Search Documents

By Denise Y. Dixon

The objectives of this study were to (1) document the hydrologic impacts of longwall mining on ground water, (2) identify the factors which affect the extent of dewatering, and (3) develop empirical trends to predict the extent of dewatering and recovery in advance of mining. The study was confined to three mine sites in north-central West Virginia. At each site, available ground water supplies were identified and monitored for dewatering effects and recovery. Mine A, located in Upshur County, West Virginia, has relatively thin overburden (approximately 715-280 feet). At this site domestic water supplies and specially constructed monitoring wells were monitored, continuing with an earlier study done by Cifelli arid Rauch. Most such supplies were completely dewatered over the longwall panel. Some of these wells have shown significant recovery, especially near a stream. Extensive monitoring of two nested piezometer wells revealed that dewatering generally started in advance of undermining in the lowermost monitored overburden zones first and then progressed upwards. Most dewatered wells completed in bedrock have shown no recovery, except. for valley drilled wells located within 100 feet of a Stream. Affected dug wells completed in valley alluvium rend located within 200 feet. of the nearest stream have shown significant recovery. Some wells have partially collapsed following mine subsidence. Mine B, having relatively thick overburden (approximately 585 to 900 feet), is located in Monongalia County, West Virginia. Ground water supply surveys have been conducted there in an attempt to study past dewatering effects. Owners reported Chat several wells were dewatered by longwall mining arid vertical air shafts that preceded longwall mining. Dewatered wells over longwall panels hove shown some recovery within 3 ½ years of mining. Mine C also has relatively thick overburden (approximately 585-900 feet), and is located mostly in Greene County, Pennsylvania. In addition to a survey of domestic water supplies at this site, five specially constructed monitoring wells were tested. The shallow monitoring wells suffered drops in water level due to mining but totally recovered within one day to three weeks after dewatering occurred. However, they did occasionally exhibit partial collapse during mine subsidence. Subsidence fracturing was beneficial in increasing the lateral hydraulic conductivity by a factor of about S to 22 for rock strata located within 124 feet of the surface, indicating enhanced shallow aquifer potential. One deep well suffered both partial dewatering and structural damage, with the state of water recovery bring uncertain. Also, two shallow domestic supplies out of five located over the mine were reportedly dewatered, but this claim could not, be substantiated.

Jan 1, 1988

Provide an accurate, reliable means for determining when a sealed mine or mine section can be safely reopened after a fire. Approach The Bureau of Mines performed a research investigation that resulted in the development of a mathematical formula for deriving a quantity, called RATIO, which can be used to define when a sealed mine or mine section has returned to safe recovery conditions after a fire. Research Results There were two major results from this Bureau research. Over a period of several years, the Bureau of Mines conducted six experiments at its Bruceton Experimental Mine in Pennsylvania. The experiments involved sealing the mine after several tons of piled coal had been allowed to burn continuously for 2 to 3 days. Although gas data obtained during the experiments revealed nothing significant, measured smoke particle levels were found to correlate with the stages of combustion and temperatures of the smoldering coal pile. Moreover, it was found that no smoke particles are produced when high-temperature smoldering exists deep within the mass of the coal pile since the smoke particles are filtered by the coal surrounding the hot region. Smoke is emitted into the mine atmosphere only if combustion is occurring near exposed surfaces. As suggested by these findings, any decision to recover a sealed mine area based primarily upon the absence of smoke particles is not a wise derision.

Jan 1, 1988

By Joan Weinberg

The real gross national product (GNP) advanced at a annual rate of 3.1 % during the second quarter, following a revised 3.4% increase in the first quarter (see table 1). Export growth continues to play an important role in the rising output. Combined with the decline in imports, it resulted in a noticeably improved trade position. Imports of consumer goods, including automobiles and food, fell while exports rose. Imported cars have been losing ground to domestic cars. The foreign car share of the U.S. market fell from 36% in October 1987, to 29% in May 1988. Business spending for new plant and equipment contributed strongly to the GNP increase. Equipment purchases, particularly of computers, rose at a 14.8% annual rate, following a large first-quarter gain. Purchases of structures rose 11.8%. The other key component of business spending, change in business inventories, declined from the first quarter. Inventory buildup in late 1987 had been considered excessive.

