Search Documents

By A. V. S. Meyer

The Colloquium held at Iscor, Pretoria, on 28th June, 1988, had as its objective the need for Quality Management Systems in the industry. Case studies of how problems were identified and solved by the use of such systems were submitted.

Jan 1, 1988

By R. V. Huff

An in-situ leaching technology was developed for copper oxide minerals at the Van Dyke deposit at Miami, Arizona. This paper discusses the process developed and the activities that occurred. Specifically, the activities of well installation, deposit data acquisition, leach testing and equipment development are reviewed. Installation and operation of the test facility are described.

Jan 1, 1988

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment. The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. Thi s paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flot ation and mixing"

Jan 1, 1988

By W. K. Fletcher

As part of an ongoing programme on behaviour of heavy minerals In streams, the dispersion of Au as free gold (Day and Fletcher, 1987), Sn in cassiterite (Fletcher et al, 1987) and W in scheelite (Saxby and Fletcher, 1987) have been investigated downstream of mineralization. The studies of Au and W were undertaken, in British Columbia and the Yukon Territory, respectively, in streams that are strongly influenced by spring snowmelt floods. Sn was investigated under tropical rainforest conditions in Peninnsular Malaysia.

Jan 1, 1988

New Zealand has been a significant producer of gold for over a century. Total recorded production is over 850 tonnes. There were three major periods of production: the first and biggest was between 1860 and 1880, the second was between 1895 and 1920 and the third was between 1930 and 1945. After 1945 gold production fell continually until 1980 when the major upward adjustment in gold price led to renewed interest. There have been important new developments in each of the known gold-rich areas: Westland, Otago and Coromandel and exploration for gold in these areas and in previously unprospected regions has reached unprecedented levels.

Jan 1, 1988

By D. G. C. Robertson

Counter-current staged reactors offer several advantages over batch reactors for mass transfer between two phases. Several metallurgical reactor designs have utilized the counter-current principle, e.g. the WORCA and QSL processes. But before the principle can be widely adopted, it will be necessary to overcome several significant problems. These include the need to minimize longitudinal mixing in a single reactor or to use several separate staged reactors and to carry out different reactions in sequence, e.g. phosphorus oxidation and sulfur reduction. Theoretical and experimental approaches to these problems will be discussed in the paper.

Jan 1, 1988

By Paine GG

The Kidston Gold Mine commenced mining in 1984 and current annual production is 12 million tonnes, increasing in 1990 to 18 million tonnes. Mill throughout per year is 4 million tonnes with the balance of material being waste. The operation is a conventional hard rock open pit truck and shovel operation mining 12 metre benches. Buffer blasting is utilized to minimize post blast movement of the broken rock to maintain grade control.

Jan 1, 1988

By A. Kar, J. Mazumder

"Inherent rapid cooling in laser processing often produces novel materials due to nonequilibrium partitioning during solidification. This paper reports theoretical and experimental investigations on in situ alloy formation with extended solid solution.A mathematical model for determining the composition of metastable alloys and the effects of various process parameters on the composition of extended solid solution is presented. To model the nonequilibrium partitioning of solute in concentrated solution, rate equations and conservation of mass equations are used and an expression for nonequilibrium partition coefficients is derived for concentrated solution, which is realistic for laser alloying and cladding. Effect of rapid cooling on solute segregation is presented by deriving an expression for nonequilibrium partition coefficient.Experiments were performed with Ni-AI and Ni-Hf systems to obtain the composition of solute in the extended solid solution produced during laser cladding."

Jan 1, 1988

The production of 100,000 tonnes per year of synthetic rutile from the processing of ilmenite, coal and copperas (iron sulphate) produces 200 cubic metres per hour of effluent water. A 2.0 hectare biological filter, comprising natural and man- made wetlands, has been built into the last stage of the effluent water treatment system. It is an area of shallow water (

Jan 1, 1988

By R. D. Schmidt, S. E. Follin

Introduction Mineral recovery from an in situ leaching operation is determined by the often complex interaction of hydrology, mass transport, and chemical kinetics. The operating conditions of many pilot and production scale uranium leaching operations involve heterogeneities in aquifer permeability. Differences in permeability may be naturally occurring, the result of differences in main size or cementation, or they may be induced by leaching activity. Variations in permeability directly affect the fluid flow streamline pattern, fluid flux, and so also leaching geochemistry and uranium recovery. An in situ leaching hydrology model (ISL) and a mass transport-oxidation rate model (ISLGC) have been developed for use in making site specific predictions of the leachability and productive potential of heterogeneous ore deposits, and for the optimal design of leachant injection and recovery operations. The two models are linked by output and input requirements. The ISL hydrology model generates a leachant flow streamline pattern between injection and recovery points in a flow domain incorporating regions of arbitrary permeability. The ISLGC transport model describes the changing solution concentrations of uranium and oxygen and the changing mineral concentrations of uranium and pyrite resulting from convection, longitudinal dispersion, and oxidation reactions. ISL hydrology model Basic equations The differential equation for steady-state two- dimensional flow in an isotropic porous medium is

