Search Documents

By Hayes P. C

The kinetics of reduction of PbO-silicate melts in CO-N gas mixtures at 900¦C have been studied. Rea~tion rates were measured by moni- toring the CO2 content of the product gas. A wide range of gas and melt compositions and gas flowrates have been investigated. The overall reaction rates in heterogen- eous systems are typically characterised by a steady increase as the gas flowrate is in- creased. At low flowrates the processes are limited by gas film mass transfer. At high flowrates it is expected that the rates will tend to maximum values determined by either the rate limiting chemical reaction or diffusion in the condensed phase. In the present series of experiments it has been found that for any given gas composition the overall reduction rate goes through a maximum with increasing gas flow. The maxima, which occur at relatively low gas flows, are more than an order of magni- tude greater than those observed at high gas flowrates. The results of these and other experiments are presented and analysed. Possible rate limiting mechanisms in the reaction system and their implications regarding commercial reactors are discussed.

Jan 1, 1987

The height of permanent slopes at the Panguna mine of Bougainville Copper Limited will vary from 350 to 950 metres. A few degrees difference in slope angle has a large effect on the ore/waste stripping ratio. Optimum slopes can be achieved if longer batter slopes (exceeding 45m height) are excavated using bulldozers to trim parallel to controlling fracture surfaces. Unnecessary slope flattening by incorporating benches can cost millions of dollars in lost ore. Faults and other major weaknesses, which can result in wedge failure or erodible zones have been treated successfully with shotcrete, rockbolts and cable dowels. To minimize support effort and interference with mine production, early identification and treatment of unstable areas is important.

Jan 1, 1987

By Wilton Johnson

Native asphalt was produced by four companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm. R. L. White Co., Dabney Quarry, Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by three firms: American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); Ziegler Chemical and Mineral Corp.; and Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation), from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds. Gilsonite production in 1985 declined 57% owing primarily to reduced oil well drilling activity. The value per ton was essentially unchanged.

Jan 1, 1987

By C. M. Suhr

n order to validate the borehole analysis valuation procedure commonly used in the South African gold mining industry, a simulated orebody was used to create borehole values which would serve as data for the procedure. After confirming the distribution, calculating the variance size of area relationship, estimating the block variance, and calculating a profit measurement for each set, comparisons were made to the known population parameters. Results show only one overall bias (in the estimation of the lognormal third parameter), which is carried throughout the analysis. The remainder of the analysis is unbiased, validating the procedure.

Jan 1, 1987

By Richard D. Miller

The helium resources base of the United States was estimated by the Bureau of Mines to be 1,070 Bcf as of January 1, 1985. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 280 Bcf, (2) helium in probable natural gas resources, estimated at 243 Bcf, (3) helium in possible natural gas resources, estimated to be 287 Bcf, and (4) helium in speculative natural gas resources, which makes up the remaining 260 Bcf. These helium resources are further divided into depleting, non-depleting, and stored classifications. The depleting resources are those associated with natural gasfields that are, or will be, produced for the natural gas they contain. Almost all of the helium in potential (probable, possible, and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 900 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, those in shut-in, abandoned, or otherwise nonproducing natural gasfields, are estimated to total 133 Bcf. There is 37 Bcf of helium in storage in the Federal Government-owned Cliffside Gas Field near Amarillo, TX.

Jan 1, 1987

The Quioma Mine is located along the axis of the Cordillera Oriental, 130 km southeast of Cochabamba, South Central Bolivia. Silver, lead, zinc, antimony, and gold have been intermittently produced from veins in the Quioma area since Colonial times. Mineralization occurs within steeply dipping fissure veins transecting moderately folded Lower Ordovician sediments. Tectonic activity is early to mid-Tertiary and the vein system parallels the fold axis of a major northwest-southeast striking, doubly plunging anticline. Vein sets occur within a 2 km wide band over a strike distance of 13 km along the northeast limb of the anticline. Economic mineralization occupies syntectonic pre-mineral fault zones developed in more competent stratigraphis units of Lower Ordovician clastic sediments. Veins average 55 cm in width, although mineralized structures up to 3 m wide with a known strike length of several hundred meters have been mined. Mineralization consists of siderite, argentifferous galena, sphalerite, and quartz, with minor amounts of chalcopyrite, barite, and bournonite. Pyrite is rare except at the Boston vein where it occurs with stibnite that contains trace amounts of gold. A marked characteristic of veins in the district is evidence of repeated stages of movement during mineralization. Intrusive rocks are rare in the Quioma area. Narrow porphyritic dikes of Andesitic composition averaging 1 m in thickness have been observed. These dikes occasionally show a close spatial relationship to the veins and are often kaolinized and carbonitized. Vein and dike contacts are sharp and alteration does not appear to extend into the wall rock. Mineral zoning is suggested by antimony mineralization observed in peripheral areas of the anticline.

