage to underground and surface structures. Rockbursts are the main cause of fatalities in deep gold mines and the problem may increase in severity with future mining at greater depths. Although the emphasis in Rock mechanics is on the prevention of rockbursts, prediction would provide a partial solution to the rockburst problem. A research project was initiated in 1981 on Western Deep Levels to investigate the possibility of detecting and identifying precursive microseismic activity. This project has succeeded in locating potential sources of seismic events with reasonable confidence. The timing of these events may be estimated with less confidence, and an important parameter, namely the potential size of the rockburst, still cannot be determined. An example of a large seismic event and its associated precursive activity are discussed. Practical prediction systems will, at least for some time, involve subjective decision making which will place a new responsibility on the mine manager as well as the rockburst specialist. The moral pressure on the manager as the final decision maker will probably be greater than the fear of leqal prosecution.

Jan 1, 1986

By Keith A. Heasley

At this point in time, approximately 800 M tonnes (880 M tons) of coal are mined each year in the United States. Forty percent of this coal or approximately 320 M tonnes (350 M tons) is taken from underground coal mines, and from this subtotal 16% or 50 M tonnes (55 M tons) is from longwall panels (1). If, for the sake of argument, an aver- age extraction thickness of 1.5 m (5 ft), an aver- age extraction ratio of 50 percent and an in situ density of 1360 kg/ms (85 lb/ft3) for this coal are assumed, then the 320 M tonnes (350 M tons) of underground coal translates to over 310 km2 (76,000 acres) that is undermined each year. Con- sidering that the total U.S. production of under- ground longwall coal to date is approximately 345 M tonnes (380 M tons), then a total of approximately 165 km2 (41,000 acres) (considering 100% extraction) has been directly undermined by longwall coal production in the United States. If the angle-of- draw is considered, the total area affected by longwall subsidence in the United States is probably twice the above value or 330 km2 (82,000 acres) . In the future, a number of other miscellaneous factors seem likely to multiply the number of potentially damaging situations that occur due to longwall coal mining. First, the overall production of coal in the United States is expected to gradually increase. This factor is further com- pounded by both the fact that the percentage of the overall production due to underground mining is bound to increase, since the vast majority of U.S. reserves (68%) are only recoverable by underground methods, and the fact that the percentage of the underground production of coal that is recovered by longwall mining is drastically increasing (1). Finally, as the nicest underground reserves are depleted, the remaining reserves will tend to be deeper, which increases the affected surface area, and under denser population concentrations, which increases the likelihood and severity of possible damages. Overall, considering the number of factor which are biased towards increasing the amount of undermined acreage, it appears that there must certainly be a corresponding increase in the number of possible damaging situations due to longwall-induced, ground subsidence.

Jan 1, 1986

By R. Bhaskar

The results of an experimental study on the dispersion and deposition characteristics of fine coal dust in mine airways are presented. Experiments were conducted at various flow velocities using bituminous and semi-anthracite-coal dust which had a large proportion of dust in the respirable size range. Cross sectional variations in the concentration of dust at various points in the airway were also measured. Instruments used in the experiments included gravimetric samplers and impactors. Concentration measurements were made both for the respirable and total airborne dust. The experimental design, sampling procedures and results are discussed. The study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground mine airways.

Jan 1, 1986

By Donald J. Murphy

Longevity of structural units, as compared to the planned useful life of a facility, always is a design consideration. Typical concerns include slow decay due to environmental factors, and changes in constitutive relationships governing the performance of the material involved. With respect to foundations, the usual items of interest are corrosion of steel and concrete, and time dependent behavior of the soil/structure system. For piles, as with other foundations, deterioration is precluded, mitigated or otherwise accounted for by assessing properly the ambient situation (sulphates, pH, stray currents, resistivity) and providing safeguards, such as resistant construction products, oversizing, coatings, and/or cathodic protection. On the other hand, long term performance of the pile foundations, as affected by time dependent characteristics of the supporting soil or rock, can be predicted and controlled only with a synergetic coupling of analyses and field tests. The history of a project for which this approach was followed forms the basis for this paper.