Jan 1, 1988

By Brian Reid

"This paper studies the progress made by hydraulic shovel manufacturers over the last few years, particularly in the areas of productivity increase and operating cost reductions.Five years ago, it was widely considered that the unit production cost for a hydraulic shovel in a mining application was double that of a cable shovel in the same application. The hydraulic machine manufacturers have taken up this challenge, and modern improvements in design, coupled with changes in maintenance techniques, have narrowed the gap to the point where it is valid to ask the question ""will the cable shovel exist in ten years' time?"".Historical BackgroundThe history of the cable shovel goes back to the early 19th century and the industrial revolution. Early machines were steam-powered and ran on rails.The ""power shovel"" and the ""dragline"" were the only mechanical means of mass excavation until the early 1950s. Rail-mounted units gave way to crawlers, which increased flexibility considerably. Some shovels were redesigned as backhoes, and some became extremely large when designed as stripping shovels primarily used in North American coal mines.In the early 1950s growth in hydraulic technology spawned the introduction of the hydraulic excavator, which soon began to replace the smaller cable shovels and backhoes used in the construction industry. They were completely self-contained with either a gasoline or diesel engine and, being much lighter, were more readily transportable.As the excavators grew in size from its early models of 0.5 m3 or less, many of the cable shovel models were discontinued. This was not surprising for several reasons, but the most obvious is that both were often made by the same manufacturer."

Jan 1, 1988

By Forster I, Thilo A, Dean AK

A prototype production tool capable of operation in the hole sizes (

Jan 1, 1988

By J. E. Gebhardt, P. E. Richardson

External control of the electrochemical potential of a bed of mineral particles was investigated by the US Bureau of Mines as a method for controlling particle interaction with organic collectors and, thus, flotation response. A cylindrically shaped, 200- to 300-g bed of sulfide mineral particles was used as the working electrode in an electrochemical-flotation cell. In a pH 9.2 sodium tetraborate buffer, chalcocite floated with ethylxanthate at applied potentials [=] - 0.25 V (versus the standard hydrogen electrode) ; pyrite floated at potentials [=] 0.15 V. Differential separation of a chalcocite-pyrite mineral mixture was obtained by controlling the potential, but the flotation response of the mixture did not follow the behavior predicted from measurements on the individual mineral beds. Chalcocite dissolution products had a deleterious effect on chalcocite-pyrite separation by activating pyrite so that it floated below the potential (~ 0.13 V) at which xanthate is oxidized to dixanthogen. A pyrite bed activated with a copper(II) sulfate solution exhibited a flotation response with a potential dependence between that of chalcocite and pyrite. Pyrite dissolution products had no effect on chalcocite flotation.

Jan 1, 1988

By John J. Sammarco

As part of a project to automate coal extraction, computer control of a continuous mining machine test bed has been developed and tested by the Bureau of Mines. A computer system and control software were developed for accurate positioning of the conveyor elevation and swing, stabilizer jack, gathering head, and shear elevation. Tramming actions are also controlled by the computer. The computer system was designed to access data from sensors installed on a continuous miner and to interface with the existing control circuits of the miner. Testing in free space was used to characterize the operation of the machine. From this information, control algorithms were written and stored in the computer. The ability to control each function of the continuous miner with a high degree of accuracy and stability was successfully demonstrated in a series of tests in free space and in mining a block of simulated coal. In the mining of simulated coal, the cutting drum was instructed to position the shearer at the top of the block and shear down to the bottom under closed loop control. The cutting drum came within 0.27 in of the top and within 0.49 in of the bottom of the block for this shearing test.

Jan 1, 1988

By M. J. H. Ruscoe

"The circulation wear rates of pure nickel, cupronickel and nickel-plated-steel coins were measured and found to be in the ratio 1:3:1 . The relative wear rates of nickel and cupronickel coins were similar to those reported in earlier studies, and the circulation wear data for nickel were used as a reference in laboratory wear tests. A correlation between circulation wear rates and laboratory wear rates formed the basis for a prediction of service life using relief legibility as an 'end of life' criterion. This criterion was determined to be an average surface thickness loss of 12 um. The surf aces of nickel and Nickel-Banded-Steel (N-B-STM) coins were observed to harden both in circulation and in the laboratory tests at a rate of approximately I VHN/year of actual or simulated service life. It was also observed that the laboratory wear rate of N-B -S coins increased as nickel cladding thickness increased and this effect was attributed to differences in surface hardness.Wear test results are also reported for the new Canadian dollar coin material which shows a better wear resistance than pure nickel. IntroductionThe subject of coinage wear has a long history, and a number of studies have been published, concerned both with the measurement of circulation wear rates and with accelerated laboratory tests to simulate the behaviour of coinage materials in service. As early as 1803, wear tests were conducted by Hatchett on gold coinage using various types of vibratory and tumbling machines». These tests were commissioned by King George III of England who was concerned about the wear of gold coins in circulation.Early in this century, Adrian performed laboratory tests that showed that the wear rates of cupronickel 75/25 and nickel coins were in the ratio 3:1 and this ratio was later confirmed in laboratory tests reported by Daeppen and Zurrerw, The latter authors also weighed cupronickel and nickel coins that had been in circulation for various times and observed the same 3: I ratio. There was further support from Tylczak and Blickensderfer who reported significantly higher abrasive wear rates for cupronickel compared to nickel, when rubbed against sand paper."