Jan 1, 1987

By Wright J. K

A description is presented of the results of reduction experiments using a laboratory reduction apparatus in which simulation of the gas and temperature profiles which occur in direct reduction shaft furnaces is achieved using microcomputer control. The apparatus allows continously changing reduction conditions to be impressed on lump or pellet samples to simulate the environment that is experienced by iron ore burdens during their transit down the shaft of a direct reduction furnace. Three pellet samples and three lump ore samples were reduced in the apparatus. Comparative reduction curves and strengths after reduction for the materials were obtained over a range of reduction temp- eratures using Midrex-type gas compositions. The resulting reduction and strength curves show considerable variation in behaviour and reflect the physical and chemical variations in the individual ore and pellet types. A comparison is made of the reduction rates and modes of reduction of the samples reduced under "conventional" test conditions using a single unchanging gas composition and the simulated shaft furnace reduction conditions. It was observed that the course of reduction is very different in the two procedures and the major influence of temperature on the strength of the reduced product is noted.

Jan 1, 1987

By Smith DM Jr

Silver deposits, in which silver forms at least fifty percent of the value of the ore, are abundant and large on the east side of the Pacific and are absent in the western Pacific. To determine if this uneven distribution is related to features of consuming plate tectonic boundaries which dominate the metallogeny of the Pacific Rim, the variation of Ag/Au in porphyry copper deposits was used to estimate the relative silver content of magma generated in subduction zones. Porphyry copper provinces with high Ag/Au occur in regions of the eastern Pacific where silver deposits are abundant, suggesting that the distribution of silver deposits is controlled by the relative abun- dance of silver in subducted ocean crust. Ocean crust being subducted in the eastern Pacific is mostly less than 50 million years old in contrast to most ocean crust in the western Pacific which is much older. Enrich- ment of silver in young ocean crust at spread- ing centers may reflect metallogenetic evolution over geologic time. Silver may be transported to the surface in volcanic rocks, and deposits are common where felsic varieties are abundant. The high ,solubility of silver in natural waters provides a natural storage mechanism for silver weath- ered from these rocks and ultimately circulated in near-surface hydrothermal systems where many silver deposits form. The regional distribution of silver deposits is not influenced by discoverability, vertical metal zoning, or regional tectonic style. The effect of igneous differentiation is unclear.

Jan 1, 1987

By Ito H, Noguchi F, Ueda Y

DTA curves of synthesis lead sulfide and commercial. lead concentrates during oxidation were measured to clarify the mechanism of ox- idation of lead sulfide. The oxidation reac tions could be divided to elementary reactions with production of basic lead sulfates such as 2PbO PbSO4. An existance of iron sulfide played an important role of the oxidation of lead concentrates. The oxidation rates of lead sulfide were measured in the wide range of oxygen potenti- als using IR type SO2 gas-meter. The oxidation rates under low Po 2 which corresponds to the direct oxidation smelting were much lower than those obtained under high Pot. The combustion temperatures of lead sulfide were also measured by hot thermocouple method. Those values were extremly low compar- ing the oxidation temperatures obtained by DTA.

Jan 1, 1987

By Priscilla P. Nelson

Many concepts concerning equipment selection, performance prediction, and evaluation of support requirements for tunnel construction in soil or hard rock tunnels cannot be extrapolated directly for application in soft rock (compressive strength between 1.0 and 35.0 MPa). Case histories for small diameter (less than 3.5 m) tunnels in Austin, Texas, are analyzed to gain insight into particular problems encountered during tunnel excavation in weak sedimentary rock, and the performance of different excavation systems are compared.

Jan 1, 1987

By D. A. Ponniah

The installation of a pile is considered analogous to the expansion of a cylindrical cavity of a diameter equal to that of the pile. Using Vesic's theory of the expansion of cavities the effect of soil properties on pile installation loads, radial pore and total pressures are evaluated. The theoretical results are compared with load and pressure measurements made in field trials in a stiff clayey glacial till in the U.K.

Jan 1, 1987

By Mark E. White, John H. McCowan, Michael C. Costello

Minproc Engineers has carried out the design construction and commissioning of thirty two process plants in the period 1978-87. Twenty eight are gold silver recovery plants, and of these twenty two were gold alone and six were gold and silver. In most plants carbon was used for gold adsorption. Desorption has been carried out using the USBM Homestake method, the Anglo American Research Laboratories method, and the Micron Methanol method. Electrowinning has utilised steel wool, stainless steel wool, and aluminium cathodes. Electrorefining using polished stainless steel cathodes is practised. This paper summarises the experience gained in these operations

Jan 1, 1987

By Y. P. Chugh

The paper discusses laboratory and field studies to analyze time-dependent deformation behavior of immediate weak floor strata in an Illinois coal mine. In the laboratory, core samples of the immediate floor strata were subjected to incremental creep tests under unconfined compressive stress. Both axial and lateral creep deformations were recorded. Time-dependent behavior was reasonably characterized by a Burger model with one Kelvin-Voigt unit. The elastic and viscous parameter8 of the model were found to be stress-dependent, but in the range of 40% to 80% of the failure stress, the effect of stress was relatively small. Therefore, a linear visco-elastic model was developed to represent the laboratory time-dependent behavior of immediate floor strata. Such a model may be acceptable for the design of partial extraction mining systems having extraction ratios of 40% to 60%. Field observations of roof-floor convergence (floor heave) at the mine also indicated a time-dependent behavior similar to that observed in the laboratory. Field time-dependent behavior was also characterized in terms of a Burger model with one Kelvin-Voigt unit to obtain scaling factors between the field and laboratory parameters. This approach should help in predicting likely floor heave in the mine based on laboratory creep tests. It was concluded that additional studies in the field are required to arrive at more reliable correlations between the two sets of parameters.