Jan 1, 1986

By C. E. Stack

For the purposes of this presentation, "refractory clay" is intended to include any clay suitable for refractory products and thus represents a description based on industrial application. Other common examples based on use would be white-ware clay, bleaching clay, paper clay, or cement clay. Most users and producers of refractories have specific quality requirements which determine the quality or type of clay that can be utilized. Many clays can however be interchanged or substituted in use by changing manufacturing processes or upgrading less desirable clays. U.S. Bureau of Mines publications (Ampian, 1985) categorize days into six groups. These are kaolin, fire clay, ball clay, bentonite, fuller's earth, and common clay. These are practical groupings based on clay production and usage in the United States. Among these groups bentonite, fuller's earth, and common clay are primarily composed of the minerals, smectite, illite, or chlorite, and are non-refractory. Kaolin, ball clay, and fire clay are commonly used in refractories and thus qualify as refractory clays.

Jan 1, 1986

By Michael Fehler, Hidenshi Kaieda, Leigh House

Hydraulic fracturing has gained in popularity in recent years as a way to determine the orientations and magnitudes of tectonic stresses. By augmenting conventional hydraulic fracturing measurements with detection and mapping of the microearthquakes induced by fracturing, we can supplement and independent1 y confirm information obtained from conventional analysis. Important information obtained from seismic monitoring includes: the state of stress of the rock, orientation and spacing of the major joint sets, and measurements of rock elastic parameters at locations distant from the wellbore. While conventional we1l 1ogging operations can provide information about several of these parameters, the zone of interrogation is usually limited to the immediate proximity of the borehole. The seismic waveforms of the microearthquakes contain a wealth of information about the rock in regions that are otherwise inaccessible for study. By reliably locating the hypocenters of many microearthquakes, we have inferred the joint patterns in the rock. We observed that microearthquake locations do not define a simple, thin, planar distribution, that the fault plane solutions are consistent with shear slippage, and that spectral analysis indicates that the source dimensions and slip along the faults are small. Hence we be1 ieve that the microearthquakes result from slip along preexisting joints, and not from tensile extension at the tip of the fracture. Orientations of the principal stresses can be estimated by using fault plane solutions of the larger microearthquakes. By using a joint earthquake location scheme, and/or calibrations with downhole detonators, rock velocities and heterogeneities thereof can be investigated in rock volumes that are far enough from the borehole to be representative of intrinsic rock properties.

Jan 1, 1986

By Eduardo Gonzalez Fernandez, Jaime Rios Vazquez

This report substantiates the connection that always exists between explosives and vibrations and draws attention to low frequency vibrations, which are the moat dangerous for the structures affected.

Jan 1, 1986

By D. J. Shields

This paper describes a dynamic short-nun mineral supply model that incorporates secondary processing, transportation, mineral market structure, and direct mining and milling costs. The method employed is network flow programming. Empirical tests utilizing domestic phosphate industry data have been conducted by the Bureau of Mines, U.S. Department of the Interior. In the model, nodes represent physical locations such as a mine or port. Arcs represent either a process, such as mining, or movement, such as rail or barge transport. Each arc is described by lower or minims allowable flow bounds, upper or maximum possible flow bands, and variable cost. Mines and previous period inventories represent potential supply. The model is optimized via a cost minimizing algorithm, which attempts to fulfill stated total demand at the minimum possible system cost given the arc constraints. An optimal solution of the model will predict production patterns by mineral property for each prespecified level of demand. A mineral property is defined as a separate accounting entity such as a mine. The results of serial optimizations are used to construct the short-run supply curve. Dynamic policy analysis can be conducted by altering the arc constraints.

Jan 1, 1986

By R. D. Begley

This paper will present detailed design drawings of a flexible single floor residential superstructure proposed for both longwall and room and pillar mining conditions. All efforts were made to provide an immediately available economical alter- native for future home builders on subsidence prone land. Based on this fact, a basement was not included in the design because additional costs and measures would be required to minimize cracking and leakage. A cost comparison with a traditional superstructure demonstrated that this would be a cost effective alternative. The criteria used to determine the design of the residential structure was as follows: 1. The appearance should not be different then a typical three bedroom residence; 2. Only commercially available devices and present architectural and engineering technology should be used to achieve the required "flexibility" of the super- structure; 3. The structure as completed would be capable of resisting a predetermined amount of vertical and horizontal movement; and 4. If the structure was to experience stresses beyond its capabilities, it could be easily removed from the foundation and releveled.