Jan 1, 1988

By Granholm S

The current emphasis within the mining industry to reduce the cost of production has stimulated interest in the field of maintenance and operational reliability of capital intensive mining equipuent. The failure consequences of these machines have major safety and economic implications for a mine operator. The reliability centered maintenance (RCM) approach has been found cost effective for equipment maintenance and for achieving high level system perform- ance by many organizations such as airline, military, chemical, process and manufac- turing industries. In this paper an attempt has been made to describe in brief the basic concepts of a RCM approach, the methods of RCM analysis and its cost effectiveness for maintenance of equipment. Since this approach is comparatively new for the mining industry, suitable examples are given to illustrate the case.

Jan 1, 1988

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. nonmetallic mining workforce from March through September 1986. Similar reports have been prepared for the metallic, stone, and sand and gravel mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the cool mining sector.

Jan 1, 1988

By L. P. Meade

The particular impact of imported industrial minerals varies within the Industry and is dependent upon many diverse factors. In a similar way, the impact on individuals has been varied and the degree of impact will depend partially on the individual's ability to handle change. Just as many corporations are adjusting their marketing strategy and production methods to compensate for imported mineral products; individual managers, mining engineers and geologists are making adjustments to their own personal job marketing techniques and on-the-job operating procedures. Modifying the degree of impact for both industry and individuals depends upon the ability to adapt.

Jan 1, 1988

The 91st Annual General Meeting of The South African Institute of Mining and Metallurgy was held at Kelvin House, Johannesburg, on 17th August, 1988. Mr B.c. Alberts (President) was in the Chair, and declared the meeting open at 16hOO. Obituaries The President announced the deaths of the following members of the Institute:

Jan 1, 1988

By Kenneth L. Rubow, Virgil A. Marple

"INTRODUCTION Respirable dust is defined as the dust which penetrates to the alveolated regions of the lungs. Due to the size selective nature of the particle removal mechanisms in the nasal passages and lung airways, criteria defining respirable particles must be a function of the particle size. Three criteria defining respirable particle penetration are shown in Figure 1. These criteria have been defined by the British Medical Research Council (BMRC), the American Conference of Governmental Industrial Hygienists (ACGIH) and German TBF 50-11 (1).The quantity of respirable particles in an aerosol can be measured by use of two-stage samplers. The first stage consists of a particle preclassifier with penetration characteristics corresponding to one of the respirable penetration curves in Figure 1. The large nonrespirable dust particles are removed from the airstream in the preclassifier and the smaller respirable dust particles pass on to some device which can measure their concentration (the respirable dust concentration).Instrumentation for the measurement of respirable coal mine dust has been limited by the severe conditions existing within the coal mine. The conditions of particular importance are the methane atmosphere, high humidity, and the general non-laboratory type environment. The most severe of these conditions is the methane atmosphere since any electronic or electric powered instrumentation must be intrinsically safe to operate in such an atmosphere.In spite of the difficulty of sampling respirable dust within the mines, many instruments have been developed for in mine use. Although these instruments operate under a variety of principles they generally fall within two categories: personal samplers and area samplers.A personal sampler is worn by the mines while he is performing his duties in the mine. These devices are generally small, light weight and require little power so as not to interfere with the miner's ability to work."

Jan 1, 1988

Production from a major, deep orebody requires the construction of two 6 m diameter, 1000 m deep ventilation shafts over the next three years. Further ventilation upgrades have foreshadowed an additional 1500 m of 6 m diameter shafts beyond that. After reviewing the construction alternatives it was decided to raisebore the first shaft in one pass using Western Mining Corporation's 121R raiseborer and the Wirth sequential head. The significant cost and speed of construction potential of 6 m raiseboring justified the risks associated with this new technology. Large diameter sequential head raiseboring has only been carried out in South Africa. Over the last three years many lessons have been learnt and the technology has progressed to being considered feasible. Operating practice and the optimisation of raiseboring performance for specific ground conditions are the areas requiring further work. The development of large diameter raiseboring in South Africa and the site preparation and initial operation at Z.C. Mines are described. Comment on actual operating experience includes the geotechnical investigations, the raiseborer foundations, cuttings disposal and the drilling of the pilot hole which has progressed to beyond 450 m. Unforeseen difficulties with the verticality of the pilot hole and with mud losses illustrate the types of problems that can be expected.