Jan 1, 1987

The Round Hill gold-scheelite deposit is located three kilometres from Macraes Flat and approximately 60 kilometres due north of Dunedin, New Zealand. A mining feasibility study is currently being undertaken on the deposit by BHP Minerals (New Zealand) Limited, who are the managers and operators of a Joint Venture with Home Reef Mining Limited. BHP has a 70 per cent equity in the project area.

Jan 1, 1987

By C. Babbitt, J. O’Green, N. I. Jayaraman

In many mines, dust-laden air from an entry being driven by a continuous miner will contaminate the intake air to the roof bolter operator and other downwind personnel. Through a US Bureau of Mines (USBM) contract, Foster-Miller Inc. has evaluated several control techniques to reduce the respirable dust exposures of downwind personnel. One fan and tubing technique consisted of bypassing the miner-generated dust directly to the section return. The results of the evaluation of this technique revealed that reductions in dust concentrations of 90% or more can be achieved at downwind roof bolter locations. A second method was to clean the dusty air from the upwind continuous miner by using a dust collector. The cleaned air was then supplied to the bolter through collapsible tubing. An underground evaluation showed reductions of 82% to 96% when the dust collector was operating. A third method was to reduce the quantity of dust contributed by the miner to the return airstream. A water-powered scrubber was installed over the throat area of the continuous miner. More than 1.18 m3/s (2500 cfm) of dusty air moved through five tubes with dust collection efficiency exceeding 75%. Underground evaluation results showed that return dust concentrations were reduced by about 60%. This paper discusses the ventilation and dust control techniques used for personnel downwind of the continuous miner.

Jan 1, 1987

By D. B. Stephens

Assessing the occurrence of natural ground-water recharge at mine and mill waste disposal sites may be crucial to addressing regulatory agency concerns regarding the potential impact of waste seepage on ground-water resources. Recharge has been shown to occur even in semi-arid areas where annual lake evaporation exceeds precipitation. Permanent storage of waste seepage in the unsaturated zone is not to be expected if recharge occurs under natural conditions. Establishing the direction and rate of fluid movement in the vadose zone by field measurements is an important element that should be included in the site selection process.

Jan 1, 1987

By Jacques Mongrain, Serge Barbeau, Gary Brierley

The Communaute Urbaine de Montreal is currently involved in construction of the South Interceptor which consists of 53 kilometers (33 miles) of 1,800 mm (6.0 ft) to 5,400 mm (18.0 ft) diameter tunnels for the purpose of collecting, storing, and delivering sanitary and combined sewage to the treatment plant. Work is divided into ten separate contracts; nine of which have already been bid. The purpose of this paper is to describe construction activities that have been performed through the end of 1986 with emphasis on a general layout of facilities, a summary of subsurface conditions, and brief descriptions of actual construction activities for the six contracts where tunneling has been performed. All projects are being excavated with tunnel boring machines.

Jan 1, 1987

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By O. Fenn

Earlier work had shown that the use of water jets at moderate pressure enhances mechanical cutting in hard rock. To assess the potential of this technique for use in conjunction with free-rolling cutters, a series of laboratory tests was conducted with disc and button cutters to determine the effect of variations in the jet and cutting parameters on the cuter performance. In these tests it was found that the use of water jets at pressure in the range 5 to 40 MPa can reduce the forces on a free-rolling cuter by 40 per cent, which represents a significant improvement in cutting performance. The reduction in thrust force was found to be dependent on jet pressure: the greater the pressure, the greater the reduction. The reduction in rolling force was independent of jet pressure over the range investigated. The results indicate that no additional improvements in cutting performance of any significance are to be gained by an increase in jet pressure above 40 MPa. The most effective jet configuration for the reduction of cuter forces was found to be four coherent water jets, two lateraly disposed on each side of the cuter and directed at the arc of contact between the cutting edge and the rock.

Jan 1, 1987

By S. Chander

The formation of surface films on pyrite has been studied through electrochemical techniques of cyclic voltametry and AC impedance measurements. The characteristics of the surface films depend upon the conditions of oxidation and the source of pyrite. At potentials near 0.0 V, some pyrites have large values of polarization resistance showing a certain degree of passivity. Some pyrites show more passivation than the others, however. On oxidation, metastable phases of Fe(OH2) and Fe(OH3) form which transform to more stable 3 phases on aging. The growth of surface films near the corrosion potential of pyrite follows a linear kinetics which is attributed to a chemical (or an electrochemical) reaction as the rate determining step. The surface film is considered to be a hydroxide or an oxide rather than sulfur because the later is expected to be limited to a monolayer in alkaline solutions. This study has also demonstrated that AC impedance measurements can be used to study the growth characteristics of films at mineral/ solution interfaces.

Jan 1, 1987