Jan 1, 1988

By M. H. Moys, K. S. Liddell

The dynamics of the ball load within a wet-grinding mil are examined, using measurements of torque and load position, The test equipment provided an accurate torque measurement, and the toe and shoulder positions of the load were measured by the use of a conductivity probe mounted in the mill shell. Both the variables tested-mil filing and rotational speed-influence the position of the load, and hence the torque, and have interactive effects on both the torque and the load position, An increase in mil speed and filing causes the torque to increase to a maximum value, after which further increases in speed or filing cause the torque to decrease. The position of the load toe is influenced only by the filing up to speeds of approximately 80 per cent of critical, whereas the speed and filing both cause the load shoulder to rise as their magnitudes are increased, The power drawn by the mill is predicted by the use of published equations, and these values are compared with the measured power draw.

Jan 1, 1988

By Hungerford F

Long-hole drilling technology has rapidly advanced this decade beginning with rotary drilling/pump down camera surveying and culminating in down-hole motor drilling with cableless electronic surveying over the past two years. With the latter system, a high level of directional control is achievable in boreholes up to 1000m long. Past long-hole drilling across the industry has seen a mixture of success and failure. With these experiences, new and improved techniques and equipment have evolved. A number of long-hole drilling options are available as variations on the basic rotary and down-hole motor methods. They involve different levels of cost and equipment and vary in their suitability in different geological environments and definition of targets. Long-hole drilling is mainly target applied, either in defining geological structures in greater detail, or proving important mining areas such as longwall blocks, to be free of structures. Successful drilling hinges on a combination of drilling expertise, quality and appropriateness of equipment, understanding of geological conditions and good colliery support. Drilling expertise forms part of sound interpretation through keeping relevant records, understanding the reasons for changes in drilling conditions and implementing specific tests such as coring. The final interpretation builds upon all other available geological information. There is still scope for research into improved techniques and equipment. The use of long boreholes for geophysical surveys has high potential.

Jan 1, 1988

By Cesar O. Gomez

A procedure has been developed for mounting at random particles of mineral samples to be characterized using image analysis. The procedure is based on the generation of a random distribution of sample particles in particles of a diluent material. and the embedding of this particle mixture in an epoxy resin without disturbing the initial distribution. Two materials with atomic number similar to that of the epoxy resin were successfully used as diluents: activated charcoal and graphite. The proportion of diluent material to be mixed with the sample to have a large number of mineral particles in the field of view while keeping the occurrence of touching particles at an acceptable level was determined empirically. The randomization achieved with the procedure developed in this work was tested using as samples known mixtures of silica and pyrite particles of the same sieve class. The agreement obtained between the mass ratio of minerals used in the preparation of a particular specimen and that resulting from image analysis demonstrates that the procedure developed is successful in producing a specimen where the embedded particles are randomly distributed.

Jan 1, 1988

First, a classification of the various primary sources of feed materials for the production of cobalt is presented from a mineralogical point of view : sulfides, arsenides, sulfo-arsenides and oxide minerals. Each of these cate- gories will be characterized by its behaviour towards concentration methods, taking account of the presence of the associated minerals of other metals and of the nature of the gangue minerals. Then, for each category of cobalt bea- ring ores, typical flowsheets of treatment will be presented and discussed and the characteristics of the cobalt concentrates produced will be under- lined having in view their subsequent processing by pyro - and (or) hydrome- tallurgical methods.

Jan 1, 1988

By M. F. G. Bruce

Two backfill systems have been developed on West Driefontein, namely the centrifuge dewatered tailings system and the cyclone-classified tailings system. Modifications to the two systems since the publication of the original paper (Close and Klokow, 1985) are discussed in addition to the results obtained. Considerable experience has been gained from the operation of the centrifuge dewatering units as well as the placement of dewatered tailings in a difficult mine environment. The centrifuge dewatered tailings method has proved successful in the extraction of a highly stressed block of ground at No. 5A Sub-vertical Shaft. The utilization of backfill support in this area made it possible to dispose of a high-grade barrier pillar. This pillar was considered necessary prior to the introduction of backfill support. The recovery of the gold from this pillar made the use of dewatered tailings backfill cost- effective, despite high labour and maintenance costs. Current experience with the bagfilling method of placing cyclone- classified tailings indicates that it is viable and requires considerably less capital investment. Although expensive at present, it is envisaged that costs will decrease once cheaper bags and other forms of stope support are used. The placement of backfill in small-diameter sausage-type bags requires no change in mining cycle and allows the backfill to be placed close to the stope face. Both backfill systems are being expanded but preference is to be given to the cyclone-classified tailings system.

Jan 1, 1988