Jan 1, 1988

By J. Svoboda, W. J. C. Venter, R. N. Guest

SYNOPSIS Wet high-intensity magnetic separation was examined as a method for the recovery of copper and lead from Tsumeb flotation tailings. Bench-scale and pilot-plant tests were conducted and, despite the very low magnetic susceptibilities of all the complex copper and lead minerals, copper and lead recoveries of over 60 per cent and almost 50 per cent respectively were obtained at a combined copper and lead grade of up to 13,5 per cent. The recoveries were found to be practically independent of magnetic induction in the range 0,5 to 2,2 T, and the grade of the magnetic concentrate decreased with increasing magnetic induction. The grade of the magnetic concen¬trate improved when the flowrate of the slurry was increased, and desliming was found to have a profound effect on the. metallurgical process. Particles smaller than 10 µm were not recovered, and their presence in inefficiently deslimed samples impaired the overall performance of the magnetic separation

Jan 1, 1988

By R. S. Nichols

"During 1973 to 1978, Canadaka Mines Limited, a subsidiary of St. Joseph Explorations Ltd., undertook an extensive exploration and development program in the Cobalt area. This program resulted in the delineation of previously unknown stratigraphic units in the Archean volcanic sequence. During this time period, significant are controls related to area silver deposits were also identified.The Archean geology is comprised of a volcanic pile conformably overlain by sediments. The volcanics contain at least two felsic volcanic centres near the stratigraphic top of the pile. The bulk of the pile consists of mafic flows and interflow sediments. lnterflow sediments around silver are shoots contain mineralized halos of base metal sulphides. The halos exhibit lateral and vertical metal zoning with Cu, Pb and Zn mineralization decreasing away from an are shoot.Silver mineralization controls determined during the Canadaka program agree with the historically well established importance of Coleman sediments as well as Archean contacts for hosting silver deposits. The vertical extent of are shoots is typically 150to 250ft. A strong correlation was found to exist in the Cobalt area between Archean strike and the strike of are veins. Finally, al/ Cobalt area are deposits appear to be associated with a distinct volcanic pile at the top of a sequence of Archean flows."

Jan 1, 1988

By H. P. van Ormer

The objective of this paper and the developed personal computer program is not to identify or try to identify the actual total drilling cost in any Rotary Drilled Blast Bole Program. The ideas put forth here and in the computer program developed are a very accurate way to measure what is often very hard to identify and interpret -The actual direct operating cost of various drilling package combinations including comparing with available blast hole sizes and patterns

Jan 1, 1988

An image analysis system has been built which automatically digitizes camera input of rock fragments, analyses the digitised data to determine the sizes and shapes of the rock fragments, and outputs the analysed data to a printer in the form of a histogram or a scatter chart. The high speed of such a system allows for direct collection of data from material thrown into the air by blasting, material travelling on a conveyor belt, and material free-falling on to a stock-pile or into or out of a rock-crusher. Data on the blasted, un-crushed material provides information on changes in the lithology and structure of the rock face as it is quarried or mined: flatter fragments may represent approach to a brittle, unstable shear zone, or a change from sandstone to shale; so that the informa- tion reflects the effect on the sizes and shapes of the fragments by the blasting process and/or by the rock structure. The size and shape distributions of rock fragments produced during blasting and during processing may now be continuously monitored. Such detailed analysis of the results of fragmentation is labour-intensive and expensive when the size and shape distributions are obtained manually, but is cheap and efficient when using this image analysis system. Such a system will enable the results of blasting, quarrying, mining and crushing to be cheaply analysed and correlated with current and changing indus- trial practice so leading the way to increased productivity.

Jan 1, 1988

By F. E. Brinckman, G. J. Olson, D. Johnsonbaugh, T. K. Trout

"Microbiological metal recovery is an emerging technology likely to play an increasing role in commercial ore leaching, metal removal from process and waste streams, and perhaps ultimately in processing to yield metal products in specified forms or oxidation states. We are studying the potential for using microorganisms for the recovery of elements important to emerging materials technologies and for which domestic supplies are limited and/or low grade. Examples to be discussed include the bioaccumulation of yttrium and gallium. These elements are important in the production of new superconductor and semiconductor materials. However, limited domestic reserves and technologies for their recovery may cause supply problems. Microbiological processes may offer new techniques for recovery of these and other strategic elements.IntroductionMicroorganisms in ore leachingMicroorganisms assist in the commercial leaching of copper and uranium from low grade ores (1,2) and recently have been shown to have immediate commercial potential for the pretreatment of refractory gold ores to increase the gold-cyanide recovery yield (3). Copper bioleaching is the best known example of biotechnology applied to metal recovery. Copper can be recovered by commercial leaching of huge piles or dumps of low grade sulfidic ores and waste materials, which are not otherwise processable. Microbial activity in the leach dump environment oxidizes metal sulfides to soluble metal sulfates:"