Jan 1, 1986

By R. J. Sweigard

Estimated costs and revenues can be used in the evaluation of post- mining land use alternatives. However, post-mining land use decisions have to be made in an environment complicated by several additional factors. These factors, including cultural, natural, and managerial issues, are not as easily quantified as costs and revenues but may be more important determinants. There- fore, some approach is needed to attach relative weight to the various factors. The concept of fuzzy sets assembled into a structured hierarchy facilitates analysis of the relative value of individual factors and their impact upon each alternative under consideration. In this paper, a method is presented which employs fuzzy set analysis to evaluate postmining land use plans on the basis of these nonquantitative factors.

Jan 1, 1986

Reduce injury to people or damage to equipment when a scheduled production blast is detonated. Approach The essential elements of an effective blast area security system were identified through case studies of five mining operations where the blast area guarding practices were considered to be superior to those generally found in the industry. These elements were used in making recommendations for improved blast area safeguarding practices. Background The blast area security system is a means by which the mine operator prevents injury to people or damage to equipment when blasting is performed. Analysis of blasting accidents showed that most blasting accidents occur during scheduled blasting and are due to inadequate blast-site security. Factors contributing to the system's breakdown are failure to clear the blast zone, inadequate guarding. and failure of personnel to follow instructions, retreat to a safe location, and/or take adequate cover. Mine personnel, visitors and even trespassers can inadvertently wander into a blasting zone unless proper procedures exist to ensure that all personnel are cleared from the blast zone and kept safely away until after blasting IS completed. Statistics show that the blaster is the miner most frequently injured In these accidents.

Jan 1, 1986

By P. Schilizzi

The increased impact of mining subsidence in the U.S. coalfields and the recent regulatory constraints legislated by government and state agencies have provoked an intense research effort on this topic by government agencies, coal companies and academic institutions. Subsidence and horizontal strain predictions are a basic requirement if subsidence and its associated effects are to be controlled and contained within acceptable environmental levels. As a result, several such prediction techniques have been proposed or are currently under development to assist coal operators in minimizing the detrimental effects of these surface deformations. VPI&SU has been actively involved in this research effort in the past few years, with particular emphasis on the Appalachian coalfield. During the initial stages of this research a large number of subsidence case studies were collected from the literature, the coal industry and government agencies. In total, data from 32 longwall panels and 60 room and pillar panels were collected. This data bank was used to determine relationships between the basic mining and subsidence parameters, in order to allow the evaluation of the various prediction methods for the Appalachian coal region. Based on this data two subsidence prediction techniques, one based on profile functions and the other on influence functions have been developed. Profile function methods provide a tool for a fast calculation of subsidence on a line across a mine panel. Influence function methods, on the other hand, allow for a more detailed calculation of ground movements, in any mode and at any depth, on a grid or at any specific point. The limitations of the data of the collected case studies, i.e. accuracy of surveys, frequency of monitoring, lack of horizontal movement measurements, etc, led VPI&SU to the initiation of a detailed subsidence and strain monitoring program above a number of active mines, located in three major coal producing counties of Virginia. The aim of this program was to enhance the data base with accurate and complete measurements of surface movements and to allow, therefore, the refinement of the prediction techniques. This paper presents this monitoring program, discusses in detail the results obtained from three specific case studies and provides recommendations for the implementation of the field data in the general prediction methods.

Jan 1, 1986

Mineral sands are being used as the source material for new "high-tech" engineering materials. One such material, Magnesia Partially Stabilized Zirconia (PSZ) has been developed and patented world-wide by CSIRO. Derived from zircon sands, the material is currently produced by Nilcra Ceramics in Australia and is exported world-wide.The properties of the material are contrary to those generally accepted for ceramics and are far more akin to those of steel. The material resists not only abrasive wear, impact and thermal shock, but does so under corrosive conditions that frequently cause early failure of metal and cemented carbide.While the consumption of mineral sands for the production of PSZ is not going to significantly increase the demand in the short term, the material itself may well assist the productivity and processing problems within the industry.

Jan 1, 1986