Search Documents

By R. J. Smith

Hornestake's Mclaughlin Mine is the first commercial application of pressure oxidation pretreatment of gold prior to cyanidation. Inherent to the autoclave process are several liquid/solid separations. Flocculant consumption represents a significant portion of the consumable reagent costs at McLaughlan. This paper focuses on the efforts of the Operating, Metallurgy and Engineering groups to improve thickener operation and minimize flocculant consumption. An operating philosophy incorporating feed solids control, increasing flocculant dilution water and minimizing flocculant solution shear has resulted in a reduction in 1986 flocculant costs of $0.054/t ($0.06 st) versus 1985 costs. Additional changes are projected to result in a further cost reduction of $0.20/t ($0.22/.st) in 1987.

Jan 1, 1988

By Joseph L. Walker

INTRODUCTION In looking over the diversity of the papers that are being presented during this meeting on The Industrial Practice of Fine Coal Processing one cannot help but be impressed with the progress the industry has made in beneficiating fine raw coals, and in the number of innovations that are under study to increase recovery and to improve the quality of the finest size particles produced at a preparation plant. Those who are not in our industry, who look at the technical program, might be confused, when they see that the papers include such topics as cleaning to zero and heavy media cyclone cleaning 28M x 100M; application and performance of fine coal jigs, tables, hydrocyclones, spirals, and flotation; filtration, dewatering and thermal drying; and ancilliary aspects such as fines handling, instrumentation and process control plus screening and liberation. This is an observation and not a criticism of the diversity of papers being presented. The program fits within the parameters of fine coal preparation as the term "coal preparation" is defined, but perhaps not as the term "fine coal" is defined. Admittedly these definitions are sometimes loose. However, each should be made more definitive if a meaningful fine coal preparation overview is to be possible. COAL PREPARATION DEFINED In the opinion of the writer, the term "coal preparation" should be defined as including all work activities that are performed on all components of a run-of-mine coal from the time it leaves a surface reserve or an underground portal, until all components are either ready for shipment or are stowed on, or in the earth in an environmentally acceptable manner. This definition excludes the work that is performed to improve coal quality or handleability inside the mine or pit. This work is commonly called "face" or "pit" preparation. FINE COAL DEFINED The term "fine coal" means different things to different people. In the past, anthracite finer than No. 3 Buckwheat (3/16 in.) was considered fines which often were discarded from the breaker as an unsalable by product; and bituminous coals finer that about 1/4 in. (slack) were either discarded or sold at cost to prevent an accumulation of "no bills" which referred to a product having no immediate sale. Although a standard definition of "fine coal" is yet to be accepted by the industry, a designation of coals by particle-size range has evolved through the wide use of three-circuit flowsheets, wherein the optimum size range by washer type determines the size fractions: a coarse-coal circuit for the plus 3/8 in., a -11- coal circuit for the 3/8 in. x 28 Mesh, and a fine-coal circuit for the remaining 28 Mesh x 0. Logically, the term "fine coal" should refer to some resultant size fraction or some top size by zero. This definition should include a 28 Mesh x 0 feed to a flotation cell but should exclude a 28 x 100 Mesh size fraction fed to a heavy media cyclone. Failure to include the resultant sizes in the definition precludes accounting of the full range of particle sizes present in the feed to the plant. Since the 28 Mesh x 0 fraction is treated in the final circuit of the three discreet washing circuits, now almost always used in U.S. commercial applications, and since it contains all of its resultant sizes, in the writer's opinion, it should be designated "fine coal". FINE COAL CLEANING Cleaning coal fines, which in the past was at best marginally profitable, is now an essential part of coal preparation strategy for a number of reasons : 1. Raw coals now cost more to produce and

Jan 1, 1988

By R. W. O. Kersten

Backfilling is one of the options available to the mining engineer in mine design. The decision as to the type of backfill is dependent on the purpose for which it will be used. For example, in a situation where high-grade, steeply dipping multiple reefs are to be mined, the purpose would be the following: ? to facilitate maximum extraction; a ? to minimize loss of fines; ? to allow closely spaced multiple reefs to be mined; and a ? to create a working platform. The physical properties required which will satisfy the abovementioned requirements can then be defined; the design of the fill plant, as well as the transport of the fill, will be governed by these considerations. The same procedure is also adopted in deciding on backfill in single- reef gold mines. The first question to be asked is the purpose of the fill. It may be to reduce the energy release rate, for environmental reasons, to reduce timber usage, to improve productivity, to reduce stoping costs, to obtain higher mining extraction, and so on. Only after one, or a combination, of these factors has been selected, can the specifications for the fill be decided on, and the plant designed accordingly. The introduction of backfill at Sheba Gold Mine will be used to illustrate the procedure adopted by Anglovaal in determining the type of fill required.