Jan 1, 1988

By R. W. Smith, Z. Sadowski

INTRODUCTION Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of contaminant metal ions and other chemicals on the flotation. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances, cations such as Ca2+, Mg2+, Fe2+, and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions. Some adsorption (abstraction) experiments were also performed. Experimental materials and methods The barite used was a high-purity, naturally occur¬ring mineral sample (Kings Creek, SC). The material was ground in a porcelain mill and a fine fraction (mean particle size 11.49 µm) separated out by air elutriation. The mean size was determined by an aqueous sedimentation method using a CAHN electro-balance. In the method, an 0.6-g sample of the barite was dispersed in 450 cm3 of pH 7 water containing 0.01 g of sodium tripolyphosphate. The mean particle size was denoted X0. The stability of the barite suspensions was determined by a comparison of the mean size of the investigated barite suspension aggregations with the mean size of barite powder determined in the presence of sodium tripolyphosphate. The mean sizes (X) of the barite aggregations were determined using the same amount of water and barite sample as in the measurements of dispersed barite particle size but without the presence of polyphosphate. The ratio X/Xo is thus a measure of the stability of a suspension (the greater the ratio, the less stable the suspension). The adsorption (abstraction) experiments were carried out in polyethylene bottles containing 1 g of barite powder in 200 mL of solution. The solids were added to a solution containing a known concentration of metal chloride salts (AlCl3, FeCl2, MgCl2, and CaCl2) . The pH was controlled by both HCl and NaOH addition. The suspensions were agitated in a shaker for three hours. The final ion concentrations in solution were determined by atomic absorption analysis. The electrokinetic measurements were made using a Komline-Sanderson Zeta Reader in a conventional manner. All experiments were carried out in the presence of 1.0x10-3 k.mol/m3 NaClO4. Experimental results Figure 1 shows the zeta potential of barite particles as a function of pH in the presence of iron(II). The

Jan 1, 1988

During the 1950's there was a flurry of activity on the design of main ventilation shafts for mines. More recently, a new ana- lysis was commissioned in relation to the multi-shaft, nuclear waste isolation facili- ties currently under design in the United States. This paper presents the major find- ings of that study and should prove of value as a reference in the design of proposed new shafts. An overview of mine shaft resistance introduces the effects of the shaft walls, fittings, conveyances and shaft stations. Each of these is analyzed in turn. A com- pletely new technique is described, which facilitates the estimation of wall resis- tance. The effect of size of a conveyance is quantified and shown to be dominant when the cage occupies more than 30 per cent of the shaft cross-section. The dynamic effects of a moving conveyance are also analyzed.

Jan 1, 1988

By J. M. Mutmansky, L. Xu

"This paper outlines the results obtained when sampling twenty underground coal mine sections, each in a different mine. The sampling effort was oriented toward a detailed characterization of coal mine dusts and thus eight-stage Anderson Model 298 impactors were used as the primary collection instrument. This instrument allowed a rather detailed size distribution for each of the particulates sampled. Because four of the mines used diesel outby equipment and/or diesel shuttle cars at the face, it is possible to make some comparisons on the particulate distributions in diesel versus non-diesel mines.One of the more interesting results is the pattern that exists in mines that contain only diesels used for outby utility haulage. Particulate in these mines seem to be consistently heavy in the fine size ranges, perhaps being of significant concern to the industry. While no definite conclusions can be achieved from the limited data collected in this study, the data indicates that more detaile~ study of particulates in diesel mines is needed so that some idea of the particulate loadings in diesel mines can be achieved."

Jan 1, 1988

By Buizen M

The results of calibration trials conducted on parachute stoppings under a recently completed NERD&DC grant are presented. Applications of parachute stoppings, for rapid regulation and control of ventilation networks are described including use in mine recoveries, sealing sections and rescue work. Parachute stoppings are one of a series of non-rigid ventilation control structures specifically designed for quick installation in emergency situations, for use in high production/rapid advance areas and areas suffering roof-floor convergence.

Jan 1, 1988

Jan 1, 1988

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Also included are tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of Volume I and in the State chapters of Volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1988