Jan 1, 1988

Jan 1, 1988

By R. C. Gabler

Effective recycling or disposal of flue dusts is a continuing problem, particularly for secondary smelters treating low-grade Cu scrap. The Bureau of Mines investigated a variety of flue dust treatment approaches and demonstrated the technical feasibility of a bench-scale alkaline method that includes leaching, cementation, precipitation, and roasting. Flue dust was leached at room temperature with an alkaline solution of (NH4)2C03 and NHpH to solubilize ZnO and Zn metal. Some copper, lead, tin, and most of the zinc were dissolved in the leach step. Copper, lead, and tin were recovered in the cement product. The Zn in the flltrate was precipitated by pH adjustment to neutral using CO2 injection. The Zn salt was flltered from solution and roasted to give high-purity ZnO. The leach residue, enriched from 4.3 to lOA pct Sn, could find a ready market; the metallic cement product can be recycled back to the copper converter; and the high-purity ZnO product can be sold in several markets, leaving no material for disposal. The possibility for recycling of reagents, lower energy demand, and low environmental impact make this method economically and environmentally attractive for recycling secondary copper smelter flue dusts.

Jan 1, 1988

Casting design for bench blasting in surface coal mines is a new focus and a fairly recent success. This study aims at the development of a mathematical model to predict the throw of overburden material based on geological conditions of a bench and charges in blast holes. The procedure, derived on the basis of blasting theories and dynamics of the multiple-particle system, explores the mechanisms of casting rocks into pits. Implementing the model with a computer program is a part of the study. The computer program will supply quantitative data for evaluation. It serves the purposes of verification for the model and, hopefully, field applications.

Jan 1, 1988

The increasing use of Ditch Witch trenching to define gold ore bound- aries in supergeme enriched near surface open cut mines has led to the consideration of using this technique for other sampling procedures. The use of Ditch Witch trenching for exploration has not been widely used and it is anticipated that the technique described will help stimulate more extensive use and new sampling techniques.

Jan 1, 1988

By Gostylla W

The economic feasibility of controlled district cross-cut recirculation is examined in this paper with particular reference to the most important mine ventilation network parameters. An algorithm is developed to express the annual cost of recirculation which is then compared to the annual cost of conventional ventilation using the University of Queensland Experimental Mine as a case study. The concepts of resistance ratio and volumetric efficiency ratio are introduced and used to analyse the economic feasibility of controlled recirculation within a mine ventilation network.

Jan 1, 1988

By S. M. Spottiswoode

A simple method for the application of excess shear stress (ESS) analysis to the mining of planar reefs is examined. The potential for seismicity associated with mining is expressed as the calculated increase in ESS on a regular grid of points 50 m above the reef, and is compared with observed seismicity around a deep-level, relatively geologicaly-undisturbed gold mine. Thirty regions were studied, involving over 2000 seismic events with magnitudes greater than 1,5 on the Richter scale and associated with almost 2 million square metres of stoping. The total seismicity, measured either as the number of seismic events or as the total radiated energy, corelated more closely with changes in ESS than with ERR. The incidence of rockbursts also favoured the ESS model. Corelation coeficients of around 0,8 for seismicity and ESS indicated that the assumptions inherent in the method used are collectively reasonable. The total seismicity in each region was found not to be strongly controlled by the presence of dykes and faults, although numerous individual seismic events were located close to such features.

Jan 1, 1988

By Nixon C. A

The exploration of Mount Isa Mines' new copper source will require the development of a five kilometre 4.7 x 5.5 metre blind decline commencing 1000m below the surface and extending to 1600m below the surface. With virgin rock temperatures approaching 60¦C, the ventilation strategy represents a complete departure from any previously used at this mine, in that refrigeration becomes essential. The use of direct water to air cooling techniques has become commonplace in mines throughout the world and their application is being adopted at Mount Isa Mines. A heat load simulation routine has been implemented to allow for the design of refrigeration requirements, as well as to aid in the selection of diesel or electric equipment. This enabled planners to determine the size of a surface based refrigeration plant. Future refrigeration demand for expansion into the ore production stage has also been investigated.

Jan 1, 1988

By K. Szafran, R. E. L. Seal, M. Tansey

Conversion of hydraulic equipment to fire resistant fluids has been hampered by less than satisfactory component performance and in some cases, catastrophic equipment failure. Concern over identifying possible causes to these problems led to a joint research project between the Potash Corporation of Saskatchewan Mining Limited and the University of Saskatchewan. This paper summarizes some of the results and conclusions derived from this joint project. In this study, the research was limited to evaluating the effects of potash contamination on the performance of hydraulic equipment. Two separate types of tests were conducted in order to provide a basis upon which trends could be established. This study concluded that the presence of potash dust in the hydraulic fluid can induce severe wear over relatively short periods of time. It was also deduced that a contaminant free fluid combined with proper fluid maintenance could extend the performance of hydraulic components using fire resistant fluids even under very severe operating conditions, such as elevated pressures and temperatures. Recommendations as to how to achieve this goal and the practicality of doing so are presented.

Jan 1, 1988

By J. B. Gwiazda

Introduction Thick seams constitute a considerable portion of Polish coal reserves. In producing mines and those under construction, the reserves where the height is more than 4.5 m (15 ft) total about 24v0 of all the hard coal reserves. The reserves that are under urban and industrial areas can be extracted using stowing methods for surface protection. About 50v0 of thick seam reserves can be extracted by caving methods. Thick seam mining methods Thick seams are usually extracted by multilift methods. There are some methods of thick seam mining that generally can be divided into caving and stowing methods. The stowing method is more expensive, but must be used when mining to protect surface features. The more known methods of thick seam mining include: • extraction of thick seam in ascending order with stowing; • thick seam mining in descending order with consolidated stowing; • thick seam mining with gob consolidation; • thick seam mining in descending order with roof caving; • sublevel caving thick seam mining system; and • thick seam mining system using an artificial roof. • Thick seam mining with introduction of an artificial roof The most advantageous method of thick seam mining is the method using an artificial roof. The artificial roof usually consists of wire mesh. Such wire mesh must be durable and must prevent small rock fragments from passing through. The mesh is usually made of steel properly protected against corrosion. The artificial roof is placed on the coal floor of the top slice (Fig. 1). Caving rock falls on the artificial roof and is thus separated from the coal. The next slice is extracted under the artificial roof. The producing face of the next slice must progress within 10 m (33 ft) behind the front of the first slice. As the second producing face progresses, the wire mesh moves down on the coal floor and may be used as an artificial roof for the next slice. Thus, one artificial roof allows the extraction of several consecutive slices. Application of the artificial roof allows for clean extraction and reduces coal losses. It also eliminates the hazard of spontaneous combustion. Introduction of the artificial roof has been limited due to a lack of artificial roof laying equipment. Manual laying of wire mesh is a labor-intensive operation, and it delays face progress, resulting in poor productivity. To eliminate these problems, artificial roof laying equipment was designed at the Polish Central Mining Institute. The support and the method of laying operation is covered by a patent. Artificial roof laying powered support To extract thick seams using an artificial roof; four-leg shield supports with lemniscate linkage were developed (Fig. 2). This shield is used in the first top

Jan 1, 1988

The cost-effectiveness of blasts involving radiating blastholes is cur- rently restricted in the following ways. (a) Significant percentages of potential explosion energy are not being liberated; the collar sections of some charges are being dislocated and/or desensitised by the detonations of adjacent earlier-firing charges. (b) If the minimum charge spacing is too small, detonation of an early- firing charge can initiate an adjacent charge sympathetically, thereby eliminating the benefit of any intended inter-charge delay. (c) The overall distribution of energy is poor. Appreciably better fragmentation would be achieved if current drill- ing patterns were to be replaced by staggered fans/rings having a toe spac- ing : burden ratio of about 4 : 1. This wide-spaced pattern would enable a higher percentage of the potential energy to be released, would reduce the incidence of sympathetic detonation and would provide a superior overall distribution of this liberated energy. If improved fragmentation is not required, the proposed fan/ring design should allow a significant expansion of the blasthole pattern with consequential cost savings in drill- ing, explosives and initiation.

Jan 1, 1988

The Annual Business Meeting of the members of The Rocky Mountain Coal Mining Institute held during he 84th Regular Meeting of the Institute was called to order by the president, H. Dean Jacot at 11:30 a.m Tuesday, June 28. 1988 in Peak Room 5 of Beaver Run Resort at Breckenridge, Colorado. Twenty three were present and a quorum was established. The president stated the purpose of the annual meeting is to inform members of the status of the affairs and activities of the corporation during the year. It was moved by Loren Linville, seconded and carried to approve the minutes of the previous meeting as published in the 1987 Proceedings. The chair called for reports of the various com¬mittees and these reports will he placed on file in the RMCMI office. Bylaws and Resolutions. Chairman Loren V. Linville reported there were no bylaws revisions. He further reported that the Board had adopted two resolutions: (I) Noting the passing of members since the last convention-Richard T. Brownrigg. Don A Dewey, John T. Maulshy. Hugh D. Nyquist and Mike Zakotnik. (2) Recognizing the superior skills of J. Brett Harvey. RMCMI Vice President of Utah. For recruiting 26 new members from the State of Utah and named him as #1 Recruiter in the Institute?s 1988 membership drive. Linville further commended the Executive Secretary officers, chairmen and committees loran excellent job in planning the 84th Regular Meeting and convention. Membership. In the absence of chairman Ed Sullivan. the secretary reported there are currently 718 active or dues paying members, 51 Life Members and 250 delinquent in dues payment. In the 1988 membership drive. 132 new members have been recruited and 74 of them attended this convention making up 27V, of the total attendance. Patrons of the Institute. This report was given by the secretary for chairman Ira McKeever. A total of 124 plaques has been prepared during the low year life of the program. It has been culled to 119 possible donors as some firms have gone out of business or consolidated. Of this number 46 renewed their annual $100 donation and three new Patrons have joined prior to the convention for a total of 49. During the convention. four new Patrons donated $100 each. tour former Patrons pledged $100 each and seven would be-new Patrons pledged $100 each for a total of 15. This would bring the grand total to 64 if all pledges are received prior to the close of this fiscal year as opposed to 59 renewals in 1987. Program. Co-Chairman Pete Nielsen announced the convention program theme "Broadening OUR Horizons" was well received despite the loss of three speakers during the final days prior to convention. Because the remarks of the Monday luncheon keynote speaker ran over the first time-to-be-tried Monday afternoon Poster Session was delayed almost an hour in beginning. This well thought out feature will he run again next year but in a different time frame. Nielsen thanked his co-chairmen, Bill Balaz and the Poster Session chairman Marcie Greenberg. Publicity. Chairman Tom Egan reported three newsletters including the convention newspaper were sent members during the year. He and Bob Jacob of Bob Jacob Public Relations were at registration daily to secure business card ads and to solicit advertising for the Proceedings. Scholarship. Chairman Keith McGinnis reported that six of the seven scholarship recipients were present at the convention. The University of Arizona at Tucson was added this year and it was the only university visited this year by the chairman. Each scholarship recipient was introduced to the membership at the Monday morning Welcome Session, presented a plaque and responded. The input Iron each winner was most favorable to the program. Each was appreciative of the many contacts made and the educational seminars and programs. McGinnis noted that the mining engineering department at the University of Wyoming may be dropped during the coming year. Joe Dunlap suggested that every member rally support of this department. Scholarship Award Winners: (top) Christine Gorrell-WY, Brian Memmott-UT and Andrew Kuchera-ND. (bottom) Anthony Bowler-AZ, LaVerne West-NM and Steve Newman-MT. Convention Committees Arrangements. Doris Finnie presented the following report: "In addition to the usual arrangements for this or any convention, there were others made for Special Events which included a Sunday historical tour and luncheon for 40, a Monday morning fashion show attended by 70 women. an afternoon scarf tying program for 47 with RMCMI red

Jan 1, 1988

By G. Hausen, H. Micka

"Modern signal and power electronics made adjustable-speed AC drives technically feasible and reliable and economically attractive. Cycloconverters are discussed as a proven technology for mine hoists. \IntroductionUntil rather recent technical and commercial advances in power and signal electronics, DC motors were used almost exclusively for applications requiring continuously adjustable operating speeds and torques. More recently, the significantly higher efficiency and the accordingly lower operating costs of AC motors gained importance. An effective and efficient speed control of AC motors requires the control of AC voltage and frequency. Table 1 shows typical applications of adjustable-speed AC drives.CycloconvertersOf particular interest to the mining industry are cycloconverters for hoist drives. The cycloconverter represents by far the simplest, most efficient and most economical means of converting a constant-voltage, constant-frequency supply into an adjustable-voltage, adjustable-frequency supply as required for the speed control of AC drives operating in the frequency range to half of the utility frequency.Cycloconverters feeding synchronous motors or induction motors are ideally suited for slow-speed direct-coupled drives."

Jan 1, 1988

By Yuanping H

There is a practical method of handling methane in a fully mechanized high output coal face when the methane outflow rate from the face is too high to be handled by ventilation alone, a combined method would be adopted. Before adopting this method, above all, the sources of methane outflow, which can be divided into methane in the intake airflow and methane emitted from the working seam and from the worked-out area, are determined by air-methane measure- ments in the tail gate and intake conveyor gate or by air-methane measurements in the working space of the coal face. Then, in

Jan 1, 1988

By Rao A. B, Rao V. D

Northeast of Brazil is situated in the polygon of drought. It covers some very important states like Bahia,Pernam- buco, Paraiba, Rio Grande do Norte, Cea- ra and Piaui , which have a potential for mineral production. Of them the main contributions that comes from Rio Grande do Nor to , Ceara and Paraiba are the scheelite and im portant quantities of granitic pegmatite mine- rals like tantalite-columbites, micas, beryls, precious stones, lithium minerals etc. On the other hand flourishing mineral economy in gold, tin, emeralds, chromium, lead, apatite is most- ly from Bahia; and potassium, salts, and petro- leum are from Sergipe, Alagoas and Bahia res; pectively. The most interesting aspect coninues to be the nucleus of the drought zone constituted of the Rio Grande do Norte, Paraiba and Ceara sta- tes.The first two authors have worked for twel- ve years in the region and have dedicated atten tion and time to two systems, namely skarns and granitic pegmatites. Their mineralogy,petrogra- phy, geochemistry, origin and economy is being worked upon from time to time to accompany the progress that is being achieved both in the sec tors of geology and economy. Besides, during the field campaigns, evidences have been sought to find the best guide horizons for mineralisa- tion and options for the location of target areas and prospection methods for scheelite, tantalites and other pegmatite minerals.

Jan 1, 1988

Case I- Timber Pile Test- 4 pages describe the pile driving record, the pile load test and the boring log. Case II- 24 inch square prestressed concrete pile-5 pages give details about the pile driving, the boring log, the pile driving record, and the pile load test. Case III- 12 inch square prestressed concrete pile- 5 pages describe the compilation of SPT blow counts for the whole project, the pile driving record, the pile load test and the detailed boring logs. The 70 foot long pile was driven by a Vulcan 08 pile hammer. Case IV- 12 BP 53 Steel H pile- 3 pages give the pile load test, the pile driving record and the nearest boring log. The 64 foot long pile has its tip at elevation 908 ft. and the ground is at elevation 972 ft. The contractor augered to elevation 959 ft. before driving the pile with a Conmaco 08 single acting pile hammer. The hammer had an 8000 pound ram, a rated energy of 26,000 ft-1b., and a 7 1/2 inch thick asbestos cushion. Dynamic measurements were made during driving of the test pile and measured a hammer energy equal to 12,500 foot-pounds.

Jan 1, 1988

By G. Johnston, P. K. Chatterjee, S. Holguin

Underground mine planning is largely manual and can demand considerable resources to generate a working plan and to perform limited tests of sensitivity to variations in geological and mining conditions. It is possible to use computer aided mine planning to automate many of the manual procedures to allow the planner to evaluate a number of layouts, extraction strategies, and schedules. his paper examines the simulation and scheduling of an under- ground coal mine operation through the-use of on- screen graphics. The simulation will provide a basis for predicting productivity and other relevant information over a specified number of shifts. The software developed is extremely user friendly and reduces the tedium of repetitive manual calculations inherent to mine planning and drafting to a minimum, thus offering considerable savings in an area that is widely recognized as extremely labor intensive.

Jan 1, 1988

By D. E. M. Plaumann

"The wet grinding of asbestos has attracted the attention of engineers for many years as a means of improving fibre liberation from the ore. Today, added impetus for wet grinding has resulted from a need to minimize worker exposure to asbestos dust in conventional dry mills using air, as well as a need to provide a cleaner, technically superior fibre for use by product manufacturers. However , high viscosities of asbestos slurries create transport and grinding difficulties which have been a factor impeding use of a wet grinding process.Laboratory evaluation of reagents to reduce viscosities of asbestos slurries found that one reagent, XFS-4272.00, reduced the viscosity of a 35% (by weight) slurry by 75%. The impact of XFS-4272.00 on actual grinding parameters were evaluated using a pilot plant rod mill. Slurries containing 78% solids and XFS-4272.00 were successfully milled and asbestos fibres from that milling compared favourably in liberation and relative surface area to asbestos fibres obtained from milling a 4% slurry without additives.IntroductionAlthough the use of asbestos has been declining over the last few years, the large deposits of chrysotile in eastern Canada (Quebec in particular) remain very important. Asbestos production in Canada stands ninth in volume for mineral production with over 740 000 tonnes produced in 1985. Of this quantity, 722000 tonnes were exported with a value of $446 million . Canada is second in world production of asbestos behind the U.S.S.R ."

Jan 1, 1988